Chapter 7 of 11 · 24 min read

Chapter 5: Torque on a Current Loop and the Moving Coil Galvanometer

A current loop in a uniform field feels no net force, but it does feel a torque that turns it. That torque, balanced by a spring, is how a moving coil galvanometer measures current, and with one added resistor it becomes an ammeter or a voltmeter.

What you will learn

  • The magnetic moment of a current loop, m = NIA.

  • The torque on a loop in a uniform field, τ = m × B.

  • How a moving coil galvanometer works and why it uses a radial field.

  • Current sensitivity and voltage sensitivity.

  • Converting a galvanometer into an ammeter (shunt) and a voltmeter (series resistance).

5.1 Magnetic moment of a current loop

A flat loop of area A carrying current I has a magnetic dipole moment:

m⃗=NIA⃗\vec{m} = N I \vec{A}

N is the number of turns. The vector A has size equal to the area and points along the normal to the loop. Its direction comes from the right-hand rule: curl the fingers along the current, and the thumb gives m.

The SI unit of m is A m² (equivalently J/T). The loop behaves like a tiny bar magnet with its north pole on the side m points to. Chapter 6 develops this.

5.2 Torque on a rectangular loop in a uniform field

Take a rectangular loop PQRS with sides a (PQ and RS) and b (QR and SP). It carries current I in a uniform field B. Let the loop be free to turn about an axis through the middle of sides QR and SP, with B perpendicular to that axis. Let θ be the angle between the normal to the loop (that is, m) and B.

Forces on the sides.

  • Sides QR and SP (length b) are perpendicular to the turning axis. They feel equal and opposite forces directed along the axis, acting on the same line. These cancel and cause no torque.

  • Sides PQ and RS (length a) are always perpendicular to B. Each feels force F = IaB. The two forces are equal, opposite and parallel, but not along the same line. They form a couple.

Torque. The perpendicular distance between the lines of the two forces is b sin θ. So:

τ=F (bsin⁡θ)=IaB bsin⁡θ=IABsin⁡θ\tau = F\,(b\sin\theta) = IaB\,b\sin\theta = IAB\sin\theta

For N turns, and in vector form:

τ=NIABsin⁡θ,τ⃗=m⃗×B⃗\tau = NIAB\sin\theta,\qquad \vec{\tau} = \vec{m}\times\vec{B}

This holds for a flat loop of any shape in a uniform field.

PositionAngle θ between m and BTorqueRemark
Plane of loop perpendicular to B0°0Stable equilibrium
Plane of loop parallel to B90°NIAB, maximumCoil is turned hardest
Plane perpendicular to B, m opposite to B180°0Unstable equilibrium

The torque always tries to turn m into line with B. An electric motor uses this torque, with a commutator flipping the current every half turn to keep it turning one way.

5.3 The moving coil galvanometer

A galvanometer detects and measures small currents, of the order of microamperes to milliamperes.

Construction.

  1. A rectangular coil of many turns of fine insulated copper wire, wound on a light frame.

  2. A strong permanent magnet with concave (curved) pole pieces.

  3. A soft iron cylinder fixed inside the coil.

  4. The coil turns about a fixed axis, held by a phosphor-bronze suspension wire or a pair of hair-springs. These give a restoring torque.

  5. A pointer on a scale (or a mirror and lamp-and-scale) shows the deflection.

Radial field. The concave poles and the soft iron core make the field radial in the gap. Wherever the coil turns, its plane stays along the field lines. So θ = 90° at every position, and the deflecting torque is always NIAB, the maximum value. The soft iron core also concentrates the field and makes it stronger.

Figure 5.1 · Coil of a moving coil galvanometer in a radial field
Figure 5.1 · Coil of a moving coil galvanometer in a radial field

The curved pole pieces and the iron core make every field line in the gap point along a radius, so the coil sides always cut the field at right angles and the couple on them stays NIAB.

Working. The coil turns until the spring's restoring torque kφ balances the magnetic torque. Here φ is the deflection and k is the torsion constant (torque per radian of twist).

NIAB=kφ  ⇒  φ=(NABk)INIAB = k\varphi \;\Rightarrow\; \varphi = \left(\frac{NAB}{k}\right) I

The deflection is proportional to the current. So the scale is linear, with evenly spaced marks. That is the main reason for using a radial field.

The quantity k/(NAB) is called the galvanometer constant (current per unit deflection).

5.4 Sensitivity of a galvanometer

Current sensitivity is the deflection per unit current:

Is=φI=NABkI_s = \frac{\varphi}{I} = \frac{NAB}{k}

Voltage sensitivity is the deflection per unit voltage across the coil. With coil resistance G, V = IG:

Vs=φV=NABkGV_s = \frac{\varphi}{V} = \frac{NAB}{kG}

Ways to raise current sensitivity: more turns N, larger area A, stronger field B, and a weaker suspension (smaller k). Phosphor bronze is used because it has a small k and high tensile strength, and it returns to zero without lasting twist.

A common NEET question: double the number of turns. Current sensitivity doubles. But the wire is twice as long, so G doubles too. Voltage sensitivity therefore stays the same.

5.5 Converting a galvanometer into an ammeter

A galvanometer has full-scale current I_g (small) and resistance G. To measure a larger current I, connect a small resistance S, called a shunt, in parallel with it. Most of the current bypasses the coil through S.

The voltage across G and S is the same:

IgG=(I−Ig) S  ⇒  S=Ig GI−IgI_g G = (I - I_g)\,S \;\Rightarrow\; S = \frac{I_g\,G}{I - I_g}

If the range is to be n times the galvanometer's own range (I = nI_g):

S=Gn−1S = \frac{G}{n-1}

The resistance of the ammeter is GS/(G + S), which is less than S. An ammeter is joined in series in a circuit, and it should disturb the current as little as possible. An ideal ammeter has zero resistance.

5.6 Converting a galvanometer into a voltmeter

To measure a potential difference up to V, connect a large resistance R in series with the galvanometer. At full scale, the current through it is I_g:

V=Ig (G+R)  ⇒  R=VIg−GV = I_g\,(G + R) \;\Rightarrow\; R = \frac{V}{I_g} - G

For a range n times the galvanometer's own full-scale voltage (I_gG):

R=(n−1) GR = (n-1)\,G

The voltmeter's resistance is G + R, which is large. A voltmeter is joined in parallel, and it should draw as little current as possible. An ideal voltmeter has infinite resistance.

Figure 5.2 · Converting a galvanometer into an ammeter and a voltmeter
Figure 5.2 · Converting a galvanometer into an ammeter and a voltmeter

In the ammeter, most of the current I bypasses the coil through the small shunt S and only I_g flows through G; in the voltmeter, the large series R limits the current to I_g at the full-scale voltage V.

FeatureAmmeterVoltmeter
Extra resistanceSmall shunt SLarge resistance R
How it is joined to the galvanometerIn parallelIn series
How the meter is joined in a circuitIn seriesIn parallel
FormulaS = I_gG/(I − I_g)R = V/I_g − G
Resistance of the meterVery low, less than SVery high, G + R
Ideal valueZeroInfinite

5.7 Worked examples

Worked example 5.1: A coil of 100 turns and area 20 cm² carries 0.5 A in a field of 0.2 T. Its normal makes 30° with the field. Find the torque.

Solution: τ = NIAB sin θ = 100 × 0.5 × 2 × 10⁻³ × 0.2 × 0.5 = 0.01 N m.

Worked example 5.2: A circular coil of 50 turns and radius 5 cm carries 2 A in a field of 0.4 T. Find the maximum torque.

Solution: A = πr² = π × 0.0025 m². τ_max = NIAB = 50 × 2 × 0.00785 × 0.4 ≈ 0.314 N m. It occurs when the plane of the coil is parallel to B.

Worked example 5.3: A galvanometer coil has 200 turns of area 10 cm² in a radial field of 0.5 T. The torsion constant is 2 × 10⁻⁴ N m/rad. Find its current sensitivity and the deflection for 1 mA.

Solution: I_s = NAB/k = 200 × 10⁻³ × 0.5/(2 × 10⁻⁴) = 500 rad/A. For 1 mA, φ = 500 × 10⁻³ = 0.5 rad, about 29°.

Worked example 5.4: A galvanometer of resistance 50 Ω gives full-scale deflection at 5 mA. Convert it into an ammeter of range 0 to 5 A.

Solution: S = I_gG/(I − I_g) = (0.005 × 50)/(4.995) ≈ 0.050 Ω, joined in parallel.

Worked example 5.5: Convert the same galvanometer into a voltmeter of range 0 to 10 V.

Solution: R = V/I_g − G = 10/0.005 − 50 = 2000 − 50 = 1950 Ω, joined in series.

Worked example 5.6: The number of turns of a galvanometer coil is doubled, keeping the area, field and suspension the same. What happens to its current and voltage sensitivities?

Solution: I_s = NAB/k doubles. The wire length doubles, so G doubles. V_s = NAB/(kG) stays the same.

Worked example 5.7: A galvanometer of resistance 99 Ω is shunted by 1 Ω. What fraction of the main current passes through the galvanometer?

Solution: Current divides inversely as resistance. I_g/I = S/(G + S) = 1/100. So 1% passes through the coil, and the range becomes 100 times.

Worked example 5.8 (NEET-hard): With a series resistance R₁, a galvanometer reads up to V volts. With R₂ in place of R₁, it reads up to 2V. Find the galvanometer resistance G.

Solution: V = I_g(G + R₁) and 2V = I_g(G + R₂). Divide: 2(G + R₁) = G + R₂. So G = R₂ − 2R₁. Check with Example 5.5: R₁ = 1950 Ω for 10 V and R₂ = 3950 Ω for 20 V give G = 50 Ω.

Quick revision

  • m = NIA, along the normal by the right-hand rule; unit A m².

  • τ = m × B, magnitude NIAB sin θ; maximum when the plane of the coil is parallel to B.

  • Net force on the loop in a uniform field is zero; only torque acts.

  • Galvanometer: radial field gives NIAB = kφ, a linear scale.

  • Current sensitivity NAB/k; voltage sensitivity NAB/(kG).

  • Ammeter: shunt S = I_gG/(I − I_g) in parallel; S = G/(n − 1).

  • Voltmeter: R = V/I_g − G in series; R = (n − 1)G.

NEET traps

  • Taking θ as the angle between the plane of the coil and B. In τ = NIAB sin θ, θ is between the normal (m) and B. If the plane makes angle α with B, use cos α.

  • Saying doubling N doubles voltage sensitivity. It does not, because G doubles too.

  • Joining the shunt in series or the voltmeter resistance in parallel.

  • Forgetting to subtract G when finding the series resistance for a voltmeter.

  • Thinking the radial field is there to increase torque. Its main job is to keep the torque NIAB at every angle, so the scale is linear.

Practice MCQs: Chapter 5

Level 1: Concept check

1. The torque on a current loop of magnetic moment m in a uniform field B is (a) m · B (b) m × B (c) B × m (d) mB cos θ

2. The magnetic moment of a coil of N turns, area A and current I is (a) NIA (b) NIA² (c) NI/A (d) IA/N

3. The SI unit of magnetic dipole moment is (a) A m (b) T m² (c) A m² (d) N/A

4. A moving coil galvanometer uses a radial magnetic field so that (a) the coil carries more current (b) the field becomes weaker (c) the coil does not heat up (d) the torque stays NIAB at all deflections, giving a linear scale

5. A galvanometer is converted into an ammeter by connecting (a) a low resistance in parallel (b) a high resistance in parallel (c) a high resistance in series (d) a low resistance in series

6. A galvanometer is converted into a voltmeter by connecting (a) a low resistance in parallel (b) a high resistance in parallel (c) a high resistance in series (d) a low resistance in series

7. The resistance of an ideal ammeter is (a) infinite (b) zero (c) equal to that of the galvanometer (d) 1 Ω

8. The torque on a current loop in a uniform field is maximum when the plane of the loop is (a) perpendicular to B (b) at 45° to B (c) at 60° to B (d) parallel to B

9. The current sensitivity of a galvanometer is (a) deflection per unit current (b) current per unit deflection (c) deflection per unit voltage (d) resistance per unit current

10. The soft iron cylinder inside a galvanometer coil (a) reduces the resistance of the coil (b) provides the restoring torque (c) makes the field radial and stronger (d) acts as the pointer

Level 2: NEET standard

11. A coil of 100 turns and area 20 cm² carries 0.5 A in a field of 0.2 T, its normal at 30° to the field. The torque on it is (a) 0.017 N m (b) 0.02 N m (c) 0.01 N m (d) 0.005 N m

12. A circular coil of 50 turns and radius 5 cm carries 2 A in a field of 0.4 T. The maximum torque on it is about (a) 0.157 N m (b) 0.314 N m (c) 0.628 N m (d) 3.14 N m

13. A galvanometer of 50 Ω gives full scale at 5 mA. The shunt needed for a 0 to 5 A ammeter is about (a) 0.5 Ω (b) 0.005 Ω (c) 5 Ω (d) 0.05 Ω

14. The same galvanometer is to read 0 to 10 V. The series resistance needed is (a) 2000 Ω (b) 1950 Ω (c) 2050 Ω (d) 195 Ω

15. To make the range of an ammeter n times that of a galvanometer of resistance G, the shunt is (a) G/(n − 1) (b) (n − 1)G (c) G/n (d) nG

16. A galvanometer of 100 Ω is to carry only 10% of the main current. The shunt needed is about (a) 10 Ω (b) 90 Ω (c) 11.1 Ω (d) 9 Ω

17. The number of turns of a galvanometer coil is doubled (its resistance also doubles). Then (a) both sensitivities double (b) both sensitivities stay the same (c) current sensitivity is unchanged, voltage sensitivity doubles (d) current sensitivity doubles, voltage sensitivity is unchanged

18. A wire of fixed length forms a single square loop, and is then reshaped into a single circular loop. With the same current and field, the ratio of maximum torques, circle to square, is (a) π/4 (b) 4/π (c) 1 (d) 2

19. A coil of 10 turns and area 0.01 m² carries 2 A in a field of 0.5 T. The work needed to turn it from the stable position to the unstable position is (a) 0.1 J (b) 0.4 J (c) zero (d) 0.2 J

20. A galvanometer of 50 Ω with 1950 Ω in series reads up to 10 V. The additional series resistance needed to read up to 20 V is (a) 2000 Ω (b) 1950 Ω (c) 3950 Ω (d) 4000 Ω

21. A galvanometer coil has 200 turns of area 10 cm² in a radial field of 0.5 T, with torsion constant 2 × 10⁻⁴ N m/rad. The deflection for 1 mA is (a) 0.05 rad (b) 0.5 rad (c) 5 rad (d) 0.25 rad

22. The galvanometer of Q21 has resistance 50 Ω. Its voltage sensitivity is (a) 10 rad/V (b) 25 000 rad/V (c) 0.1 rad/V (d) 1 rad/V

Level 3: Challenge

23. A galvanometer reads up to V with series resistance R₁ and up to 2V with series resistance R₂. Its resistance is (a) R₂ − R₁ (b) (R₂ − R₁)/2 (c) R₂ − 2R₁ (d) 2R₁ − R₂

24. A galvanometer of 99 Ω is shunted by 1 Ω. The fraction of the main current through the galvanometer is (a) 1% (b) 99% (c) 10% (d) 0.1%

25. A square loop of side a carries current I in a uniform field B that lies in the plane of the loop, along one diagonal. The torque on the loop is (a) Ia²B/√2 (b) Ia²B (c) zero (d) √2 Ia²B

26. A wire of length L carries current I and is wound into a circular coil. In a field B, the largest possible maximum torque, over all choices of the number of turns, is (a) IL²B/(4π) (b) IL²B/(2π) (c) IL²B/π (d) IL²B/(4π²)

27. A galvanometer of 20 Ω gives full scale at 10 mA. It is converted into an ammeter of range 0 to 1 A. The resistance of the ammeter is about (a) 20 Ω (b) 0.02 Ω (c) 2 Ω (d) 0.2 Ω

28. A galvanometer in a circuit shows 30° deflection. A shunt equal to its own resistance is now connected across it, and the main current is kept the same. The new deflection is (a) 30° (b) 60° (c) 15° (d) 7.5°

29. Assertion (A): The scale of a moving coil galvanometer is linear. Reason (R): In a radial field, the plane of the coil stays along the field at every deflection, so the deflecting torque is always NIAB. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: An ammeter is joined in series in a circuit and has a low resistance. Statement II: A voltmeter is a galvanometer with a low resistance joined in parallel. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1bτ = m × B.
2am = NIA.
3cCurrent × area.
4dRadial field keeps sin θ = 1, so φ is proportional to I.
5aA shunt in parallel carries the extra current.
6cA large series resistance limits the current.
7bIt should not change the circuit current.
8dThen m is perpendicular to B, sin 90° = 1.
9aI_s = φ/I.
10cIt shapes and strengthens the field.
11c100 × 0.5 × 0.002 × 0.2 × 0.5 = 0.01 N m.
12b50 × 2 × π(0.05)² × 0.4 ≈ 0.314 N m.
13d0.25/4.995 ≈ 0.05 Ω.
14b10/0.005 − 50 = 1950 Ω.
15aI_gG = (n − 1)I_gS.
16cS/(G + S) = 0.1 gives S = G/9.
17dI_s doubles; V_s = I_s/G is unchanged.
18bAreas L²/(4π) and L²/16; ratio 4/π.
19dW = 2mB = 2 × (10 × 2 × 0.01) × 0.5 = 0.2 J.
20aTotal 20/0.005 = 4000 Ω; extra = 4000 − 2000.
21bI_s = 500 rad/A; × 10⁻³ A.
22aV_s = I_s/G = 500/50.
23c2(G + R₁) = G + R₂.
24aS/(G + S) = 1/100.
25bm is perpendicular to B, so τ = IAB = Ia²B.
26am = IL²/(4πN), largest for N = 1.
27dS = 0.2/0.99 ≈ 0.202 Ω; parallel with 20 Ω gives about 0.2 Ω.
28cCurrent through the coil halves, so deflection halves.
29aR is exactly why the scale is linear.
30cA voltmeter uses a high resistance in series.

Chapter 5 revision sheet

One-page summary

  • Magnetic moment of a flat loop: m = NIA, perpendicular to its plane; unit A m² = J/T.

  • Direction of m: curl right-hand fingers along the current; the thumb gives m.

  • Torque in uniform B: τ = m × B, magnitude NIAB sin θ (θ between m and B, the normal).

  • Torque is largest when the plane of the coil is parallel to B; zero when the plane is perpendicular to B.

  • Net force on the loop in a uniform field is zero; only torque acts.

  • The torque formula holds for any flat shape; only the area matters.

  • MCG: coil in a radial field from concave poles and a soft-iron core, so θ = 90° at every deflection.

  • Balance: NIAB = kφ, so φ ∝ I and the scale is linear.

  • Current sensitivity I_s = φ/I = NAB/k. Voltage sensitivity V_s = φ/V = NAB/(kG).

  • Doubling N doubles I_s but also roughly doubles G, so V_s may not change.

  • Ammeter: low shunt S = I_gG/(I − I_g) in parallel; connected in series in the circuit.

  • Voltmeter: high resistance R = V/I_g − G in series with G; connected in parallel.

  • Ideal ammeter has zero resistance; ideal voltmeter has infinite resistance.

  • Range multiplied n times: S = G/(n − 1) or R = (n − 1)G.

Must-remember table

QuantityFormulaUnit
Magnetic momentNIAA m²
Torque on coilNIAB sin θN m
Current sensitivityNAB/krad/A (div/A)
Voltage sensitivityNAB/(kG)rad/V (div/V)
Shunt for range II_gG/(I − I_g)Ω
Series R for range VV/I_g − GΩ
Ammeter resistanceGS/(G + S)Ω
Voltmeter resistanceG + RΩ

Memory aids

  • "SAP" for the ammeter: Shunt, Ammeter, Parallel (small resistance in parallel).

  • "VHS" for the voltmeter: Voltmeter, High resistance, Series.

  • "NAB the k": current sensitivity is NAB over k; divide by G for voltage sensitivity.

  • "Flat to the field, full force turn": coil plane parallel to B gives maximum torque.

Concept connections

  • Shunts and series resistors use the parallel and series rules of Physics Book 12: Current Electricity.

  • τ = m × B mirrors τ = p × E of the electric dipole in Physics Book 11: Electrostatics.

  • Torque and rotational equilibrium (kφ balance) come from Physics Book 5: Rotational Motion.

Practice MCQs: Chapter 5, Level 4 (new NEET pattern)

31. Match each quantity with its formula (coil of N turns, area A, spring constant k, resistance G).

List I:

  • A. Magnetic moment

  • B. Torque in uniform B

  • C. Current sensitivity

  • D. Voltage sensitivity

List II:

  • (i) NAB/k

  • (ii) NIA

  • (iii) NAB/(kG)

  • (iv) NIAB sin θ

(a) A-iv, B-ii, C-i, D-iii (b) A-ii, B-i, C-iv, D-iii (c) A-ii, B-iv, C-i, D-iii (d) A-ii, B-iv, C-iii, D-i

32. A galvanometer has resistance G and full-scale current I_g. Match.

List I:

  • A. Ammeter of range I

  • B. Voltmeter of range V

  • C. Ideal ammeter resistance

  • D. Ideal voltmeter resistance

List II:

  • (i) series R = V/I_g − G

  • (ii) infinite

  • (iii) shunt S = I_gG/(I − I_g) in parallel

  • (iv) zero

(a) A-iii, B-i, C-iv, D-ii (b) A-i, B-iii, C-iv, D-ii (c) A-iii, B-i, C-ii, D-iv (d) A-iv, B-i, C-iii, D-ii

33. A loop of moment m is in a uniform field B. Match the angle between m and B with the torque.

List I:

  • A. 0°

  • B. 90°

  • C. 180°

  • D. 30°

List II:

  • (i) maximum, mB

  • (ii) mB/2

  • (iii) zero, stable

  • (iv) zero, unstable

(a) A-iv, B-i, C-iii, D-ii (b) A-iii, B-ii, C-iv, D-i (c) A-i, B-iii, C-iv, D-ii (d) A-iii, B-i, C-iv, D-ii

34. Match each part of a moving coil galvanometer with its purpose.

List I:

  • A. Concave pole pieces giving a radial field

  • B. Soft-iron cylindrical core

  • C. Phosphor-bronze spring

  • D. Low resistance across the coil

List II:

  • (i) strengthens the field in the gap

  • (ii) gives the restoring torque kφ

  • (iii) lets most of the current bypass the coil

  • (iv) keeps the coil plane along B, so the scale is linear

(a) A-i, B-iv, C-ii, D-iii (b) A-iv, B-i, C-ii, D-iii (c) A-iv, B-ii, C-i, D-iii (d) A-iii, B-i, C-ii, D-iv

35. How many of the following statements are correct?

  • A. For the same area, the torque on a flat loop does not depend on its shape.

  • B. The net force on a current loop in a uniform field is zero.

  • C. Increasing the number of turns always increases voltage sensitivity.

  • D. An ammeter is connected in series.

  • E. A shunt resistance is usually much smaller than G.

(a) 3 (b) 4 (c) 5 (d) 2

36. Choose the correct set of statements.

  • A. A stronger magnet raises current sensitivity.

  • B. A weaker spring (smaller k) raises current sensitivity.

  • C. Voltage sensitivity = current sensitivity / G.

  • D. Doubling both N and G doubles voltage sensitivity.

(a) A and B only (b) B, C and D only (c) A and D only (d) A, B and C only

37. A galvanometer has G = 100 Ω and I_g = 1 mA. Choose the correct set of statements.

  • A. To read up to 1 A, a shunt of about 0.1 Ω is needed.

  • B. To read up to 10 V, a series resistance of 9900 Ω is needed.

  • C. The 1 A ammeter has a resistance of about 0.1 Ω.

  • D. The 10 V voltmeter has a resistance of 9900 Ω.

(a) A and B only (b) A, B, C and D (c) A, B and C only (d) B and D only

38. How many of the following statements about the magnetic moment of a loop are correct?

  • A. Its unit A m² equals J/T.

  • B. Its direction follows the right-hand rule: fingers along the current, thumb along m.

  • C. It doubles when the radius doubles at the same current.

  • D. The torque on it is τ = m × B.

(a) 3 (b) 2 (c) 4 (d) 1

39. For a moving coil galvanometer the table reads: I = 2 mA gives 10 divisions; I = 5 mA gives 25 divisions. The scale has 30 divisions. The full-scale current is (a) 3 mA (b) 5 mA (c) 7.5 mA (d) 6 mA

40. A galvanometer has G = 50 Ω and I_g = 2 mA. The shunt needed for a 0–5 A ammeter is about (a) 0.010 Ω (b) 0.020 Ω (c) 0.050 Ω (d) 0.20 Ω

41. A galvanometer with G = 50 Ω becomes a 0–3 V voltmeter with a series resistance of 2950 Ω. For a 0–15 V range, the series resistance must be (a) 14750 Ω (b) 15000 Ω (c) 14950 Ω (d) 12000 Ω

Case for Q42–43: A school galvanometer has a rectangular coil of 100 turns, 2 cm by 2.5 cm, in a radial field of 0.2 T. Its spring constant is 2 × 10⁻⁵ N m/rad and the coil resistance is 50 Ω.

42. The current sensitivity is (a) 500 rad/A (b) 50 rad/A (c) 5000 rad/A (d) 250 rad/A

43. The deflection when 20 mV is applied across the coil is (a) 0.1 rad (b) 0.4 rad (c) 0.2 rad (d) 1.0 rad

44. A wire of length L carries current I in a uniform field B. It is wound into a flat circular coil. The largest torque the coil can ever experience is (a) IBL²/(2π) (b) IBL²/π (c) IBL²/(8π) (d) IBL²/(4π)

45. A galvanometer of resistance G with shunt S reads up to current I. To read up to 2I, the new shunt must be (a) S/2 (b) GS/(2G + S) (c) 2S (d) GS/(G + 2S)

Level 4 answer key

QAnsReason
31cm = NIA; τ = NIAB sin θ; I_s = NAB/k; V_s = I_s/G
32aShunt in parallel; series R; ideal ammeter 0, voltmeter infinite
33dτ = mB sin θ; 0° stable, 180° unstable
34bRadial field keeps sin θ = 1; core strengthens; spring restores; shunt bypasses
35bOnly C false: G also rises with N
36dD false: V_s = NAB/(kG) unchanged
37cD false: voltmeter resistance = 9900 + 100 = 10000 Ω
38aC false: area × 4, so m × 4
39d5 div/mA, so 30 div needs 6 mA
40bS = 0.002 × 50/(5 − 0.002) = 0.020 Ω
41cI_g = 3/3000 = 1 mA; R = 15/0.001 − 50
42aNAB/k = 100 × 5 × 10⁻⁴ × 0.2/(2 × 10⁻⁵)
43cI = 0.02/50 = 0.4 mA; φ = 500 × 0.0004 = 0.2 rad
44dR = L/2πN gives τ = IBL²/(4πN), largest for N = 1
45bI = I_g(G + S)/S; solve with 2I for S′
24 min left
‹
›