Chapter 9 of 11 · 23 min read

Chapter 7: Magnetic Materials

Every material responds to a magnetic field, but in one of three ways: diamagnetic materials are weakly pushed out of a field, paramagnetic ones are weakly pulled in, and ferromagnetic ones are pulled in strongly. Temperature changes the last two, and the B–H hysteresis loop decides which ferromagnet suits which job.

What you will learn

  • Magnetisation M, magnetic intensity H, susceptibility χ and relative permeability μᵣ.

  • Diamagnetic, paramagnetic and ferromagnetic substances: properties, origin, examples.

  • Curie's law for paramagnets and the Curie temperature of ferromagnets.

  • Domains and the B–H hysteresis loop: retentivity and coercivity.

  • Choosing materials for permanent magnets, electromagnets and transformer cores.

7.1 Magnetisation and magnetic intensity

Magnetisation M is the net magnetic moment per unit volume of a material:

M⃗=m⃗netV\vec{M} = \frac{\vec{m}_{\text{net}}}{V}

Its unit is A m²/m³ = A m⁻¹.

Put a material inside a long solenoid with n turns per metre and current I. The field due to the current alone is B₀ = μ₀nI. The material adds its own field μ₀M. So the total field is:

B=μ0 (H+M),H=nI=B0μ0B = \mu_0\,(H + M),\qquad H = nI = \frac{B_0}{\mu_0}

H is called the magnetic intensity. It depends only on the free current, not on the material. Its unit is also A m⁻¹.

For most materials, M is proportional to H:

M=χHM = \chi H

χ (chi) is the magnetic susceptibility. It is a pure number. Putting this in:

B=μ0(1+χ)H=μ0μrH=μH,μr=1+χB = \mu_0(1+\chi)H = \mu_0\mu_r H = \mu H,\qquad \mu_r = 1+\chi

μᵣ is the relative permeability and μ = μ₀μᵣ is the permeability of the material.

QuantitySymbolUnitMeaning
Magnetic fieldBTTotal field inside the material
Magnetic intensityHA/mPart set by free currents (nI in a solenoid)
MagnetisationMA/mMoment per unit volume of the material
SusceptibilityχnoneM/H
Relative permeabilityμᵣnone1 + χ

7.2 Diamagnetic substances

Behaviour. A diamagnetic material is weakly repelled by a magnet. In a non-uniform field, it moves from the stronger region to the weaker region. A rod of it hung in a uniform field settles perpendicular to the field.

Numbers. χ is small and negative, about −10⁻⁵. So μᵣ is slightly less than 1. Field lines are slightly pushed out of the material.

Origin. The atoms have no net magnetic moment of their own; the electron orbit and spin moments cancel. When a field is applied, the electron orbits adjust and set up a small induced moment opposite to the field (much like Lenz's law). So M points opposite to H.

Temperature. Diamagnetism hardly depends on temperature.

Examples. Bismuth, copper, lead, silicon, gold, water, sodium chloride, nitrogen gas at room conditions.

Every material has this diamagnetic response. In para- and ferromagnetic materials, a stronger effect simply hides it.

Superconductors are perfect diamagnets. Below a critical temperature, they push the field out completely: B = 0 inside, χ = −1, μᵣ = 0. This is the Meissner effect. It lets a magnet float above a cooled superconductor, the idea behind maglev trains.

7.3 Paramagnetic substances

Behaviour. A paramagnetic material is weakly attracted by a magnet. In a non-uniform field, it moves from the weaker region to the stronger region. A rod of it settles parallel to the field.

Numbers. χ is small and positive, about 10⁻⁵ to 10⁻³. μᵣ is slightly more than 1.

Origin. Each atom has a permanent magnetic moment. Without a field, thermal motion keeps the moments pointing randomly, so M = 0. A field lines them up a little, against the jostling of thermal motion.

Temperature: Curie's law. Higher temperature means more jostling and less alignment. Pierre Curie found:

M=C B0Torχ=C μ0TM = C\,\frac{B_0}{T}\qquad\text{or}\qquad \chi = \frac{C\,\mu_0}{T}

C is the Curie constant and T the absolute temperature. In short: χ is inversely proportional to T. Halve the kelvin temperature, and χ doubles.

Curie's law holds for weak fields and ordinary temperatures. At very low temperature and very strong field, almost all moments line up and M reaches a saturation value.

Examples. Aluminium, sodium, calcium, platinum, oxygen gas (and liquid oxygen), copper chloride.

Liquid oxygen poured between the poles of a strong magnet sticks there. Liquid nitrogen, being diamagnetic, just runs through.

7.4 Ferromagnetic substances

Behaviour. Strongly attracted by a magnet. They move readily from weak to strong field regions and can stay magnetised after the field is removed.

Numbers. χ is large and positive, from hundreds to about 10⁵. μᵣ is very large.

Origin: domains. Atomic moments in a ferromagnet line up spontaneously with their neighbours over small regions called domains, each about 1 mm or less across and containing around 10¹⁷ to 10¹⁸ atoms. Each domain is fully magnetised. In an unmagnetised piece, domains point in random directions and cancel. An applied field makes domains along the field grow and others turn. The piece becomes strongly magnetised.

Examples. Iron, cobalt, nickel, gadolinium, and alloys such as alnico and steel.

Temperature: the Curie temperature. Heat disturbs the alignment inside domains. Above a temperature T_c, called the Curie temperature, the domains break up and the material becomes paramagnetic. Above T_c the susceptibility follows the Curie–Weiss law:

χ=CT−Tc(T>Tc)\chi = \frac{C}{T - T_c}\qquad (T > T_c)
MaterialCurie temperature (approx.)
Cobalt1394 K
Iron1043 K
Nickel631 K
Gadolinium293 K

This is why heating a magnet strongly, or hammering it, weakens it. Gadolinium loses its ferromagnetism just above room temperature on a warm day.

7.5 Comparing the three classes

PropertyDiamagneticParamagneticFerromagnetic
Susceptibility χSmall, negative (about −10⁻⁵)Small, positive (10⁻⁵ to 10⁻³)Large, positive (10² to 10⁵)
Relative permeability μᵣSlightly less than 1Slightly more than 1Much greater than 1
In a non-uniform fieldMoves to weaker fieldMoves to stronger fieldMoves to stronger field, strongly
Rod in a uniform fieldSettles perpendicular to BSettles parallel to BSettles parallel to B
Permanent atomic momentNoYes, randomYes, aligned in domains
Effect of temperatureAlmost noneχ proportional to 1/T (Curie law)Becomes paramagnetic above T_c
ExamplesBi, Cu, Pb, water, NaClAl, Na, Pt, O₂Fe, Co, Ni, Gd

A neat test: fill a U-tube with the liquid and place one limb between magnet poles. A paramagnetic liquid rises in that limb; a diamagnetic one falls.

7.6 Hysteresis: the B–H loop

Take an unmagnetised iron sample inside a solenoid. Increase H from zero. B rises along a curve and levels off at saturation, when all domains are aligned.

Now reduce H to zero. B does not come back to zero. The value left over is the retentivity (or remanence), B_r. The iron has become a magnet.

To bring B to zero, you must apply H in the reverse direction. The size of this reverse H is the coercivity, H_c.

Take H to a large reverse value (reverse saturation) and back again. B traces a closed loop. B lags behind H; this lag is called hysteresis.

Figure 7.1 · Schematic B–H hysteresis loops of steel and soft iron
Figure 7.1 · Schematic B–H hysteresis loops of steel and soft iron

When H returns to zero, B stays at the retentivity B_r, and a reverse H equal to the coercivity H_c is needed to wipe it out; steel's wide loop suits permanent magnets, soft iron's narrow loop suits cores.

The area of the loop is the energy lost as heat per unit volume of the material in one cycle of magnetisation. In a transformer running at 50 Hz, the core goes round this loop 50 times a second.

7.7 Choosing a magnetic material

UseNeededBest choiceWhy
Permanent magnetHigh retentivity and high coercivitySteel, alnico, ferrite magnetsStays magnetised and resists demagnetising
Electromagnet coreHigh permeability, low retentivity, low coercivitySoft ironStrong field when on, near zero when off
Transformer, motor and generator coresHigh permeability, thin hysteresis loop (low loss)Soft iron, silicon steelRepeated cycling wastes little energy

Soft iron has a tall, thin loop. Steel has a wider loop with larger coercivity. Soft iron may even have a higher retentivity than steel, but its small coercivity means it loses that magnetism easily.

7.8 Worked examples

Worked example 7.1: A solenoid with 1000 turns per metre carries 2 A. Its core has μᵣ = 400. Find H, B and M.

Solution: H = nI = 2000 A/m. B = μ₀μᵣH = 4π × 10⁻⁷ × 400 × 2000 ≈ 1.0 T. M = (μᵣ − 1)H = 399 × 2000 ≈ 7.98 × 10⁵ A/m. Without the core, B would be only 2.5 mT.

Worked example 7.2: Classify three materials with χ = −2 × 10⁻⁵, χ = 3 × 10⁻⁴ and χ = 800.

Solution: Small negative: diamagnetic. Small positive: paramagnetic. Large positive: ferromagnetic.

Worked example 7.3: A paramagnetic salt has χ = 1.2 × 10⁻⁵ at 300 K. Find χ at 150 K.

Solution: χ is proportional to 1/T. Temperature halves, so χ doubles: 2.4 × 10⁻⁵.

Worked example 7.4: An iron bar of volume 5 cm³ has magnetisation 8 × 10⁵ A/m. Find its magnetic moment.

Solution: m = MV = 8 × 10⁵ × 5 × 10⁻⁶ = 4 A m².

Worked example 7.5: A material has χ = 499. Find μᵣ and B inside it when H = 1000 A/m.

Solution: μᵣ = 1 + χ = 500. B = μ₀μᵣH = 4π × 10⁻⁷ × 500 × 1000 ≈ 0.628 T.

Worked example 7.6: The hysteresis loop of a transformer core encloses 250 J/m³. The core volume is 1000 cm³ and the supply is 50 Hz. Find the power lost as heat.

Solution: Energy per cycle = 250 × 10⁻³ = 0.25 J. Power = 0.25 × 50 = 12.5 W.

Worked example 7.7 (NEET-hard): A paramagnetic sample shows magnetisation 8 A/m at 4 K in a field of 0.6 T. Find its magnetisation at 16 K in a field of 0.2 T, assuming Curie's law holds.

Solution: M is proportional to B₀/T. M₂ = 8 × (0.2/0.6) × (4/16) = 8 × (1/3) × (1/4) ≈ 0.67 A/m.

Quick revision

  • B = μ₀(H + M); M = χH; μᵣ = 1 + χ; B = μ₀μᵣH.

  • H and M both have unit A/m; χ and μᵣ have no unit.

  • Dia: χ small negative, repelled, no permanent moments, temperature independent.

  • Para: χ small positive, weakly attracted, χ proportional to 1/T (Curie law).

  • Ferro: χ very large, domains; paramagnetic above Curie temperature.

  • Superconductor: χ = −1, perfect diamagnet.

  • Hysteresis loop area = energy loss per unit volume per cycle. Soft iron for cores; steel for permanent magnets.

NEET traps

  • Saying a ferromagnet becomes diamagnetic above T_c. It becomes paramagnetic.

  • Using Celsius in Curie's law. T must be in kelvin.

  • Thinking only some materials are diamagnetic. All materials have it; it is masked in others.

  • Choosing soft iron for a permanent magnet because of high retentivity. Its coercivity is too low.

  • Mixing up retentivity (B left at H = 0) and coercivity (reverse H needed to make B = 0).

  • Writing μᵣ = χ. The correct relation is μᵣ = 1 + χ.

Practice MCQs: Chapter 7

Level 1: Concept check

1. The susceptibility of a diamagnetic substance is (a) large and positive (b) small and positive (c) small and negative (d) exactly zero

2. Which of these is ferromagnetic at room temperature? (a) Nickel (b) Copper (c) Aluminium (d) Bismuth

3. Which of these is paramagnetic? (a) Bismuth (b) Aluminium (c) Water (d) Iron

4. According to Curie's law, the susceptibility of a paramagnetic substance is (a) proportional to T (b) independent of T (c) proportional to T² (d) proportional to 1/T

5. Above its Curie temperature, a ferromagnetic substance becomes (a) diamagnetic (b) paramagnetic (c) a superconductor (d) more strongly ferromagnetic

6. Relative permeability and susceptibility are related by (a) μᵣ = 1 + χ (b) μᵣ = χ (c) μᵣ = 1 − χ (d) μᵣ = 1/χ

7. A material for permanent magnets should have (a) low retentivity and low coercivity (b) high retentivity and low coercivity (c) high retentivity and high coercivity (d) low retentivity and high coercivity

8. A superconductor below its critical temperature has susceptibility (a) +1 (b) zero (c) very large (d) −1

9. A diamagnetic substance placed in a non-uniform magnetic field moves (a) from the stronger to the weaker region (b) from the weaker to the stronger region (c) not at all (d) along the field lines toward the north pole

10. The area enclosed by a B–H hysteresis loop gives (a) the retentivity (b) the energy lost per unit volume per cycle (c) the coercivity (d) the permeability

Level 2: NEET standard

11. A solenoid with 1000 turns per metre carries 2 A; its core has μᵣ = 400. The field inside is about (a) 0.5 T (b) 2.0 T (c) 1.0 T (d) 0.1 T

12. The magnetisation of the core in Q11 is about (a) 7.98 × 10⁵ A/m (b) 2.0 × 10³ A/m (c) 8.0 × 10² A/m (d) 1.6 × 10⁶ A/m

13. A paramagnetic salt has χ = 1.2 × 10⁻⁵ at 300 K. At 150 K its χ is (a) 0.6 × 10⁻⁵ (b) 1.2 × 10⁻⁵ (c) 4.8 × 10⁻⁵ (d) 2.4 × 10⁻⁵

14. A paramagnetic sample has magnetisation 8 A/m at 4 K in 0.6 T. At 16 K in 0.2 T, its magnetisation is about (a) 2.67 A/m (b) 0.67 A/m (c) 6 A/m (d) 1.33 A/m

15. Soft iron is preferred for transformer cores because it has (a) high coercivity and wide hysteresis loop (b) low permeability (c) high permeability and a thin hysteresis loop (d) a negative susceptibility

16. Which of these has relative permeability slightly less than 1? (a) Aluminium (b) Bismuth (c) Iron (d) Oxygen

17. A transformer core of volume 1000 cm³ has a hysteresis loop of area 250 J/m³ and runs at 50 Hz. The power lost to hysteresis is (a) 0.25 W (b) 5 W (c) 125 W (d) 12.5 W

18. Liquid oxygen poured between the poles of a strong magnet (a) is held between the poles (b) is pushed away from the poles (c) freezes (d) is not affected

19. Which pair of quantities has the same SI unit? (a) B and H (b) B and M (c) H and M (d) χ and H

20. A diamagnetic liquid fills a U-tube, and one limb is placed between the poles of a strong magnet. The liquid level in that limb (a) rises (b) does not change (c) rises and then falls (d) falls

21. An iron bar of volume 5 cm³ has magnetisation 8 × 10⁵ A/m. Its magnetic moment is (a) 0.4 A m² (b) 4 A m² (c) 40 A m² (d) 1.6 × 10¹¹ A m²

22. The susceptibility of a diamagnetic substance (a) is almost independent of temperature (b) increases as temperature rises (c) varies as 1/T (d) becomes positive above a critical temperature

Level 3: Challenge

23. Thin rods of a diamagnetic, a paramagnetic and a ferromagnetic material hang freely in a uniform horizontal magnetic field. They settle (a) all parallel to the field (b) all perpendicular to the field (c) para and ferro parallel, dia perpendicular to the field (d) dia and para parallel, ferro perpendicular to the field

24. A material has χ = 499. In a magnetic intensity of 1000 A/m, B inside it is about (a) 0.314 T (b) 0.5 T (c) 6.28 T (d) 0.628 T

25. Above its Curie temperature, a material has χ = 2 × 10⁻³ at 100 K above T_c. Following the Curie–Weiss law, at 400 K above T_c its χ is (a) 5 × 10⁻⁴ (b) 1 × 10⁻³ (c) 8 × 10⁻³ (d) 2.5 × 10⁻⁴

26. The core of an electromagnet should have (a) high retentivity and high coercivity (b) high permeability and low coercivity (c) low permeability and high coercivity (d) negative susceptibility

27. In an unmagnetised piece of iron, (a) there are no domains (b) all domains point the same way (c) domains exist but point in random directions (d) atoms have no magnetic moments

28. The magnetisation of a paramagnetic sample reaches saturation when (a) temperature is high and field is weak (b) temperature is high and field is strong (c) temperature is low and field is weak (d) temperature is low and field is strong

29. Assertion (A): Soft iron is used for the cores of electromagnets. Reason (R): Soft iron has a high Curie temperature. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: The susceptibility of a paramagnetic substance rises as its temperature falls. Statement II: Above its Curie temperature, a ferromagnetic substance behaves as a paramagnetic one. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1cInduced moments oppose the field.
2aFe, Co, Ni, Gd are ferromagnetic.
3bAl has permanent atomic moments.
4dχ = Cμ₀/T.
5bDomains break up above T_c.
6aB = μ₀(1 + χ)H.
7cMust keep magnetism and resist demagnetising.
8dPerfect diamagnet, B = 0 inside.
9aRepelled from strong field regions.
10bLoop area = heat per unit volume per cycle.
11c4π × 10⁻⁷ × 400 × 2000 ≈ 1.0 T.
12a(μᵣ − 1)H = 399 × 2000.
13dHalving T doubles χ.
14b8 × (1/3) × (1/4) ≈ 0.67 A/m.
15cStrong response, low loss per cycle.
16bBismuth is diamagnetic.
17d250 × 10⁻³ × 50 = 12.5 W.
18aOxygen is paramagnetic.
19cBoth in A/m.
20dDiamagnetic liquid is pushed out of the strong field.
21bMV = 8 × 10⁵ × 5 × 10⁻⁶.
22aDiamagnetism does not rely on aligning permanent moments.
23cAttracted materials align along B; dia turns across it.
24d4π × 10⁻⁷ × 500 × 1000.
25aχ proportional to 1/(T − T_c): 2 × 10⁻³ × 100/400.
26bStrong when on, easily demagnetised when off.
27cRandom domains cancel overall.
28dThermal disorder small, aligning field large.
29bBoth true; the real reason is high permeability and low coercivity.
30aCurie law; and ferro turns para above T_c.

Chapter 7 revision sheet

One-page summary

  • Magnetisation M = net magnetic moment per unit volume; unit A/m.

  • Magnetic intensity H = nI for a solenoid; unit A/m. B = μ₀(H + M).

  • Susceptibility χ = M/H (no unit); relative permeability μᵣ = 1 + χ; μ = μ₀μᵣ.

  • Diamagnetic: χ small and negative (about −10⁻⁵), weakly repelled, moves from strong to weak field.

  • Diamagnetism comes from induced moments opposing B; atoms have no net permanent moment. It barely depends on temperature.

  • Examples of diamagnets: bismuth, copper, lead, silicon, water, nitrogen gas, sodium chloride.

  • A superconductor below its critical temperature is a perfect diamagnet: χ = −1 (Meissner effect).

  • Paramagnetic: χ small and positive (about 10⁻⁵ to 10⁻³), weakly attracted; atoms have permanent moments.

  • Curie law: M = C B/T, so χ ∝ 1/T for a paramagnet.

  • Examples of paramagnets: aluminium, sodium, calcium, oxygen (liquid O₂ clings to magnet poles), copper chloride.

  • Ferromagnetic: χ very large (10³ and more); domains align; examples iron, cobalt, nickel, gadolinium.

  • Above the Curie temperature a ferromagnet becomes paramagnetic: χ = C/(T − T_c).

  • Hysteresis: retentivity = B left at H = 0; coercivity = reverse H to make B zero; loop area = energy lost per cycle per unit volume.

  • Permanent magnets (steel, alnico): high retentivity and high coercivity. Cores of electromagnets and transformers (soft iron): low coercivity, narrow loop.

Must-remember table

PropertyDiamagneticParamagneticFerromagnetic
χsmall, negativesmall, positivelarge, positive
μᵣslightly less than 1slightly more than 1much more than 1
In a non-uniform fieldmoves to weaker fieldmoves to stronger fieldstrongly pulled to stronger field
Field linesslightly pushed outslightly pulled instrongly pulled in
Temperature effectalmost noneχ ∝ 1/Tparamagnetic above T_c
ExamplesBi, Cu, waterAl, Na, O₂Fe, Co, Ni, Gd

Memory aids

  • "DIA = Dislikes, PARA = Pals, FERRO = Fans": diamagnets are repelled, paramagnets weakly attracted, ferromagnets strongly attracted.

  • "Cold Paramagnets Comply": lower temperature means larger χ (Curie law).

  • "Curie crosses to Para": above the Curie temperature a ferromagnet turns paramagnetic.

  • "Steel Stays, Soft iron Switches": steel keeps its magnetism (permanent magnets); soft iron loses it easily (cores).

  • "Rem-Rest, Co-Cancel": retentivity is what remains at rest (H = 0); coercivity is what cancels B.

Concept connections

  • Hysteresis loss and laminated soft-iron cores matter for transformers in Physics Book 14: Electromagnetic Induction and Alternating Currents.

  • Paramagnetism from unpaired electrons links to Chemistry Book 11: d- and f-Block Elements and Chemistry Book 12: Coordination Compounds.

  • O₂ being paramagnetic is explained by molecular orbital theory in Chemistry Book 3: Chemical Bonding and Molecular Structure.

Practice MCQs: Chapter 7, Level 4 (new NEET pattern)

31. Match each material (at room temperature unless stated) with its magnetic class.

List I:

  • A. Bismuth

  • B. Aluminium

  • C. Nickel

  • D. A superconductor below its critical temperature

List II:

  • (i) paramagnetic

  • (ii) perfect diamagnet, χ = −1

  • (iii) diamagnetic

  • (iv) ferromagnetic

(a) A-i, B-iii, C-iv, D-ii (b) A-iii, B-iv, C-i, D-ii (c) A-iii, B-i, C-ii, D-iv (d) A-iii, B-i, C-iv, D-ii

32. Match each quantity with its relation or unit.

List I:

  • A. Magnetisation M

  • B. Susceptibility χ

  • C. Relative permeability μᵣ

  • D. B inside a material

List II:

  • (i) 1 + χ

  • (ii) μ₀(H + M)

  • (iii) moment per unit volume, A/m

  • (iv) M/H, no unit

(a) A-iii, B-iv, C-i, D-ii (b) A-iv, B-iii, C-i, D-ii (c) A-iii, B-i, C-iv, D-ii (d) A-iii, B-iv, C-ii, D-i

33. Match each class with its typical susceptibility.

List I:

  • A. Diamagnetic

  • B. Paramagnetic

  • C. Ferromagnetic

  • D. Superconductor

List II:

  • (i) about 10³ or more

  • (ii) about −10⁻⁵

  • (iii) exactly −1

  • (iv) about +10⁻⁵ to +10⁻³

(a) A-iv, B-ii, C-i, D-iii (b) A-ii, B-i, C-iv, D-iii (c) A-ii, B-iv, C-i, D-iii (d) A-iii, B-iv, C-i, D-ii

34. Match each hysteresis term with its meaning.

List I:

  • A. Retentivity

  • B. Coercivity

  • C. Area of the B–H loop

  • D. Saturation

List II:

  • (i) reverse H needed to bring B to zero

  • (ii) energy lost per cycle per unit volume

  • (iii) all domains aligned; B barely rises further

  • (iv) B left when H returns to zero

(a) A-i, B-iv, C-ii, D-iii (b) A-iv, B-i, C-ii, D-iii (c) A-iv, B-ii, C-i, D-iii (d) A-iii, B-i, C-ii, D-iv

35. How many of the following statements are correct?

  • A. Diamagnetic susceptibility hardly depends on temperature.

  • B. For a paramagnet, χ ∝ 1/T.

  • C. Above its Curie temperature, a ferromagnet becomes paramagnetic.

  • D. A diamagnetic rod hung in a strong uniform field turns to lie along the field.

  • E. A paramagnetic liquid in a U-tube rises in the limb placed between the magnet poles.

(a) 2 (b) 3 (c) 5 (d) 4

36. Choose the correct set of statements about material for a permanent magnet.

  • A. It should have high retentivity.

  • B. It should have high coercivity.

  • C. Low hysteresis loss is its most important need.

  • D. Steel is a better choice than soft iron.

(a) A and B only (b) A, B and D only (c) B, C and D only (d) A, B, C and D

37. Choose the correct set of statements about material for a transformer core.

  • A. It should have low coercivity.

  • B. It should have a narrow hysteresis loop.

  • C. Soft iron is suitable.

  • D. It should have high coercivity.

(a) A, B and C only (b) A and D only (c) B and D only (d) C and D only

38. How many of the following statements are correct?

  • A. Field lines crowd into a ferromagnetic sample.

  • B. Field lines are slightly pushed out of a diamagnetic sample.

  • C. Every material shows some diamagnetism.

  • D. Ferromagnetism belongs to single isolated atoms, not to domains.

(a) 4 (b) 2 (c) 3 (d) 1

39. For a paramagnetic salt obeying Curie law, the graph of χ against 1/T is (a) a horizontal line (b) a straight line through the origin (c) a parabola (d) a falling straight line with a positive intercept

40. The table gives χ of a paramagnetic salt: 200 K gives 3.0 × 10⁻⁴; 300 K gives 2.0 × 10⁻⁴. At 400 K, χ is (a) 1.0 × 10⁻⁴ (b) 1.33 × 10⁻⁴ (c) 2.5 × 10⁻⁴ (d) 1.5 × 10⁻⁴

41. Two B–H loops are described. Material P has a wide, tall loop (large retentivity and coercivity). Material Q has a tall, very narrow loop (small coercivity). The best use is (a) P for permanent magnets, Q for transformer cores (b) P for transformer cores, Q for permanent magnets (c) both for permanent magnets (d) both for transformer cores

Case for Q42–43: A long solenoid has 1000 turns per metre and carries 2 A. It is filled with an iron core of relative permeability 500 (assume the iron stays below saturation).

42. The field B inside the core is about (a) 2.5 mT (b) 0.63 T (c) 2.51 T (d) 1.26 T

43. The magnetisation M of the core is about (a) 2.0 × 10³ A/m (b) 5.0 × 10⁵ A/m (c) 1.0 × 10⁶ A/m (d) 1.0 × 10³ A/m

44. Above its Curie temperature of 1000 K, a ferromagnetic material has χ = 5 × 10⁻³ at 1100 K. Using χ = C/(T − T_c), its χ at 1200 K is (a) 4.6 × 10⁻³ (b) 2.5 × 10⁻³ (c) 1.25 × 10⁻³ (d) 5.0 × 10⁻³

45. An iron bar of volume 2 × 10⁻⁵ m³ has magnetisation 5 × 10⁵ A/m along its length. It is placed at 30° to a uniform field of 0.2 T. The torque on it is (a) 1.0 N m (b) 2.0 N m (c) 0.5 N m (d) 1.73 N m

Level 4 answer key

QAnsReason
31dBi dia, Al para, Ni ferro, superconductor χ = −1
32aM in A/m; χ = M/H; μᵣ = 1 + χ; B = μ₀(H + M)
33cSmall negative, small positive, large, −1
34bRetentivity remains; coercivity cancels; area = loss; saturation = all aligned
35dOnly D false: a diamagnetic rod sets across the field
36bC false: loss matters for cores, not permanent magnets
37aD false: cores need low coercivity
38cD false: ferromagnetism needs domains of many atoms
39bχ = C′/T is linear in 1/T
40dχT constant = 0.06; 0.06/400 = 1.5 × 10⁻⁴
41aWide loop holds magnetism; narrow loop wastes little energy
42dB = μ₀μᵣnI = 4π × 10⁻⁷ × 500 × 2000 = 1.26 T
43cM = (μᵣ − 1)H = 499 × 2000 ≈ 1.0 × 10⁶ A/m
44bC = 5 × 10⁻³ × 100 = 0.5; 0.5/200
45am = MV = 10 A m²; τ = 10 × 0.2 × 0.5
23 min left
‹
›