Chapter 9 of 11 · 25 min read

Chapter 7: Dynamics of Uniform Circular Motion

What you will learn

  • Why a body in uniform circular motion needs a net inward force

  • That centripetal force is a role played by real forces, not a new kind of force

  • The maximum safe speed of a vehicle on a level circular road

  • Banked roads without friction (optimum speed) and with friction (maximum and minimum speeds)

  • Railway curves, leaning cyclists and the conical pendulum

  • Coins on turntables, cars over humps and the rotor ride

7.1 Centripetal force

From Book 2, a body moving at constant speed v in a circle of radius r has an acceleration towards the centre:

ac=v2r=ω2ra_c = \frac{v^{2}}{r} = \omega^{2} r

By Newton's second law, a net force must point towards the centre to produce this acceleration. This net inward force is the centripetal force:

Fc=mv2r=mω2rF_c = \frac{mv^{2}}{r} = m\omega^{2} r

Centripetal force is not a new type of force. It is the name for the job of pulling a body inward. Some real force, or a combination, does that job.

SituationForce that supplies the centripetal force
Stone whirled on a string on a smooth tableTension in the string
Moon going round the EarthEarth's gravitational pull
Car turning on a level roadStatic friction of road on tyres
Car on a banked roadHorizontal part of the normal force, plus friction
Electron round a nucleus (Bohr model)Electrostatic attraction
Clothes pressed to the drum of a washing machineNormal force from the drum

The centripetal force is perpendicular to the velocity, so it changes only the direction of motion. It does no work, and the speed stays constant.

If the inward force suddenly stops, for example the string snaps, the body flies off along the tangent. This is inertia of direction (Chapter 1).

People sitting in a turning bus feel pushed outward. In the bus's rotating frame, this is described by a pseudo force, the centrifugal force, mv²/r, pointing outward. It is not a real force and it is not the reaction to centripetal force.

7.2 Vehicle on a level circular road

A car of mass m turns on a flat road of radius r. Three forces act: weight mg down, normal force N up, and static friction f along the road surface towards the centre. Vertically, N = mg. Friction alone provides the centripetal force:

f=mv2rf = \frac{mv^{2}}{r}

Static friction cannot exceed μ_s N = μ_s mg. So for a safe turn:

mv2r≤μsmg  ⇒  vmax⁡=μsrg\frac{mv^{2}}{r} \le \mu_s mg \;\Rightarrow\; v_{\max} = \sqrt{\mu_s r g}

The maximum safe speed does not depend on the mass of the vehicle. A loaded truck and a scooter have the same limit on the same curve. On a wet road μ_s drops, so v_max drops. That is why monsoon roads cause skids on curves.

The same idea applies to a coin on a rotating turntable at distance r from the axis. It stays in place only if ω²r ≤ μ_s g.

7.3 Vehicle on a banked road without friction

To depend less on friction, the outer edge of a curved road is raised. The road is tilted at angle θ to the horizontal. This is banking.

On a smooth banked road, only weight mg and normal force N act. N is perpendicular to the road, so it tilts towards the centre by θ. Split N:

Ncos⁡θ=mg,Nsin⁡θ=mv2rN\cos\theta = mg, \qquad N\sin\theta = \frac{mv^{2}}{r}

Divide the second by the first:

tan⁡θ=v2rg,v0=rgtan⁡θ\tan\theta = \frac{v^{2}}{rg}, \qquad v_0 = \sqrt{rg\tan\theta}

v₀ is the optimum speed. At this speed, no friction is needed at all, and tyre wear is least. Here N = mg/cos θ, which is more than mg.

Figure 7.1 · Forces on a car on a banked road
Figure 7.1 · Forces on a car on a banked road

The normal force tilts by θ towards the centre: its vertical part N cos θ holds up the car and its horizontal part N sin θ supplies the centripetal force, with friction helping above or below v₀.

7.4 Vehicle on a banked road with friction

If the car goes faster than v₀, it tends to slide up and out. Friction then acts down the slope. If it goes slower than v₀, it tends to slide down and in, and friction acts up the slope.

Maximum speed. Friction is limiting (f = μN) and points down the slope. Resolve vertically and horizontally:

Ncos⁡θ−μNsin⁡θ=mgN\cos\theta - \mu N\sin\theta = mg
Nsin⁡θ+μNcos⁡θ=mvmax⁡2rN\sin\theta + \mu N\cos\theta = \frac{mv_{\max}^{2}}{r}

Divide the second by the first, then divide top and bottom by cos θ:

vmax⁡=rg μ+tan⁡θ1−μtan⁡θv_{\max} = \sqrt{rg\,\frac{\mu + \tan\theta}{1 - \mu\tan\theta}}

Minimum speed. Friction is limiting and points up the slope. The same steps with μ replaced by −μ give:

vmin⁡=rg tan⁡θ−μ1+μtan⁡θv_{\min} = \sqrt{rg\,\frac{\tan\theta - \mu}{1 + \mu\tan\theta}}

If μ ≥ tan θ, v_min is zero: the car can even stand still on the curve without sliding down. Putting θ = 0 in v_max gives back √(μrg) for a level road.

RoadSpeed limitWhat supplies mv²/r
Level, with frictionv_max = √(μ r g)Friction alone
Banked, no frictionOnly v₀ = √(r g tan θ)N sin θ alone
Banked, with frictionv_min to v_maxN sin θ ± friction

7.5 Railway curves and leaning cyclists

Railway tracks. On a curve, the outer rail is raised above the inner rail by a height h. If the distance between the rails (gauge) is d, then for small angles sin θ ≈ tan θ:

h=dsin⁡θ≈dtan⁡θ=d v2rgh = d\sin\theta \approx d\tan\theta = \frac{d\,v^{2}}{rg}

Without this, the outer rail would have to push the wheel flanges sideways, which wears out both.

Cyclist on a curve. A cyclist leans inward by angle θ from the vertical. The road's contact force (normal plus friction) then passes through the centre of mass, and its horizontal part provides the centripetal force:

tan⁡θ=v2rg\tan\theta = \frac{v^{2}}{rg}

The faster the turn or the tighter the curve, the more the rider must lean.

7.6 The conical pendulum

A bob of mass m on a string of length L moves in a horizontal circle. The string sweeps out a cone, making angle θ with the vertical. The circle's radius is r = L sin θ.

Figure 7.2 · Forces on the bob of a conical pendulum
Figure 7.2 · Forces on the bob of a conical pendulum

The vertical part of tension balances the weight, and the horizontal part T sin θ points to the centre of the circle of radius L sin θ.

Forces on the bob: tension T along the string and weight mg. Vertically there is no acceleration; horizontally T sin θ supplies the centripetal force:

Tcos⁡θ=mg,Tsin⁡θ=mω2Lsin⁡θT\cos\theta = mg, \qquad T\sin\theta = m\omega^{2}L\sin\theta

From the second, T = mω²L. Putting this in the first:

ω=gLcos⁡θ,Tperiod=2πLcos⁡θg\omega = \sqrt{\frac{g}{L\cos\theta}}, \qquad T_{\text{period}} = 2\pi\sqrt{\frac{L\cos\theta}{g}}

Also tan θ = v²/(rg), the same form as the banked road and the cyclist. As the bob spins faster, θ grows, but it can never reach 90°, since T cos θ must still hold up the weight.

7.7 Two more cases

Car over a hump. A car crosses a curved bridge of radius r at its top. Weight acts down and N up; the net downward force must equal mv²/r:

mg−N=mv2r  ⇒  N=m(g−v2r)mg - N = \frac{mv^{2}}{r} \;\Rightarrow\; N = m\left(g - \frac{v^{2}}{r}\right)

The car presses less on the road than its weight. At v = √(gr), N becomes zero and the car loses contact.

Rotor ride. People stand against the wall of a large drum of radius r that spins at ω. The floor drops away. The wall's normal force N = mω²r supplies the centripetal force. Friction μN holds them up against gravity. They stay up if μ mω²r ≥ mg, that is ω ≥ √(g/(μr)).

Worked example 7.1: A 0.5 kg stone tied to a 1 m string moves in a horizontal circle on a smooth table at 4 m/s. Find the tension.

Solution: T = mv²/r = 0.5 × 16/1 = 8 N.

Worked example 7.2: A level curve has radius 50 m. μ_s between tyres and road is 0.5. Find the maximum safe speed.

Solution: v_max = √(0.5 × 50 × 10) = √250 ≈ 15.8 m/s, about 57 km/h.

Worked example 7.3: A coin rests 10 cm from the centre of a turntable. μ_s = 0.4. Find the largest angular speed at which it does not slip.

Solution: ω²r = μ_s g gives ω² = 0.4 × 10/0.1 = 40. ω = √40 ≈ 6.3 rad/s.

Worked example 7.4: A curve of radius 120 m is to be banked for 72 km/h so that no friction is needed. Find the angle.

Solution: v = 20 m/s. tan θ = v²/(rg) = 400/1200 = 1/3. θ = tan⁻¹(1/3) ≈ 18.4°.

Worked example 7.5: A road of radius 40 m is banked at 37°. μ_s = 0.5. Find the maximum and minimum safe speeds.

Solution: tan 37° = 0.75, rg = 400. v_max² = 400 × (0.5 + 0.75)/(1 − 0.375) = 400 × 1.25/0.625 = 800, so v_max ≈ 28.3 m/s. v_min² = 400 × (0.75 − 0.5)/(1 + 0.375) ≈ 72.7, so v_min ≈ 8.5 m/s. The optimum speed √(400 × 0.75) ≈ 17.3 m/s lies between them.

Worked example 7.6: Rails 1.6 m apart run on a curve of radius 400 m. Trains pass at 20 m/s. How high must the outer rail be raised?

Solution: h = dv²/(rg) = 1.6 × 400/(400 × 10) = 0.16 m = 16 cm.

Worked example 7.7: A cyclist rides at 10 m/s round a curve of radius 10√3 m. At what angle to the vertical must he lean?

Solution: tan θ = 100/(10√3 × 10) = 1/√3, so θ = 30°.

Worked example 7.8: A 0.2 kg bob on a 1 m string moves as a conical pendulum with the string at 60° to the vertical. Find the tension, angular speed and time period.

Solution: T = mg/cos 60° = 2/0.5 = 4 N. ω² = g/(L cos θ) = 10/0.5 = 20, so ω ≈ 4.47 rad/s. Period = 2π/ω ≈ 1.40 s. Check: mω²L = 0.2 × 20 × 1 = 4 N.

Worked example 7.9: A 1000 kg car crosses a hump of radius 40 m. Find (i) the force of the road on it at the top at 10 m/s, and (ii) the speed at which it would just lose contact.

Solution: (i) N = 1000 × (10 − 100/40) = 1000 × 7.5 = 7500 N. (ii) N = 0 when v = √(gr) = √400 = 20 m/s.

Quick revision

  • F_c = mv²/r = mω²r, towards the centre; supplied by real forces.

  • Centripetal force does no work; centrifugal force is a pseudo force in the rotating frame.

  • Level road: v_max = √(μ r g), independent of mass.

  • Banked, no friction: tan θ = v₀²/(rg); N = mg/cos θ.

  • Banked with friction: v_max² = rg(μ + tan θ)/(1 − μ tan θ); v_min² = rg(tan θ − μ)/(1 + μ tan θ).

  • Railway: h = dv²/(rg). Cyclist: tan θ = v²/(rg).

  • Conical pendulum: T = mω²L, ω = √(g/(L cos θ)), period 2π√(L cos θ/g).

  • Hump: N = m(g − v²/r); loses contact at √(gr).

NEET traps

  • Adding "centripetal force" as an extra arrow on a free-body diagram. It is the net inward force from the real forces you have already drawn.

  • Writing N = mg on a banked road. Without friction, N = mg/cos θ.

  • Getting the friction direction wrong on a banked road. Above v₀ it points down the slope; below v₀, up the slope.

  • Thinking a heavier car has a different safe speed on a curve. Mass cancels.

  • Using L instead of L sin θ as the radius of a conical pendulum.

  • Saying the stone flies outward along the radius when the string breaks. It leaves along the tangent.

Practice MCQs: Chapter 7

Level 1: Concept check

1. The centripetal force on a body in uniform circular motion acts (a) along the tangent (b) towards the centre (c) away from the centre (d) along the axis of rotation

2. The maximum safe speed of a car on a level circular road depends on (a) the mass of the car (b) the engine power (c) μ_s and the radius of the road (d) the colour of the car

3. The centripetal force on a car turning on a level road is supplied by (a) friction between tyres and road (b) the weight of the car (c) the normal force (d) the engine

4. Roads are banked on curves mainly to (a) increase friction (b) drain rainwater only (c) reduce the weight of the car (d) let the normal force supply part of the centripetal force

5. The optimum speed on a smooth road banked at angle θ on a curve of radius r is (a) √(rg tan θ) (b) √(rg sin θ) (c) rg tan θ (d) √(rg/tan θ)

6. A stone is whirled in a horizontal circle on a string. The string breaks. The stone moves (a) radially outward (b) towards the centre (c) along the tangent (d) in a spiral

7. If the speed of a body in a circle of fixed radius is doubled, the centripetal force becomes (a) twice (b) four times (c) half (d) unchanged

8. Centrifugal force is (a) a real force towards the centre (b) the reaction to centripetal force (c) a pseudo force seen in a rotating frame (d) a gravitational force

9. The centripetal force on the Moon is provided by (a) the Earth's gravity (b) sunlight (c) friction (d) tension

10. A cyclist going round a curve leans (a) outward (b) inward (c) backward (d) not at all

Level 2: NEET standard

11. A 0.2 kg stone tied to a 0.5 m string moves at 5 m/s in a horizontal circle on a smooth table. The tension is (a) 2 N (b) 5 N (c) 10 N (d) 20 N

12. A level curve has radius 80 m and μ_s = 0.5. The maximum safe speed is (a) 20 m/s (b) 40 m/s (c) 28.3 m/s (d) 10 m/s

13. A curve of radius 10 m is banked for a speed of 36 km/h with no friction needed. The banking angle is (a) 30° (b) 45° (c) 60° (d) 37°

14. A coin is placed 20 cm from the centre of a turntable. μ_s = 0.5. The largest angular speed without slipping is (a) 5 rad/s (b) 2.5 rad/s (c) 10 rad/s (d) 25 rad/s

15. A 1000 kg car moves at 10 m/s round a level curve of radius 50 m. The friction force on it is (a) 1000 N (b) 2000 N (c) 5000 N (d) 200 N

16. Rails 1.5 m apart run on a curve of radius 450 m. For trains at 15 m/s, the outer rail should be raised by about (a) 15 cm (b) 3.75 cm (c) 7.5 cm (d) 10 cm

17. A cyclist moves at 10 m/s round a curve of radius 10 m. His angle with the vertical is (a) 30° (b) 60° (c) 37° (d) 45°

18. A conical pendulum has a 2 m string making 60° with the vertical. Its time period is about (a) 1 s (b) 2 s (c) 2.8 s (d) 4 s

19. A car crosses the top of a hump of radius 40 m. The greatest speed at which it stays in contact with the road is (a) 20 m/s (b) 40 m/s (c) 10 m/s (d) 400 m/s

20. The work done by the centripetal force on a body in one full revolution of uniform circular motion is (a) mv² (b) 2πrF (c) zero (d) πmv²

21. The radius of a level curve is doubled, with μ_s unchanged. The maximum safe speed becomes (a) 2 times (b) √2 times (c) half (d) unchanged

22. A 1000 kg car takes a smooth banked curve (θ = 37°) at its optimum speed. The normal force on it is (a) 8000 N (b) 10000 N (c) 12500 N (d) 6000 N

Level 3: Challenge

23. A road of radius 50 m is banked at 37° with μ_s = 0.5. The maximum safe speed is about (a) 19.4 m/s (b) 31.6 m/s (c) 22.4 m/s (d) 50 m/s

24. For the road of Q23, the minimum speed at which a car does not slide down is about (a) 9.5 m/s (b) zero (c) 19.4 m/s (d) 12.5 m/s

25. A conical pendulum with a 1 m string rotates at ω = 5 rad/s. The cosine of the angle of the string with the vertical is (a) 0.8 (b) 0.5 (c) 0.4 (d) 0.25

26. In a rotor ride of radius 2 m, μ_s between riders and wall is 0.5. The least angular speed at which riders do not slip down is about (a) 3.16 rad/s (b) 10 rad/s (c) 2.24 rad/s (d) 1.58 rad/s

27. A 1500 kg car goes round a level curve of radius 60 m at 15 m/s. The least coefficient of static friction needed is (a) 0.25 (b) 0.5 (c) 0.6 (d) 0.375

28. A string can bear at most 50 N. A 0.5 kg stone tied to 1 m of it is whirled in a horizontal circle on a smooth table. The greatest speed of the stone is (a) 5 m/s (b) 7.07 m/s (c) 10 m/s (d) 100 m/s

29. Assertion (A): A vehicle can take a banked turn at its optimum speed even on a perfectly frictionless road. Reason (R): At the optimum speed, the horizontal part of the normal force alone supplies the centripetal force. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: The maximum safe speed of a car on a level circular road does not depend on its mass. Statement II: Centripetal force is a new kind of force, separate from tension, friction or gravity. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1bInward, along the radius
2cv_max = √(μ r g)
3aStatic friction points towards the centre
4dN sin θ supplies mv²/r
5atan θ = v²/(rg)
6cInertia of direction
7bF ∝ v²
8cAppears only in the rotating frame
9aGravity bends the Moon's path
10bContact force must tilt towards the centre
11c0.2 × 25/0.5
12a√(0.5 × 80 × 10)
13btan θ = 100/100 = 1
14aω² = 0.5 × 10/0.2 = 25
15bmv²/r = 1000 × 100/50
16c1.5 × 225/4500 = 0.075 m
17dtan θ = 100/100
18b2π√(2 × 0.5/10) ≈ 1.99 s
19a√(gr) = √400
20cForce is perpendicular to velocity
21bv_max ∝ √r
22cN = mg/cos 37° = 10000/0.8
23b500 × 1.25/0.625 = 1000
24a500 × 0.25/1.375 ≈ 90.9
25ccos θ = g/(ω²L) = 10/25
26aω² = g/(μr) = 10
27dμ = v²/(rg) = 225/600
28cv² = 50 × 1/0.5 = 100
29aN sin θ = mv₀²/r needs no friction
30cCentripetal force is a role, not a new force

Chapter 7 revision sheet

One-page summary

  • In uniform circular motion the speed is constant but the velocity keeps turning, so the body accelerates towards the centre.

  • Centripetal acceleration a = v²/r = ω²r. Centripetal force F = mv²/r = mω²r, always towards the centre.

  • Centripetal force is not a new force. Gravity, tension, friction, the normal force or electric attraction supplies it.

  • It is perpendicular to velocity, so it does no work and the speed stays the same.

  • If the inward force vanishes, the body moves off along the tangent (inertia of direction).

  • Centrifugal force mv²/r (outward) is a pseudo force seen only in the rotating frame.

  • Level curve: static friction supplies the inward force. Safe speed v ≤ √(μrg), independent of mass.

  • Banked road, no friction: tan θ = v²/(rg). At this design speed no friction is needed.

  • Above design speed, friction acts down the slope; below it, up the slope.

  • Banked road with friction: v max² = rg(μ + tan θ)/(1 − μ tan θ).

  • A cyclist turning leans inward by θ where tan θ = v²/(rg).

  • A coin on a turntable stays put while μg ≥ ω²r, so the farthest safe distance is μg/ω².

Fc=mv2r=mω2r,vmax⁡=μrg,tan⁡θ=v2rg,vmax⁡2=rg μ+tan⁡θ1−μtan⁡θF_c = \frac{mv^2}{r} = m\omega^2 r, \qquad v_{\max} = \sqrt{\mu r g}, \qquad \tan\theta = \frac{v^2}{rg}, \qquad v_{\max}^2 = rg\,\frac{\mu + \tan\theta}{1 - \mu\tan\theta}

Must-remember table

SituationFormulaDepends on mass?
Centripetal forcemv²/r = mω²rYes
Centripetal accelerationv²/r = ω²rNo
Level road, safe speed√(μrg)No
Banked road, design speed√(rg tan θ)No
Banked road with friction, top speed√[rg(μ + tan θ)/(1 − μ tan θ)]No
Cyclist leantan θ = v²/(rg)No
Coin on turntableω²r ≤ μgNo
String breaking limitv max = √(T max r/m)Yes

Memory aids

  • "Centre-seeking, not new": centripetal means centre-seeking; some real force always plays the role.

  • "Tan = v² over rg": the same formula gives both the bank angle and the cyclist's lean.

  • "Fast slides out, slow slides in": above design speed the car tends to slide outward (friction down the slope); below it, inward (friction up the slope).

  • "Snap = Tangent": cut the string and the stone flies along the tangent, never straight outward.

Concept connections

  • Angular speed, ω = v/r and centripetal acceleration come from Physics Book 2: Kinematics.

  • Satellites in circular orbits, where gravity is the centripetal force, are in Physics Book 6: Gravitation.

  • Charged particles moving in circles in a magnetic field (r = mv/qB) are in Physics Book 13: Magnetic Effects of Current and Magnetism.

Practice MCQs: Chapter 7, Level 4 (new NEET pattern)

31. Match List I with List II.

List I:

  • A. Safe speed on a level curve

  • B. Design speed on a frictionless banked curve

  • C. Lean angle of a turning cyclist

  • D. Centripetal acceleration

List II:

  • (i) v²/r

  • (ii) √(μrg)

  • (iii) tan⁻¹(v²/rg)

  • (iv) √(rg tan θ)

(a) A-iv, B-ii, C-iii, D-i (b) A-ii, B-iii, C-iv, D-i (c) A-ii, B-iv, C-i, D-iii (d) A-ii, B-iv, C-iii, D-i

32. Match the motion (List I) with the force that supplies the centripetal force (List II).

List I:

  • A. The Moon going round the Earth

  • B. A car turning on a level road

  • C. A stone whirled on a string on a smooth table

  • D. An electron going round the nucleus in the Bohr model

List II:

  • (i) Tension

  • (ii) Electrostatic attraction

  • (iii) Gravitational pull

  • (iv) Static friction

(a) A-iii, B-iv, C-i, D-ii (b) A-iii, B-i, C-iv, D-ii (c) A-ii, B-iv, C-i, D-iii (d) A-iii, B-iv, C-ii, D-i

33. A 1000 kg car goes round a curve of radius 25 m. Match List I with List II (g = 10 m/s²).

List I:

  • A. Safe speed on the level curve with μ = 0.4

  • B. Centripetal force at 10 m/s

  • C. No-friction speed if the curve is banked with tan θ = 0.9

  • D. Centripetal acceleration at 20 m/s

List II:

  • (i) 15 m/s

  • (ii) 16 m/s²

  • (iii) 4000 N

  • (iv) 10 m/s

(a) A-i, B-iii, C-iv, D-ii (b) A-iv, B-iii, C-i, D-ii (c) A-iv, B-ii, C-i, D-iii (d) A-iii, B-iv, C-i, D-ii

34. For a body of fixed mass in uniform circular motion, match the change (List I) with the new centripetal force as a multiple of the old (List II).

List I:

  • A. Speed doubled, radius same

  • B. Radius doubled, speed same

  • C. Speed doubled and radius doubled

  • D. Speed doubled and radius halved

List II:

  • (i) ½

  • (ii) 4

  • (iii) 8

  • (iv) 2

(a) A-ii, B-iv, C-i, D-iii (b) A-iii, B-i, C-iv, D-ii (c) A-ii, B-i, C-iv, D-iii (d) A-ii, B-i, C-iii, D-iv

35. How many of the following statements are correct?

  • A. A body in uniform circular motion has constant velocity.

  • B. The centripetal force does no work on the body.

  • C. Centripetal force is a separate kind of force, like friction or gravity.

  • D. Centrifugal force appears only to an observer in the rotating frame.

  • E. At the design speed of a banked road, no friction is needed.

(a) 2 (b) 3 (c) 4 (d) 5

36. A car goes round a banked curve that also has friction. Choose the correct set.

  • A. Above the design speed, friction on the tyres acts down the slope.

  • B. Below the design speed, friction on the tyres acts up the slope.

  • C. The top safe speed is higher than on a level curve of the same radius and μ.

  • D. The correct bank angle depends on the mass of the car.

(a) A and B only (b) B and D only (c) A, B and C only (d) A, B, C and D

37. A stone tied to a string moves in a horizontal circle on a smooth table. The string snaps. How many statements are correct?

  • A. The stone moves along the tangent at the point where the string snapped.

  • B. The stone moves radially outward.

  • C. Just after the snap, its speed is unchanged.

  • D. Before the snap, the tension supplied the centripetal force.

(a) 4 (b) 1 (c) 2 (d) 3

38. A cyclist takes a turn on a level road. Choose the correct set.

  • A. The cyclist leans towards the centre of the turn.

  • B. A heavier cyclist must lean more at the same speed and radius.

  • C. At the same speed, a sharper turn (smaller radius) needs a larger lean.

  • D. Friction from the road supplies the centripetal force.

(a) A, C and D only (b) A and B only (c) B, C and D only (d) A, B, C and D

39. For a 4 kg body moving in a circle of fixed radius, a graph of centripetal force F against v² is a straight line through the origin with slope 2 N s²/m². The radius of the circle is (a) 0.5 m (b) 8 m (c) 4 m (d) 2 m

40. Four cars take the same level curve of radius 50 m, where μs = 0.5 (g = 10 m/s²).

CarMassSpeed
P800 kg12 m/s
Q1500 kg15 m/s
R900 kg16 m/s
S1200 kg18 m/s

Which cars skid? (a) S only (b) R and S only (c) Q, R and S (d) none

41. A road curve of radius 30 m is banked so that cars at 15 m/s need no friction. The bank angle is (g = 10 m/s², tan 37° = 3/4) (a) 30° (b) 45° (c) 37° (d) 53°

Case for Q42–43: At a school science fair, a 0.5 kg stone is tied to a 1 m string and whirled in a horizontal circle on a smooth table. The string breaks if its tension goes above 50 N.

42. The largest speed the stone can have without breaking the string is (a) 10 m/s (b) 5 m/s (c) 100 m/s (d) 7.1 m/s

43. The largest number of revolutions per second, to two significant figures, is (a) 1.0 (b) 1.6 (c) 3.2 (d) 10

44. A curve of radius 30 m is banked with tan θ = 0.5. The coefficient of friction between tyres and road is 0.5. The top safe speed is (g = 10 m/s²) (a) 10 m/s (b) 15 m/s (c) 25 m/s (d) 20 m/s

45. A coin placed 4 cm from the axis of a turntable is just about to slip when the turntable spins at 10 rad/s. If the turntable spins at 20 rad/s, the farthest distance from the axis at which a coin stays put is (a) 2 cm (b) 8 cm (c) 1 cm (d) 16 cm

Level 4 answer key

QAnsReason
31dLevel: √(μrg); bank: √(rg tan θ); lean: tan⁻¹(v²/rg); a = v²/r
32aGravity, friction, tension and electric attraction in turn
33b√(0.4 × 250) = 10; 1000 × 100/25 = 4000 N; √(250 × 0.9) = 15; 400/25 = 16
34cF is proportional to v²/r: 4, ½, 2, 8
35bB, D, E true; the velocity direction changes; centripetal force is a role, not a new force
36cBank angle tan θ = v²/rg has no mass, so D is false
37dA, C, D true; it leaves along the tangent, not radially
38atan θ = v²/rg has no mass, so B is false
39dSlope = m/r, so r = 4/2 = 2 m
40bv max = √(0.5 × 50 × 10) ≈ 15.8 m/s; mass does not matter
41ctan θ = 225/300 = 0.75
42av = √(Tr/m) = √(50 × 1/0.5) = 10 m/s
43bω = v/r = 10 rad/s; f = 10/(2π) ≈ 1.6 rev/s
44dv² = 300 × (1.0/0.75) = 400
45cμg = ω²r = 100 × 0.04 = 4; new r = 4/400 = 0.01 m
25 min left
‹
›