Chapter 2: Ampere's Circuital Law
Ampere's law links the field along a closed loop to the current passing through that loop. When the set-up is symmetric, it gives the field in two lines, where Biot–Savart would need a long integral.
What you will learn
The statement and meaning of Ampere's circuital law.
How to choose an Amperian loop.
The field inside and outside a long straight wire (thin, solid and hollow).
The field of a long solenoid, at its centre and at its ends.
The field of a toroid, inside its core and outside it.
2.1 Statement of Ampere's law
Take any closed path in space. Break it into small steps dl. At each step, take the component of B along dl and multiply by dl. Add these up around the whole loop. The total equals μ₀ times the net current passing through the surface bounded by the loop.
Points to keep straight:
The loop is imaginary. It is called an Amperian loop.
I_enc is the net current. Currents in opposite directions are subtracted.
Sign rule: curl the fingers of your right hand along the direction you go around the loop. Currents along your thumb count as positive.
Currents outside the loop do change B at points on the loop. They just add zero to the total line integral.
The law holds for steady currents and any loop. It is useful only when symmetry lets us pull B out of the integral.
Amperian loops are chosen so that along each part of the loop, B is either parallel to dl with constant magnitude, or perpendicular to dl.
Quick check with a long wire. Take a circle of radius r around a long wire. By symmetry, B has the same magnitude everywhere on the circle and points along it. So the line integral is B × 2πr. Setting this equal to μ₀I gives B = μ₀I/(2πr), the result of Chapter 1 in one line.
2.2 Field of a long solid cylindrical wire
A long wire of radius R carries current I spread uniformly over its cross-section. The current density is J = I/(πR²).
Outside (r greater than R). A circular loop of radius r encloses the full current I:
Inside (r less than R). The loop encloses only part of the current, in proportion to area:
So B grows linearly from zero at the axis to its largest value μ₀I/(2πR) at the surface. Outside, it falls as 1/r.

The field rises in a straight line from zero on the axis to its peak at the surface, then falls as 1/r, so R/2 and 2R share the same value.
Hollow pipe (thin cylindrical shell). All the current flows on the surface. A loop inside the pipe encloses no current, so B = 0 inside. Outside, B = μ₀I/(2πr), the same as a thin wire.
Thick hollow cylinder (inner radius a, outer radius b, uniform current I in the metal). For a less than r less than b:
Coaxial cable. The inner wire carries I one way. The outer sheath carries I back. Outside the cable, the net enclosed current is zero, so B = 0. This is why TV and broadband cables use coaxial design: they do not spray magnetic field around.
| Conductor (current I) | Inside (r less than R) | At surface | Outside (r greater than R) |
|---|---|---|---|
| Thin wire | not defined | not defined | μ₀I/(2πr) |
| Solid wire, uniform current | μ₀Ir/(2πR²) | μ₀I/(2πR), the maximum | μ₀I/(2πr) |
| Thin hollow pipe | 0 | μ₀I/(2πR) just outside | μ₀I/(2πr) |
| Coaxial cable (equal, opposite currents) | depends on region | depends on region | 0 |
2.3 Field of a long solenoid
A solenoid is a long wire wound as a tight helix on a cylinder. Let n be the number of turns per unit length (n = N/L, unit m⁻¹). Each turn acts as a loop. Inside, the fields of all the turns add along the axis. Outside, they nearly cancel.
For an ideal solenoid (length much greater than radius, turns tightly packed):
Inside, B is uniform and along the axis.
Outside, B is practically zero.
Derivation. Take a rectangular Amperian loop abcd. Side ab (length h) runs inside, parallel to the axis. Side cd runs outside. Sides bc and da cross the winding at right angles.
Along ab: B is along dl, so the contribution is Bh.
Along bc and da: inside, B is perpendicular to dl; outside, B = 0. Contribution zero.
Along cd: B = 0 outside. Contribution zero.
The loop encloses nh turns, each carrying I. So:

Only side ab, running inside along the uniform field, adds to the line integral; the loop threads nh turns, which gives B = μ₀nI.
The answer does not depend on the radius of the solenoid or on where the point is inside it. At either end of a long solenoid, the field is half:
Why half? A point at the end sees solenoid on one side only. A point in the middle sees two such halves.
If the solenoid has a core of relative permeability μᵣ, the field becomes B = μ₀μᵣnI. Chapter 7 explains this.
An electric bell, a door lock solenoid and the starter relay in a scooter all use this uniform inside field.
2.4 Field of a toroid
A toroid is a solenoid bent into a ring, like a doughnut or a vada. It has N turns in total. Let r be the distance from the centre of the ring.
Take three circular Amperian loops, all centred on the centre of the ring.
Loop in the empty middle (r less than the inner radius): it encloses no current. B = 0.
Loop inside the core: it threads all N turns, each carrying I in the same direction. B × 2πr = μ₀NI.
Loop outside the toroid: each turn crosses this flat disc twice, once going in and once coming out. Net current is zero, so B = 0.
For a thin toroid (core thickness much less than r), 2πr is the mean length, and N/(2πr) = n. So B = μ₀nI, the same as a long solenoid.
| Device | Field inside | Field outside | Uniform? |
|---|---|---|---|
| Long solenoid | μ₀nI (centre), μ₀nI/2 (ends) | about 0 | Yes, away from the ends |
| Toroid | μ₀NI/(2πr) | 0 (both the hole and the outside) | Varies slightly with r |
2.5 Worked examples
Worked example 2.1: A solenoid 50 cm long has 500 turns and carries 2 A. Find B inside it.
Solution: n = 500/0.5 = 1000 m⁻¹. B = μ₀nI = 4π × 10⁻⁷ × 1000 × 2 ≈ 2.51 × 10⁻³ T.
Worked example 2.2: A closed loop encloses three long wires carrying 5 A upward, 3 A downward and 2 A upward. A fourth wire carrying 7 A lies outside the loop. Going round the loop anticlockwise as seen from above, find the line integral of B.
Solution: Only enclosed currents count. With anticlockwise travel seen from above, upward currents are positive. I_enc = 5 − 3 + 2 = 4 A. Line integral = μ₀ × 4 = 4 × 4π × 10⁻⁷ ≈ 5.03 × 10⁻⁶ T m.
Worked example 2.3: A solid copper wire of radius 2 mm carries 10 A uniformly. Find B at 1 mm, 2 mm and 4 mm from the axis.
Solution: At r = 1 mm (inside): B = μ₀Ir/(2πR²) = 2 × 10⁻⁷ × 10 × 10⁻³/(4 × 10⁻⁶) = 5 × 10⁻⁴ T. At r = 2 mm (surface): B = 2 × 10⁻⁷ × 10/(2 × 10⁻³) = 1 × 10⁻³ T. At r = 4 mm (outside): B = 5 × 10⁻⁴ T. Note that R/2 and 2R give the same field.
Worked example 2.4: A toroid has 3000 turns, mean radius 15 cm and carries 1.5 A. Find B in its core and at its centre.
Solution: In the core, B = μ₀NI/(2πr) = 2 × 10⁻⁷ × 3000 × 1.5/0.15 = 6 × 10⁻³ T. At the centre of the ring (in the empty hole), B = 0.
Worked example 2.5: The field at the centre of a long solenoid is 4 mT. What is the field at one of its ends? What is it at the centre if the current is halved and the turns per metre doubled?
Solution: At an end, B = 4/2 = 2 mT. In the second case, nI stays the same, so B at the centre stays 4 mT.
Worked example 2.6: A single-layer solenoid is wound with insulated wire of diameter 0.5 mm, turns touching. It carries 4 A. Find B inside.
Solution: Turns touch, so n = 1/(0.5 × 10⁻³) = 2000 m⁻¹. B = 4π × 10⁻⁷ × 2000 × 4 ≈ 1.0 × 10⁻² T.
Worked example 2.7 (NEET-hard): A long wire of radius R carries total current I, but the current density grows with distance from the axis as J = kr. Find B inside, in terms of I.
Solution: Current inside radius r: I(r) = ∫ kr × 2πr dr from 0 to r = 2πkr³/3. Total current I = 2πkR³/3, so I(r) = I r³/R³. Ampere's law: B × 2πr = μ₀Ir³/R³. So B = μ₀Ir²/(2πR³). The field now grows as r² inside, not r.
Quick revision
Ampere's law: line integral of B around a closed loop = μ₀ × net current enclosed.
Long wire, outside: μ₀I/(2πr). Solid wire, inside: μ₀Ir/(2πR²). Maximum at the surface.
Hollow pipe: zero inside. Coaxial cable: zero outside.
Long solenoid: μ₀nI inside, uniform; μ₀nI/2 at the ends; about zero outside.
Field inside a solenoid does not depend on its radius.
Toroid: μ₀NI/(2πr) in the core; zero in the hole and outside.
NEET traps
Taking n as the total number of turns. In μ₀nI, n is turns per metre.
Saying a current outside the loop gives no field on the loop. It gives a field, but its line integral is zero.
Using μ₀I/(2πr) inside a solid wire. Inside, only the enclosed fraction r²/R² counts.
Assuming the toroid field is non-zero in the central hole. It is zero there.
Forgetting the factor 1/2 at the end of a solenoid.
Practice MCQs: Chapter 2
Level 1: Concept check
1. Ampere's circuital law states that the line integral of B around a closed loop equals (a) μ₀ times the net current enclosed (b) the enclosed current divided by ε₀ (c) μ₀ε₀ times the enclosed current (d) zero for every loop
2. The magnetic field inside a long ideal solenoid is (a) zero (b) varying as 1/r from the axis (c) uniform and along the axis (d) radial
3. The magnetic field outside an ideal toroid is (a) μ₀nI (b) zero (c) μ₀NI/(2πr) (d) half the field inside
4. Inside a long straight solid wire carrying uniform current, B at distance r from the axis is proportional to (a) 1/r (b) 1/r² (c) r⁰ (d) r
5. The field at an end of a long solenoid, compared with the field at its middle, is (a) half (b) equal (c) double (d) zero
6. A long thin-walled metal pipe carries current along its length. The field at a point inside the pipe is (a) μ₀I/(2πr) (b) μ₀I/(2πR) (c) zero (d) μ₀I/(πr)
7. In B = μ₀nI for a solenoid, the unit of n is (a) no unit, it is total turns (b) m⁻¹ (c) m (d) s⁻¹
8. Ampere's law is most convenient for finding B when the current distribution (a) is time-varying (b) is a short straight segment (c) has no symmetry (d) has high symmetry
9. The line integral of B around a closed path that encloses no current is (a) zero (b) μ₀ (c) infinite (d) equal to the field at the centre of the path
10. A long solenoid has 2000 turns per metre and carries 0.5 A. B inside is about (a) 6.28 × 10⁻⁴ T (b) 2.51 × 10⁻³ T (c) 1.26 × 10⁻³ T (d) 1.26 × 10⁻⁴ T
Level 2: NEET standard
11. A solenoid 1 m long with 1000 turns has a field of 6.28 × 10⁻³ T inside. The current is about (a) 2.5 A (b) 5 A (c) 10 A (d) 0.5 A
12. A toroid of 2000 turns and mean radius 10 cm carries 2 A. The field in its core is (a) 4 × 10⁻³ T (b) 1.6 × 10⁻² T (c) 8 × 10⁻⁴ T (d) 8 × 10⁻³ T
13. A long solid wire of radius R carries uniform current. The ratio of the field at R/2 from the axis to the field at 2R from the axis is (a) 1 (b) 2 (c) 1/2 (d) 4
14. A closed loop encloses wires carrying 4 A upward, 6 A downward and 3 A upward. Taking upward as positive, the line integral of B around the loop is (a) 13μ₀ (b) μ₀ (c) 7μ₀ (d) zero
15. The total number of turns of a solenoid is doubled and its length is halved, with the same current. The field inside becomes (a) 2 times (b) unchanged (c) 4 times (d) 1/2 times
16. A toroid's mean radius is doubled, keeping N and I the same. The field in its core (a) doubles (b) stays the same (c) becomes 4 times (d) halves
17. A solid wire of radius 2 mm carries 5 A uniformly. The field 1 mm from its axis is (a) 2.5 × 10⁻⁴ T (b) 5 × 10⁻⁴ T (c) 1.0 × 10⁻³ T (d) 1.25 × 10⁻⁴ T
18. A coaxial cable carries equal and opposite currents in its inner wire and outer sheath. The field just outside the cable is (a) μ₀I/(2πr) (b) 2μ₀I/(2πr) (c) zero (d) μ₀I/(4πr)
19. A single-layer solenoid is wound with wire of diameter 1 mm, turns touching, and carries 2 A. B inside is about (a) 1.26 × 10⁻³ T (b) 2.51 × 10⁻³ T (c) 5.03 × 10⁻³ T (d) 2.51 × 10⁻⁴ T
20. For a long solid wire with uniform current, the graph of B against distance r from the axis (a) is constant inside and zero outside (b) falls as 1/r everywhere (c) is zero inside and falls as 1/r outside (d) rises linearly up to the surface and falls as 1/r outside
21. A solenoid 40 cm long has 400 turns and carries 3 A. B inside is about (a) 3.77 × 10⁻³ T (b) 1.88 × 10⁻³ T (c) 7.54 × 10⁻³ T (d) 3.77 × 10⁻⁴ T
22. A long wire carries 2 A. The line integral of B around a circle of radius 5 cm centred on the wire is about (a) zero (b) 1.26 × 10⁻⁶ T m (c) 5.03 × 10⁻⁶ T m (d) 2.51 × 10⁻⁶ T m
Level 3: Challenge
23. A thick hollow cylinder (inner radius a, outer radius b) carries current I spread uniformly over its metal. The field at distance r, with a less than r less than b, is (a) μ₀I/(2πr) (b) μ₀Ir/(2πb²) (c) μ₀I(r² − a²)/[2πr(b² − a²)] (d) zero
24. A long solid wire of radius R carries uniform current. The field equals half its maximum value at distances from the axis of (a) R/2 only (b) R/2 and 2R (c) 2R only (d) R/4 and 4R
25. A toroid has inner radius 9 cm, outer radius 11 cm, 1100 turns and carries 2 A. The field at 10 cm from the centre is (a) 2.2 × 10⁻³ T (b) 8.8 × 10⁻³ T (c) 4.0 × 10⁻³ T (d) 4.4 × 10⁻³ T
26. A long solenoid gives 2 mT inside. A second long solenoid has twice the radius, the same turns per metre and the same current. Its inside field is (a) 2 mT (b) 4 mT (c) 1 mT (d) 8 mT
27. A long wire of radius R carries total current I with current density J = kr (r measured from the axis). The field inside at distance r is (a) μ₀Ir/(2πR²) (b) μ₀Ir²/(2πR³) (c) μ₀I/(2πr) (d) μ₀Ir²/(πR³)
28. A coaxial cable has an inner wire of radius 1 mm carrying 10 A and a thin outer sheath of radius 5 mm carrying 10 A back. The field 2 mm from the axis is (a) zero (b) 2 × 10⁻³ T (c) 1 × 10⁻³ T (d) 5 × 10⁻⁴ T
29. Assertion (A): Ampere's law gives the field of a short straight current-carrying wire easily. Reason (R): Ampere's law holds for every closed loop around steady currents. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true
30. Statement I: The magnetic field well inside a long solenoid is uniform. Statement II: The field at the end of a long solenoid equals the field at its centre. (a) Both true (b) Both false (c) I true, II false (d) I false, II true
Answer key with reasons
| Q | Ans | Reason |
|---|---|---|
| 1 | a | Line integral = μ₀I_enc. |
| 2 | c | Ideal solenoid has a uniform axial field inside. |
| 3 | b | Net enclosed current outside the toroid is zero. |
| 4 | d | B = μ₀Ir/(2πR²), linear in r. |
| 5 | a | B_end = μ₀nI/2. |
| 6 | c | A loop inside the pipe encloses no current. |
| 7 | b | n is turns per metre. |
| 8 | d | Symmetry lets B come out of the integral. |
| 9 | a | I_enc = 0. |
| 10 | c | 4π × 10⁻⁷ × 2000 × 0.5 = 1.26 × 10⁻³ T. |
| 11 | b | I = B/(μ₀n) = 6.28 × 10⁻³/(1.257 × 10⁻³) ≈ 5 A. |
| 12 | d | 2 × 10⁻⁷ × 2000 × 2/0.1 = 8 × 10⁻³ T. |
| 13 | a | Both equal μ₀I/(4πR). |
| 14 | b | I_enc = 4 − 6 + 3 = 1 A. |
| 15 | c | n = N/L becomes 2/(1/2) = 4 times. |
| 16 | d | B is proportional to 1/r. |
| 17 | a | 2 × 10⁻⁷ × 5 × 10⁻³/(4 × 10⁻⁶) = 2.5 × 10⁻⁴ T. |
| 18 | c | Net enclosed current is zero. |
| 19 | b | n = 1000 m⁻¹; B = 4π × 10⁻⁷ × 1000 × 2. |
| 20 | d | Linear inside, 1/r outside, peak at the surface. |
| 21 | a | n = 1000 m⁻¹; B = 4π × 10⁻⁷ × 1000 × 3. |
| 22 | d | μ₀I = 2.51 × 10⁻⁶ T m, any radius. |
| 23 | c | Enclosed fraction is (r² − a²)/(b² − a²). |
| 24 | b | Linear inside gives R/2; 1/r outside gives 2R. |
| 25 | d | 2 × 10⁻⁷ × 1100 × 2/0.1 = 4.4 × 10⁻³ T. |
| 26 | a | μ₀nI has no radius term. |
| 27 | b | I(r) = Ir³/R³, so B = μ₀Ir²/(2πR³). |
| 28 | c | Only the inner 10 A is enclosed: 2 × 10⁻⁷ × 10/0.002. |
| 29 | d | A short wire lacks the symmetry needed, though the law itself always holds. |
| 30 | c | End field is half the centre field. |
Chapter 2 revision sheet
One-page summary
Ampere's circuital law: the line integral of B round any closed loop = μ₀ × net current threading the loop.
Sign rule: curl right-hand fingers along the loop; currents along the thumb count positive.
Currents outside the loop change B on the loop but not the value of the integral.
The law is always true, but it gives B easily only when symmetry makes B constant along the loop.
Long wire, outside (r ≥ a): B = μ₀I/(2πr).
Solid wire with uniform current, inside (r ≤ a): B = μ₀Ir/(2πa²), largest at the surface, zero on the axis.
Thin hollow pipe: B = 0 inside, μ₀I/(2πr) outside, a jump at the wall.
Thick pipe (a to b): I_enc = I(r² − a²)/(b² − a²) in the metal.
Coaxial cable: field only between inner wire and outer shell; zero outside.
Ideal long solenoid: B = μ₀nI inside, uniform, along the axis; nearly zero outside.
At the ends of a long solenoid on the axis: B = μ₀nI/2.
n = turns per metre; changing radius alone does not change B.
Toroid: B = μ₀NI/(2πr) in the core; zero in the hole and outside.
With a core of relative permeability μᵣ: B = μ₀μᵣnI.
Must-remember table
| Arrangement | Region | B |
|---|---|---|
| Solid wire, radius a | r less than a | μ₀Ir/(2πa²) |
| Solid wire, radius a | r greater than a | μ₀I/(2πr) |
| Thin hollow pipe | inside | 0 |
| Coaxial cable | outside both | 0 |
| Long solenoid | inside, middle | μ₀nI |
| Long solenoid | end, on axis | μ₀nI/2 |
| Toroid, N turns | inside core, radius r | μ₀NI/(2πr) |
| Toroid | hole and outside | 0 |
Memory aids
"Loop In, Current In": only current that pierces the loop counts.
"Rise then Fall": for a solid wire, B rises as r inside and falls as 1/r outside, peaking at the surface.
"Half at the ends": a long solenoid's end field is half its centre field, because the other half of the solenoid is missing.
"Toroid hides its field": a toroid keeps all its field inside the core; hole and outside are both zero.
Concept connections
Ampere's law plays the role of Gauss's law from Physics Book 11: Electrostatics, with symmetry doing the work.
The solenoid field μ₀nI feeds self-inductance L = μ₀n²Al in Physics Book 14: Electromagnetic Induction and Alternating Currents.
Maxwell's displacement-current correction to this law appears in Physics Book 15: Electromagnetic Waves.
Practice MCQs: Chapter 2, Level 4 (new NEET pattern)
31. Match the region with the magnetic field there.
List I:
A. Inside an ideal long solenoid
B. At one end of a long solenoid, on its axis
C. Inside the cavity of a long thin pipe carrying current along its length
D. Inside the core of a toroid at radius r
List II:
(i) μ₀nI/2
(ii) μ₀NI/(2πr)
(iii) μ₀nI
(iv) zero
(a) A-i, B-iii, C-iv, D-ii (b) A-iii, B-i, C-iv, D-ii (c) A-iii, B-iv, C-i, D-ii (d) A-ii, B-i, C-iv, D-iii
32. A long solid wire of radius a carries a uniform current I. Let B₀ = μ₀I/(2πa). Match the distance from the axis with the field.
List I:
A. r = 0
B. r = a/2
C. r = a
D. r = 4a
List II:
(i) B₀/4
(ii) B₀
(iii) zero
(iv) B₀/2
(a) A-iii, B-ii, C-iv, D-i (b) A-iv, B-iii, C-ii, D-i (c) A-iii, B-iv, C-i, D-ii (d) A-iii, B-iv, C-ii, D-i
33. Three long wires pierce the page: 3 A out of the page, 5 A into the page and 2 A out of the page. An anticlockwise Amperian loop counts out-of-page current as positive. Match the loop with the value of the line integral of B.
List I:
A. Loop encloses the 3 A wire only
B. Loop encloses the 3 A and 5 A wires
C. Loop encloses all three wires
D. Loop encloses the 5 A and 2 A wires
List II:
(i) 0
(ii) −3μ₀
(iii) 3μ₀
(iv) −2μ₀
(a) A-iii, B-iv, C-i, D-ii (b) A-iv, B-iii, C-i, D-ii (c) A-iii, B-ii, C-i, D-iv (d) A-i, B-iv, C-iii, D-ii
34. Match the change with its effect on B inside an ideal long solenoid.
List I:
A. Double the turns per metre, same current
B. Double the length, same total turns and current
C. Double the radius, same n and current
D. Fill with a core of μᵣ = 100
List II:
(i) unchanged
(ii) doubles
(iii) becomes 100 times
(iv) halves
(a) A-ii, B-i, C-iv, D-iii (b) A-iv, B-ii, C-i, D-iii (c) A-ii, B-iv, C-i, D-iii (d) A-iii, B-iv, C-i, D-ii
35. How many of the following statements are correct?
A. Ampere's law holds for any closed loop, but it gives B easily only with symmetry.
B. Currents outside the loop add to B on the loop but not to the line integral.
C. The field outside an ideal toroid is zero.
D. Inside a long solid wire with uniform current, B is largest on the axis.
E. Inside an ideal long solenoid, B is the same at all points of a cross-section.
(a) 1 (b) 2 (c) 3 (d) 4
36. A coaxial cable has an inner wire of radius a carrying I and a thin outer shell of radius b carrying I back. Choose the correct set of statements.
A. For a less than r less than b, B = μ₀I/(2πr).
B. For r greater than b, B = 0.
C. Inside the inner wire, B ∝ r.
D. Just outside the outer shell, B = μ₀I/(πb).
(a) A, B and C only (b) A and B only (c) B and D only (d) A, C and D only
37. Choose the correct set of statements.
A. Across the core of a toroid, B varies as 1/r.
B. On the axis at the end of a long solenoid, B is half the central value.
C. An ideal toroid has no field in its central hole.
D. Doubling the current in a toroid doubles the field outside it.
(a) A and B only (b) B and C only (c) A, B and C only (d) A, B, C and D
38. How many of the following statements about the line integral of B round a closed loop are correct?
A. Its SI unit is T m.
B. For the same enclosed current, its value depends on the shape of the loop.
C. It is zero for a loop enclosing equal and opposite currents.
D. It equals μ₀ times the net current threading the loop.
(a) 2 (b) 3 (c) 4 (d) 1
39. A long thin-walled pipe of radius R carries current I along its length. The graph of B against distance r from the axis is (a) a linear rise from 0 to R, then a 1/r fall (b) constant inside, then a 1/r fall (c) zero everywhere (d) zero for r less than R, a jump to μ₀I/(2πR) at r = R, then a 1/r fall
40. A long solid wire of radius 2 cm carries a uniform current. Measured fields: r = 1 cm gives 50 μT; r = 2 cm gives 100 μT. The field at r = 4 cm is (a) 50 μT (b) 25 μT (c) 100 μT (d) 200 μT
41. The field on the axis of a finite but long solenoid is plotted from far outside one end to far outside the other. The graph shows (a) peaks at the two ends (b) a flat plateau at μ₀nI in the middle, about μ₀nI/2 at each end, falling towards zero outside (c) a linear rise from one end to the other (d) zero inside
Case for Q42–43: A physics teacher winds 800 turns uniformly on a plastic tube 40 cm long and 2 cm in radius. She passes 2.5 A through it and uses a Hall probe to measure the field on the axis.
42. The field near the middle of the solenoid is about (a) 3.14 mT (b) 12.6 mT (c) 6.28 mT (d) 0.628 mT
43. The field at one end, on the axis, is about (a) 3.14 mT (b) 6.28 mT (c) 1.57 mT (d) zero
44. A thick hollow cylinder has inner radius a and outer radius 2a. It carries current I spread uniformly through the metal. The field at r = 1.5a is (a) μ₀I/(3πa) (b) 5μ₀I/(18πa) (c) μ₀I/(2πa) (d) 5μ₀I/(36πa)
45. A toroid of 500 turns has inner radius 10 cm and outer radius 12 cm. It carries 3 A. The field at the inner edge of the core, and the ratio B_inner/B_outer, are (a) 3.0 mT, 0.83 (b) 3.0 mT, 1.2 (c) 2.5 mT, 1.2 (d) 2.73 mT, 1.0
Level 4 answer key
| Q | Ans | Reason |
|---|---|---|
| 31 | b | μ₀nI inside, half at the end, zero in pipe, μ₀NI/2πr in toroid |
| 32 | d | B = B₀r/a inside, B₀a/r outside |
| 33 | a | Net enclosed currents: +3, −2, 0, −3 A |
| 34 | c | B = μ₀(N/l)Iμᵣ; radius does not appear |
| 35 | d | Only D false: B is zero on the axis |
| 36 | a | D false: outside the cable B = 0 |
| 37 | c | D false: outside field stays zero |
| 38 | b | B false: only enclosed current matters |
| 39 | d | No current enclosed inside; all of I enclosed outside |
| 40 | a | Surface 100 μT; outside B ∝ 1/r, so half at twice the radius |
| 41 | b | Uniform middle, half value at ends |
| 42 | c | n = 2000 /m; B = 4π × 10⁻⁷ × 2000 × 2.5 = 6.28 mT |
| 43 | a | End field = half = 3.14 mT |
| 44 | d | I_enc = I(2.25 − 1)/3 = 5I/12; B = μ₀(5I/12)/(3πa) |
| 45 | b | B = 2 × 10⁻⁷ × 1500/0.10 = 3.0 mT; ratio 12/10 = 1.2 |