Chapter 11 of 12 · 11 min read

Unit Test: Properties of Solids and Liquids

Time: 50 minutes. Marking: +4 for a correct answer, −1 for a wrong one, 0 if left blank. Take g = 10 m/s² unless stated. The questions are mixed across all eight chapters.

1. A steel wire 2 m long and 0.5 mm in radius carries a load of 31.4 N. Y = 2 × 10¹¹ Pa. Its extension is (a) 0.4 mm (b) 0.2 mm (c) 0.8 mm (d) 4 mm

2. On a stress-strain curve, the point beyond which a wire takes a permanent set is the (a) fracture point (b) elastic limit (c) ultimate stress point (d) origin

3. A force of 60 N stretches a wire by 3 mm within the elastic limit. The elastic energy stored is (a) 0.18 J (b) 0.045 J (c) 0.09 J (d) 0.9 J

4. An ideal gas at a pressure of 2 × 10⁵ Pa is compressed slowly at constant temperature. Its bulk modulus is (a) 1 × 10⁵ Pa (b) 4 × 10⁵ Pa (c) 1.4 × 10⁵ Pa (d) 2 × 10⁵ Pa

5. Wires A and B are of the same material. Their lengths are in the ratio 1 : 2 and diameters in the ratio 2 : 1. Under equal loads, the ratio of extensions A : B is (a) 1 : 8 (b) 8 : 1 (c) 1 : 2 (d) 1 : 4

6. The gauge pressure at a depth of 4 m in a liquid of relative density 1.5 is (a) 4 × 10⁴ Pa (b) 6 × 10⁴ Pa (c) 6 × 10³ Pa (d) 1.6 × 10⁵ Pa

7. The pistons of a hydraulic lift have diameters 4 cm and 40 cm. A force of 50 N on the small piston can support a load of (a) 500 N (b) 50 000 N (c) 5000 N (d) 50 N

8. A body floats in a liquid with 40% of its volume above the surface. The ratio of its density to the liquid's density is (a) 0.4 (b) 1.67 (c) 2.5 (d) 0.6

9. A metal piece of relative density 4 weighs 60 N in air. Fully immersed in water it weighs (a) 45 N (b) 15 N (c) 40 N (d) 56 N

10. A barometer at a hill station reads 70 cm of mercury (ρ = 13 600 kg/m³). The atmospheric pressure there is (a) 1.01 × 10⁵ Pa (b) 9.52 × 10³ Pa (c) 9.52 × 10⁴ Pa (d) 7.0 × 10⁴ Pa

11. Water flows at 1.5 m/s in a pipe of diameter 6 cm, which narrows to 3 cm. The speed in the narrow part is (a) 3 m/s (b) 6 m/s (c) 0.75 m/s (d) 12 m/s

12. Water leaks from a small hole 1.8 m below the surface in an open tank. The speed of efflux is (a) 3 m/s (b) 36 m/s (c) 6 m/s (d) 18 m/s

13. Water enters a horizontal pipe at 2 m/s. At a narrower section the pressure is 6000 Pa lower. The speed there is (a) 4 m/s (b) 6 m/s (c) 8 m/s (d) 3.5 m/s

14. Water stands 6 m high in a tank on the ground. A small hole is 4 m below the surface. The jet strikes the ground at a horizontal distance of about (a) 4 m (b) 5.66 m (c) 6 m (d) 8 m

15. Which of these does not work on Bernoulli's principle? (a) Perfume atomiser (b) Aeroplane lift (c) Hydraulic brakes (d) Venturimeter

16. Two rain drops have radii in the ratio 2 : 3. The ratio of their terminal velocities is (a) 2 : 3 (b) 8 : 27 (c) 3 : 2 (d) 4 : 9

17. 64 identical drops, each falling at a terminal velocity of 2 cm/s, merge into one drop. Its terminal velocity is (a) 32 cm/s (b) 8 cm/s (c) 128 cm/s (d) 16 cm/s

18. Blood (ρ = 1050 kg/m³, η = 3 × 10⁻³ Pa s) flows at 0.1 m/s in a vessel of diameter 2 cm. The Reynolds number and the type of flow are (a) 70, streamline (b) 700, streamline (c) 7000, turbulent (d) 700, turbulent

19. A plate of area 0.5 m² slides at 0.4 m/s over an oil film 2 mm thick (η = 0.2 Pa s). The viscous force is (a) 2 N (b) 40 N (c) 20 N (d) 10 N

20. A ball falls through a liquid at terminal velocity. Then (a) viscous force = weight (b) viscous force + buoyant force = weight (c) buoyant force = weight (d) viscous force = 0

21. The excess pressure inside a soap bubble of radius 5 mm (S = 0.025 N/m) is (a) 10 Pa (b) 40 Pa (c) 5 Pa (d) 20 Pa

22. Water (S = 0.072 N/m, θ = 0°) rises in a glass capillary of radius 0.3 mm to a height of (a) 4.8 cm (b) 2.4 cm (c) 9.6 cm (d) 0.48 cm

23. A soap bubble (S = 0.03 N/m) is blown up from radius 1 cm to 2 cm. The work done is about (a) 7.5 × 10⁻⁵ J (b) 1.1 × 10⁻⁴ J (c) 2.3 × 10⁻⁴ J (d) 3.0 × 10⁻⁴ J

24. A liquid wets a solid surface when the angle of contact is (a) obtuse (b) acute (c) exactly 90° (d) 180°

25. The same clean capillary is dipped in water and in a liquid X of relative density 0.8 with the same surface tension and zero contact angle. The ratio of rise h_X : h_water is (a) 0.8 (b) 1 (c) 1.6 (d) 1.25

26. A temperature of 25 °C on the Fahrenheit scale is (a) 45 °F (b) 57 °F (c) 77 °F (d) 87 °F

27. A rod 50 cm long (α = 2 × 10⁻⁵ K⁻¹) is heated by 80 °C. It lengthens by (a) 0.8 mm (b) 0.4 mm (c) 1.6 mm (d) 8 mm

28. A metal has a coefficient of volume expansion of 6 × 10⁻⁵ K⁻¹. Its coefficient of area expansion is (a) 2 × 10⁻⁵ K⁻¹ (b) 3 × 10⁻⁵ K⁻¹ (c) 1.2 × 10⁻⁴ K⁻¹ (d) 4 × 10⁻⁵ K⁻¹

29. A rod (Y = 1.2 × 10¹¹ Pa, α = 1.5 × 10⁻⁵ K⁻¹) is held between rigid supports and heated by 40 °C. The thermal stress is (a) 3.6 × 10⁷ Pa (b) 7.2 × 10⁷ Pa (c) 1.44 × 10⁸ Pa (d) 7.2 × 10⁶ Pa

30. A pendulum clock loses 12 s a day when the temperature rises by 10 °C. The coefficient of linear expansion of its rod is about (a) 2.8 × 10⁻⁵ K⁻¹ (b) 1.4 × 10⁻⁵ K⁻¹ (c) 5.6 × 10⁻⁵ K⁻¹ (d) 1.2 × 10⁻⁵ K⁻¹

31. 300 g of water at 70 °C is mixed with 200 g of water at 20 °C. The final temperature is (a) 45 °C (b) 40 °C (c) 50 °C (d) 55 °C

32. The heat needed to turn 2 g of ice at 0 °C into water at 100 °C is (a) 160 cal (b) 200 cal (c) 1440 cal (d) 360 cal

33. 40 g of ice at 0 °C is dropped into 160 g of water at 50 °C. The final temperature is (a) 0 °C (b) 24 °C (c) 20 °C (d) 30 °C

34. The heat capacity of a 0.5 kg aluminium block (c = 900 J/(kg K)) is (a) 450 J/K (b) 900 J/K (c) 1800 J/K (d) 225 J/K

35. A 2 kW kettle holds 1 kg of water already at 100 °C. Taking L_v = 2.26 × 10⁶ J/kg and no losses, the time to boil it all away is about (a) 9.4 min (b) 37.7 min (c) 3.8 min (d) 18.8 min

36. A rod (k = 200 W/(m K)) 0.5 m long with area 4 cm² has a temperature difference of 50 °C between its ends. The heat current is (a) 4 W (b) 16 W (c) 8 W (d) 80 W

37. By what factor must the absolute temperature of a black body rise for its radiated power to become 81 times? (a) 3 (b) 9 (c) 27 (d) 4.5

38. A black body's spectrum peaks at 1.45 μm. Its temperature is (a) 1000 K (b) 2000 K (c) 4000 K (d) 2900 K

39. A body cools from 60 °C to 50 °C in 4 minutes in a room at 20 °C. Using the average form of Newton's law, the time to cool from 50 °C to 40 °C is about (a) 4 min (b) 6.4 min (c) 7 min (d) 5.6 min

40. Two slabs of equal thickness and area, with k = 60 and 20 W/(m K), are in series. The free face of the first is at 100 °C and that of the second at 0 °C. The interface temperature is (a) 25 °C (b) 50 °C (c) 75 °C (d) 66.7 °C

41. Which of these quantities is dimensionless? (a) Surface tension (b) Reynolds number (c) Coefficient of viscosity (d) Young's modulus

42. While a raindrop falls at its terminal velocity, the work done on it by gravity mainly becomes (a) kinetic energy of the drop (b) gravitational potential energy (c) surface energy (d) heat, through viscous drag

43. Assertion (A): A small soap bubble has a higher excess pressure inside than a large one. Reason (R): The excess pressure inside a bubble is inversely proportional to its radius. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

44. Assertion (A): Mercury rises in a glass capillary tube. Reason (R): Mercury does not wet glass. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

45. Statement I: Bernoulli's principle is a form of the law of conservation of energy. Statement II: As the temperature of a black body rises, its wavelength of peak emission increases. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key: Unit Test

QAnsReason
1aΔL = 31.4 × 2/(π × 0.25×10⁻⁶ × 2×10¹¹) = 0.4 mm
2bBeyond the elastic limit, recovery is incomplete
3c½ × 60 × 0.003 = 0.09 J
4dIsothermal B equals the pressure
5aΔL ∝ L/d²: (1/2) × (1/4) = 1/8
6b1500 × 10 × 4 = 6 × 10⁴ Pa
7cArea ratio (40/4)² = 100
8d60% submerged gives 0.6
9aBuoyancy = 60/4 = 15 N; 60 − 15 = 45 N
10c0.70 × 13 600 × 10 = 9.52 × 10⁴ Pa
11bv ∝ 1/d²: 1.5 × 4 = 6 m/s
12c√(2 × 10 × 1.8) = 6 m/s
13a6000 = 500(v² − 4), v = 4 m/s
14b2√(4 × 2) ≈ 5.66 m
15cHydraulic brakes use Pascal's law
16dv ∝ r²
17a64^(2/3) = 16; 16 × 2 = 32 cm/s
18b1050 × 0.1 × 0.02/0.003 = 700, below 1000
19c0.2 × 0.5 × 0.4/0.002 = 20 N
20bNet force is zero
21d4 × 0.025/0.005 = 20 Pa
22a2 × 0.072/(3×10⁻⁴ × 10⁴) = 0.048 m
23c8πS(R₂² − R₁²) = 8π × 0.03 × 3×10⁻⁴
24bAcute angle means adhesion wins
25dh ∝ 1/ρ: 1/0.8 = 1.25
26c9 × 25/5 + 32 = 77
27a0.5 × 2×10⁻⁵ × 80 = 8×10⁻⁴ m
28dα = 2×10⁻⁵, β = 2α
29b1.2×10¹¹ × 1.5×10⁻⁵ × 40
30a12/86 400 = ½α × 10, α ≈ 2.8×10⁻⁵
31c(21 000 + 4000)/500 = 50 °C
32d2 × 80 + 2 × 100 = 360 cal
33bAll melts; 160(50 − T) = 3200 + 40T, T = 24 °C
34aC = mc = 0.5 × 900
35d2.26×10⁶/2000 = 1130 s ≈ 18.8 min
36c200 × 4×10⁻⁴ × 50/0.5 = 8 W
37aT⁴ factor 81 means T factor 3
38b2.9×10⁻³/1.45×10⁻⁶ = 2000 K
39dk = 2.5/35 per min; 10/t = k × 25, t = 5.6 min
40c60(100 − T) = 20T, T = 75 °C
41bρvD/η has no dimensions
42dKE is constant; energy goes to heat
43aΔP = 4S/R, so R explains A
44dMercury is depressed; R is true
45cλ_m falls as T rises (Wien)
11 min left
‹
›