Chapter 10 of 10 · 15 min read

Last-Week Revision Kit

This kit is for the final week: one glance sheet, 40 facts to know cold, a self-check list and a full new-pattern mock paper.

Book-at-a-glance sheet

Chapter 1: Measuring Instruments

ItemFormula or fact
Vernier LC1 MSD − 1 VSD = 1 MSD/n
Screw gauge LCpitch/number of circular divisions
Corrected readingobserved − zero error (with sign)
Positive zero errorvernier zero right of main zero; circular zero below reference line
Momentsm d₁ = M d₂ about the knife-edge at G

Chapter 2: Mechanics and Properties of Matter

ItemFormula or fact
Pendulum energyE ∝ A²; ln A² vs t is a straight line
Young's modulusY = MgL/(πr²ℓ) = gL/(πr² × slope of ℓ vs M)
Capillary riseh = 2T cos θ/(rρg); h r = constant
Terminal velocityv = 2r²(ρ − σ)g/(9η)

Chapter 3: Heat and Sound

ItemFormula or fact
Speed of soundv = 2f(l₂ − l₁) = 4f(l₁ + e)
End correctione = (l₂ − 3l₁)/2 ≈ 0.3 × diameter
Method of mixturesmₛcₛ(Tₛ − T) = (m_w c_w + m_c c_c)(T − T_w)
Water equivalentm_c c_c/c_w (in kg)

Chapter 4: Electricity

ItemFormula or fact
Metre bridgeX = R l/(100 − l)
Resistivityρ = πr²X/L
Ohm's lawslope of V–I = R; slope of I–V = 1/R
Half deflectionG = RS/(R − S) ≈ S when R is much larger than S
Figure of meritk = E/((R + G)θ), in A/division

Chapter 5: Optics

ItemFormula or fact
Mirror1/f = 1/v + 1/u
Lens1/f = 1/v − 1/u
Convex mirrorf = R/2, R from the lens-image point
Prismn = sin((A + δm)/2)/sin(A/2); i = e at δm
Glass slabn = (R₃ − R₁)/(R₃ − R₂)

Chapter 6: Electronics

ItemFormula or fact
Knee voltageSi ≈ 0.7 V, Ge ≈ 0.3 V
Dynamic resistancer_d = ΔV/ΔI
Zener currentI_Z = (V_in − V_Z)/R_s − V_Z/R_L
Identificationresistor both ways; diode one way; LED one way + glow; capacitor brief kick

40 rapid-fire facts

  1. Least count is the smallest reading an instrument can give directly.

  2. A vernier with 10 VSD = 9 MSD (1 mm) has LC 0.1 mm.

  3. A vernier with 50 VSD = 49 MSD (1 mm) has LC 0.02 mm.

  4. A screw gauge with pitch 0.5 mm and 50 divisions has LC 0.01 mm.

  5. Zero error is subtracted with its sign; a negative error is effectively added.

  6. The ratchet of a screw gauge gives a uniform, gentle pressure.

  7. Backlash error is avoided by turning the screw in one direction only.

  8. Wire diameter is measured at several places in two perpendicular directions.

  9. In the metre-scale experiment, the scale is balanced alone first to find G.

  10. A pendulum's energy is proportional to the square of its amplitude.

  11. If the amplitude halves, energy falls to one quarter.

  12. In Searle's method, the reference wire cancels temperature and support effects.

  13. Young's modulus is a property of the material, not of the wire's size.

  14. In Y = MgL/(πr²ℓ), the radius error counts twice.

  15. Capillary rise is inversely proportional to tube radius.

  16. Detergent lowers surface tension and reduces capillary rise.

  17. Mercury is depressed in a glass capillary.

  18. Terminal velocity is proportional to the square of the ball's radius.

  19. Viscosity of a liquid falls as temperature rises.

  20. At terminal velocity, weight = upthrust + viscous force.

  21. The resonance tube acts as a pipe closed at the water surface.

  22. Resonance lengths in a closed tube are λ/4 − e, 3λ/4 − e, 5λ/4 − e.

  23. v = 2f(l₂ − l₁) is free of end correction.

  24. End correction depends on the tube's radius, about 0.3 times its diameter.

  25. Speed of sound in air rises about 0.6 m/s per °C.

  26. Specific heat of water is taken as 4200 J kg⁻¹ K⁻¹.

  27. Heat loss to the room makes the measured specific heat of a solid too low.

  28. The metre bridge is a Wheatstone bridge using a 100 cm wire.

  29. At balance, the galvanometer carries no current.

  30. The balance point should be near the middle of the wire for best accuracy.

  31. Interchanging X and R moves the balance length from l to 100 − l.

  32. A smaller figure of merit means a more sensitive galvanometer.

  33. In parallax, the farther object moves with the eye.

  34. For a concave mirror, the pin coincides with its own image at the centre of curvature.

  35. A convex mirror's focal length needs a convex lens to supply a real image.

  36. The i–δ curve of a prism has one minimum, δm.

  37. For a slab in air, apparent thickness is real thickness divided by n.

  38. A Si diode starts conducting appreciably near 0.7 V.

  39. A Zener diode keeps a nearly constant voltage in reverse breakdown.

  40. A capacitor gives a brief deflection that dies away in a DC test.

Common mistakes checklist

  • I can find the sign of zero error for both vernier callipers and screw gauge without guessing.

  • I subtract the zero error with its sign, every time.

  • I don't confuse pitch with least count.

  • I don't confuse "amplitude halves" with "energy halves".

  • I use radius, not diameter, in Y = MgL/(πr²ℓ) and ρ = πr²X/L.

  • I can find end correction from two resonance lengths.

  • I include the calorimeter's heat capacity in the method of mixtures.

  • I measure the metre-bridge balance length from the end where X is connected.

  • I don't confuse the V–I slope (R) with the I–V slope (1/R).

  • I can find the Zener current by subtracting the load current from the series current.

Mock Test 2: New-pattern paper

Time: 35 minutes. Marking: +4 for a correct answer, −1 for a wrong one. Take g = 10 m/s² and c_water = 4200 J kg⁻¹ K⁻¹.

1. Vernier callipers have 1 MSD = 1 mm and 25 VSD = 24 MSD. The zero error is +0.08 mm. With MSR = 12 mm and the 7th vernier division coinciding, the corrected reading is (a) 12.28 mm (b) 12.20 mm (c) 12.36 mm (d) 12.07 mm

2. A screw gauge has pitch 1 mm and 100 circular divisions. With jaws closed, the circular zero is 5 divisions above the reference line. A wire gives PSR 3 mm and CSR 47. The corrected diameter is (a) 3.42 mm (b) 3.47 mm (c) 3.52 mm (d) 3.97 mm

3. Match List I (measurement) with List II (instrument).

  • List I: (A) Internal diameter of a beaker; (B) Diameter of a thin wire; (C) Apparent thickness of a glass slab; (D) First resonance length of an air column

  • List II: (i) Travelling microscope; (ii) Metre scale; (iii) Screw gauge; (iv) Vernier callipers

(a) A-iii, B-iv, C-i, D-ii (b) A-iv, B-iii, C-ii, D-i (c) A-iv, B-i, C-iii, D-ii (d) A-iv, B-iii, C-i, D-ii

4. How many of the following statements are correct?

  • A. In Searle's apparatus, the reference wire carries a fixed weight only to keep it taut.

  • B. Adding detergent to water reduces its capillary rise.

  • C. Terminal velocity of a ball does not depend on the density of the liquid.

  • D. A² vs t for a damped pendulum is a straight line.

(a) One (b) Two (c) Three (d) Four

5. Assertion (A): In the resonance tube experiment, v = 2f(l₂ − l₁) is preferred over v = 4fl₁. Reason (R): The difference l₂ − l₁ does not contain the end correction. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

6. In a Young's modulus experiment, the percentage errors are 0.1% in L, 1% in r and 2% in ℓ; the load is exact. The maximum percentage error in Y is (a) 4.1% (b) 3.1% (c) 5.1% (d) 2.1%

7. Water (T = 0.07 N/m, θ = 0, ρ = 1000 kg/m³) rises in a clean glass tube of radius 0.5 mm. The height of rise is (a) 1.4 cm (b) 5.6 cm (c) 2.8 cm (d) 28 cm

8. For steel balls of different radii falling through an oil, a graph of terminal velocity v against r² is a straight line of slope 1.0 × 10⁴ m⁻¹ s⁻¹. If (ρ − σ) = 6000 kg/m³, the viscosity of the oil is about (a) 0.67 Pa s (b) 1.33 Pa s (c) 2.67 Pa s (d) 13.3 Pa s

9. A pendulum's amplitude falls from 10 cm to 8 cm over some swings. The fraction of its energy lost is (a) 64% (b) 20% (c) 40% (d) 36%

10. A tuning fork of 340 Hz is used with a resonance tube (v = 340 m/s). The first resonance is at 24 cm. The second resonance will be at (a) 74 cm (b) 72 cm (c) 75 cm (d) 76 cm

Passage for Q11–12: A copper calorimeter of mass 0.10 kg (specific heat 400 J kg⁻¹ K⁻¹) holds 0.15 kg of water at 25 °C. A 0.05 kg solid at 95 °C is dropped in. The final steady temperature is 30 °C. Ignore heat loss.

11. The heat gained by the calorimeter and water is (a) 3150 J (b) 3350 J (c) 3550 J (d) 200 J

12. The specific heat of the solid is about (a) 969 J kg⁻¹ K⁻¹ (b) 1340 J kg⁻¹ K⁻¹ (c) 1031 J kg⁻¹ K⁻¹ (d) 2062 J kg⁻¹ K⁻¹

13. Choose the correct set of statements.

  • A. In a metre bridge, X/R = l/(100 − l), with l from the X end.

  • B. In the half-deflection method, G = RS/(R − S).

  • C. In an Ohm's law circuit, the ammeter is connected in parallel with the wire.

  • D. Figure of merit is measured in ampere per division.

(a) A and B only (b) B and C only (c) C and D only (d) A, B and D only

14. In a metre bridge, X is in the left gap and R = 12 Ω in the right gap. The null point is at 60 cm from the left end. X equals (a) 8 Ω (b) 12 Ω (c) 20 Ω (d) 18 Ω

15. The I–V graph of a wire (length 2.0 m, cross-section 1.0 × 10⁻⁷ m²) is a straight line through the origin with slope 0.25 A/V. The resistivity of its material is (a) 8 × 10⁻⁷ Ω m (b) 5 × 10⁻⁸ Ω m (c) 2 × 10⁻⁷ Ω m (d) 1 × 10⁻⁶ Ω m

16. Assertion (A): In the half-deflection method, a high resistance R is placed in series with the galvanometer. Reason (R): A high R makes G exactly equal to the shunt S. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

17. A galvanometer (G = 100 Ω) has a figure of merit of 10 μA/division and 50 divisions for full scale. The shunt needed to make it an ammeter of range 1 A is about (a) 0.5 Ω (b) 0.05 Ω (c) 5 Ω (d) 0.005 Ω

18. Match List I (optics set-up) with List II (observation).

  • List I: (A) Concave mirror, object at C; (B) Convex lens, object at F; (C) Mark under a glass slab; (D) Prism at minimum deviation

  • List II: (i) Ray inside the prism is parallel to the base; (ii) Image at infinity; (iii) Real, inverted, same-size image at C; (iv) Mark appears raised

(a) A-iii, B-ii, C-iv, D-i (b) A-ii, B-iii, C-i, D-iv (c) A-iii, B-iv, C-ii, D-i (d) A-i, B-ii, C-iv, D-iii

19. With a convex lens, an object pin at 25 cm gives a parallax-free real image at 100 cm (both magnitudes). The focal length is (a) 25 cm (b) 40 cm (c) 20 cm (d) 75 cm

20. The lowest point of the i–δ curve for a 60° prism is at δ = 38.9°. The refractive index of the prism is about (a) 1.33 (b) 1.52 (c) 1.48 (d) 1.65

21. A glass slab of real thickness 3.000 cm and n = 1.5 is placed over a mark. The microscope reads R₁ = 1.000 cm on the mark without the slab. The reading R₂ on the mark seen through the slab is (a) 3.000 cm (b) 1.500 cm (c) 2.000 cm (d) 2.500 cm

22. How many of these statements about the i–δ graph of a prism are correct?

  • A. It has a single minimum.

  • B. Each δ larger than δm occurs at two values of i.

  • C. At δm, the angle of incidence equals the angle of emergence.

  • D. The curve is perfectly symmetric about its minimum.

(a) Two (b) Four (c) One (d) Three

23. A silicon diode carries 10 mA at 0.68 V and 30 mA at 0.72 V. Its dynamic resistance in this range is (a) 2 Ω (b) 24 Ω (c) 36 Ω (d) 0.5 Ω

24. A 6 V Zener is fed from 15 V through a 300 Ω resistor, with a 600 Ω load across it. The Zener current is (a) 30 mA (b) 10 mA (c) 20 mA (d) 50 mA

25. Assertion (A): An LED can be picked out from a group of ordinary diodes with a simple battery test. Reason (R): An LED emits light when it is forward biased. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

Passage for Q26–27: A wire of length 1.0 m and diameter 0.40 mm sits in the left gap of a metre bridge. A 10 Ω resistor is in the right gap. The null point is at 25.0 cm from the left end.

26. The resistance of the wire is (a) 3.33 Ω (b) 30 Ω (c) 7.5 Ω (d) 2.5 Ω

27. The resistivity of the wire's material is about (a) 1.05 × 10⁻⁷ Ω m (b) 1.68 × 10⁻⁶ Ω m (c) 4.19 × 10⁻⁷ Ω m (d) 1.33 × 10⁻⁶ Ω m

28. With a fixed fork, the first resonance length (ignore end correction) is 25.0 cm at 27 °C. At 127 °C, it becomes about (a) 28.9 cm (b) 33.3 cm (c) 25.0 cm (d) 21.7 cm

29. A 120 g metre scale has its centre of gravity at 50 cm. It is placed on a knife-edge at 60 cm, and an unknown mass hung at 90 cm keeps it balanced. The unknown mass is (a) 60 g (b) 30 g (c) 80 g (d) 40 g

30. A steel ball falls through oil at a terminal velocity of 2.0 cm/s. A ball of the same steel with half the radius falls through another oil of half the viscosity and the same density. Its terminal velocity is (a) 0.5 cm/s (b) 1.0 cm/s (c) 2.0 cm/s (d) 4.0 cm/s

Mock Test 2 answer key

QAnsReason
1bLC = 1/25 = 0.04 mm; 12 + 0.28 = 12.28; 12.28 − 0.08 = 12.20 mm
2cError −0.05 mm; 3.47 + 0.05 = 3.52 mm
3dVernier inside, screw gauge wire, microscope slab, metre scale air column
4bA and B true; v depends on (ρ − σ); A² vs t is a decaying curve
5aSubtracting the two lengths cancels e, which is why the method is preferred
6a0.1 + 2 × 1 + 2 = 4.1%
7ch = 2 × 0.07/(0.5 × 10⁻³ × 1000 × 10) = 0.028 m
8bη = 2(ρ − σ)g/(9 × slope) = 120000/90000 ≈ 1.33 Pa s
9dE ∝ A²: (8/10)² = 0.64, so 36% lost
10aλ = 1 m; l₁ + e = 25 cm gives e = 1 cm; l₂ = 75 − 1 = 74 cm
11b(0.10 × 400 + 0.15 × 4200) × 5 = 670 × 5 = 3350 J
12cc = 3350/(0.05 × 65) ≈ 1031 J kg⁻¹ K⁻¹
13dAn ammeter always goes in series
14dX = 12 × 60/40 = 18 Ω
15cR = 1/0.25 = 4 Ω; ρ = RA/L = 4 × 10⁻⁷/2 = 2 × 10⁻⁷ Ω m
16cHigh R limits current; G = RS/(R − S) is only close to S, not equal
17bI_g = 0.5 mA; S = 0.5 × 10⁻³ × 100/(1 − 0.0005) ≈ 0.05 Ω
18aObject at C images at C; at F, image at infinity; slab raises mark; δm ray parallel to base
19c1/f = 1/25 + 1/100 = 5/100, so f = 20 cm
20bn = sin(49.45°)/sin 30° ≈ 1.52
21cShift = 3(1 − 1/1.5) = 1.0 cm; R₂ = 1.000 + 1.000 = 2.000 cm
22dA, B, C true; the curve is not symmetric
23ar_d = 0.04 V/0.020 A = 2 Ω
24cI_s = 9/300 = 30 mA; I_L = 6/600 = 10 mA; I_Z = 20 mA
25aThe glow in forward bias is what identifies the LED
26aX = 10 × 25/75 = 3.33 Ω
27cρ = 3.33 × π(0.2 × 10⁻³)²/1.0 ≈ 4.19 × 10⁻⁷ Ω m
28al ∝ v ∝ √T: 25 × √(400/300) ≈ 28.9 cm
29dAbout 60 cm: m × 30 = 120 × 10, so m = 40 g
30bv ∝ r²/η: (1/4)/(1/2) = 1/2; 2.0 × 0.5 = 1.0 cm/s
15 min left
‹
›