Chapter 2 of 11 · 5 min read

Exam Strategy

Laws of Motion usually gives about 2–4 questions in NEET, and its ideas (free-body diagrams, F = ma, friction) sit inside many questions from other units too. Study it by drawing a free-body diagram for every problem until it becomes a habit, then practise mixed numericals against the clock.

Chapter weightage and priority

ChapterTypical NEET questionsPriorityWhy
1: Force, Inertia and Newton's First Law0–1MediumConcept and pseudo-force questions; the hanging bob in an accelerating car is a favourite
2: Momentum, Second Law and Impulse0–1HighImpulse, force–time graphs and bouncing-ball momentum change are asked often
3: Third Law and Free-Body Diagrams1–2HighLifts, blocks in contact, pulleys and Atwood machines appear almost every year
4: Conservation of Linear Momentum0–1MediumRecoil, explosions and sticking collisions; short, scoring numericals
5: Equilibrium of Concurrent Forces0–1MediumLami's theorem and string tensions; quick if you resolve forces well
6: Friction1–2HighStatic vs kinetic friction, rough inclines and stacked blocks are frequent
7: Dynamics of Uniform Circular Motion0–1HighLevel and banked roads, maximum safe speed; links to Rotational Motion

Weightage is approximate, based on recent papers; NEET can ask from any part of the syllabus.

High-yield topics

  • Apparent weight in a lift: the scale reading m(g + a) or m(g − a), and zero in free fall.

  • Blocks in contact and connected by strings: common acceleration F/(total mass) and the contact force or tension on one block.

  • Atwood machine and block-on-table pulley: acceleration, tension, and force on the pulley support.

  • Impulse and force–time graphs: impulse = area under the graph = change in momentum.

  • Momentum change in rebound: 2mv for a head-on bounce at the same speed, 2mv cos θ for an oblique bounce.

  • Static, limiting and kinetic friction: which one acts for a given push, and the friction vs applied force graph.

  • Rough inclined plane: acceleration up and down, angle of repose (tan θ = μs), force to hold or push a block.

  • Stacked blocks: the largest force for which two blocks move together.

  • Level and banked curves: v max = √(μrg), design speed v² = rg tan θ, and the banked-with-friction formula.

  • Recoil and explosions: momentum before = momentum after, often with vectors in two directions.

  • Lami's theorem and strings at angles: tensions holding a weight; why a horizontal string cannot hold a load.

  • Pseudo force: bob tilt tan θ = a/g and what an observer inside an accelerating vehicle sees.

Question types to expect

TypeWhat it looks likeHow to approach
NumericalFind acceleration, tension, friction, speed or forceDraw the free-body diagram first; write F = ma along each axis
ConceptualWhich force acts, which way, what happens if the string snapsAsk "who exerts this force on whom?" and use the three laws
Statement-based"How many of the following are correct?"Mark each statement T/F separately; watch words like always, only, never
Match the columnFour situations matched to four values or ideasSolve the easiest pair first, then eliminate options
Assertion–ReasonA claim and a causeCheck A, then R, then whether R truly explains A
Graph/diagram-basedF–t, v–t, friction vs applied force, scale reading vs timeRead slopes and areas; mark units on the axes

Study plan

DayWhat to studyPractice target
1Chapter 1: inertia, first law, frames, pseudo forceLevels 1–2 of Chapter 1 (22 MCQs)
2Chapter 2: momentum, F = dp/dt, impulse, graphsAll 30 MCQs of Chapter 2
3Chapter 3: third law, free-body diagrams, lifts, pulleysAll 30 MCQs + Level 4 of Chapter 3
4Chapter 4 and Chapter 5: momentum conservation, equilibrium30 MCQs from each chapter
5Chapter 6: friction, inclines, stacked blocksAll 45 MCQs of Chapter 6
6Chapter 7: circular motion, curves, bankingAll 45 MCQs of Chapter 7
7Revision sheets of all chapters; Unit Test (50 min)Unit Test + error log of every wrong answer

Last 48 hours:

  1. Day −2: read all seven revision sheets and the Book-at-a-glance sheet; redo every MCQ you got wrong.

  2. Day −1 morning: take Mock Test 2 in 35 minutes; check answers and reasons.

  3. Day −1 evening: tick the Common mistakes checklist and read the 40 rapid-fire facts once; sleep early.

Time-saving tricks

  • System first, then one body: for blocks moving together, get a = F/(total mass) from the whole system, then use one block to find the tension or contact force.

  • Contact force shortcut: when a force F pushes blocks m₁ and m₂, the force between them is F × (mass of the block being pushed by the contact)/(total mass).

  • Atwood machine: a = (m₁ − m₂)g/(m₁ + m₂) and T = 2m₁m₂g/(m₁ + m₂); the support force is 2T.

  • Lift check: accelerating up or decelerating while going down means the scale reads more than mg; the reverse means less. Speed alone never changes the reading.

  • Friction check: compare the applied force with μsN first. If it is smaller, friction equals the applied force and the block does not move.

  • Units elimination: impulse and momentum share N s = kg m/s; an option in N or J for impulse is wrong straight away.

  • Mass cancels: acceleration on a smooth or rough incline, v max on a curve, bank angle and bob tilt do not depend on mass. Options that change with mass are distractors.

  • 3-4-5 angles: with sin 37° = 0.6 and cos 37° = 0.8, many NEET numbers come out whole; try these first when 37° or 53° appears.

5 min left
‹
›