Chapter 8: Capacitors
What you will learn
What a capacitor is, and what capacitance depends on.
The capacitance of a parallel plate capacitor, with and without a dielectric, including a partly filled gap.
What happens to Q, V, E, C and U when a dielectric is inserted with the battery connected or removed.
How to combine capacitors in series and in parallel, and solve networks.
The energy stored in a capacitor, energy density and the force between plates.
How charge shares between two capacitors, and how much energy is lost.
8.1 Capacitor and capacitance
A capacitor is two conductors separated by an insulator, used to store charge and energy. The camera flash in a phone, the starter of a ceiling fan and the circuits of every charger use capacitors.
Connect the two conductors to a battery. One gets +Q, the other −Q. The potential difference between them, V, is proportional to Q. The constant ratio is the capacitance:
SI unit: farad (F). 1 F = 1 C/V. This is a very large unit; practical values are in μF (10⁻⁶ F), nF and pF (10⁻¹² F).
Dimensional formula: [M⁻¹ L⁻² T⁴ A²].
C depends only on the size, shape and separation of the conductors and the medium between them. It does not depend on Q or V.
Isolated sphere. A sphere of radius R with charge Q has V = kQ/R (the other "plate" is at infinity).
Even the Earth (R = 6.4 × 10⁶ m) has a capacitance of only about 711 μF. This shows how large one farad is.
8.2 Parallel plate capacitor
Two flat metal plates, each of area A, face each other at a small distance d. One carries +Q and the other −Q.
Charge density on each plate: σ = Q/A.
Between the plates, the two sheet fields add (Chapter 4): E = σ/ε₀. Outside, they cancel.
The field is uniform, so V = Ed = Qd/(ε₀A).
C = Q/V:
Near the edges the field lines bulge out (fringing). We ignore this when d is much smaller than the plate size.
8.3 Parallel plate capacitor with a dielectric
Gap fully filled. A dielectric of constant K reduces the field to E₀/K for the same charge. So V drops to V₀/K, and C rises K times.
This gives a working definition: K = (capacitance with the dielectric filling the gap)/(capacitance with vacuum).
Slab of thickness t (less than d). The field is E₀ = σ/ε₀ in the air gap of total width (d − t), and E₀/K inside the slab.

The field is E₀ in the air gaps and only E₀/K inside the slab, so the voltage across the plates drops and the capacitance rises.
The position of the slab in the gap does not matter, only its thickness.
For a metal slab, K is infinite, so C = ε₀A/(d − t). A metal slab of thickness d/2 doubles C.
t = d gives back KC₀.
Two dielectrics in the gap.
| Arrangement | Acts like | Capacitance |
|---|---|---|
| Side by side, each over half the area, full gap | Two capacitors in parallel | C₀(K₁ + K₂)/2 |
| Layered, each filling half the gap, full area | Two capacitors in series | C₀ × 2K₁K₂/(K₁ + K₂) |
Inserting a dielectric: battery connected or removed. This is the most-tested idea in the chapter. Fill the whole gap with a dielectric of constant K.
| Quantity | Battery stays connected (V fixed) | Battery removed first (Q fixed) |
|---|---|---|
| Capacitance C | KC₀ | KC₀ |
| Potential difference V | V₀ | V₀/K |
| Charge Q | KQ₀ | Q₀ |
| Field between plates E | E₀ | E₀/K |
| Energy stored U | KU₀ | U₀/K |
With the battery connected, the battery pushes in extra charge, so energy rises. With the battery removed, the charge is stuck, and the slab is pulled in by the field, so stored energy falls.
8.4 Combination of capacitors

In series the same charge Q sits on every capacitor and the voltages add; in parallel every capacitor has the same voltage and the charges add.
In series. Capacitors are joined end to end. The battery charges only the outer plates. Each inner pair of plates gets equal and opposite charge by induction. So every capacitor carries the same charge Q. The voltages add.
The equivalent is smaller than the smallest capacitor.
Vᵢ = Q/Cᵢ: the smallest capacitor takes the largest voltage.
For two capacitors: Cₛ = C₁C₂/(C₁ + C₂), and V₁ = VC₂/(C₁ + C₂).
n equal capacitors C in series: C/n.
In parallel. Each capacitor is connected directly across the battery. So each has the same voltage V. The charges add.
The equivalent is larger than the largest capacitor.
Qᵢ = CᵢV: the largest capacitor takes the most charge.
n equal capacitors C in parallel: nC.
These rules are the reverse of those for resistors. Series capacitors combine like parallel resistors.
Solving networks.
Mark the junctions. Points joined by plain wire are the same point.
Reduce pure series and pure parallel groups step by step.
For a bridge, check balance: in a bridge with C₁, C₂ in the top branch and C₃, C₄ in the bottom branch, the middle capacitor carries no charge when C₁/C₂ = C₃/C₄. Then remove it.
Find the total charge, then work back to each capacitor.
8.5 Energy stored in a capacitor
Charging a capacitor means moving charge from one plate to the other against the growing voltage. When the charge is q, the voltage is q/C. Moving a further dq needs work dW = (q/C) dq.
Pick the form that matches what stays fixed: Q²/2C when Q is fixed, CV²/2 when V is fixed.
Where the energy lives. For a parallel plate capacitor, U = (1/2)(ε₀A/d)(Ed)² = (1/2)ε₀E² × (Ad). Ad is the volume between the plates. So the energy per unit volume is
The energy is stored in the field itself.
Force between the plates. Each plate sits in the field of the other plate only, which is σ/(2ε₀), half the total field.
Battery work. A battery of voltage V delivering charge Q does work QV. Only QV/2 is stored. The other half is lost as heat in the wires (and as radiation), whatever the resistance.
Energy in combinations. The total energy stored equals the sum of the energies of each capacitor, in series or in parallel.
8.6 Sharing of charge between capacitors
Capacitor C₁ at V₁ and C₂ at V₂ are joined, positive plate to positive plate. Charge flows until both have a common voltage V. Total charge is conserved.
Some energy is always lost as heat during the flow:
If the plates are joined positive to negative, charges partly cancel: V = (C₁V₁ − C₂V₂)/(C₁ + C₂), and the loss uses (V₁ + V₂)².
Worked examples
Worked example 8.1: A parallel plate capacitor has plates of area 0.02 m², 1 mm apart, in air. Find C and the charge at 100 V.
Solution: C = ε₀A/d = 8.85 × 10⁻¹² × 0.02/10⁻³ = 1.77 × 10⁻¹⁰ F = 177 pF. Q = CV = 1.77 × 10⁻¹⁰ × 100 = 1.77 × 10⁻⁸ C.
Worked example 8.2: For the capacitor of Example 8.1, find C when (a) a dielectric of K = 5 fills the gap, (b) a slab of K = 5 and thickness 0.5 mm is inserted.
Solution: (a) C = KC₀ = 5 × 177 = 885 pF. (b) d − t + t/K = 0.5 + 0.1 = 0.6 mm. C = 8.85 × 10⁻¹² × 0.02/(0.6 × 10⁻³) = 2.95 × 10⁻¹⁰ F = 295 pF.
Worked example 8.3: Capacitors of 2 μF, 3 μF and 6 μF are joined (a) in series, (b) in parallel. Find the equivalent in each case. In series across 12 V, find each voltage.
Solution: (a) 1/Cₛ = 1/2 + 1/3 + 1/6 = 1, so Cₛ = 1 μF. (b) Cₚ = 11 μF. In series, Q = 1 μF × 12 V = 12 μC on each. V = Q/C: 6 V, 4 V and 2 V. They add to 12 V. The smallest capacitor takes the largest share.
Worked example 8.4: Two 2 μF capacitors in parallel are joined in series with a 4 μF capacitor, across 10 V. Find the charge on each.
Solution: The parallel pair is 4 μF. In series with 4 μF: C = 4 × 4/8 = 2 μF. Total Q = 2 μF × 10 V = 20 μC. The 4 μF capacitor carries 20 μC (at 5 V). The pair also has 20 μC at 5 V, so each 2 μF capacitor carries 10 μC.
Worked example 8.5: Find the energy stored in a 10 μF capacitor at 200 V.
Solution: U = (1/2)CV² = 0.5 × 10⁻⁵ × 4 × 10⁴ = 0.2 J.
Worked example 8.6: A 5 μF air capacitor is charged to 100 V, and the battery is removed. A dielectric of K = 4 then fills the gap. Find the new V and the change in energy.
Solution: Q stays 500 μC. C becomes 20 μF, so V = 500/20 = 25 V. U₀ = (1/2)(5 × 10⁻⁶)(100)² = 0.025 J. U = U₀/4 = 6.25 × 10⁻³ J. The energy falls by 0.01875 J. That energy went into pulling the slab in.
Worked example 8.7: A 2 μF capacitor at 100 V is joined to a 3 μF capacitor at 50 V, like plates together. Find the common voltage and the energy lost.
Solution: V = (2 × 100 + 3 × 50)/(2 + 3) = 350/5 = 70 V. Loss = C₁C₂(V₁ − V₂)²/[2(C₁ + C₂)] = (6 × 10⁻¹² × 2500)/(10 × 10⁻⁶) = 1.5 × 10⁻³ J. Check: before, 0.01 + 0.00375 = 0.01375 J. After, (1/2)(5 × 10⁻⁶)(70)² = 0.01225 J. Difference 0.0015 J.
Worked example 8.8: Repeat Example 8.7 with the positive plate of each joined to the negative plate of the other.
Solution: Net charge = 200 − 150 = 50 μC on 5 μF. V = 10 V.
Worked example 8.9: In a bridge, the top branch has 2 μF and 4 μF in series, the bottom branch has 3 μF and 6 μF in series, and a 5 μF capacitor joins the two middle points. Find the equivalent capacitance.
Solution: Check balance: 2/4 = 3/6. The bridge is balanced, so the 5 μF capacitor carries no charge and can be removed. Top branch: 2 × 4/6 = 4/3 μF. Bottom branch: 3 × 6/9 = 2 μF. In parallel: 4/3 + 2 = 10/3 ≈ 3.33 μF.
Quick revision
C = Q/V; unit farad; isolated sphere 4πε₀R.
Parallel plate: C = ε₀A/d; full dielectric KC₀; slab ε₀A/(d − t + t/K); metal slab ε₀A/(d − t).
Series: same Q, 1/Cₛ = Σ1/Cᵢ. Parallel: same V, Cₚ = ΣCᵢ.
U = Q²/2C = CV²/2 = QV/2. Energy density ε₀E²/2. Plate force Q²/(2ε₀A).
Dielectric with battery on: Q, U rise K times. With battery off: V, E, U fall K times.
Sharing: V = (C₁V₁ + C₂V₂)/(C₁ + C₂); loss C₁C₂(V₁ − V₂)²/[2(C₁ + C₂)].
A battery stores only half the work it does; the other half becomes heat.
NEET traps
Using resistor rules for capacitors. Series capacitors combine like parallel resistors.
Forgetting whether the battery is connected when a slab is inserted. Decide what stays fixed, Q or V, first.
Using C = Kε₀A/d for a slab that only partly fills the gap.
Taking the force between plates as QE. Each plate feels only the other plate's field, E/2.
Assuming no energy is lost when charged capacitors are joined. Some is always lost unless the voltages were equal.
Mixing pF, nF and μF. Convert to farads before using formulas.
Practice MCQs: Chapter 8
Level 1: Concept check
1. One farad equals (a) 1 V/C (b) 1 C/V (c) 1 J/C (d) 1 C/J
2. The dimensional formula of capacitance is (a) [M L² T⁻⁴ A⁻²] (b) [M⁻¹ L⁻² T³ A²] (c) [M⁻¹ L⁻³ T⁴ A²] (d) [M⁻¹ L⁻² T⁴ A²]
3. The plate separation of a parallel plate capacitor is doubled. Its capacitance becomes (a) C/2 (b) 2C (c) C/4 (d) 4C
4. A dielectric of constant K fills the gap of a capacitor C. The new capacitance is (a) C/K (b) C + K (c) KC (d) K²C
5. Capacitors in series all have the same (a) voltage (b) charge (c) energy (d) capacitance
6. Capacitors in parallel all have the same (a) charge (b) energy (c) capacitance (d) voltage
7. The energy stored in a capacitor C at voltage V is (a) CV²/2 (b) CV² (c) CV/2 (d) C²V/2
8. The capacitance of an isolated sphere of radius R is (a) ε₀R (b) R/(4πε₀) (c) 4πε₀R (d) 4πε₀R²
9. The capacitance of a capacitor depends on (a) the charge on it (b) its geometry and the medium between its plates (c) the voltage across it (d) the current through it
10. The energy per unit volume in an electric field E in vacuum is (a) ε₀E (b) ε₀E² (c) E²/(2ε₀) (d) ε₀E²/2
Level 2: NEET standard
11. A parallel plate capacitor has plates of area 0.05 m², 1 mm apart, in air. Its capacitance is (a) 442.5 pF (b) 44.25 pF (c) 885 pF (d) 177 pF
12. Capacitors of 3 μF and 6 μF in series are connected across 18 V. The voltage across the 3 μF capacitor is (a) 6 V (b) 9 V (c) 12 V (d) 18 V
13. Three 6 μF capacitors are given. The ratio of the largest to the smallest capacitance that can be made from all three is (a) 3 (b) 6 (c) 18 (d) 9
14. The energy stored in a 4 μF capacitor at 50 V is (a) 1 × 10⁻⁴ J (b) 5 × 10⁻³ J (c) 1 × 10⁻² J (d) 2.5 × 10⁻³ J
15. A dielectric of constant K fills a capacitor while the battery stays connected. The stored energy becomes (a) KU (b) U/K (c) U (d) K²U
16. A charged capacitor is cut off from the battery, and a dielectric of constant K then fills the gap. The voltage becomes (a) KV (b) V (c) V/K (d) V/K²
17. A slab of K = 2 and thickness d/2 is placed in a capacitor of gap d and capacitance C. The new capacitance is (a) 2C (b) 3C/2 (c) C/2 (d) 4C/3
18. A metal slab of thickness d/2 is placed in a capacitor of gap d and capacitance C. The new capacitance is (a) C (b) 2C (c) 4C/3 (d) infinite
19. Taking the Earth as a sphere of radius 6.4 × 10⁶ m, its capacitance is about (a) 7.1 F (b) 71 μF (c) 711 μF (d) 6.4 mF
20. A 4 μF capacitor charged to 100 V is joined to an uncharged 6 μF capacitor. The common voltage is (a) 40 V (b) 60 V (c) 50 V (d) 100 V
21. Two 2 μF capacitors in parallel are joined in series with a third 2 μF capacitor. The equivalent capacitance is (a) 6 μF (b) 3 μF (c) 2/3 μF (d) 4/3 μF
22. The energy density in a field of 10⁶ V/m in air is about (a) 8.85 J/m³ (b) 4.4 J/m³ (c) 0.44 J/m³ (d) 44 J/m³
Level 3: Challenge
23. In Q20, the energy lost when the two capacitors are joined is (a) 0.012 J (b) 0.02 J (c) 0.008 J (d) zero
24. A capacitor of capacitance C₀ (air) is filled with two layers, each of half the gap, of K = 2 and K = 4. The new capacitance is (a) 3C₀ (b) 6C₀ (c) 4C₀/3 (d) 8C₀/3
25. The plates of a capacitor, each of area 0.1 m², carry ±2 μC. The force between them is about (a) 4.5 N (b) 1.13 N (c) 2.26 N (d) 0.23 N
26. In a bridge, the top branch has 1 μF and 2 μF in series, the bottom branch has 3 μF and 6 μF in series, and a 4 μF capacitor joins the middle points. The equivalent capacitance is (a) 4 μF (b) 8/3 μF (c) 2 μF (d) 16/3 μF
27. A 3 μF capacitor at 200 V and a 2 μF capacitor at 100 V are joined, positive plate of each to the negative plate of the other. The common voltage is (a) 80 V (b) 160 V (c) 140 V (d) 40 V
28. A 10 μF capacitor is charged to 100 V, cut off from the battery, and then its plate separation is doubled. The work done in pulling the plates apart is (a) 0.1 J (b) 0.025 J (c) zero (d) 0.05 J
29. Assertion (A): When a dielectric slab is slid into an isolated charged capacitor, its stored energy decreases. Reason (R): The charge on the plates decreases when the slab is inserted. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true
30. Statement I: Capacitors joined in series all have the same voltage across them. Statement II: The equivalent capacitance of capacitors in parallel is less than the smallest of them. (a) Both true (b) Both false (c) I true, II false (d) I false, II true
Answer key with reasons
| Q | Ans | Reason |
|---|---|---|
| 1 | b | C = Q/V |
| 2 | d | Q/V = A T/(M L² T⁻³ A⁻¹) |
| 3 | a | C ∝ 1/d |
| 4 | c | Field and V fall K times for the same Q |
| 5 | b | Inner plates are charged by induction |
| 6 | d | Each is across the same two points |
| 7 | a | Integrate (q/C) dq |
| 8 | c | V = kQ/R gives C = 4πε₀R |
| 9 | b | C = ε₀A/d with K for a medium |
| 10 | d | U/(Ad) for a parallel plate capacitor |
| 11 | a | 8.85 × 10⁻¹² × 0.05/10⁻³ = 4.425 × 10⁻¹⁰ F |
| 12 | c | Cₛ = 2 μF, Q = 36 μC, V = 36/3 |
| 13 | d | 18 μF/2 μF |
| 14 | b | 0.5 × 4 × 10⁻⁶ × 2500 |
| 15 | a | V fixed: U = KCV²/2 |
| 16 | c | Q fixed, C up K times |
| 17 | d | ε₀A/(d/2 + d/4) = 4C/3 |
| 18 | b | ε₀A/(d/2) |
| 19 | c | R/k = 6.4 × 10⁶/(9 × 10⁹) = 7.1 × 10⁻⁴ F |
| 20 | a | 400 μC shared over 10 μF |
| 21 | d | 4 μF in series with 2 μF: 8/6 |
| 22 | b | 0.5 × 8.85 × 10⁻¹² × 10¹² = 4.4 J/m³ |
| 23 | a | C₁C₂V²/[2(C₁ + C₂)] = 24 × 10⁻¹² × 10⁴/(2 × 10⁻⁵) |
| 24 | d | Layers in series: 2K₁K₂/(K₁ + K₂) = 16/6 |
| 25 | c | Q²/(2ε₀A) = 4 × 10⁻¹²/(1.77 × 10⁻¹²) |
| 26 | b | Balanced (1/2 = 3/6): 2/3 + 2 = 8/3 μF |
| 27 | a | (600 − 200) μC over 5 μF |
| 28 | d | Q fixed, C halves, U doubles from 0.05 J to 0.1 J |
| 29 | c | Q is fixed; U = Q²/2C falls as C rises |
| 30 | b | Series share Q, not V; parallel equivalent is the largest |
Chapter 8 revision sheet
One-page summary
A capacitor is two conductors with equal and opposite charges. C = Q/V; unit farad (F) = C V⁻¹.
C depends only on size, shape, spacing and the medium, never on Q or V.
Isolated sphere: C = 4πε₀R. The Earth's capacitance is only about 711 μF.
Parallel plates in air: C₀ = ε₀A/d. Field between plates E = σ/ε₀ = V/d.
Full dielectric: C = KC₀. Slab of thickness t: C = ε₀A/(d − t + t/K); metal slab: C = ε₀A/(d − t).
Dielectrics side by side (equal areas): C = C₀(K₁ + K₂)/2. Stacked (equal thickness): C = 2K₁K₂C₀/(K₁ + K₂).
Series: same Q, 1/C = 1/C₁ + 1/C₂ + …; result is less than the smallest. Two in series: C₁C₂/(C₁ + C₂).
Parallel: same V, C = C₁ + C₂ + …; result is more than the largest.
Energy: U = Q²/(2C) = CV²/2 = QV/2. Energy density u = ε₀E²/2 (Kε₀E²/2 in a dielectric).
The battery does work QV; half is stored and half is lost as heat in the charging wires.
Force between the plates: F = Q²/(2ε₀A) = QE/2.
Battery connected (V fixed) with dielectric: C, Q, U all become K times; E unchanged.
Battery removed (Q fixed) with dielectric: C becomes KC₀; V, E and U become 1/K times.
Sharing: common V = (C₁V₁ + C₂V₂)/(C₁ + C₂); energy lost = C₁C₂(V₁ − V₂)²/[2(C₁ + C₂)].
Balanced bridge (C₁/C₂ = C₃/C₄): the middle capacitor carries no charge and can be removed.
Must-remember table
| Change | Battery connected (V fixed) | Battery removed (Q fixed) |
|---|---|---|
| Insert dielectric K | Q × K, C × K, U × K, E same | V ÷ K, E ÷ K, U ÷ K, C × K |
| Double plate separation | C ÷ 2, Q ÷ 2, E ÷ 2, U ÷ 2 | C ÷ 2, V × 2, E same, U × 2 |
| Insert metal slab of thickness d/2 | C × 2, Q × 2 | C × 2, V ÷ 2 |
Memory aids
"Series Shares charge, Parallel Partners voltage": in series Q is common, in parallel V is common.
"Capacitors are opposite of resistors": capacitors add directly in parallel and as reciprocals in series.
"Battery On = V Owned; battery Off = Q Owned": decide first which quantity is fixed.
"Half to store, half to heat": of the battery's QV, only QV/2 is stored.
Concept connections
The series/parallel rules mirror resistor combinations in Physics Book 12: Current Electricity, but the other way round.
Capacitors in AC circuits (reactance 1/ωC, LC oscillations) are in Physics Book 14: Electromagnetic Induction and Alternating Currents.
Displacement current between capacitor plates is the starting point of Physics Book 15: Electromagnetic Waves.
Practice MCQs: Chapter 8, Level 4 (new NEET pattern)
31. Match the capacitor (List I) with its capacitance (List II).
List I:
A. Isolated sphere of radius R
B. Parallel plates in air
C. Parallel plates with the gap filled by dielectric K
D. Parallel plates with a slab of thickness t and constant K
List II:
(i) ε₀A/(d − t + t/K)
(ii) Kε₀A/d
(iii) 4πε₀R
(iv) ε₀A/d
(a) A-iii, B-iv, C-ii, D-i (b) A-iv, B-iii, C-ii, D-i (c) A-iii, B-ii, C-iv, D-i (d) A-iii, B-iv, C-i, D-ii
32. A capacitor is charged and the battery is removed. A dielectric K then fills the gap. Match the quantity (List I) with its new value (List II).
List I:
A. Charge Q
B. Voltage V
C. Stored energy U
D. Capacitance C
List II:
(i) KC₀
(ii) unchanged
(iii) U₀/K
(iv) V₀/K
(a) A-ii, B-iii, C-iv, D-i (b) A-i, B-iv, C-iii, D-ii (c) A-ii, B-iv, C-iii, D-i (d) A-ii, B-iv, C-i, D-iii
33. Match List I with List II.
List I:
A. Stored energy in terms of Q and C
B. Energy density of the field in air
C. Force between the plates
D. Work done by a battery charging C to V
List II:
(i) CV²
(ii) Q²/(2ε₀A)
(iii) ε₀E²/2
(iv) Q²/(2C)
(a) A-iii, B-iv, C-ii, D-i (b) A-iv, B-ii, C-iii, D-i (c) A-iv, B-iii, C-i, D-ii (d) A-iv, B-iii, C-ii, D-i
34. Three capacitors of 6 μF each are combined. Match the combination (List I) with the equivalent capacitance (List II).
List I:
A. All three in series
B. All three in parallel
C. Two in series, with the third in parallel across them
D. Two in parallel, with the third in series with them
List II:
(i) 9 μF
(ii) 4 μF
(iii) 18 μF
(iv) 2 μF
(a) A-iv, B-iii, C-ii, D-i (b) A-iv, B-iii, C-i, D-ii (c) A-iii, B-iv, C-i, D-ii (d) A-ii, B-iii, C-i, D-iv
35. How many of the following statements are correct?
A. Capacitors in series carry the same charge.
B. Capacitors in parallel have the same voltage.
C. The capacitance of a parallel plate capacitor depends on the charge on it.
D. While charging through a resistor, half the battery's work is lost as heat.
(a) 1 (b) 2 (c) 3 (d) 4
36. Choose the correct set of statements.
A. A metal slab of thickness d/2 placed between the plates doubles C.
B. The series equivalent of several capacitors is less than the smallest one.
C. In a dielectric, the energy density is Kε₀E²/2.
D. Joining two charged capacitors never loses energy.
(a) A and D only (b) A, B and C only (c) B and C only (d) A, B, C and D
37. With the battery kept connected, the plate separation of a parallel plate capacitor is doubled. Choose the correct set.
A. C becomes half.
B. Q becomes half.
C. E between the plates is unchanged.
D. Stored energy becomes half.
(a) A and B only (b) B and C only (c) A, B, C and D (d) A, B and D only
38. A charged capacitor is isolated (battery removed) and its plate separation is doubled. How many statements are correct?
A. V doubles.
B. E between the plates is unchanged.
C. Stored energy doubles.
D. Q becomes half.
(a) 3 (b) 2 (c) 4 (d) 1
39. A Q–V graph for a capacitor is a straight line through the origin, passing through (50 V, 200 μC). The capacitance and the energy stored at 50 V are:
(a) 0.25 μF, 5 mJ (b) 4 μF, 10 mJ (c) 4 μF, 5 mJ (d) 4 μF, 2.5 mJ
40. Two capacitors are charged separately and then joined, positive plate to positive plate.
| Capacitor | C | Charged to |
|---|---|---|
| C₁ | 2 μF | 100 V |
| C₂ | 3 μF | 50 V |
The common potential and the energy lost are:
(a) 70 V, 1.5 mJ (b) 75 V, 1.5 mJ (c) 70 V, 3 mJ (d) 80 V, 0.75 mJ
41. A graph shows C against the thickness t of a slab (K = 3) placed in a 6 mm gap. At t = 0, C = 10 pF. The value of C at t = 3 mm is:
(a) 30 pF (b) 12 pF (c) 20 pF (d) 15 pF
Case for Q42–43: A camera flash uses a 10 μF capacitor. It is charged to 200 V, the charger is disconnected, and a dielectric of K = 2 is then slid fully into the gap.
42. The new voltage across the capacitor is:
(a) 400 V (b) 100 V (c) 200 V (d) 50 V
43. The change in stored energy is:
(a) increases by 0.1 J (b) no change (c) decreases by 0.1 J (d) decreases by 0.2 J
44. A 2 μF and a 4 μF capacitor are in series, and a 3 μF capacitor is connected across this pair. The whole set is joined to a 12 V battery. The voltage across the 4 μF capacitor is:
(a) 4 V (b) 8 V (c) 6 V (d) 12 V
45. Two dielectrics K₁ = 2 and K₂ = 4 fill a parallel plate capacitor, first side by side (each over half the area), then stacked (each half the thickness). The ratio C(side by side) : C(stacked) is:
(a) 8 : 9 (b) 9 : 8 (c) 3 : 2 (d) 1 : 1
Level 4 answer key
| Q | Ans | Reason |
|---|---|---|
| 31 | a | Standard capacitance results |
| 32 | c | Q fixed; C × K so V ÷ K and U = Q²/(2C) ÷ K |
| 33 | d | U = Q²/(2C), u = ε₀E²/2, F = Q²/(2ε₀A), W_battery = QV = CV² |
| 34 | b | 6/3 = 2; 3 × 6 = 18; 3 + 6 = 9; (12 × 6)/18 = 4 μF |
| 35 | c | A, B, D true; C depends only on geometry and medium |
| 36 | b | Joining capacitors at different potentials always loses energy |
| 37 | d | V fixed, d doubled: C, Q, U halve; E = V/d also halves |
| 38 | a | Q fixed: C halves, V doubles, E = σ/ε₀ unchanged, U doubles |
| 39 | c | C = 200 μC/50 V = 4 μF; U = QV/2 = 5 mJ |
| 40 | a | V = (200 + 150)/5 = 70 V; loss = 6 × 10⁻¹² × 2500/(10 × 10⁻⁶) = 1.5 mJ |
| 41 | d | C = C₀d/(d − t + t/K) = 10 × 6/(6 − 3 + 1) = 15 pF |
| 42 | b | Q fixed, C doubles, so V = 200/2 = 100 V |
| 43 | c | U goes from 0.2 J to 0.1 J; the field pulls the slab in |
| 44 | a | Series pair = 4/3 μF across 12 V, Q = 16 μC; V on 4 μF = 16/4 = 4 V |
| 45 | b | Side by side 3C₀; stacked 2(2)(4)/(6) C₀ = 8C₀/3; ratio 9 : 8 |