Chapter 9 of 9 · 13 min read

Last-Week Revision Kit

Use this kit in the final week: read the glance sheet daily, say the rapid-fire facts aloud, tick the checklist, then sit Mock Test 2 under exam timing.

Book-at-a-glance sheet

Chapter 1: Physical Quantities and Units

ItemKey fact
SI base unitsm, kg, s, A, K, mol, cd
Unit conversionn₁u₁ = n₂u₂; bigger unit, smaller number
Prefixesp 10⁻¹², n 10⁻⁹, μ 10⁻⁶, m 10⁻³, k 10³, M 10⁶, G 10⁹, T 10¹²
Astronomy units1 AU = 1.496 × 10¹¹ m; 1 ly = 9.46 × 10¹⁵ m; 1 pc = 3.08 × 10¹⁶ m
Small units1 fermi = 10⁻¹⁵ m; 1 Å = 10⁻¹⁰ m
Energy units1 eV = 1.6 × 10⁻¹⁹ J; 1 kWh = 3.6 × 10⁶ J; 1 erg = 10⁻⁷ J

Chapter 2: Measuring Instruments and Least Count

ItemKey fact
Vernier LCMSD/n, when n VSD = (n − 1) MSD
Screw gauge LCpitch / circular divisions
ReadingMSR + (coinciding or circular division) × LC
Corrected readingobserved − zero error (with sign)
Positive zero errorvernier zero right of main zero; circular zero below reference line
ParallaxD = b/θ, size d = Dα, angles in radians

Chapter 3: Errors in Measurement

ItemKey fact
Mean absolute erroraverage of magnitudes of (a_mean − aᵢ)
Percentage error(Δa_mean / a_mean) × 100
Sum or differenceabsolute errors add
Product or quotientrelative errors add
Power nrelative error × n
Single readingerror = least count

Chapter 4: Significant Figures

ItemKey fact
Leading zerosnever significant
Trailing zeros after decimal pointsignificant
× and ÷fewest significant figures
+ and −fewest decimal places
Exact 5round to leave an even digit
Order of magnitudea ≤ 3.16 gives b; a > 3.16 gives b + 1

Chapter 5: Dimensions and Dimensional Analysis

ItemKey fact
Energy, work, torque[M L² T⁻²]
Pressure, stress, modulus[M L⁻¹ T⁻²]
h, angular momentum[M L² T⁻¹]
G[M⁻¹ L³ T⁻²]
Time combinations√(l/g), RC, L/R, √(LC)
Homogeneityadded or equated terms share dimensions; trig, log, exp arguments are dimensionless

40 rapid-fire facts

  1. SI has seven base units: metre, kilogram, second, ampere, kelvin, mole and candela.

  2. Since 20 May 2019, every SI base unit is defined by a fixed value of a constant of nature.

  3. The second is fixed by the caesium-133 frequency of 9 192 631 770 Hz.

  4. The metre is fixed by taking the speed of light as exactly 299 792 458 m/s.

  5. The kilogram is fixed by the Planck constant, h = 6.626 070 15 × 10⁻³⁴ J s.

  6. The ampere is fixed by the elementary charge, e = 1.602 176 634 × 10⁻¹⁹ C.

  7. The kelvin is fixed by the Boltzmann constant, k = 1.380 649 × 10⁻²³ J/K.

  8. The mole is fixed by the Avogadro constant, 6.022 140 76 × 10²³ mol⁻¹.

  9. The radian and steradian are dimensionless derived units.

  10. One light year is about 9.46 × 10¹⁵ m.

  11. One astronomical unit is about 1.496 × 10¹¹ m.

  12. One parsec is about 3.08 × 10¹⁶ m, or about 3.26 light years.

  13. One fermi is 10⁻¹⁵ m and one angstrom is 10⁻¹⁰ m.

  14. One electronvolt is 1.6 × 10⁻¹⁹ J; one kilowatt hour is 3.6 × 10⁶ J.

  15. One unified atomic mass unit is 1.66 × 10⁻²⁷ kg.

  16. One standard atmosphere is about 1.013 × 10⁵ Pa.

  17. 1 Pa = 10 dyne/cm² and 1 J = 10⁷ erg.

  18. A bigger unit always gives a smaller numerical value for the same quantity.

  19. Vernier least count is MSD/n when n VSD equal (n − 1) MSD.

  20. Screw gauge least count is pitch divided by the number of circular divisions.

  21. Corrected reading is observed reading minus zero error, with its sign.

  22. A vernier zero to the right of the main-scale zero means a positive zero error.

  23. Backlash error belongs to the screw gauge, not the vernier callipers.

  24. Parallax distance is basis divided by parallax angle in radians.

  25. One arc second is about 4.85 × 10⁻⁶ rad.

  26. Systematic errors are not reduced by repeating a measurement.

  27. Random errors shrink as more readings are averaged.

  28. In sums and differences, absolute errors add.

  29. In products and quotients, relative errors add.

  30. A power multiplies the relative error by that power.

  31. Leading zeros are never significant.

  32. Trailing zeros after a decimal point are always significant.

  33. Multiplication follows the fewest significant figures; addition follows the fewest decimal places.

  34. An exact 5 being dropped leaves the previous digit even.

  35. The order-of-magnitude gate is √10, about 3.16.

  36. Changing units never changes the number of significant figures.

  37. Work, energy and torque all have dimensions [M L² T⁻²].

  38. Planck constant and angular momentum share [M L² T⁻¹].

  39. RC, L/R and √(LC) all have the dimensions of time.

  40. Dimensional analysis cannot find pure-number constants or derive relations with sums, trig or exponential terms.

Common mistakes checklist

  • I convert units with n₁u₁ = n₂u₂ and do not invert the ratio.

  • I don't confuse a light year (distance) with a year (time).

  • I subtract zero error with its sign, so a negative zero error makes the reading bigger.

  • I don't confuse a vernier's positive zero error rule with the screw gauge rule.

  • I convert degrees, minutes and seconds to radians before using D = b/θ.

  • I add absolute errors even when two quantities are subtracted.

  • I multiply relative error by the power and ignore the minus sign of a power in the denominator.

  • I don't confuse significant figures (for × and ÷) with decimal places (for + and −).

  • I can find the order of magnitude by comparing a with 3.16, not with 5.

  • I don't assume a dimensionally correct equation is physically correct.

Mock Test 2: New-pattern paper

30 questions, mixed from all five chapters. Time: 35 minutes. Marking: +4 for a correct answer, −1 for a wrong one, 0 if left blank.

1. Match the prefix in List I with its power of ten in List II.

List I:

  • A. pico

  • B. tera

  • C. milli

  • D. kilo

List II:

  • i. 10³

  • ii. 10⁻¹²

  • iii. 10¹²

  • iv. 10⁻³

(a) A-iii, B-ii, C-iv, D-i (b) A-ii, B-iii, C-iv, D-i (c) A-ii, B-iii, C-i, D-iv (d) A-iv, B-iii, C-ii, D-i

2. Which of these is not an SI base unit? (a) kelvin (b) candela (c) newton (d) mole

3. One light year is about (a) 3.08 × 10¹⁶ m (b) 1.5 × 10¹¹ m (c) 3 × 10⁸ m (d) 9.46 × 10¹⁵ m

4. An auto-rickshaw moves at 54 km/h. Its speed in m/s is (a) 15 (b) 19.4 (c) 1.5 (d) 150

5. Assertion (A): The radian has no dimensions. Reason (R): A plane angle is the ratio of an arc length to a radius. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

6. A vernier has 1 MSD = 1 mm, and 50 vernier divisions coincide with 49 main-scale divisions. Its least count is (a) 0.01 mm (b) 0.05 mm (c) 0.2 mm (d) 0.02 mm

7. A screw gauge has pitch 0.5 mm and 50 circular divisions. With the studs touching, the circular zero is 2 divisions above the reference line. A wire gives MSR = 3.0 mm and CSR = 35. Its corrected diameter is (a) 3.33 mm (b) 3.35 mm (c) 3.37 mm (d) 3.39 mm

8. Choose the correct set of statements.

  • A. Backlash error occurs in vernier callipers.

  • B. The ratchet of a screw gauge stops you from pressing too hard.

  • C. Least count of a screw gauge = pitch × number of circular divisions.

  • D. In the parallax method, D = b/θ.

(a) A and B only (b) B and D only (c) C and D only (d) A, B and D only

9. A tower is viewed from two points 100 m apart, and the parallax angle is 0.5°. The tower is about (a) 11.5 km away (b) 200 m away (c) 5.7 km away (d) 50 m away

10. A graph plots ten repeated readings of a length against trial number, with a dashed line at the true value. Set X lies tightly on the dashed line. Set Y lies tightly in a narrow band well above it. Set Z is widely scattered around it. Set W is widely scattered well above it. Which set shows a systematic error but little random error? (a) X (b) Z (c) W (d) Y

11. Z = A³B²/√C, and the percentage errors in A, B and C are 1%, 2% and 4%. The maximum percentage error in Z is (a) 7% (b) 11% (c) 9% (d) 5%

12. Five readings of a length are 20.4, 20.8, 20.6, 20.2 and 21.0 cm. The percentage error is about (a) 1.2% (b) 2.4% (c) 0.24% (d) 0.6%

13. How many of the following statements are correct?

  • A. Relative error = mean absolute error / mean value.

  • B. Systematic errors can be removed by averaging many readings.

  • C. In Z = A/B, the absolute errors of A and B add to give the absolute error of Z.

  • D. Gross errors come from carelessness or faulty set-ups.

  • E. In g = 4π²L/T², the factor π adds no error.

(a) Two (b) Three (c) Four (d) Five

14. The mass of a cricket ball is measured with 2% error and its speed with 3% error. The maximum percentage error in its kinetic energy is (a) 5% (b) 11% (c) 6% (d) 8%

15. Statement I: Taking more readings reduces random error. Statement II: Taking more readings removes the zero error of an instrument. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

16. The number of significant figures in 0.04050 is (a) 4 (b) 3 (c) 5 (d) 6

17. 6.25 + 1.3 + 0.004, with correct significant figures, is (a) 7.554 (b) 7.55 (c) 8 (d) 7.6

18. 4.8 × 3.15, with correct significant figures, is (a) 15.12 (b) 15 (c) 15.1 (d) 15.120

19. Match each number in List I with its correct scientific notation in List II.

List I:

  • A. 0.000560

  • B. 56 000 (known to two significant figures)

  • C. 5.06

  • D. 560.0

List II:

  • i. 5.600 × 10²

  • ii. 5.60 × 10⁻⁴

  • iii. 5.06 × 10⁰

  • iv. 5.6 × 10⁴

(a) A-iv, B-ii, C-iii, D-i (b) A-ii, B-iv, C-i, D-iii (c) A-ii, B-iii, C-iv, D-i (d) A-ii, B-iv, C-iii, D-i

20. The order of magnitude of 0.00052 is (a) −4 (b) 4 (c) −3 (d) −5

Case for Q21–22: A carpenter in Jaipur measures a tabletop with a steel tape. He records the length as 1.525 m and the breadth as 0.75 m. He needs the area for a glass sheet and the perimeter for edge beading.

21. The area, with correct significant figures, is (a) 1.1 m² (b) 1.14 m² (c) 1.144 m² (d) 1 m²

22. The perimeter, with correct decimal places, is (a) 4.550 m (b) 4.55 m (c) 4.6 m (d) 4.5 m

23. The dimensions of Young's modulus are (a) [M L T⁻²] (b) [M L² T⁻²] (c) [M L⁻² T⁻²] (d) [M L⁻¹ T⁻²]

24. Match the quantity in List I with its dimensions in List II.

List I:

  • A. Power

  • B. Momentum

  • C. Gravitational potential

  • D. Angular velocity

List II:

  • i. [T⁻¹]

  • ii. [L² T⁻²]

  • iii. [M L² T⁻³]

  • iv. [M L T⁻¹]

(a) A-iv, B-iii, C-ii, D-i (b) A-iii, B-ii, C-iv, D-i (c) A-iii, B-iv, C-ii, D-i (d) A-i, B-iv, C-ii, D-iii

25. For many simple pendulums, a graph of log T (y-axis) against log L (x-axis) is a straight line. Dimensional analysis predicts its slope to be (a) 2 (b) 1/2 (c) 1 (d) −1/2

26. The escape speed v from a planet is assumed to depend on G, the planet's mass M and its radius R. Dimensional analysis gives v proportional to (a) √(GM/R) (b) √(GR/M) (c) GM/R (d) √(GMR)

27. Choose the correct set of statements.

  • A. Torque and energy have the same dimensions.

  • B. Stress and pressure have the same dimensions.

  • C. Velocity gradient (dv/dx) has dimensions [T⁻¹].

  • D. Refractive index has dimensions [L T⁻¹].

(a) A and B only (b) B, C and D only (c) A, B and C only (d) A, B, C and D

28. Assertion (A): The equation v = u + at² is wrong. Reason (R): The term at² has the dimensions of length, not velocity. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

29. A pressure of 1.0 × 10⁵ Pa expressed in dyne/cm² is (a) 1.0 × 10⁴ (b) 1.0 × 10⁶ (c) 1.0 × 10⁷ (d) 1.0 × 10³

30. Statement I: A pure number such as 2π can be found by dimensional analysis. Statement II: Dimensional analysis can check whether an equation is dimensionally consistent. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Mock Test 2 answer key

QAnsReason
1bpico 10⁻¹², tera 10¹², milli 10⁻³, kilo 10³
2cNewton is derived: kg m s⁻²
3dDistance light travels in one year
4a54 × (5/18) = 15 m/s
5aArc/radius is length/length, so the angle is dimensionless
6dLC = 1 mm/50 = 0.02 mm
7cLC 0.01 mm; zero error −0.02 mm; 3.35 + 0.02 = 3.37 mm
8bBacklash is a screw error; LC = pitch ÷ divisions
9aθ = 0.5 × π/180 = 8.73 × 10⁻³ rad; D = 100/θ ≈ 11 460 m
10dTight but offset readings mean a systematic shift with little scatter
11c3(1) + 2(2) + ½(4) = 9%
12aMean 20.6 cm; mean absolute error 0.24 cm; 0.24/20.6 ≈ 1.2%
13bA, D, E true; averaging fails for systematic errors; quotients add relative errors
14dK = ½mv²: 2% + 2(3%) = 8%
15cZero error is systematic; it must be corrected, not averaged
16a4, 0, 5 and the trailing 0 count
17dSum 7.554; fewest decimal places is one, so 7.6
18b15.12; 4.8 has two significant figures, so 15
19dKeep the same significant figures in a
20c5.2 × 10⁻⁴ and 5.2 > 3.16, so −4 + 1 = −3
21a1.14375 m²; 0.75 has two significant figures, so 1.1 m²
22b1.525 + 0.75 + 1.525 + 0.75 = 4.550; two decimal places gives 4.55 m
23dStress/strain, and strain is dimensionless
24cPower [M L² T⁻³], momentum [M L T⁻¹], potential [L² T⁻²], ω [T⁻¹]
25bT varies as √(L/g), so log T = ½ log L + constant
26aGᵃMᵇRᶜ: a = ½, b = ½, c = −½
27cRefractive index is a ratio of speeds, so dimensionless
28aat² is [L T⁻²][T²] = [L]; it cannot be added to a velocity
29b1 Pa = 10 dyne/cm²
30dPure numbers have no dimensions, so the method cannot find them
13 min left
‹
›