Chapter 3 of 12 · 28 min read

Chapter 1: Elasticity

What you will learn

  • What stress and strain are, and the three kinds of each.

  • Hooke's law and how to read a stress-strain curve.

  • Young's modulus, bulk modulus and modulus of rigidity, with typical values.

  • Poisson's ratio in brief.

  • Elastic potential energy stored in a stretched wire, and energy density.

  • Standard NEET results: extension of a wire under its own weight, ratio problems, combined wires.

1.1 Elastic and plastic behaviour

Pull a rubber band and let go. It returns to its old length. Press a lump of wet clay and it keeps the dent. The rubber band is showing elasticity: the property of a body to regain its original size and shape when the deforming force is removed. The clay is showing plasticity: it stays deformed.

Why does a solid spring back? Think of its atoms as balls joined by tiny springs (the interatomic forces). Pull the solid, and the springs stretch. Each spring pulls back. Remove the force and the springs restore the original spacing.

No real body is perfectly elastic or perfectly plastic. Quartz fibre comes close to perfectly elastic. Putty and wax come close to perfectly plastic. Note one surprise: in physics, steel is more elastic than rubber. Elastic means "hard to deform and comes back", not "easy to stretch". You will see this through Young's modulus.

1.2 Stress

When a force deforms a body, the body develops an internal restoring force. Stress is this restoring force per unit area. In equilibrium, it equals the applied force divided by the area.

Stress=FA\text{Stress} = \frac{F}{A}

SI unit: N/m² or pascal (Pa). Dimensions: [M L⁻¹ T⁻²], the same as pressure.

There are three kinds of stress:

Kind of stressDirection of forceEffect on the bodyExample
Longitudinal (tensile or compressive)Normal to the area, along the lengthLength changesCable of a lift, pillar of a building
Shearing (tangential)Parallel to the areaShape changes, volume staysPushing the top of a thick book sideways
Hydraulic (volume)Normal to every face, equal from all sidesVolume changes, shape staysSteel ball deep in the sea

1.3 Strain

Strain is the fractional change in size or shape. It is a ratio, so it has no unit and no dimensions.

  • Longitudinal strain = change in length / original length = ΔL/L.

  • Volume strain = change in volume / original volume = ΔV/V.

  • Shear strain = the angle θ (in radians) through which a vertical line in the body turns. If the top face of height L shifts sideways by Δx, then tan θ = Δx/L, and for small angles θ ≈ Δx/L.

1.4 Hooke's law and the stress-strain curve

Hooke's law: for small deformations, stress is directly proportional to strain.

Stress=E×Strain\text{Stress} = E \times \text{Strain}

The constant E is called the modulus of elasticity. It depends only on the material (and temperature), not on the length or thickness of the sample.

Now load a ductile metal wire slowly until it breaks. Plot stress (y-axis) against strain (x-axis). You get the curve in Figure 1.1. Read it in stages:

  1. O to A, proportional limit. The graph is a straight line. Hooke's law holds. The slope is Young's modulus.

  2. A to B, elastic limit (yield point). Stress is no longer proportional to strain, but the wire still returns to its original length when unloaded. The stress at B is the yield strength.

  3. B to D, plastic region. Beyond B the wire does not fully recover. Unload it at C and it comes back along a line parallel to OA, keeping a permanent set (permanent strain).

  4. D, ultimate tensile strength. The highest stress the wire can bear. After D the wire starts to thin at one spot (necking).

  5. E, fracture point. The wire breaks.

Figure 1.1 · Stress-strain curve of a ductile metal
Figure 1.1 · Stress-strain curve of a ductile metal

The straight part OA obeys Hooke's law; unloading from C follows a line parallel to OA and leaves a permanent strain.

How to use the curve:

  • If D and E are far apart, the material is ductile (copper, aluminium, mild steel). It can be drawn into wires.

  • If D and E are close, the material is brittle (glass, cast iron). It breaks soon after the elastic limit.

  • Rubber and the elastic tissue of the aorta are elastomers. They stretch to many times their length and return, but their curve is not a straight line. They have no clear proportional region.

1.5 Young's modulus

For longitudinal stress and strain, the modulus is Young's modulus (Y).

Y=F/AΔL/L=FLA ΔLY = \frac{F/A}{\Delta L/L} = \frac{F L}{A\,\Delta L}

Rearranged, the extension of a wire is:

ΔL=FLAY=FLπr2Y\Delta L = \frac{F L}{A Y} = \frac{F L}{\pi r^2 Y}

This single line answers most NEET ratio questions. Extension grows with load and length, and falls with the square of the radius.

A second meaning of Y: if Hooke's law held all the way, the stress needed to double the length (strain = 1) would equal Y. Real wires break long before that.

On a stress-strain graph, Y is the slope of the straight part. A steeper line means a stiffer material.

Extension of a wire under its own weight. A uniform wire of length L, area A and density ρ hangs from a ceiling. Different parts carry different loads. The bottom carries nothing; the top carries the whole weight.

Take a thin slice of length dx at height x above the lower end. The part below it has weight ρAgx. This is the tension at that slice. Its extension is:

d(ΔL)=(ρAgx) dxAY=ρgx dxYd(\Delta L) = \frac{(\rho A g x)\,dx}{A Y} = \frac{\rho g x\,dx}{Y}

Add up from x = 0 to x = L:

ΔL=ρgY∫0Lx dx=ρgL22Y=MgL2AY\Delta L = \frac{\rho g}{Y}\int_0^L x\,dx = \frac{\rho g L^2}{2Y} = \frac{M g L}{2 A Y}

So a wire stretches under its own weight by half of what it would stretch if its whole weight hung at the end. The largest stress is at the top, equal to ρgL.

1.6 Bulk modulus

When pressure on all sides rises by p (= ΔP), the volume falls by ΔV. The bulk modulus (B) is:

B=−ΔPΔV/VB = -\frac{\Delta P}{\Delta V / V}

The minus sign keeps B positive, because volume decreases when pressure increases. The reciprocal of B is compressibility, K = 1/B. Gases are highly compressible (small B); solids are least compressible.

Bulk modulus is the only modulus that solids, liquids and gases all have. Liquids and gases cannot hold a fixed shape, so they have no Young's modulus or rigidity modulus.

Two useful results:

  • For a sphere, V ∝ r³, so ΔV/V = 3 Δr/r. Under pressure p, the fractional fall in radius is p/(3B).

  • Density rises as volume falls: Δρ/ρ ≈ p/B for small changes.

1.7 Modulus of rigidity (shear modulus)

Fix the bottom of a block and push its top face sideways with force F. The block leans by a small angle θ. The modulus of rigidity (G), also called shear modulus, is:

G=F/Aθ=FA θG = \frac{F/A}{\theta} = \frac{F}{A\,\theta}

Here A is the area of the face on which F acts (the top face), not the side face. For most solids G is roughly one third of Y.

ModulusStress usedStrain usedExists forTypical value for steel
Young's modulus YLongitudinal F/AΔL/LSolids onlyabout 2.0 × 10¹¹ Pa
Bulk modulus BPressure change ΔP−ΔV/VSolids, liquids, gasesabout 1.6 × 10¹¹ Pa
Rigidity modulus GTangential F/AAngle θSolids onlyabout 8 × 10¹⁰ Pa

Some approximate values of Y: steel 2.0 × 10¹¹ Pa, copper 1.1 to 1.2 × 10¹¹ Pa, aluminium 7.0 × 10¹⁰ Pa, glass about 6.5 × 10¹⁰ Pa, rubber only about 10⁷ Pa. Bulk modulus of water is about 2.2 × 10⁹ Pa.

1.8 Poisson's ratio (brief)

Stretch a rubber tube and it gets thinner. Any wire does the same, just much less. The ratio of lateral strain to longitudinal strain is Poisson's ratio (σ).

σ=lateral strainlongitudinal strain=Δd/dΔL/L\sigma = \frac{\text{lateral strain}}{\text{longitudinal strain}} = \frac{\Delta d / d}{\Delta L / L}

(Taken as a positive number, since one strain is an increase and the other a decrease.)

  • It has no unit.

  • Theory allows −1 < σ < 0.5. For real materials it lies between 0 and 0.5; metals are near 0.3.

  • If σ = 0.5, the volume of the wire does not change on stretching. Rubber is close to this.

For reference, the moduli are linked by Y = 2G(1 + σ) and Y = 3B(1 − 2σ).

1.9 Elastic potential energy

Work done to stretch a wire is stored as elastic potential energy. Let the wire stretch slowly from 0 to l. At extension x, the force is F(x) = YAx/L. The work done is:

W=∫0lYAL x dx=12 YAL l2=12 F lW = \int_0^{l} \frac{Y A}{L}\,x\,dx = \frac{1}{2}\,\frac{Y A}{L}\,l^2 = \frac{1}{2}\,F\,l

Here F is the final load. So the energy stored is U = ½ × load × extension. The half appears because the force grows from zero.

Divide by the volume AL to get energy density:

u=12 stress×strain=12 Y (strain)2=(stress)22Yu = \frac{1}{2}\,\text{stress} \times \text{strain} = \frac{1}{2}\,Y\,(\text{strain})^2 = \frac{(\text{stress})^2}{2Y}

For a fixed load, U = F²L/(2AY). Thinner wires store more energy for the same load.

Everyday design uses these ideas. A crane rope is chosen so that the working stress is well below the yield strength. Beams are made I-shaped so that most material sits where bending stress is largest. Mountains cannot be taller than about 10 km on Earth because the stress at the base would exceed what rock can bear.

Worked example 1.1: A steel wire 2 m long with cross-sectional area 1 mm² carries a 10 kg load. Y = 2 × 10¹¹ Pa. Find the extension.

Solution: F = 10 × 10 = 100 N, A = 1 × 10⁻⁶ m². ΔL = FL/(AY) = (100 × 2)/(10⁻⁶ × 2 × 10¹¹) = 1 × 10⁻³ m = 1 mm.

Worked example 1.2: A stress of 1 × 10⁸ Pa stretches a 1 m wire by 0.5 mm. Find Young's modulus.

Solution: Strain = 0.5 × 10⁻³ / 1 = 5 × 10⁻⁴. Y = stress/strain = 10⁸ / (5 × 10⁻⁴) = 2 × 10¹¹ Pa.

Worked example 1.3: Two wires of the same metal carry equal loads. Wire P is twice as long as wire Q, but has half its diameter. Find the ratio of their extensions.

Solution: ΔL ∝ L/d² for the same F and Y. ΔL_P/ΔL_Q = (L_P/L_Q) × (d_Q/d_P)² = 2 × 2² = 8. Wire P stretches 8 times as much.

Worked example 1.4: Water has B = 2.2 × 10⁹ Pa. By what percentage does its volume fall when the pressure rises by 1.0 × 10⁷ Pa (about 100 atm)?

Solution: ΔV/V = ΔP/B = 10⁷ / (2.2 × 10⁹) = 4.5 × 10⁻³. That is about 0.45%. Water is nearly incompressible, which is why hydraulic machines work.

Worked example 1.5: An aluminium cube of side 10 cm has its bottom fixed. A tangential force of 1.0 × 10⁴ N acts on the top face. G = 2.5 × 10¹⁰ Pa. Find the sideways shift of the top face.

Solution: A = 0.1 × 0.1 = 0.01 m². θ = F/(AG) = 10⁴ / (0.01 × 2.5 × 10¹⁰) = 4 × 10⁻⁵ rad. Shift = θ × L = 4 × 10⁻⁵ × 0.1 = 4 × 10⁻⁶ m, just 4 micrometres.

Worked example 1.6: A wire 3 m long with area 2 mm² (Y = 2 × 10¹¹ Pa) carries a 400 N load. Find the extension, the energy stored and the energy density.

Solution: ΔL = (400 × 3)/(2 × 10⁻⁶ × 2 × 10¹¹) = 3 × 10⁻³ m. U = ½ × 400 × 3 × 10⁻³ = 0.6 J. Volume = 2 × 10⁻⁶ × 3 = 6 × 10⁻⁶ m³, so u = 0.6 / (6 × 10⁻⁶) = 1 × 10⁵ J/m³. Check: stress = 2 × 10⁸ Pa, and stress²/(2Y) = 4 × 10¹⁶ / (4 × 10¹¹) = 1 × 10⁵ J/m³.

Worked example 1.7: A steel rope 10 m long hangs from a hook. Density = 8000 kg/m³, Y = 2 × 10¹¹ Pa. How much does it stretch under its own weight?

Solution: ΔL = ρgL²/(2Y) = (8000 × 10 × 100)/(2 × 2 × 10¹¹) = 2 × 10⁻⁵ m = 0.02 mm. Note that the area cancels.

Worked example 1.8: A wire 2 m long and 1 mm in diameter stretches by 1 mm. Its Poisson's ratio is 0.3. By how much does its diameter shrink?

Solution: Longitudinal strain = 1 × 10⁻³ / 2 = 5 × 10⁻⁴. Lateral strain = 0.3 × 5 × 10⁻⁴ = 1.5 × 10⁻⁴. Δd = 1.5 × 10⁻⁴ × 1 mm = 1.5 × 10⁻⁴ mm, about 0.15 micrometre.

Quick revision

  • Stress = F/A (Pa); strain is a pure number. Hooke's law: stress ∝ strain up to the proportional limit.

  • Y = FL/(AΔL); ΔL = FL/(πr²Y). Y depends on material only, not on L or A.

  • B = −ΔP/(ΔV/V); compressibility = 1/B. Only B exists for all three states.

  • G = F/(Aθ), with A the face the tangential force acts on.

  • Own-weight extension = ρgL²/(2Y) = MgL/(2AY).

  • Poisson's ratio: 0 to 0.5 in practice; 0.5 means volume unchanged.

  • U = ½ F ΔL; energy density = ½ stress × strain = stress²/(2Y).

  • Ductile: large plastic region. Brittle: breaks soon after the elastic limit.

NEET traps

  • Thinking rubber is more elastic than steel. Steel has a much larger Y, so it is more elastic.

  • Using diameter in place of radius in πr², or forgetting to square the ratio of radii.

  • Writing U = F ΔL. The stored energy is half of that.

  • Believing Y changes when you cut the wire shorter. Extension changes; Y does not.

  • In shear problems, using the side area instead of the area of the face the force acts on.

  • Forgetting the factor 3 when going from volume strain to radius strain of a sphere.

Practice MCQs: Chapter 1

Level 1: Concept check

1. The SI unit of Young's modulus is (a) N/m (b) N/m² (c) N m (d) N

2. Strain has (a) no dimensions (b) dimensions of pressure (c) dimensions of length (d) dimensions of force

3. Young's modulus of a perfectly rigid body is (a) zero (b) one (c) infinite (d) dependent on its length

4. Which of these is the most elastic? (a) Rubber (b) Clay (c) Glass (d) Steel

5. Which modulus is defined for solids, liquids and gases? (a) Young's modulus (b) Bulk modulus (c) Modulus of rigidity (d) Poisson's ratio

6. Hooke's law holds up to the (a) fracture point (b) ultimate stress point (c) yield point (d) proportional limit

7. Compressibility of a material with bulk modulus B is (a) 1/B (b) B (c) B² (d) √B

8. Shear strain is measured by (a) ΔL/L (b) ΔV/V (c) the angle of deformation in radians (d) force per unit area

9. The theoretical range of Poisson's ratio is (a) 0 to 1 (b) −1 to 0.5 (c) 0.5 to 1 (d) −0.5 to 1

10. Elastic energy stored per unit volume of a stretched wire equals (a) stress × strain (b) 2 × stress × strain (c) ½ × stress × strain (d) stress / strain

Level 2: NEET standard

11. A steel wire 4 m long with cross-section 2 mm² carries a load of 200 N. Y = 2 × 10¹¹ Pa. Its extension is (a) 2 mm (b) 1 mm (c) 4 mm (d) 0.5 mm

12. Two wires of the same material and length have radii r and 2r. They carry equal loads. The ratio of extension of the thin wire to the thick wire is (a) 1 : 4 (b) 1 : 2 (c) 2 : 1 (d) 4 : 1

13. A wire stretches by 1 mm under a force F. A wire of the same material with twice the length and twice the radius is pulled by the same force. It stretches by (a) 1 mm (b) 0.5 mm (c) 2 mm (d) 0.25 mm

14. The volume of a liquid falls by 0.02% when the pressure on it rises by 2 × 10⁵ Pa. Its bulk modulus is (a) 1 × 10⁷ Pa (b) 4 × 10⁹ Pa (c) 1 × 10⁹ Pa (d) 1 × 10¹¹ Pa

15. A force of 50 N stretches a wire by 2 mm, within the elastic limit. The energy stored is (a) 0.05 J (b) 0.1 J (c) 0.025 J (d) 100 J

16. For a wire with Y = 2 × 10¹¹ Pa, the stress that would double its length (if Hooke's law held throughout) is (a) 1 × 10¹¹ Pa (b) 4 × 10¹¹ Pa (c) 2 × 10¹⁰ Pa (d) 2 × 10¹¹ Pa

17. The load on a wire is doubled and the wire is replaced by one of the same material and length but double the radius. The extension (a) doubles (b) halves (c) stays the same (d) becomes one quarter

18. A block has a 5 cm × 5 cm top face and height 5 cm, with its base fixed. A tangential force of 1000 N on the top face shifts it sideways by 0.02 mm. The modulus of rigidity is (a) 1 × 10⁸ Pa (b) 4 × 10⁹ Pa (c) 1 × 10⁹ Pa (d) 2.5 × 10⁷ Pa

19. In the linear region, the stress-strain line for wire A is steeper than for wire B. Then (a) Y_A > Y_B (b) Y_A < Y_B (c) Y_A = Y_B (d) A must be more ductile than B

20. A wire's volume does not change when it is stretched. Its Poisson's ratio is (a) 0 (b) 0.25 (c) 1 (d) 0.5

21. A wire with Y = 2 × 10¹¹ Pa is under a strain of 10⁻³. The elastic energy density is (a) 2 × 10⁵ J/m³ (b) 1 × 10⁵ J/m³ (c) 1 × 10⁸ J/m³ (d) 2 × 10⁸ J/m³

22. A material shows a long plastic region between its elastic limit and fracture. It is (a) brittle (b) an elastomer (c) ductile (d) perfectly elastic

Level 3: Challenge

23. A copper wire 20 m long hangs from a ceiling. Density = 9000 kg/m³ and Y = 1.2 × 10¹¹ Pa. Its extension under its own weight is (a) 0.30 mm (b) 0.075 mm (c) 1.5 mm (d) 0.15 mm

24. Two wires of the same material and length have radii r and 2r and carry the same load. The ratio of elastic energies stored, U₁ : U₂, is (a) 4 : 1 (b) 1 : 4 (c) 2 : 1 (d) 16 : 1

25. A steel wire (Y = 2 × 10¹¹ Pa) and a copper wire (Y = 1 × 10¹¹ Pa) of equal length and area are joined end to end and a load is hung from the lower end. The ratio of extension of steel to copper is (a) 2 : 1 (b) 1 : 1 (c) 1 : 2 (d) 1 : 4

26. At what depth in the sea does the volume of water fall by 0.5%? Take B = 2.2 × 10⁹ Pa and ρ = 1000 kg/m³; ignore atmospheric pressure and the small change in density. (a) 220 m (b) 1100 m (c) 2200 m (d) 110 m

27. A steel ball (B = 1.6 × 10¹¹ Pa) is subjected to an extra pressure of 4.8 × 10⁸ Pa from all sides. The fractional decrease in its radius is (a) 0.3% (b) 0.03% (c) 1% (d) 0.1%

28. A metal has breaking stress 8 × 10⁸ Pa and density 8000 kg/m³. The longest wire of this metal that can hang vertically without breaking under its own weight is (a) 10 km (b) 1 km (c) 100 km (d) 5 km

29. Assertion (A): Steel is more elastic than rubber. Reason (R): For the same stress, steel shows a much smaller strain than rubber, so its Young's modulus is larger. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: At constant temperature, the bulk modulus of an ideal gas equals its pressure. Statement II: Young's modulus of a wire increases if its length is increased. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1bY = stress/strain, and strain has no unit
2aStrain is a ratio of like quantities
3cNo strain for any stress, so Y → ∞
4dSteel has the largest Y of these
5bFluids resist volume change but not shape change
6dStress ∝ strain only up to the proportional limit
7aCompressibility is defined as 1/B
8cShear strain = θ ≈ Δx/L
9bTheory gives −1 < σ < 0.5
10cu = ½ stress × strain
11aΔL = 200 × 4/(2×10⁻⁶ × 2×10¹¹) = 2 mm
12dΔL ∝ 1/r², so (2r/r)² = 4
13bΔL ∝ L/r² = 2/4 = ½
14cB = 2×10⁵ / 2×10⁻⁴ = 10⁹ Pa
15aU = ½ × 50 × 0.002 = 0.05 J
16dStrain 1 needs stress = Y
17bΔL ∝ F/r² = 2/4
18cStress 4×10⁵ Pa, strain 4×10⁻⁴, G = 10⁹ Pa
19aSlope of stress-strain line is Y
20dσ = 0.5 gives zero volume change
21bu = ½ × 2×10¹¹ × 10⁻⁶ = 10⁵ J/m³
22cLong plastic region means ductile
23dρgL²/(2Y) = 3.6×10⁷/2.4×10¹¹ = 0.15 mm
24aU = F²L/(2AY) ∝ 1/r²
25cSame F, L, A, so ΔL ∝ 1/Y
26bp = 0.005 × 2.2×10⁹ = 1.1×10⁷ Pa, h = p/ρg = 1100 m
27dΔV/V = 3×10⁻³, Δr/r = one third = 0.1%
28aρgL = breaking stress gives L = 8×10⁸/8×10⁴ = 10⁴ m
29aLarger Y means more elastic, and R gives the reason
30cIsothermal B = P is true; Y is a material constant

Chapter 1 revision sheet

One-page summary

  • Elasticity: a body regains its shape when the load is removed. Plasticity: it keeps the new shape.

  • Stress = restoring force/area (N/m² or Pa). Three kinds: longitudinal (tensile or compressive), volume (hydraulic) and shearing (tangential).

  • Strain = change in size/original size; it has no unit. Longitudinal ΔL/L, volume ΔV/V, shear angle θ ≈ x/L.

  • Hooke's law: within the proportional limit, stress ∝ strain; the constant is the modulus of elasticity.

  • Stress-strain curve of a ductile metal: proportional limit, elastic limit (yield point), plastic region, ultimate tensile strength, fracture point.

  • Young's modulus Y = (F/A)/(ΔL/L), so ΔL = FL/(AY).

  • A wire hanging under its own weight stretches ρgL²/(2Y), half of what the same weight would give if hung at its end.

  • Bulk modulus B = −ΔP/(ΔV/V); compressibility K = 1/B. Solids have the largest B, gases the smallest.

  • Modulus of rigidity G = (F/A)/θ for shear. Liquids and gases have G = 0.

  • Poisson's ratio σ = lateral strain/longitudinal strain; no unit; theoretical range −1 to 0.5, usually 0.2–0.4 for metals.

  • Energy stored in a stretched wire: U = ½ F ΔL; energy density u = ½ × stress × strain = stress²/(2Y).

  • Breaking force depends on cross-section area and material, not on length.

  • "More elastic" means a larger modulus: steel is more elastic than rubber.

  • Moduli usually fall as temperature rises.

Must-remember table

QuantityFormulaSI unit
StressF/AN/m² (Pa)
Young's modulusFL/(AΔL)Pa
Bulk modulus−ΔP/(ΔV/V)Pa
Compressibility1/BPa⁻¹ (m²/N)
Modulus of rigidity(F/A)/θPa
Poisson's ratiolateral strain/longitudinal strainnone
Elastic energy½ FΔLJ
Energy density½ stress × strainJ/m³
Steel Y (typical)about 2 × 10¹¹ PaPa

Memory aids

  • "YBG: Yank, Bulk-squeeze, Glide": Y is for a Yank along the length, B for squeezing the Bulk from all sides, G for one face Gliding over the other (shear).

  • "PEYUF" for the stress-strain curve in order: Proportional limit, Elastic limit, Yield (plastic flow), Ultimate strength, Fracture.

  • "L over r-square": extension ∝ L/r² for the same load and material. Say it as "long and thin stretches most".

  • "Half a weight": a wire stretched by its own weight extends half as much as when that weight hangs at the end.

  • "Poisson stops at half": σ can never exceed 0.5 for a real isotropic material.

Concept connections

  • Bulk modulus links to the speed of sound, v = √(B/ρ), in Physics Book 10: Oscillations and Waves.

  • Thermal stress YαΔT joins this chapter to Chapter 6 of this book, and the dimensions of the moduli to Physics Book 1: Physics and Measurement.

  • Elastic energy ½ FΔL is the spring energy ½ kx² of Physics Book 4: Work, Energy and Power, with k = YA/L.

Practice MCQs: Chapter 1, Level 4 (new NEET pattern)

31. Match List I with List II.

List I:

  • A. Young's modulus

  • B. Bulk modulus

  • C. Modulus of rigidity

  • D. Poisson's ratio

List II:

  • (i) Lateral strain divided by longitudinal strain

  • (ii) Tangential stress divided by shear strain

  • (iii) Normal stress divided by longitudinal strain

  • (iv) Pressure change divided by fractional decrease in volume

(a) A-iv, B-iii, C-ii, D-i (b) A-iii, B-ii, C-iv, D-i (c) A-iii, B-iv, C-ii, D-i (d) A-ii, B-iv, C-iii, D-i

32. Match the points on the stress-strain curve of a copper wire (List I) with what happens there (List II).

List I:

  • A. Proportional limit

  • B. Yield point

  • C. Ultimate tensile strength

  • D. Fracture point

List II:

  • (i) Largest stress the wire can bear

  • (ii) Hooke's law stops holding beyond it

  • (iii) The wire snaps

  • (iv) Strain grows a lot with little extra stress (plastic flow begins)

(a) A-ii, B-iv, C-i, D-iii (b) A-iv, B-ii, C-i, D-iii (c) A-ii, B-i, C-iv, D-iii (d) A-ii, B-iv, C-iii, D-i

33. A wire stretches by ΔL under a load. The same load is hung on wires of the same material changed as in List I. Match with the new extension in List II.

List I:

  • A. Length doubled, radius same

  • B. Radius doubled, length same

  • C. Both length and radius doubled

  • D. Wire drawn to twice its length (volume unchanged)

List II:

  • (i) ΔL/4

  • (ii) 4ΔL

  • (iii) 2ΔL

  • (iv) ΔL/2

(a) A-iii, B-iv, C-i, D-ii (b) A-ii, B-i, C-iv, D-iii (c) A-iii, B-i, C-ii, D-iv (d) A-iii, B-i, C-iv, D-ii

34. Match each quantity with its SI unit.

List I:

  • A. Stress

  • B. Strain

  • C. Compressibility

  • D. Elastic energy density

List II:

  • (i) No unit

  • (ii) m² N⁻¹

  • (iii) J m⁻³

  • (iv) N m⁻²

(a) A-iii, B-i, C-ii, D-iv (b) A-iv, B-i, C-ii, D-iii (c) A-iv, B-ii, C-i, D-iii (d) A-ii, B-i, C-iv, D-iii

35. How many of the following statements are correct?

  • A. The Young's modulus of a perfectly rigid body is infinite.

  • B. The bulk modulus of a gas is zero.

  • C. Steel is more elastic than rubber.

  • D. Poisson's ratio of an isotropic metal can be 0.7.

  • E. Elastic energy stored per unit volume equals ½ × stress × strain.

(a) 2 (b) 4 (c) 3 (d) 5

36. Choose the correct set of statements.

  • A. Liquids have zero modulus of rigidity.

  • B. For most metals the shear modulus is roughly one-third of Young's modulus.

  • C. A pure shear changes the volume of a body.

  • D. Bulk modulus is defined for solids, liquids and gases.

(a) A and C only (b) B and C only (c) A, C and D only (d) A, B and D only

37. How many of the following statements are correct?

  • A. A wire hanging under its own weight stretches half as much as when the same weight hangs at its lower end.

  • B. The breaking force of a wire depends on its length.

  • C. The breaking force of a wire is proportional to its area of cross-section.

  • D. Cutting a wire into two halves halves its Young's modulus.

(a) 1 (b) 2 (c) 3 (d) 4

38. Choose the correct set of statements.

  • A. Elastic moduli of most metals decrease as temperature rises.

  • B. A brittle material breaks soon after its elastic limit.

  • C. Rubber obeys Hooke's law over its whole stretch.

  • D. A ductile material has a large plastic region.

(a) A, B and D only (b) A and C only (c) B, C and D only (d) A, B, C and D

39. Load (y-axis) is plotted against extension (x-axis) for two wires P and Q of the same material and the same length. Both graphs are straight lines through the origin, and the slope for P is 4 times the slope for Q. The ratio of radii r_P/r_Q is:

(a) 4 (b) 1/2 (c) √2 (d) 2

40. A student loads a wire of length 2 m and cross-section 1 mm² and records (g = 10 m/s²):

Load (kg)0246
Extension (mm)00.40.81.2

Young's modulus of the wire is:

(a) 2 × 10¹¹ Pa (b) 1 × 10¹¹ Pa (c) 5 × 10¹⁰ Pa (d) 1 × 10¹⁰ Pa

41. Stress (y-axis) versus strain (x-axis) graphs of three materials A, B and C are straight lines from the origin. A is the steepest and C the least steep. For the same stress, which material stores the most elastic energy per unit volume?

(a) A (b) B (c) C (d) All store the same

Passage for Q42–43: A building-site crane lifts a 1000 kg load with a steel cable 10 m long and 1 cm in radius. The load is raised with an upward acceleration of 2 m/s². Take Y for steel = 2 × 10¹¹ Pa and g = 10 m/s². Ignore the cable's own mass.

42. The stress in the cable while the load accelerates is about:

(a) 3.8 × 10⁷ Pa (b) 3.2 × 10⁷ Pa (c) 1.2 × 10⁷ Pa (d) 3.8 × 10⁵ Pa

43. The extension of the cable is about:

(a) 0.19 mm (b) 19 mm (c) 1.6 mm (d) 1.9 mm

44. Two wires of the same material, of lengths L and 2L and radii 2r and r, are joined end to end and a load hangs from the bottom. The ratio of the elastic energies stored in the first and the second wire is:

(a) 8 : 1 (b) 1 : 8 (c) 1 : 2 (d) 1 : 4

45. A copper sphere (bulk modulus 1.4 × 10¹¹ Pa) is lowered 1.4 km into the sea. Take the density of sea water as 1000 kg/m³ and g = 10 m/s². The fractional decrease in its radius is about:

(a) 1 × 10⁻⁴ (b) 3 × 10⁻⁴ (c) 3.3 × 10⁻⁵ (d) 1 × 10⁻⁵

Level 4 answer key

QAnsReason
31cY uses normal stress, B uses volume strain, G uses shear, σ is a strain ratio
32aHooke's law ends, then yield, then the peak stress, then fracture
33dΔL ∝ L/r²: 2, 1/4, 2/4 = 1/2; drawn to 2L halves the area, so 2 × 2 = 4
34bStress Pa, strain none, K = 1/B in m²/N, energy density J/m³
35cA, C, E true; a gas has finite B (equal to P when isothermal); σ cannot exceed 0.5
36dShear changes shape, not volume; the rest are true
37bA and C true; breaking force is independent of length; Y is a material property
38aRubber's stress-strain graph is not a straight line
39dSlope = YA/L, so A_P = 4A_Q and r_P = 2r_Q
40bY = FL/(AΔL) = 20 × 2/(10⁻⁶ × 0.4 × 10⁻³) = 1 × 10¹¹ Pa
41cu = stress²/(2Y), largest for the smallest Y, which is the least steep line
42aT = m(g + a) = 12 000 N; A = π × 10⁻⁴ m²; stress = 3.82 × 10⁷ Pa
43dΔL = stress × L/Y = 3.82 × 10⁷ × 10/(2 × 10¹¹) = 1.9 × 10⁻³ m
44bSame F, so U ∝ ΔL ∝ L/r²: (L/4r²) : (2L/r²) = 1 : 8
45cΔP = ρgh = 1.4 × 10⁷ Pa; ΔV/V = 10⁻⁴; Δr/r = one-third of that
28 min left
‹
›