Chapter 4 of 10 · 27 min read

Chapter 2: Distillation and Differential Extraction

What you will learn

  • How boiling point depends on vapour pressure and outside pressure.

  • When to use simple distillation, fractional distillation, distillation under reduced pressure and steam distillation.

  • How a fractionating column works, and why steam distillation happens below 373 K.

  • How to calculate the composition of a steam distillate.

  • The principle of differential extraction, the distribution coefficient, and why several small extractions beat one big one.

2.1 Boiling point and vapour pressure

Every liquid sends molecules into the space above it. The pressure of this vapour is the vapour pressure. It rises steeply with temperature.

A liquid boils when its vapour pressure becomes equal to the outside pressure. At sea level that outside pressure is 760 mm Hg.

Your pressure cooker uses this rule in one direction. It raises the pressure inside, so water boils above 373 K and dal cooks faster. On a hill station the air pressure is lower, so water boils below 373 K and cooking is slower. Distillation uses this rule in both directions.

Distillation means boiling a liquid, condensing the vapour, and collecting the condensed liquid (the distillate). Liquids with different volatilities can be separated this way, and non-volatile impurities stay behind.

2.2 Simple distillation

Simple distillation is used when:

  • a volatile liquid has to be separated from a non-volatile impurity, or

  • two liquids have boiling points that are far apart, and neither decomposes at its boiling point.

A standard example is chloroform (bp 334 K) and aniline (bp 457 K). On heating, chloroform boils first and is collected. The temperature then rises, and aniline distils later into a fresh receiver.

The set-up has a distillation flask, a thermometer, a water condenser and a receiver. Three details are tested often:

  1. The thermometer bulb sits just at the level of the side arm. It must read the temperature of the vapour that is leaving, not of the boiling liquid.

  2. Cooling water enters the condenser at the lower end and leaves at the upper end. The jacket then stays completely full, and the cold water meets the vapour that is already partly cooled.

  3. A few porous porcelain pieces are added to the flask. They give a steady stream of small bubbles and prevent violent bumping.

2.3 Fractional distillation

When two liquids boil close together, the vapour from the flask contains a lot of both. Simple distillation then gives poor separation.

The fix is a fractionating column fitted between the flask and the condenser. The column is packed with glass beads or has many glass plates. It gives a large surface on which the rising vapour repeatedly condenses and re-vaporises.

Each condense-and-boil step enriches the vapour in the lower-boiling (more volatile) liquid. Many such steps happen up the column. Each one is called a theoretical plate. By the time the vapour reaches the top, it is almost pure lower-boiling liquid. The higher-boiling liquid runs back down into the flask.

Uses:

  • Separating liquids with close boiling points, such as acetone (329 K) and methanol (338 K).

  • Separating crude oil into fractions (petrol, kerosene, diesel and more) in a petroleum refinery.

  • Recovering pure solvents from used solvent mixtures whose boiling points are close.

Figure 2.1 · Fractional distillation set-up
Figure 2.1 · Fractional distillation set-up

Read the figure bottom to top: vapour rises through the bead-packed column, the thermometer bulb sits at the side arm, and only the lower-boiling liquid reaches the condenser and receiver.

2.4 Distillation under reduced pressure

Some liquids decompose at or below their normal boiling point. Heating them to boil at 1 atm would destroy them.

The answer is to lower the pressure above the liquid with a water pump or vacuum pump. A liquid boils when its vapour pressure equals the outside pressure. So at lower outside pressure, it boils at a lower temperature, safely below where it decomposes.

The classic example is glycerol. In the soap industry, glycerol is recovered from spent lye by distillation under reduced pressure. Glycerol would decompose at its normal boiling point.

2.5 Steam distillation

Steam distillation purifies liquids or solids that are:

  • steam volatile (they have a noticeable vapour pressure near 373 K), and

  • immiscible with water.

Steam from a steam generator is passed through the heated flask holding the impure substance and some water. The vapour of the organic compound and of water pass over together, condense, and collect in the receiver. Because the two do not mix, they form two layers there and are easily separated with a separating funnel.

Why it boils below 373 K. In a mixture of two immiscible liquids, each liquid exerts its own full vapour pressure, independent of the other. The total pressure is the sum:

ptotal=pwater+porganicp_{\text{total}} = p_{\text{water}} + p_{\text{organic}}

The mixture boils when this total reaches the outside pressure, 760 mm Hg. Since p_organic adds to p_water, the total reaches 760 mm Hg before water alone would. So the mixture boils below 373 K. The organic compound distils at a temperature far below its own boiling point, so it does not decompose.

How much organic compound distils. In the vapour, the mole ratio of the two components equals the ratio of their partial pressures (Dalton's law). Writing moles as mass over molar mass:

norgnwater=porgpwater⇒morgmwater=porg Morgpwater Mwater\frac{n_{\text{org}}}{n_{\text{water}}} = \frac{p_{\text{org}}}{p_{\text{water}}} \quad \Rightarrow \quad \frac{m_{\text{org}}}{m_{\text{water}}} = \frac{p_{\text{org}} \, M_{\text{org}}}{p_{\text{water}} \, M_{\text{water}}}

This is why steam distillation works well for heavy molecules. Even a small vapour pressure gives a good mass of product, because M_org is much larger than 18.

Uses:

  • Separating aniline from an aniline–water mixture.

  • Extracting essential oils (such as from rose petals, eucalyptus leaves or cloves) from plant material.

  • Separating o-nitrophenol (steam volatile) from p-nitrophenol (not steam volatile).

Figure 2.2 · Steam distillation set-up
Figure 2.2 · Steam distillation set-up

Steam from the generator bubbles through the impure substance; the organic compound and water distil together and settle as two layers in the receiver.

2.6 Differential extraction

Often an organic compound is dissolved in water, for example after a reaction. You cannot always boil the water off, because the compound may be heat-sensitive.

In differential extraction, the aqueous solution is shaken with an organic solvent that:

  • does not mix with water, and

  • dissolves the compound much better than water does.

Common solvents are diethyl ether, chloroform, dichloromethane and benzene. The compound passes from water into the organic layer. The layers are then separated in a separating funnel, and the solvent is removed by distillation or evaporation to leave the compound.

Steps.

  1. Pour the aqueous solution and the organic solvent into a separating funnel.

  2. Stopper it, invert it, and shake. Open the tap now and then to release vapour pressure.

  3. Clamp it and let the two layers settle.

  4. Run off the lower layer through the tap. Pour the upper layer out from the top.

  5. Distil or evaporate the organic solvent to recover the compound.

The denser liquid forms the lower layer. Diethyl ether (density about 0.71 g/mL) floats on water. Chloroform (about 1.48 g/mL) sinks below water.

Figure 2.3 · Separating funnel in differential extraction
Figure 2.3 · Separating funnel in differential extraction

The two immiscible liquids settle by density: the lower layer is run off through the stopcock, and the upper layer is poured out from the top.

The distribution law. At a fixed temperature, a solute shared between two immiscible liquids settles at a fixed ratio of concentrations. This ratio is the distribution (partition) coefficient:

KD=CorganicCaqueousK_D = \frac{C_{\text{organic}}}{C_{\text{aqueous}}}

Suppose W g of compound is in V_aq mL of water, and is shaken once with V_org mL of solvent. Let x g stay in water. Then (W − x) g goes into the organic layer, and

KD=(W−x)/Vorgx/Vaq⇒x=W VaqVaq+KDVorgK_D = \frac{(W - x)/V_{\text{org}}}{x/V_{\text{aq}}} \quad \Rightarrow \quad x = W \, \frac{V_{\text{aq}}}{V_{\text{aq}} + K_D V_{\text{org}}}

Repeating with fresh solvent n times, each time leaving the same fraction behind:

xn=W(VaqVaq+KDVorg)nx_n = W \left( \frac{V_{\text{aq}}}{V_{\text{aq}} + K_D V_{\text{org}}} \right)^{n}

The practical rule follows: for the same total volume of solvent, several extractions with small portions remove more compound than one extraction with the whole volume.

If the compound is only slightly more soluble in the organic solvent than in water, a very large volume of solvent would be needed. Then continuous extraction is used, where the same solvent is distilled and recycled through the solution again and again.

2.7 Choosing a method for liquids

SituationMethodExample
Boiling points far apart, no decompositionSimple distillationChloroform and aniline
Boiling points close togetherFractional distillationAcetone and methanol; crude oil
Liquid decomposes at or below its normal bpDistillation under reduced pressureGlycerol from spent lye
Steam volatile and immiscible with waterSteam distillationAniline from water; essential oils
Compound dissolved in water, more soluble in an immiscible solventDifferential extractionOrganic product from an aqueous reaction mixture

Worked example 2.1: Name the best method for: (i) a mixture of chloroform and aniline; (ii) acetone and methanol; (iii) glycerol from spent lye; (iv) aniline from an aniline–water mixture.

Solution: (i) Simple distillation, as the boiling points (334 K and 457 K) are far apart. (ii) Fractional distillation, as the boiling points (329 K and 338 K) are close. (iii) Distillation under reduced pressure, as glycerol decomposes at its boiling point. (iv) Steam distillation, as aniline is steam volatile and immiscible with water.

Worked example 2.2: In a distillation, a student places the thermometer bulb inside the boiling liquid. What goes wrong?

Solution: The thermometer reads the temperature of the liquid, which can be higher than that of the vapour leaving through the side arm, especially if the liquid is superheated. The student cannot tell when one component has finished distilling and the next has begun. The bulb belongs just at the level of the side arm.

Worked example 2.3: A mixture of water and an immiscible liquid B is steam distilled at 760 mm Hg and boils at 98 °C. The vapour pressure of water at 98 °C is 707 mm Hg. Find the vapour pressure of B at 98 °C.

Solution: p_total = p_water + p_B, so p_B = 760 − 707 = 53 mm Hg.

Worked example 2.4: In Example 2.3, B has molar mass 120 g/mol. What mass of B distils over with every 100 g of water?

Solution: m_B / m_water = (p_B × M_B) / (p_water × 18) = (53 × 120) / (707 × 18) = 6360 / 12726 = 0.50. So about 50 g of B comes over with every 100 g of water. B is only 53/760, about 7%, of the vapour by moles, but about one-third of the distillate by mass, because its molar mass is so much higher than that of water.

Worked example 2.5: 10 g of a compound is dissolved in 100 mL of water. Its distribution coefficient between ether and water is K_D = 4. How much is extracted by one shaking with 50 mL of ether?

Solution: Fraction left in water = 100 / (100 + 4 × 50) = 100/300 = 1/3. Mass left = 10/3 = 3.33 g. Mass extracted = 10 − 3.33 = 6.67 g.

Worked example 2.6: Repeat Example 2.5 using two portions of 25 mL of ether each.

Solution: Fraction left after each extraction = 100 / (100 + 4 × 25) = 1/2. After two: (1/2)² = 1/4. Mass left = 2.5 g. Mass extracted = 7.5 g. The same 50 mL of ether removes 7.5 g in two portions against 6.67 g in one.

Worked example 2.7: An aqueous solution is extracted (i) with diethyl ether and (ii) with chloroform. In each case, from which part of the separating funnel do you collect the organic layer?

Solution: (i) Ether is less dense than water, so it forms the upper layer. Run off the water through the tap, then pour the ether out from the top. (ii) Chloroform is denser than water, so it forms the lower layer and is run off through the tap.

Worked example 2.8: A mixture of o-nitrophenol and p-nitrophenol is steam distilled. Which isomer comes over, and why?

Solution: o-Nitrophenol distils over. Its –OH and –NO₂ groups are next to each other, so it forms an intramolecular hydrogen bond within one molecule. Its molecules do not hold each other strongly, so it is volatile. In p-nitrophenol the groups are far apart, so it forms intermolecular hydrogen bonds between molecules. These molecules associate, so its volatility is low and it stays in the flask.

Quick revision

  • A liquid boils when its vapour pressure equals the outside pressure. Lower pressure gives a lower boiling point.

  • Simple distillation: bp far apart (chloroform 334 K, aniline 457 K). Fractional: bp close (acetone 329 K, methanol 338 K; crude oil).

  • Fractionating column: repeated vaporisation and condensation on a large surface; the top vapour is rich in the lower-boiling liquid.

  • Reduced pressure: liquids that decompose at or below their normal bp; glycerol from spent lye.

  • Steam distillation: steam volatile and water-immiscible; p_total = p_water + p_organic, so boils below 373 K.

  • Steam distillate: m_org/m_water = p_org M_org / (p_water × 18).

  • Differential extraction: K_D = C_org/C_aq; several small extractions beat one large one.

  • Ether floats on water; chloroform sinks below it.

NEET traps

  • Saying steam distillation happens at 373 K. It happens below 373 K at 1 atm.

  • Writing the mass ratio in a steam distillate as equal to the vapour pressure ratio. That is the mole ratio; multiply by molar masses for mass.

  • Putting the thermometer bulb in the liquid, or letting condenser water enter from the top.

  • Choosing steam distillation for p-nitrophenol. Only the ortho isomer is steam volatile.

  • Assuming the organic layer is always on top. It depends on density: ether on top, chloroform at the bottom.

  • Thinking one large extraction is as good as several small ones of the same total volume.

Practice MCQs: Chapter 2

Level 1: Concept check

1. Simple distillation is suitable for separating liquids that (a) decompose below their boiling points (b) are immiscible with water and steam volatile (c) have boiling points very close together (d) have widely different boiling points and do not decompose

2. Crude petroleum is separated into its fractions by (a) steam distillation (b) sublimation (c) fractional distillation (d) differential extraction

3. Glycerol is recovered from spent lye in the soap industry by (a) steam distillation (b) simple distillation (c) distillation under reduced pressure (d) crystallisation

4. A liquid boils when its vapour pressure becomes equal to (a) the external pressure (b) half of the atmospheric pressure (c) the vapour pressure of water (d) zero

5. Aniline is separated from an aniline–water mixture by (a) steam distillation (b) sublimation (c) crystallisation (d) fractional crystallisation

6. The main job of a fractionating column is to provide (a) a cooling jacket for the vapour (b) a vacuum above the liquid (c) a drying agent for the vapour (d) a large surface for repeated vaporisation and condensation

7. Differential extraction is carried out in a (a) Kjeldahl flask (b) Carius tube (c) separating funnel (d) china dish

8. When the pressure above a liquid is reduced, its boiling point (a) rises (b) falls (c) stays the same (d) first rises and then falls

9. A mixture of chloroform (bp 334 K) and aniline (bp 457 K) is most simply separated by (a) steam distillation (b) simple distillation (c) sublimation (d) chromatography

10. At 1 atm, a mixture undergoing steam distillation boils (a) at exactly 373 K (b) above 373 K (c) at the boiling point of the organic liquid (d) below 373 K

Level 2: NEET standard

11. A liquid C, immiscible with water, is steam distilled at 760 mm Hg. The mixture boils at 95 °C, where the vapour pressure of water is 634 mm Hg. The vapour pressure of C at 95 °C is (a) 634 mm Hg (b) 760 mm Hg (c) 394 mm Hg (d) 126 mm Hg

12. In steam distillation, the ratio of moles of organic compound to moles of water in the distillate equals (a) the ratio of their molar masses (b) the ratio of their vapour pressures (c) the inverse ratio of their vapour pressures (d) one

13. o-Nitrophenol is steam volatile but p-nitrophenol is not, because (a) p-nitrophenol has intramolecular hydrogen bonding (b) o-nitrophenol has intramolecular hydrogen bonding while p-nitrophenol has intermolecular hydrogen bonding (c) o-nitrophenol is ionic (d) p-nitrophenol has a lower molar mass

14. A compound is extracted from water using diethyl ether in a separating funnel. The ether layer is (a) the upper layer, since ether is less dense than water (b) the lower layer, since ether is denser than water (c) mixed completely with water (d) the middle of three layers

15. In a distillation set-up, the thermometer bulb should be (a) dipped in the boiling liquid (b) placed at the top of the condenser (c) just at the level of the side arm of the flask (d) placed inside the receiver

16. For the same total volume of solvent, extraction in several small portions compared with one large portion is (a) less efficient (b) more efficient (c) equally efficient (d) efficient only for acids

17. Cooling water enters a water condenser at its lower end because (a) gravity helps the water flow faster (b) the jacket stays completely full and the counter-flow cools the vapour best (c) it prevents bumping in the flask (d) it lowers the pressure in the flask

18. A substance purified by steam distillation must be (a) miscible with water and non-volatile (b) soluble in water and decomposed by steam (c) immiscible with water and volatile in steam (d) ionic and high melting

19. Acetone (bp 329 K) and methanol (bp 338 K) are best separated by (a) simple distillation (b) steam distillation (c) fractional distillation (d) sublimation

20. Porous porcelain pieces are added to the distillation flask to (a) catalyse the distillation (b) adsorb coloured impurities (c) raise the boiling point (d) give smooth boiling and prevent bumping

21. A liquid that decomposes at its normal boiling point is best purified by (a) distillation under reduced pressure (b) simple distillation (c) fractional distillation (d) sublimation

22. For a solute shared between ether and water, K_D = C_ether / C_water = 5. This means that at equilibrium (a) the solute is five times more soluble in water (b) its concentration in ether is five times that in water (c) five extractions are needed (d) ether is five times denser than water

Level 3: Challenge

23. The liquid C of Q11 has molar mass 150 g/mol. The mass of C that distils over with every 100 g of water is closest to (a) 166 g (b) 19.9 g (c) 60 g (d) 100 g

24. 9 g of a compound is dissolved in 60 mL of water. K_D (solvent/water) = 3. The mass extracted by one shaking with 60 mL of the solvent is (a) 3 g (b) 4.5 g (c) 2.25 g (d) 6.75 g

25. In Q24, if the 60 mL of solvent is used as two portions of 30 mL each, the total mass extracted is (a) 6.75 g (b) 7.2 g (c) 8.1 g (d) 7.56 g

26. During fractional distillation of a mixture of two miscible liquids, the vapour reaching the top of the column is richer in (a) the higher-boiling liquid (b) the lower-boiling liquid (c) both liquids equally (d) water vapour

27. A crude sample of an amine is immiscible with water, steam volatile, partly decomposes near its normal boiling point, and contains a non-volatile tarry impurity. The most suitable method among these is (a) simple distillation at 1 atm (b) fractional crystallisation (c) sublimation (d) steam distillation

28. Which statement about steam distillation is incorrect? (a) The total vapour pressure is the sum of the vapour pressures of water and the organic liquid (b) The mixture boils below 373 K at 1 atm (c) The mole ratio in the distillate equals the ratio of the molar masses of the two liquids (d) The organic compound must be immiscible with water

29. Assertion (A): Glycerol is purified by distillation under reduced pressure. Reason (R): Glycerol decomposes at its normal boiling point, and lowering the pressure lowers the boiling point. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: In steam distillation, the organic liquid distils at a temperature below its own normal boiling point. Statement II: A fractionating column allows repeated vaporisation and condensation of the rising vapour. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1dSimple distillation needs a large bp gap and no decomposition.
2cCrude oil fractions have close, overlapping boiling ranges.
3cGlycerol decomposes at its normal bp.
4aBoiling point definition.
5aAniline is steam volatile and immiscible with water.
6dThe packing gives many condense-and-boil steps.
7cTwo immiscible layers are separated in a separating funnel.
8bLess outside pressure is reached at a lower temperature.
9b334 K and 457 K are far apart.
10dp_water + p_org reaches 760 mm Hg before water alone would.
11d760 − 634 = 126 mm Hg.
12bMole ratio in vapour = partial pressure ratio.
13bIntramolecular H-bond in ortho keeps molecules unassociated.
14aEther (0.71 g/mL) floats on water.
15cIt must read the temperature of the vapour leaving.
16bFraction left multiplies down with each extraction.
17bBottom entry keeps the jacket full; counter-current cooling.
18cBoth conditions are needed for steam distillation.
19cA 9 K gap needs a fractionating column.
20dPorcelain pieces give steady small bubbles.
21aLower pressure lets it boil below its decomposition temperature.
22bK_D is the ratio of concentrations, organic over aqueous.
23am_C/m_w = 126 × 150 / (634 × 18) = 1.656; about 166 g.
24dLeft = 9 × 60/(60 + 180) = 2.25 g; extracted 6.75 g.
25dLeft = 9 × (60/150)² = 1.44 g; extracted 7.56 g.
26bEach plate enriches the vapour in the more volatile liquid.
27dSteam distillation works below 373 K, away from decomposition.
28cMole ratio equals the vapour pressure ratio, not molar mass ratio.
29aR is the exact reason for using low pressure.
30aBoth are correct descriptions.

Chapter 2 revision sheet

One-page summary

  • A liquid boils when its vapour pressure equals the outside pressure; lower outside pressure, lower boiling point.

  • Simple distillation: volatile liquid from non-volatile impurity, or two liquids with widely different boiling points (chloroform 334 K and aniline 457 K).

  • Fractional distillation: boiling points close together (acetone 329 K and methanol 338 K); used for crude oil fractions.

  • Fractionating column gives a large surface for repeated vaporisation and condensation; the top is richest in the lower-boiling liquid.

  • Reduced-pressure (vacuum) distillation: liquids that decompose at or below their normal boiling point; glycerol from spent lye in soap making.

  • Steam distillation: steam-volatile, water-immiscible substances (aniline, o-nitrophenol, essential oils, turpentine).

  • In steam distillation p_water + p_organic = outside pressure, so the mixture boils below 373 K at 1 atm.

  • Distillate mass ratio: m_org / m_water = (p_org × M_org) / (p_water × 18).

  • o-Nitrophenol (intramolecular H-bond) is steam volatile; p-nitrophenol (intermolecular H-bond) is not.

  • Differential extraction: shake the aqueous solution with an immiscible organic solvent in which the compound dissolves better.

  • K_D = C_org / C_aq at a fixed temperature.

  • Several small extractions remove more than one big extraction with the same total volume.

  • Ether (less dense) forms the upper layer; chloroform (denser) forms the lower layer.

Must-remember table

MethodUse whenClassic example
Simple distillationbp differ widelyChloroform (334 K) + aniline (457 K)
Fractional distillationbp closeAcetone (329 K) + methanol (338 K); crude oil
Reduced pressureDecomposes at normal bpGlycerol from spent lye
Steam distillationSteam volatile, immiscible with waterAniline, o-nitrophenol, essential oils
Differential extractionMore soluble in organic solventOrganic compound from water using ether
Steam distillate ratiom_org/m_water = p_org M_org/(p_water × 18)M_water = 18 g/mol
Mass left after n extractionsx_n = W [V_aq/(V_aq + K_D V_org)]^nV_org = volume per portion

Memory aids

  • "Far is Simple, Few is Fractional": far-apart boiling points need simple distillation; a few kelvin apart need fractional.

  • "GLR = Glycerol, Lye, Reduced": glycerol from spent lye is the reduced-pressure example.

  • "A NOTE on steam": Aniline, o-Nitrophenol, Oils (essential), Turpentine, Eucalyptus-type plant oils are steam distilled.

  • "Ether Up, Chloroform Cellar": ether floats on water, chloroform sinks to the bottom.

  • "Little and often": several small extractions beat one big one.

Concept connections

  • Vapour pressure and Raoult's law: Chemistry Book 5: Solutions.

  • Intramolecular H-bonding in o-nitrophenol: Chemistry Book 3: Chemical Bonding and Molecular Structure.

  • Distribution law and constant K_D: Chemistry Book 6: Equilibrium.

Practice MCQs: Chapter 2, Level 4 (new NEET pattern)

31. Match List I (mixture) with List II (method).

List IList II
(A) Chloroform + aniline(i) Steam distillation
(B) Acetone + methanol(ii) Reduced-pressure distillation
(C) Glycerol from spent lye(iii) Simple distillation
(D) Aniline from a water mixture(iv) Fractional distillation

(a) A-iv, B-iii, C-ii, D-i (b) A-iii, B-iv, C-ii, D-i (c) A-iii, B-iv, C-i, D-ii (d) A-ii, B-iv, C-iii, D-i

32. Match List I (apparatus part) with List II (job).

List IList II
(A) Fractionating column(i) Turns vapour back into liquid
(B) Condenser(ii) Separates two immiscible layers
(C) Porous pot pieces(iii) Large surface for repeated vaporisation and condensation
(D) Separating funnel(iv) Smooth boiling, no bumping

(a) A-i, B-iii, C-iv, D-ii (b) A-iii, B-iv, C-i, D-ii (c) A-iii, B-i, C-ii, D-iv (d) A-iii, B-i, C-iv, D-ii

33. Match List I (substance) with List II (property used in purification).

List IList II
(A) Glycerol(i) Steam volatile because of intramolecular H-bonding
(B) o-Nitrophenol(ii) Less dense than water; upper layer
(C) Diethyl ether(iii) Denser than water; lower layer
(D) Chloroform(iv) Decomposes near its normal boiling point

(a) A-iv, B-i, C-ii, D-iii (b) A-i, B-iv, C-ii, D-iii (c) A-iv, B-i, C-iii, D-ii (d) A-ii, B-i, C-iv, D-iii

34. Match List I (process) with List II (principle).

List IList II
(A) Simple distillation(i) Different solubility in two immiscible solvents
(B) Steam distillation(ii) Large difference in boiling points
(C) Differential extraction(iii) Lower outside pressure lowers the boiling point
(D) Reduced-pressure distillation(iv) Sum of two vapour pressures equals outside pressure

(a) A-iv, B-ii, C-i, D-iii (b) A-ii, B-iv, C-iii, D-i (c) A-ii, B-iv, C-i, D-iii (d) A-i, B-iv, C-ii, D-iii

35. How many of the following statements are correct?

  • A. In steam distillation the mixture boils below 373 K at 1 atm.

  • B. Steam distillation suits substances that mix completely with water.

  • C. Crude oil is separated into fractions by fractional distillation.

  • D. Vapour at the top of a fractionating column is richer in the lower-boiling component.

(a) One (b) Two (c) Three (d) Four

36. Choose the correct set of statements.

  • A. Lowering the outside pressure lowers the boiling point of a liquid.

  • B. Several extractions with small volumes remove more solute than one extraction with the same total volume.

  • C. Chloroform forms the upper layer when shaken with water.

  • D. Aniline is separated from water by fractional distillation.

(a) A and B only (b) A, B and C only (c) B and D only (d) A, B and D only

37. How many of the following statements are correct?

  • A. Simple distillation cleanly separates acetone (329 K) from methanol (338 K).

  • B. Glycerol is distilled under reduced pressure because it decomposes near its normal boiling point.

  • C. Essential oils are commonly isolated by steam distillation.

  • D. In differential extraction the organic solvent must be immiscible with water.

(a) Four (b) Two (c) One (d) Three

38. Choose the correct set of statements.

  • A. At the steam-distillation temperature, the organic liquid alone has a vapour pressure of 760 mm.

  • B. p-Nitrophenol, with intermolecular H-bonding, is less steam volatile than o-nitrophenol.

  • C. A compound with low vapour pressure but high molar mass can still give a good mass in the steam distillate.

  • D. Porous pot pieces are best added after the liquid starts boiling.

(a) A and B only (b) B and C only (c) C and D only (d) A, B and C only

39. Data table at 368 K: vapour pressure of water 634 mm, of aniline (M = 93 g/mol) 126 mm; outside pressure 760 mm. The mass ratio aniline : water in the steam distillate is about: (a) 1.03 (b) 0.20 (c) 5.17 (d) 0.97

40. For a solute, K_D (ether/water) = 4. 10 g of it is dissolved in 100 mL water. Mass left in water after (i) one extraction with 100 mL ether and (ii) two extractions with 50 mL ether each: (a) 2.5 g and 1.25 g (b) 2.0 g and 2.0 g (c) 2.0 g and 1.11 g (d) 8.0 g and 8.89 g

41. A graph of temperature at the top of a fractionating column against volume distilled, for an acetone–methanol mixture, stays near 329 K for the first 40 mL, rises sharply, then becomes flat near 338 K. The flat part near 338 K shows that: (a) Acetone is distilling (b) The mixture boils as one constant-boiling liquid (c) The thermometer bulb is placed wrongly (d) Nearly pure methanol is distilling

Passage for Q42–43: An essential oil (M = 150 g/mol), immiscible with water, is steam distilled at 1 atm (760 mm). At the temperature where the mixture boils, the vapour pressure of water is 700 mm.

42. The vapour pressure of the oil at this temperature is: (a) 700 mm (b) 60 mm (c) 760 mm (d) 30 mm

43. Mass of oil that distils over with every 100 g of water is about: (a) 71.4 g (b) 8.6 g (c) 14.0 g (d) 46.7 g

44. o-Nitrophenol can be separated from p-nitrophenol by steam distillation because: (a) The ortho isomer has the higher molar mass (b) The para isomer is a stronger acid, and acids are never steam volatile (c) The ortho isomer has intramolecular H-bonding, so it is more volatile and less soluble in water (d) The para isomer decomposes in steam

45. 1.0 g of a solute is in 90 mL water. K_D (chloroform/water) = 9. Mass extracted by three successive 10 mL portions of chloroform is: (a) 0.750 g (b) 0.125 g (c) 0.667 g (d) 0.875 g

Level 4 answer key

QAnsReason
31bFar bp, close bp, decomposes, steam volatile
32dColumn, condenser, boiling chips, separating funnel
33aGlycerol decomposes; o-nitrophenol volatile; ether up; chloroform down
34cEach method matched to its principle
35cA, C, D true; steam distillation needs immiscible liquids
36aChloroform sinks; aniline is steam distilled
37dB, C, D true; close bp needs fractional distillation
38bp_org is only part of 760 mm; chips go in before heating
39a(126 × 93)/(634 × 18) = 1.03
40c10 × 100/500 = 2.0 g; 10 × (100/300)² = 1.11 g
41dSecond plateau is the higher-boiling methanol
42b760 − 700 = 60 mm
43a100 × (60 × 150)/(700 × 18) = 71.4 g
44cIntramolecular H-bond means weaker attraction to neighbours and to water
45dLeft = (90/180)³ = 0.125 g; extracted 0.875 g
27 min left
‹
›