Chapter 8 of 11 · 26 min read

Chapter 6: Motion in a Vertical Circle

What you will learn

  • Why the speed and string tension change around a vertical circle.

  • How to find tension at the top, bottom and any angle using Newton's law plus energy conservation.

  • The critical speeds √(gr) at the top and √(5gr) at the bottom for a string.

  • What happens when the speed at the bottom is too small: oscillation, or the string going slack.

  • How a rod, a tube or a bead on a wire changes the critical speed, and how humps and dips on roads behave.

6.1 Why a vertical circle is different

Swing a bucket of water in a vertical circle, the way a village boy sometimes shows off at the well. The bucket slows down as it rises and speeds up as it falls. This is non-uniform circular motion.

Gravity is the reason. On the way up, part of mg points backward along the path and slows the bucket. On the way down it speeds the bucket up. The tension is always along the string, towards the centre, so it does no work. Only gravity does work. So mechanical energy is conserved.

Every vertical circle problem uses two tools:

  1. Newton's second law along the radius: net force towards the centre = mv²/r.

  2. Energy conservation: links the speed at one point to the speed at another.

6.2 The general equations

Let a body of mass m move on a string of length r. Let u be its speed at the lowest point. Let θ be the angle the string makes with the downward vertical.

The body has risen by r(1 − cos θ). Energy conservation gives:

v2=u2−2gr (1−cos⁡θ)v^2 = u^2 - 2gr\,(1 - \cos\theta)

Along the string, tension T points to the centre. The radial part of gravity, mg cos θ, points away from the centre. So:

T−mgcos⁡θ=mv2r  ⇒  T=mu2r+mg (3cos⁡θ−2)T - mg\cos\theta = \frac{mv^2}{r} \;\Rightarrow\; T = \frac{mu^2}{r} + mg\,(3\cos\theta - 2)

6.3 Tension at the bottom and at the top

At the bottom (θ = 0): tension acts up, weight acts down.

Tbottom=mg+mu2rT_{\text{bottom}} = mg + \frac{mu^2}{r}

At the top (θ = 180°): both tension and weight act down, towards the centre. The speed there satisfies v_top² = u² − 4gr.

Ttop=mvtop2r−mgT_{\text{top}} = \frac{m v_{\text{top}}^2}{r} - mg

Subtract the two. The difference is always the same, whatever the speed, as long as the string stays tight:

Tbottom−Ttop=6mgT_{\text{bottom}} - T_{\text{top}} = 6mg

The string is most likely to break at the bottom, where tension is largest.

Figure 6.1 · Forces at the top and bottom of a vertical circle, with critical speeds
Figure 6.1 · Forces at the top and bottom of a vertical circle, with critical speeds

At the top, tension and weight both point to the centre; at the bottom, tension must beat the weight, which is why the string is most likely to snap there.

6.4 Critical speeds for a string

A string can pull but cannot push. So T can never be negative. At the top, T ≥ 0 gives:

vtop≥grv_{\text{top}} \ge \sqrt{gr}

At the minimum speed, gravity alone provides the centripetal force at the top, and the string just goes limp for an instant. That is why the water stays in a fast-swung bucket: at the top, gravity is not enough to provide mv²/r, so the bucket's base pushes on the water.

Using energy, the matching minimum speeds elsewhere are:

PositionMinimum speed (string)Tension at that speed
Top√(gr)0
Horizontal (side)√(3gr)3mg
Bottom√(5gr)6mg

At the minimum speed, the kinetic energy at the bottom is five times that at the top.

6.5 What if the speed at the bottom is less than √(5gr)?

Speed u at the bottomWhat happens
u ≥ √(5gr)Completes the circle; string tight all the way round
√(2gr) < u < √(5gr)Rises above the horizontal, string goes slack before the top, body falls inward as a projectile
0 < u ≤ √(2gr)Never rises above the horizontal level of the centre; swings back and forth like a pendulum

Why √(2gr)? With u = √(2gr), the body just reaches the horizontal position (height r) with zero speed. Below the horizontal, the radial part of gravity points outward, so a tight string never goes slack there.

In the middle case, the string goes slack where T = 0. Put T = 0 in the general equation:

cos⁡θ=2gr−u23gr,hslack=r(1−cos⁡θ)=u2+gr3g\cos\theta = \frac{2gr - u^2}{3gr}, \qquad h_{\text{slack}} = r(1 - \cos\theta) = \frac{u^2 + gr}{3g}

Here h is the height above the lowest point.

6.6 String versus rod

A light rod, a ball rolling inside a smooth tube, or a bead threaded on a circular wire can be pushed as well as pulled. So these can pass the top with any speed above zero.

FeatureString (or inside of a loop track)Rod, tube or bead on wire
Can the support push?NoYes
Minimum speed at top√(gr)Just above 0
Minimum speed at bottom√(5gr)2√(gr) = √(4gr)
Force at top at minimum speedTension = 0Rod pushes up with mg

A block sliding on the inside of a smooth loop-the-loop track behaves like the string case. The track can push inward only, never pull.

Loop-the-loop from a height. A block released from rest at height h on a smooth track enters a vertical loop of radius R. It needs √(5gR) at the bottom. So mgh ≥ ½m(5gR), giving h ≥ 5R/2.

6.7 Humps and dips on roads

A car on a road shaped like part of a vertical circle follows the same rules.

Over a hump (convex bridge) of radius r: mg − N = mv²/r. So N = mg − mv²/r, less than the weight. You feel lighter. If v reaches √(gr), N becomes zero and the car loses contact.

Through a dip (concave road) of radius r: N − mg = mv²/r. So N = mg + mv²/r, more than the weight. You feel pressed into the seat, and tyres and springs are under extra load.

Worked example 6.1: A 0.5 kg stone tied to a 1 m string moves in a vertical circle. Its speed at the lowest point is 8 m/s. Find the tension at the bottom and at the top.

Solution: T_bottom = mg + mu²/r = 5 + 0.5 × 64 / 1 = 37 N. v_top² = 64 − 4 × 10 × 1 = 24. T_top = 0.5 × 24 / 1 − 5 = 7 N. Check: 37 − 7 = 30 N = 6mg.

Worked example 6.2: A ball on a 2.5 m string is to complete a vertical circle. Find the minimum speeds at the bottom and at the top.

Solution: Bottom: √(5gr) = √125 = 5√5 ≈ 11.2 m/s. Top: √(gr) = √25 = 5 m/s.

Worked example 6.3: A boy swings a bucket of water in a vertical circle of radius 0.9 m. What is the least speed at the top for the water not to fall out? How many revolutions per second is that?

Solution: v = √(gr) = √9 = 3 m/s. Revolutions per second = v / (2πr) = 3 / (2π × 0.9) ≈ 0.53. (The speed is higher at the bottom, so this is a lower limit on the average rate.)

Worked example 6.4: A body on a string moves round a vertical circle with just the minimum speed needed. Find the tension when the string is horizontal.

Solution: At the side, v² = 5gr − 2gr = 3gr. Gravity is now tangential and adds nothing along the string. So T = mv²/r = 3mg.

Worked example 6.5: A 0.2 kg stone is tied to a 0.5 m string that breaks at 20 N. What is the greatest speed it can have at the lowest point? Can it complete the circle at that speed?

Solution: T_bottom = mg + mu²/r: 20 = 2 + 0.2u² / 0.5, so 0.4u² = 18, u² = 45 and u ≈ 6.7 m/s. The minimum needed is √(5gr) = √25 = 5 m/s. Since 6.7 > 5, yes, it completes the circle.

Worked example 6.6: A bob on a 0.9 m string is given a speed of √(3gr) at the lowest point. At what height above the lowest point does the string go slack?

Solution: h = (u² + gr) / (3g) = (3gr + gr) / (3g) = 4r/3 = 1.2 m. The angle from the downward vertical satisfies cos θ = (2gr − 3gr)/(3gr) = −1/3, so θ ≈ 109.5°.

Worked example 6.7: A small ball is fixed to one end of a light rod of length 0.5 m. The other end is pivoted. Find the least speed at the bottom for the ball to go right round.

Solution: For a rod, the ball may reach the top with almost zero speed. So ½mu² = mg(2r), u = √(4gr) = √20 = 2√5 ≈ 4.5 m/s.

Worked example 6.8: A 1000 kg car crosses a hump-backed bridge of radius 40 m. (a) Find its greatest speed at the top without losing contact. (b) Find the normal force at the top when its speed is 10 m/s.

Solution: (a) v = √(gr) = √400 = 20 m/s = 72 km/h. (b) N = mg − mv²/r = 10000 − 1000 × 100 / 40 = 10000 − 2500 = 7500 N.

Worked example 6.9 (NEET-hard): A small block slides without friction down a track and into a vertical loop of radius 0.8 m. (a) Find the least release height. (b) For that height, find the normal force at the bottom of the loop in terms of mg.

Solution: (a) h = 5R/2 = 2 m. (b) At the bottom, v² = 2gh = 40 = 5gR. N − mg = mv²/R = 5mg, so N = 6mg.

Quick revision

  • v² = u² − 2gr(1 − cos θ); T = mu²/r + mg(3cos θ − 2).

  • T_bottom = mg + mu²/r; T_top = mv_top²/r − mg; difference 6mg.

  • String: v_top ≥ √(gr); u_bottom ≥ √(5gr); side speed √(3gr), tension 3mg there.

  • √(2gr) < u < √(5gr): string slack at height (u² + gr)/(3g).

  • u ≤ √(2gr): oscillates below the horizontal.

  • Rod, tube or bead: u_bottom ≥ 2√(gr), top speed can be nearly zero.

  • Smooth loop from rest: release height ≥ 5R/2.

  • Hump: N = mg − mv²/r, contact lost at √(gr). Dip: N = mg + mv²/r.

NEET traps

  • Writing T_top = mv²/r + mg. At the top both forces point to the centre, so T = mv²/r − mg.

  • Using √(5gr) for a rod. A rod needs only 2√(gr) at the bottom.

  • Thinking the string can go slack below the horizontal. It cannot.

  • Treating vertical circular motion as uniform. Speed varies; only energy is conserved.

  • Using h = 2R for the loop-the-loop release height. The block needs speed at the top, so h = 2.5R.

  • Mixing up hump and dip: on a hump you feel lighter, in a dip heavier.

Practice MCQs: Chapter 6

Level 1: Concept check

1. For a stone on a string moving in a vertical circle of radius r, the minimum speed at the top is (a) √(gr) (b) √(2gr) (c) √(5gr) (d) zero

2. For the stone in Q1, the minimum speed at the bottom to complete the circle is (a) √(3gr) (b) √(gr) (c) √(5gr) (d) √(2gr)

3. In a vertical circle on a string, the tension is greatest at the (a) top (b) bottom (c) horizontal position (d) same value everywhere

4. The difference between the tensions at the bottom and the top of a vertical circle (string taut throughout) is (a) 2mg (b) 4mg (c) 5mg (d) 6mg

5. If the string is replaced by a light rigid rod, the minimum speed at the top is just above (a) zero (b) √(gr) (c) √(2gr) (d) √(5gr)

6. Motion of a stone on a string in a vertical circle is (a) uniform circular motion (b) non-uniform circular motion (c) straight-line motion (d) projectile motion throughout

7. At the top of the circle, at the minimum speed, the string tension is (a) mg (b) 6mg (c) zero (d) 2mg

8. For a ball on a light rod, the minimum speed at the bottom to complete the vertical circle is (a) √(5gr) (b) √(3gr) (c) √(gr) (d) 2√(gr)

9. A car crosses the top of a convex (hump-shaped) bridge. The normal force on it is (a) more than mg (b) less than mg (c) equal to mg (d) always zero

10. For a stone on a string in a vertical circle with no air drag, the mechanical energy (a) stays constant (b) increases (c) decreases (d) is zero

Level 2: NEET standard

11. A 0.2 kg stone on a 0.5 m string has a speed of 6 m/s at the lowest point of a vertical circle. The tension at the top is (a) 6.4 N (b) 4.4 N (c) 16.4 N (d) 2 N

12. For the stone in Q11, the tension at the bottom is (a) 14.4 N (b) 12.4 N (c) 16.4 N (d) 18.4 N

13. The minimum speed at the bottom for a stone on a 1.6 m string to complete a vertical circle is (a) 4 m/s (b) 4√5 m/s (c) 8 m/s (d) 2√5 m/s

14. A bucket of water is swung in a vertical circle of radius 1.6 m. The least speed at the top for the water to stay in is (a) 2 m/s (b) 8 m/s (c) 16 m/s (d) 4 m/s

15. A ball on a string goes round a vertical circle with the minimum speed needed. The tension when the string is horizontal is (a) mg (b) 2mg (c) 3mg (d) 6mg

16. A road bridge is shaped like an arc of radius 90 m. The greatest speed at which a car can cross the top without losing contact is (a) 30 m/s (b) 9 m/s (c) 90 m/s (d) 45 m/s

17. A 1200 kg car passes through a dip of radius 50 m at 10 m/s. The normal force on it at the lowest point is (a) 9600 N (b) 14400 N (c) 12000 N (d) 2400 N

18. A small block slides without friction down a track into a vertical loop of radius 1.2 m. The least release height (above the bottom of the loop) to go round the loop is (a) 2.4 m (b) 3.6 m (c) 3 m (d) 6 m

19. A 0.5 kg stone is whirled in a vertical circle on a 1 m string that breaks at 40 N. The greatest speed it can have at the lowest point is (a) √70 m/s (b) √80 m/s (c) √50 m/s (d) √90 m/s

20. A stone on a string completes a vertical circle with the minimum speed. The ratio of its kinetic energy at the bottom to that at the top is (a) 3 : 1 (b) 2 : 1 (c) 4 : 1 (d) 5 : 1

21. A bob on a string of length r is given a speed of √(2gr) at the lowest point. It will (a) rise to the level of the centre and swing back (b) complete the circle (c) leave the circle above the horizontal (d) rise to a height 2r

22. A stone on a string has speed √(6gr) at the lowest point of a vertical circle. The ratio of tension at the bottom to tension at the top is (a) 6 : 1 (b) 7 : 1 (c) 5 : 1 (d) 3 : 1

Level 3: Challenge

23. A bob on a string of length r is given a speed √(4gr) at the lowest point. The string goes slack at a height above the lowest point of (a) 4r/3 (b) 5r/3 (c) 2r (d) 3r/2

24. A stone on a string goes round a vertical circle with the minimum speed needed. The tension when the string makes 60° with the downward vertical is (a) 4mg (b) 3mg (c) 4.5mg (d) 5.5mg

25. A small block starts from rest at the top of a fixed smooth sphere of radius R and slides down. It leaves the surface at a height above the centre of the sphere equal to (a) R/2 (b) R/3 (c) 3R/4 (d) 2R/3

26. A ball on a light rod of length 0.4 m is given the least speed at the bottom needed to go right round. Its speed when the rod is horizontal is (a) 2 m/s (b) 2√2 m/s (c) 4 m/s (d) zero

27. A pendulum bob is pulled until the string is horizontal and then released. The tension at the lowest point is (a) 3mg (b) mg (c) 2mg (d) 5mg

28. A bob on a string is given a speed of √(3gr) at the lowest point. The string goes slack when it makes an angle θ with the downward vertical, where θ is (a) cos⁻¹(1/3) (b) cos⁻¹(−2/3) (c) 120° (d) cos⁻¹(−1/3)

29. Assertion (A): A bead threaded on a smooth vertical circular wire can go right round if its speed at the lowest point is just above 2√(gr). Reason (R): The wire can push the bead either inward or outward, so the bead may pass the top with almost zero speed. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: For a stone on a taut string in a vertical circle, the tension at the lowest point exceeds that at the top by 6mg, whatever the speed. Statement II: The minimum speed at the lowest point for a stone on a string to complete a vertical circle is √(3gr). (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1aT = 0 at top: mg = mv²/r
2cu² = gr + 4gr
3bSpeed is greatest and mg opposes T there
4dDerived: T_bottom − T_top = 6mg
5aA rod can push, so v_top can be nearly zero
6bSpeed changes with height
7cGravity alone gives the centripetal force
8d½mu² = mg × 2r
9bN = mg − mv²/r
10aTension does no work; gravity is conservative
11bv_top² = 16; 0.2 × 16/0.5 − 2 = 4.4 N
12c2 + 0.2 × 36/0.5 = 16.4 N
13b√(5 × 10 × 1.6) = √80
14d√(10 × 1.6) = 4 m/s
15cv² = 3gr at the side; T = mv²/r
16a√(10 × 90) = 30 m/s
17b12000 + 1200 × 100/50 = 14400 N
18ch = 2.5R = 3 m
19a40 = 5 + 0.5u²/1, so u² = 70
20dv² ratio 5gr : gr
21a½mu² = mgr: just reaches height r
22bT_bottom = 7mg; v_top² = 2gr gives T_top = mg
23bh = (4gr + gr)/(3g)
24c5mg + mg(3 × 0.5 − 2) = 4.5mg
25dN = 0 when cos θ = 2/3
26bv² = 4gr − 2gr = 2gr = 8
27av² = 2gr; T = mg + 2mg
28dcos θ = (2gr − 3gr)/(3gr) = −1/3
29aSame as the rod case; R gives the reason
30cI is true; the minimum is √(5gr), not √(3gr)

Chapter 6 revision sheet

One-page summary

  • Motion in a vertical circle is non-uniform: gravity changes the speed as the body rises and falls.

  • Two tools: energy conservation for speed, Newton's second law along the radius for tension.

  • Speed at angle θ from the bottom: v² = u² − 2gR(1 − cos θ), where u is the speed at the bottom.

  • Radial equation: T − mg cos θ = mv²/R (θ from the bottom). Tension is greatest at the bottom and least at the top.

  • String, to just complete the circle: v(top) = √(gR), v(bottom) = √(5gR), v(horizontal) = √(3gR).

  • In that minimum case: T(top) = 0, T(horizontal) = 3mg, T(bottom) = 6mg.

  • For any speed that completes the circle: T(bottom) − T(top) = 6mg.

  • Tension at angle θ (minimum case): T = 3mg(1 + cos θ).

  • u ≤ √(2gR): the bob oscillates and never goes above the horizontal diameter; tension never becomes zero below it.

  • √(2gR) < u < √(5gR): the string slackens somewhere in the upper half, and the bob follows a parabola.

  • Rigid rod or bead on a ring: the top speed can be zero, so u(min) = √(4gR) = 2√(gR).

  • Car over a hump of radius R: N = mg − mv²/R; it leaves the road if v > √(gR).

  • Car in a dip: N = mg + mv²/R, so riders feel heavier.

  • Block on a smooth track into a loop of radius R: it must start from at least 2.5R above the bottom.

Must-remember table

QuantityString / trackRod / bead
Minimum speed at top√(gR)0
Minimum speed at bottom√(5gR)√(4gR)
Speed at horizontal (minimum case)√(3gR)√(2gR)
Tension at bottom (minimum case)6mg5mg
T(bottom) − T(top)6mg6mg
Release height for a loop2.5R2R
Oscillation only ifu ≤ √(2gR)u less than √(4gR)

Memory aids

  • "1-3-5 for speed squared": v²/gR is 1 at the top, 3 at the side, 5 at the bottom in the minimum case.

  • "0-3-6 for tension": T/mg is 0 at the top, 3 at the side, 6 at the bottom in the same case.

  • "Six is the gap": T(bottom) − T(top) = 6mg whatever the speed, as long as the circle is completed.

  • "Rod removes the 1": a rod can push, so it needs no √(gR) at the top; the bottom speed drops from √5 to √4.

Concept connections

  • Uniform circular motion, centripetal acceleration v²/R and angular speed come from Physics Book 2: Kinematics.

  • Centripetal force, banking of roads and the car-on-a-hump problem rely on Physics Book 3: Laws of Motion.

  • The same "gravity supplies the centripetal force" idea gives orbital speed in Physics Book 6: Gravitation.

Practice MCQs: Chapter 6, Level 4 (new NEET pattern)

31. A bob of mass m on a light string of length R just completes a vertical circle. Match List I with List II.

  • A. Speed at the top

  • B. Speed at the bottom

  • C. Speed when the string is horizontal

  • D. Tension at the bottom

List II: (i) √(3gR) (ii) 6mg (iii) √(gR) (iv) √(5gR)

(a) A-iii, B-iv, C-i, D-ii (b) A-iv, B-iii, C-i, D-ii (c) A-iii, B-i, C-iv, D-ii (d) A-iii, B-iv, C-ii, D-i

32. Match List I with List II for motion in a vertical circle of radius R.

  • A. T(bottom) − T(top) for a string, circle completed

  • B. T(horizontal) − T(top) for a string, circle completed

  • C. Minimum speed at the top for a bob on a light rigid rod

  • D. Minimum speed at the bottom for a bob on a light rigid rod

List II: (i) 0 (ii) 3mg (iii) 6mg (iv) 2√(gR)

(a) A-ii, B-iii, C-i, D-iv (b) A-iii, B-ii, C-iv, D-i (c) A-iii, B-ii, C-i, D-iv (d) A-i, B-ii, C-iii, D-iv

33. Match List I with List II (mass m, speed v, radius R).

  • A. Highest speed at which a car stays on the top of a hump

  • B. Normal force on a car at the bottom of a dip

  • C. Force by the seat on an upside-down pilot at the top of a loop

  • D. Normal force on a car at the top of a hump

List II: (i) mg + mv²/R (ii) mv²/R − mg (iii) mg − mv²/R (iv) √(gR)

(a) A-iv, B-ii, C-i, D-iii (b) A-iv, B-i, C-ii, D-iii (c) A-i, B-iv, C-ii, D-iii (d) A-iv, B-i, C-iii, D-ii

34. A stone tied to a 2.5 m string is whirled in a vertical circle. Match List I with List II.

  • A. Minimum speed at the top to complete the circle

  • B. Minimum speed at the bottom to complete the circle

  • C. Speed at the horizontal position in that minimum case

  • D. Speed at the bottom needed just to reach the horizontal position

List II: (i) 5 m/s (ii) 7.1 m/s (iii) 8.7 m/s (iv) 11.2 m/s

(a) A-i, B-iii, C-iv, D-ii (b) A-ii, B-iv, C-iii, D-i (c) A-i, B-iv, C-ii, D-iii (d) A-i, B-iv, C-iii, D-ii

35. How many of the following statements are correct?

  • A. Motion of a bob in a vertical circle is non-uniform circular motion.

  • B. The string tension is greatest at the lowest point.

  • C. When the bob just completes the circle, the tension at the top is zero.

  • D. For a bob on a rigid rod, the minimum speed at the top is √(gR).

  • E. A string-held bob needs a speed of at least √(5gR) at the bottom to complete the circle.

(a) 4 (b) 3 (c) 5 (d) 2

36. A bob on a string of length R is given a speed u at the bottom, with √(2gR) < u < √(5gR). Choose the correct set of statements.

  • A. The string slackens somewhere in the upper half of the circle.

  • B. The bob swings to and fro about the bottom with the string always taut.

  • C. The bob leaves the circle at a point above the horizontal diameter.

  • D. After the string slackens, the bob moves along a parabola.

(a) A and B only (b) B and D only (c) A, C and D only (d) All of A, B, C and D

37. A bob on a string of length R is given a speed u at the bottom, with u < √(2gR). Choose the correct set of statements.

  • A. The bob oscillates about the lowest point.

  • B. The string never becomes slack.

  • C. The bob rises above the horizontal diameter.

  • D. The bob's speed is zero at each extreme position.

(a) A and C only (b) B and C only (c) C and D only (d) A, B and D only

38. A roller-coaster car runs through a vertical loop. How many of the following statements are correct?

  • A. Riders feel heaviest at the bottom of the loop.

  • B. If the speed at the top is exactly √(gR), riders feel weightless there.

  • C. The loop is designed so that the speed at the top is less than √(gR).

  • D. The car's kinetic energy is larger at the bottom than at the top.

(a) 2 (b) 3 (c) 4 (d) 1

39. A 0.2 kg bob just completes a vertical circle on a string. A graph of tension T against the angle θ from the lowest point follows T = 3mg(1 + cos θ), from 6mg at θ = 0 to 0 at θ = 180°. The tension at θ = 60° is

(a) 6 N (b) 12 N (c) 9 N (d) 3 N

40. A bob on a 1 m string is given different speeds at the lowest point.

TrialSpeed at bottom (m/s)
P3
Q5
R7
S8

In how many trials does the bob complete the circle with the string taut throughout?

(a) 1 (b) 2 (c) 3 (d) 0

41. For a 0.5 kg bob on a 1 m string, a graph of v² against height h above the lowest point is a straight line. It meets the v²-axis at 60 m²/s² and has slope −20 m/s². The tension at the top of the circle is

(a) 10 N (b) 5 N (c) zero, the string is just slack (d) 15 N

Passage for Q42–43: In a circus, a cyclist rides a loop-the-loop track of radius 4 m. The cyclist and cycle together have a mass of 80 kg. Treat them as a point mass and ignore friction.

42. The minimum speed at the top of the loop for the cyclist to stay on the track is about

(a) 4 m/s (b) 8.9 m/s (c) 2 m/s (d) 6.3 m/s

43. If the speed at the top is 8 m/s, the normal force from the track at the top is

(a) 480 N (b) 1280 N (c) 800 N (d) 2080 N

44. A bob on a 1 m string is given a speed of 6 m/s at the lowest point. The height above the lowest point at which the string becomes slack is about

(a) 1.0 m (b) 1.53 m (c) 2.0 m (d) 1.8 m

45. A 0.5 kg block slides from rest down a smooth track that ends in a vertical loop of radius 0.8 m. The minimum release height (above the loop's bottom) to go round the loop, and the normal force at the loop's bottom for that release, are

(a) 1.6 m, 30 N (b) 2 m, 25 N (c) 2 m, 30 N (d) 2.5 m, 30 N

Level 4 answer key

QAnsReason
31aMinimum case: √(gR), √(5gR), √(3gR) and T(bottom) = mg + 5mg = 6mg
32c6mg and 3mg from energy plus radial equation; a rod can push, so top speed 0 and bottom speed √(4gR)
33bHump: N = 0 at √(gR); dip adds mv²/R; upside-down pilot: N + mg = mv²/R
34d√25 = 5; √125 ≈ 11.2; √75 ≈ 8.7; √(2gR) = √50 ≈ 7.1 m/s
35aOnly D is false; a rod needs zero speed at the top
36cBetween √(2gR) and √(5gR) the bob rises above the horizontal, the string goes slack, and it flies off in a parabola
37dIt cannot rise above the horizontal; tension stays positive below it
38bA, B, D true; below √(gR) at the top the car would fall off the track
39cT = 3 × 0.2 × 10 × (1 + 0.5) = 9 N
40a√(5gR) = √50 ≈ 7.07 m/s; only 8 m/s exceeds it
41bv²(top) = 60 − 20 × 2 = 20; T = 0.5 × 20/1 − 5 = 5 N
42d√(gR) = √40 ≈ 6.3 m/s
43aN = mv²/R − mg = 80 × 64/4 − 800 = 480 N
44bv² = 16 + 20 cos θ; T = 0 gives 16 + 30 cos θ = 0, cos θ = −8/15; h = R(1 − cos θ) ≈ 1.53 m
45cH(min) = 2.5R = 2 m; v² = 5gR at bottom, N = mg + 5mg = 6 × 5 = 30 N
26 min left
‹
›