Chapter 4 of 12 · 26 min read

Chapter 2: Fluid Pressure and Pascal's Law

What you will learn

  • What pressure is, and why it is a scalar.

  • How pressure grows with depth, P = P₀ + ρgh, and why the shape of the vessel does not matter.

  • Atmospheric, gauge and absolute pressure; barometers and manometers.

  • Pascal's law and its use in hydraulic lifts and brakes.

  • How gravity (and acceleration of the container) changes pressure in a liquid.

  • Archimedes' principle, floating and apparent weight.

2.1 Fluids and pressure

A fluid is anything that flows: liquids and gases. A fluid at rest cannot push sideways along a surface. It can only push at right angles to any surface it touches.

Pressure is the normal force per unit area.

P=F⊥AP = \frac{F_{\perp}}{A}

SI unit: pascal (1 Pa = 1 N/m²). Other units: 1 atm = 1.013 × 10⁵ Pa, 1 bar = 10⁵ Pa, 1 torr = 1 mm of Hg ≈ 133 Pa.

Pressure is a scalar. At a point in a fluid at rest, it is the same in every direction. A force arises only when pressure acts on a surface, and that force is always normal to the surface.

This is why a nail with a sharp tip goes into wood easily: the same force acts on a tiny area, so the pressure is huge. A camel's wide feet do the opposite on sand.

Density ρ = mass/volume (kg/m³). Water is 1000 kg/m³, mercury 13 600 kg/m³. Relative density is density divided by the density of water at 4 °C; it has no unit.

2.2 Pressure due to a fluid column

Take a cylinder of liquid with cross-section A and height h, inside a large liquid at rest. Its top is at the surface, where the pressure is P₀ (atmospheric). Let the pressure at its bottom be P.

Vertical forces on this cylinder:

  • P₀A downward on the top face.

  • Its weight, mg = ρAhg, downward.

  • PA upward on the bottom face.

The side forces cancel. For equilibrium:

PA=P0A+ρAhg⇒P=P0+ρghP A = P_0 A + \rho A h g \quad\Rightarrow\quad P = P_0 + \rho g h

This is the effect of gravity on fluid pressure. Three results follow directly:

  1. Pressure grows linearly with depth. Dams are made thicker at the bottom for this reason.

  2. Points at the same horizontal level in the same connected liquid at rest have the same pressure.

  3. The pressure at a depth does not depend on the shape of the vessel or the amount of liquid. Vessels of different shapes filled to the same height have equal pressure at their bases. This is the hydrostatic paradox.

For two points inside the same liquid with a height difference h, P₂ − P₁ = ρgh. Without gravity (or in free fall), this difference vanishes.

2.3 Atmospheric, gauge and absolute pressure

The air above us has weight, so it presses on everything. At sea level this atmospheric pressure is about 1.013 × 10⁵ Pa.

A mercury barometer measures it. A glass tube about 1 m long is filled with mercury and turned upside down in a dish of mercury. The column falls until its weight per unit area equals the atmospheric pressure. The space above is nearly a vacuum.

P0=ρHg g h≈13600×9.8×0.76≈1.013×105 PaP_0 = \rho_{Hg}\, g\, h \approx 13600 \times 9.8 \times 0.76 \approx 1.013 \times 10^5\ \text{Pa}

So 1 atm = 76 cm of mercury. Mercury is used because its high density keeps the column short. A water barometer would need a tube over 10 m tall.

  • Absolute pressure = the total pressure at a point, P.

  • Gauge pressure = P − P₀, the excess over atmospheric. A tyre gauge or a blood pressure meter shows gauge pressure.

An open-tube manometer is a U-tube with liquid. One end connects to the gas; the other is open to air. If the liquid on the open side stands h higher, the gas has gauge pressure ρgh.

2.4 Pascal's law and its applications

Pascal's law: a change in pressure applied to an enclosed fluid is passed on undiminished to every part of the fluid and to the walls of its container.

Press the cap of a toothpaste tube anywhere, and paste comes out at the nozzle. That is Pascal's law at home.

Hydraulic lift. Two cylinders of different areas, A₁ (small) and A₂ (large), are joined and filled with oil. Each has a piston. Push the small piston with force F₁. The extra pressure F₁/A₁ reaches the large piston unchanged:

F1A1=F2A2⇒F2=F1 A2A1\frac{F_1}{A_1} = \frac{F_2}{A_2} \quad\Rightarrow\quad F_2 = F_1\,\frac{A_2}{A_1}
Figure 2.1 · Hydraulic lift
Figure 2.1 · Hydraulic lift

The small force F₁ creates an extra pressure that the oil carries to the large piston, where it acts on a much larger area.

The force is multiplied by A₂/A₁. Energy is not multiplied. Oil is nearly incompressible, so the volume pushed out of one cylinder enters the other: A₁d₁ = A₂d₂. The small piston moves a long way while the large one rises a little. Work in = F₁d₁ = F₂d₂ = work out (ignoring losses).

Other uses: hydraulic brakes in cars and buses (the pedal force reaches all four wheel cylinders equally), hydraulic jacks at a roadside tyre shop, the hydraulic press used to bale cotton, and the dentist's chair.

2.5 Effect of gravity and acceleration on fluid pressure

The pressure difference ρgh exists only because gravity gives the liquid weight. Change the effective gravity and the pressure changes.

Situation of the containerPressure difference over a depth h
At rest or moving at constant velocityρgh
In a lift accelerating upward at aρ(g + a)h
In a lift accelerating downward at a (a < g)ρ(g − a)h
Freely falling (a = g)zero

If a tanker of water accelerates horizontally with acceleration a, the free surface tilts. It becomes perpendicular to the effective gravity, so the angle with the horizontal is given by:

tan⁡θ=ag\tan\theta = \frac{a}{g}

2.6 Buoyancy and Archimedes' principle

A mug feels lighter when you lift it inside a bucket of water. The water pushes up on it. This upward force is the buoyant force (upthrust).

Where does it come from? Take a cube of side L under water, with its top at depth h. The pressure on its bottom face is greater than on its top face by ρgL. Net upward force = ρgL × L² = ρ g L³. That is exactly the weight of the liquid the cube displaces.

Archimedes' principle: a body wholly or partly immersed in a fluid feels an upward force equal to the weight of the fluid it displaces.

FB=ρfluid Vsub gF_B = \rho_{fluid}\, V_{sub}\, g

Consequences:

  • Apparent weight = true weight − buoyant force.

  • Relative density of a solid = weight in air / loss of weight in water.

  • A body floats when the buoyant force on its submerged part equals its weight. Then the fraction submerged is V_sub/V = ρ_body/ρ_fluid.

  • A body denser than the fluid sinks; one less dense rises to the surface and floats.

  • A ship floats lower in fresh water than in sea water, because fresh water is less dense and more of it must be displaced.

  • Ice floating in water: when it melts, the level stays the same. The melted water exactly fills the volume the ice had displaced.

Worked example 2.1: Find the absolute and gauge pressure at the bottom of a 10 m deep lake. Take P₀ = 1 × 10⁵ Pa.

Solution: Gauge pressure = ρgh = 1000 × 10 × 10 = 1 × 10⁵ Pa. Absolute pressure = 1 × 10⁵ + 1 × 10⁵ = 2 × 10⁵ Pa, about 2 atm. Every 10 m of water adds about one atmosphere.

Worked example 2.2: A car of mass 1200 kg sits on the large piston (radius 20 cm) of a hydraulic lift. The small piston has radius 2 cm. What force on the small piston holds the car up?

Solution: F₁ = F₂ × (A₁/A₂) = 12 000 × (2/20)² = 12 000 × 0.01 = 120 N. That is the weight of a 12 kg bag.

Worked example 2.3: Atmospheric pressure supports 76 cm of mercury. How tall a water column would it support? Relative density of mercury = 13.6.

Solution: Same pressure means ρ_w h_w = ρ_Hg h_Hg. h_w = 13.6 × 0.76 = 10.3 m. g cancels.

Worked example 2.4: A U-tube holds water. Oil is poured into one arm. When balanced, a 10 cm oil column above the oil-water interface balances 8 cm of water above the same level in the other arm. Find the density of oil.

Solution: The interface level has equal pressure in both arms. ρ_oil × 10 = 1000 × 8, so ρ_oil = 800 kg/m³.

Worked example 2.5: Ice (917 kg/m³) floats in sea water (1030 kg/m³). What fraction of an iceberg is under water?

Solution: Fraction submerged = 917/1030 = 0.89. About 89% is hidden, which is why icebergs are dangerous to ships.

Worked example 2.6: A stone weighs 30 N in air and 20 N when fully under water. Find its volume and density.

Solution: Buoyant force = 30 − 20 = 10 N = ρ_w V g. V = 10/(1000 × 10) = 1 × 10⁻³ m³. Mass = 3 kg, so density = 3000 kg/m³ (relative density 30/10 = 3).

Worked example 2.7: A bucket of water stands in a lift accelerating upward at 2 m/s². Find the gauge pressure at a depth of 50 cm.

Solution: Effective g = 10 + 2 = 12 m/s². Gauge pressure = 1000 × 12 × 0.5 = 6000 Pa. At rest it would be 5000 Pa.

Worked example 2.8: A rectangular tank is 2 m wide and holds water 3 m deep. Find the force of the water (gauge) on one 2 m wide side wall.

Solution: Pressure grows from 0 at the top to ρgh at the bottom, linearly. The average gauge pressure is ρgh/2. Force = (ρgh/2) × (h × w) = ½ × 1000 × 10 × 3² × 2 = 9 × 10⁴ N.

Quick revision

  • P = F⊥/A, a scalar; same in all directions at a point in a fluid at rest.

  • P = P₀ + ρgh; independent of vessel shape. Same level, same liquid, same pressure.

  • Gauge = absolute − atmospheric. 1 atm = 76 cm Hg ≈ 10.3 m of water ≈ 1.013 × 10⁵ Pa.

  • Pascal: F₂/F₁ = A₂/A₁; A₁d₁ = A₂d₂; no gain in work.

  • Lift up: ρ(g + a)h; lift down: ρ(g − a)h; free fall: zero. Horizontal acceleration: tan θ = a/g.

  • Buoyant force = ρ_fluid V_sub g. Floating: V_sub/V = ρ_body/ρ_fluid.

  • Relative density = weight in air / loss of weight in water.

NEET traps

  • Adding atmospheric pressure when the question asks for gauge pressure, or forgetting it when it asks for absolute pressure.

  • Thinking a wider vessel gives more pressure at the base. Only the depth matters.

  • Believing a hydraulic lift multiplies energy. It multiplies force only.

  • Using the body's density in the buoyant force. Buoyancy uses the fluid's density and the submerged volume.

  • Using radius ratio directly for the area ratio in a hydraulic lift. Area goes as r².

  • Saying the water level rises when floating ice melts. It stays the same.

Practice MCQs: Chapter 2

Level 1: Concept check

1. Pressure is (a) a vector along the force (b) a scalar (c) a vector normal to the surface (d) dimensionless

2. The absolute pressure at depth h in a liquid of density ρ, open to the air at pressure P₀, is (a) ρgh (b) P₀ − ρgh (c) P₀ + ρgh (d) P₀/(ρgh)

3. Gauge pressure equals (a) absolute pressure + atmospheric pressure (b) absolute pressure − atmospheric pressure (c) atmospheric pressure − absolute pressure (d) atmospheric pressure always

4. A hydraulic lift works on (a) Archimedes' principle (b) Bernoulli's principle (c) Pascal's law (d) Hooke's law

5. One standard atmosphere is about (a) 1.013 × 10⁵ Pa (b) 1.013 × 10³ Pa (c) 76 Pa (d) 10⁶ Pa

6. Three vessels of different shapes but equal base area are filled with water to the same height. The pressure at the base is (a) greatest in the widest vessel (b) greatest in the narrowest vessel (c) the same in all three (d) proportional to the volume of water

7. The buoyant force on a body in a fluid equals (a) the weight of the body (b) the weight of the fluid displaced (c) the volume of the body (d) the mass of the body

8. A block floats in water with one quarter of its volume above the surface. Its density is (a) 250 kg/m³ (b) 1333 kg/m³ (c) 1000 kg/m³ (d) 750 kg/m³

9. A closed jar of water falls freely. The pressure difference between the top and bottom of the water due to the water is (a) ρgh (b) 2ρgh (c) zero (d) very large

10. Mercury is preferred in a barometer mainly because (a) its high density keeps the column short (b) its density is low (c) it is transparent (d) it wets glass

Level 2: NEET standard

11. A tank holds water 5 m deep and is open to the air (P₀ = 1 × 10⁵ Pa). The absolute pressure at the bottom is (a) 5 × 10⁴ Pa (b) 1.5 × 10⁵ Pa (c) 1.05 × 10⁵ Pa (d) 6 × 10⁵ Pa

12. In a hydraulic press the small piston has area 5 cm² and the large piston 500 cm². A force of 100 N on the small piston can support a load of (a) 1 N (b) 1000 N (c) 10⁴ N (d) 10⁵ N

13. In the press of Q12, the small piston moves down by 20 cm. The large piston rises by (a) 2 mm (b) 2 cm (c) 20 cm (d) 0.2 mm

14. Taking 1 atm = 1 × 10⁵ Pa, a pressure of 0.5 atm equals a water column of height (a) 0.5 m (b) 50 m (c) 10 m (d) 5 m

15. A body weighs 50 N in air and 40 N when fully immersed in water. Its relative density is (a) 1.25 (b) 5 (c) 4 (d) 0.8

16. Wood of density 600 kg/m³ floats in a liquid of density 800 kg/m³. The fraction of its volume submerged is (a) 0.48 (b) 0.6 (c) 0.75 (d) 0.8

17. A U-tube contains mercury. Water is poured into one arm until the water column is 27.2 cm long. The difference between the mercury levels in the two arms is (a) 2 cm (b) 1 cm (c) 13.6 cm (d) 27.2 cm

18. A tyre gauge reads 2 × 10⁵ Pa. With atmospheric pressure 1 × 10⁵ Pa, the absolute pressure of air in the tyre is (a) 1 × 10⁵ Pa (b) 2 × 10⁵ Pa (c) 4 × 10⁵ Pa (d) 3 × 10⁵ Pa

19. The gauge pressure on a diver 20 m below the surface of the sea (ρ = 1030 kg/m³) is (a) 2.06 × 10⁵ Pa (b) 3.06 × 10⁵ Pa (c) 1.03 × 10⁵ Pa (d) 2.06 × 10⁴ Pa

20. A bucket of water is in a lift accelerating downward at a (a < g). The gauge pressure at depth h is (a) ρ(g + a)h (b) ρgh (c) ρah (d) ρ(g − a)h

21. An ice cube floats in a glass filled with water to the brim. When the ice melts, the water level (a) rises and water spills (b) stays the same (c) falls (d) first falls, then rises

22. A blood pressure of 120 mm of Hg, expressed in pascal, is about (a) 1.6 × 10³ Pa (b) 1.2 × 10⁵ Pa (c) 1.6 × 10⁴ Pa (d) 1.6 × 10⁵ Pa

Level 3: Challenge

23. A tank 2 m wide holds water 3 m deep. The gauge force of the water on one side wall is (a) 1.8 × 10⁵ N (b) 9 × 10⁴ N (c) 4.5 × 10⁴ N (d) 6 × 10⁴ N

24. A wooden block floats in water with 0.7 of its volume submerged, and in an oil with 0.875 of its volume submerged. The density of the oil is (a) 800 kg/m³ (b) 875 kg/m³ (c) 700 kg/m³ (d) 612 kg/m³

25. A cube of side 10 cm and density 500 kg/m³ floats in water. The extra mass that must be placed on it so that it is just fully submerged is (a) 0.25 kg (b) 1 kg (c) 0.5 kg (d) 5 kg

26. A tanker carrying water accelerates horizontally at 5 m/s². The angle of the water surface with the horizontal is (a) tan⁻¹(2) (b) 30° (c) 45° (d) tan⁻¹(0.5)

27. A beaker holds a 20 cm layer of oil (800 kg/m³) floating on a 30 cm layer of water. The gauge pressure at the bottom is (a) 4600 Pa (b) 5000 Pa (c) 4000 Pa (d) 3000 Pa

28. A ball of density 400 kg/m³ is released from rest at the bottom of a pond. Ignoring viscosity, its upward acceleration is (a) 6 m/s² (b) 10 m/s² (c) 15 m/s² (d) 25 m/s²

29. Assertion (A): A ship floats higher in fresh river water than in sea water. Reason (R): Sea water is denser than fresh water. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: At a point in a fluid at rest, pressure is the same in all directions. Statement II: Two points at the same horizontal level in the same connected liquid at rest have equal pressure. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1bPressure has no direction of its own
2cWeight of the column adds ρgh to P₀
3bGauge = excess over atmospheric
4cPressure is transmitted undiminished
5a76 cm Hg ≈ 1.013 × 10⁵ Pa
6cPressure depends only on depth
7bArchimedes' principle
8d3/4 submerged gives ρ = 0.75 × 1000
9cEffective g is zero in free fall
10aHigh density gives a 76 cm column instead of 10 m
11b10⁵ + 1000 × 10 × 5 = 1.5 × 10⁵ Pa
12cF₂ = 100 × 500/5 = 10⁴ N
13ad₂ = 20 cm × 5/500 = 0.2 cm
14dh = 0.5 × 10⁵/(1000 × 10) = 5 m
15b50/(50 − 40) = 5
16c600/800 = 0.75
17a27.2/13.6 = 2 cm of Hg
18dAbsolute = gauge + atmospheric
19a1030 × 10 × 20 = 2.06 × 10⁵ Pa
20dEffective g is g − a
21bMelt water fills exactly the displaced volume
22c0.12 × 13 600 × 10 ≈ 1.6 × 10⁴ Pa
23b½ρgh²w = ½ × 1000 × 10 × 9 × 2
24aρ_wood = 700, so ρ_oil = 700/0.875 = 800
25c(1000 − 500) × 10⁻³ m³ = 0.5 kg
26dtan θ = a/g = 0.5
27a800 × 10 × 0.2 + 1000 × 10 × 0.3 = 4600 Pa
28ca = g(σ − ρ)/ρ = 10 × 600/400
29dLess dense fresh water means the ship sinks deeper, so A is false
30aBoth are basic facts of hydrostatics

Chapter 2 revision sheet

One-page summary

  • A fluid flows because it cannot resist a shear stress at rest. Liquids and gases are both fluids.

  • Pressure P = F⊥/A. It is a scalar. SI unit pascal (Pa = N/m²). Dimensions [M L⁻¹ T⁻²].

  • At a point in a fluid at rest, pressure is the same in every direction.

  • Pressure at depth h: P = P₀ + ρgh. It does not depend on the shape of the vessel or the amount of liquid.

  • Points at the same level in the same connected liquid at rest have the same pressure.

  • Gauge pressure = absolute pressure − atmospheric pressure. It can be negative (suction).

  • 1 atm = 76 cm of Hg ≈ 10.3 m of water ≈ 1.013 × 10⁵ Pa. 1 bar = 10⁵ Pa. 1 torr ≈ 1 mm Hg.

  • Barometer: P₀ = ρ_Hg g h. Open-tube manometer: gauge pressure = ρgh of the level difference.

  • Pascal's law: extra pressure applied to an enclosed liquid reaches every part of it undiminished.

  • Hydraulic lift: F₂/F₁ = A₂/A₁. Volume pushed is shared: A₁d₁ = A₂d₂. Force is multiplied, work is not.

  • In a lift with acceleration a: up → ρ(g + a)h, down → ρ(g − a)h, free fall → zero gauge pressure.

  • Tanker accelerating horizontally: surface tilts, tan θ = a/g, liquid piles up at the rear.

  • Archimedes: buoyant force F_B = ρ_fluid × V_submerged × g, acting at the centre of buoyancy.

  • Floating: weight = buoyant force, so V_sub/V = ρ_body/ρ_fluid.

  • Relative density = weight in air ÷ loss of weight in water.

Must-remember table

QuantityFormula or valueUnit or note
PressureP = F⊥/APa = N/m²
Pressure at depthP = P₀ + ρghshape of vessel does not matter
Gauge pressureP − P₀ = ρghcan be negative
Atmosphere1.013 × 10⁵ Pa = 76 cm Hg≈ 10.3 m water
Hydraulic liftF₂ = F₁ × A₂/A₁A₁d₁ = A₂d₂
Liquid in liftρ(g ± a)hzero in free fall
Horizontal accelerationtan θ = a/gsurface tilts
Buoyant forceρ_fluid V_sub gindependent of body's density
Floating fractionV_sub/V = ρ_body/ρ_fluidice in water ≈ 0.9
Relative densityW_air / (W_air − W_water)no unit

Memory aids

  • "Deep Down, Pressure Grows": D for depth, D for density, P for P₀ added on top, G for g. All four appear in P = P₀ + ρgh.

  • "Pascal Passes, Archimedes Lifts": Pascal's law passes pressure through a closed liquid; Archimedes' principle gives the lifting (buoyant) force.

  • "Fraction = Ratio": the fraction of a floating body under the surface equals the ratio of its density to the liquid's density.

  • "Lift Up, Pressure Up": a lift accelerating up raises the effective g to g + a, so liquid pressure rises; going down lowers it.

  • "Air over Loss": relative density = weight in Air over Loss of weight in water.

Concept connections

  • Physics Book 3: Laws of Motion: buoyant force and apparent weight are force-balance problems; pseudo force explains liquid in an accelerating lift or tanker.

  • Physics Book 9: Kinetic Theory of Gases: gas pressure comes from molecular collisions, the microscopic picture behind P = F/A.

  • Biology Book 5: Human Physiology: blood pressure is a gauge pressure, read in mm Hg on a sphygmomanometer.

Practice MCQs: Chapter 2, Level 4 (new NEET pattern)

31. Match List I with List II (take g = 10 m/s², P₀ = 1.0 × 10⁵ Pa, ρ_water = 1000 kg/m³ unless stated).

List I:

  • A. Gauge pressure 5 m below the surface of a pond

  • B. Absolute pressure 5 m below the surface of a pond

  • C. Pressure of a 76 cm mercury column (ρ = 13600 kg/m³, g = 9.8 m/s²)

  • D. Pressure under the feet of a 50 kg girl standing on 0.025 m² area

List II:

  • i. 2 × 10⁴ Pa

  • ii. 1.5 × 10⁵ Pa

  • iii. 5 × 10⁴ Pa

  • iv. 1.013 × 10⁵ Pa

(a) A-ii, B-iii, C-iv, D-i (b) A-iii, B-ii, C-i, D-iv (c) A-iii, B-ii, C-iv, D-i (d) A-i, B-ii, C-iv, D-iii

32. Match each device or fact in List I with the idea behind it in List II.

List I:

  • A. Hydraulic brakes of an auto-rickshaw

  • B. A loaded cargo ship staying afloat

  • C. Mercury barometer

  • D. Dam wall made thicker at the bottom

List II:

  • i. Archimedes' principle

  • ii. Pascal's law

  • iii. Pressure rises with depth

  • iv. Atmospheric pressure balances a liquid column

(a) A-ii, B-i, C-iv, D-iii (b) A-i, B-ii, C-iv, D-iii (c) A-ii, B-i, C-iii, D-iv (d) A-iv, B-i, C-ii, D-iii

33. A beaker of liquid (density ρ) sits in different situations. Match the situation with the gauge pressure at depth h.

List I:

  • A. Lift accelerating upward at a

  • B. Lift accelerating downward at a (a less than g)

  • C. Lift whose cable has snapped (free fall)

  • D. Beaker at rest on the Moon (g_Moon = g/6)

List II:

  • i. ρ(g − a)h

  • ii. Zero

  • iii. ρ(g + a)h

  • iv. ρgh/6

(a) A-i, B-iii, C-ii, D-iv (b) A-iii, B-ii, C-i, D-iv (c) A-iii, B-i, C-iv, D-ii (d) A-iii, B-i, C-ii, D-iv

34. Match each floating body with the fraction of its volume under the liquid surface.

List I:

  • A. Ice (900 kg/m³) in water

  • B. Teak wood (600 kg/m³) in water

  • C. Cork (250 kg/m³) in water

  • D. A plastic toy (750 kg/m³) in a liquid of density 1500 kg/m³

List II:

  • i. 0.5

  • ii. 0.25

  • iii. 0.9

  • iv. 0.6

(a) A-iv, B-iii, C-ii, D-i (b) A-iii, B-iv, C-ii, D-i (c) A-iii, B-iv, C-i, D-ii (d) A-iii, B-ii, C-iv, D-i

35. How many of the following statements are correct?

  • A. At a point in a fluid at rest, pressure acts equally in all directions.

  • B. The pressure at the bottom of a vessel depends on the shape of the vessel.

  • C. The buoyant force on a fully immersed body depends on the density of the body.

  • D. In an ideal hydraulic lift, the work done on the small piston equals the work done by the large piston.

  • E. Gauge pressure can be negative.

(a) 2 (b) 3 (c) 4 (d) 5

36. A solid is fully immersed in water and released. Choose the correct set of statements.

  • A. If the solid is denser than water, it sinks.

  • B. Its apparent weight equals its true weight minus the buoyant force.

  • C. The buoyant force acts through the centre of gravity of the solid.

  • D. Once fully under water, the buoyant force does not change as it sinks deeper (water taken as incompressible).

(a) A and B only (b) B, C and D only (c) A, C and D only (d) A, B and D only

37. How many of these unit facts are correct?

  • A. 1 atm ≈ 1.013 × 10⁵ Pa

  • B. 1 bar = 10⁵ Pa

  • C. 1 torr ≈ 1 mm of Hg

  • D. 1 Pa = 1 N/cm²

(a) 1 (b) 2 (c) 3 (d) 4

38. A tanker half full of water accelerates horizontally with acceleration a on a straight road. Choose the correct set.

  • A. The free surface tilts at angle θ with tan θ = a/g.

  • B. The water level rises at the rear end of the tank.

  • C. Pressure is the same at all points on a horizontal line inside the water.

  • D. If a = g, the surface makes 45° with the horizontal.

(a) A, B and D only (b) A and C only (c) B, C and D only (d) A, B, C and D

39. For a liquid in an open tank, a graph of absolute pressure P (y-axis) against depth h (x-axis) is a straight line. It cuts the P-axis at 1.0 × 10⁵ Pa and passes through P = 1.24 × 10⁵ Pa at h = 3 m. The density of the liquid is (g = 10 m/s²)

(a) 600 kg/m³ (b) 800 kg/m³ (c) 1000 kg/m³ (d) 1200 kg/m³

40. A student hangs a stone from a spring balance and records:

Stone inReading (N)
Air6.0
Water4.0
Liquid X4.4

The relative density of the stone and the density of liquid X are

(a) 1.5 and 800 kg/m³ (b) 3 and 1250 kg/m³ (c) 3 and 800 kg/m³ (d) 1.5 and 1250 kg/m³

41. A cylinder is lowered slowly into water. A graph of buoyant force F (y-axis) against the depth d of its bottom face (x-axis) rises as a straight line from 0 at d = 0 to 20 N at d = 0.4 m, then stays flat at 20 N for larger d. The cross-sectional area of the cylinder and the reason for the flat part are (g = 10 m/s²)

(a) 5 cm²; water density rises with depth (b) 500 cm²; the cylinder is fully submerged (c) 50 cm²; water density rises with depth (d) 50 cm²; the cylinder is fully submerged

Passage for Q42–43: A car service station uses a hydraulic lift. The small piston has a diameter of 4 cm and the large piston a diameter of 40 cm. The car and platform together have a mass of 1500 kg. Ignore friction and the weight of the pistons. Take g = 10 m/s².

42. The force needed on the small piston to hold the car steady is

(a) 150 N (b) 1500 N (c) 15 N (d) 375 N

43. To raise the car by 10 cm, the total distance through which the small piston must be pushed (over many strokes) is

(a) 1 m (b) 0.1 m (c) 10 m (d) 100 m

44. A wooden block floats in water with 3/5 of its volume submerged and in oil with 3/4 submerged. The beaker of water is then placed in a lift accelerating upward at 2 m/s². The density of the oil and the new submerged fraction in water are

(a) 800 kg/m³ and 0.72 (b) 750 kg/m³ and 3/5 (c) 800 kg/m³ and 0.5 (d) 800 kg/m³ and 3/5

45. Mercury (13600 kg/m³) is at the same level in both arms of a U-tube. Water is poured into the left arm until the water column is 27.2 cm long. The difference between the mercury levels in the two arms is now

(a) 1.0 cm (b) 2.0 cm (c) 2.7 cm (d) 4.0 cm

Level 4 answer key

QAnsReason
31cρgh = 5 × 10⁴ Pa; add P₀ for 1.5 × 10⁵ Pa; 0.76 × 13600 × 9.8 ≈ 1.013 × 10⁵ Pa; 500/0.025 = 2 × 10⁴ Pa
32aBrakes: Pascal; ship: Archimedes; barometer: P₀ = ρgh; dam: pressure grows with depth
33dEffective g becomes g + a, g − a, 0 and g/6
34bFraction = ρ_body/ρ_liquid: 0.9, 0.6, 0.25, 0.5
35bA, D, E true; B false (shape does not matter); C false (depends on fluid density and volume)
36dBuoyant force acts at the centre of buoyancy, not the centre of gravity
37c1 Pa = 1 N/m², not N/cm²; the other three are true
38aPressure varies along a horizontal line in an accelerating liquid, so C is false
39bSlope ρg = 0.24 × 10⁵/3 = 8000 Pa/m, so ρ = 800 kg/m³
40cRD = 6/2 = 3; loss in X/loss in water = 1.6/2 = 0.8, so 800 kg/m³
41d20 = 1000 × 10 × A × 0.4 gives A = 0.005 m²; flat once fully under water
42aArea ratio = (40/4)² = 100; F₁ = 15000/100 = 150 N
43cA₁d₁ = A₂d₂, so d₁ = 100 × 0.1 m = 10 m
44dρ_wood = 600; ρ_oil = 600/(3/4) = 800; fraction is set by density ratio, not g
45b0.272 × 1000 = h × 13600 gives h = 0.02 m
26 min left
‹
›