Chapter 3 of 10 · 29 min read

Chapter 1: Measuring Instruments

What you will learn

  • How to find the least count of vernier callipers and a screw gauge from their scales.

  • How to take a reading and correct it for positive or negative zero error.

  • How to measure the external diameter, internal diameter and depth of a vessel.

  • How to measure the diameter of a wire and the thickness of a sheet, and avoid backlash.

  • How to find an unknown mass with a metre scale balanced on a knife edge.

Book 1 explained why a vernier works. Here we use the instruments the way you would on a lab bench, and practise the readings NEET loves to ask.

1.1 Vernier callipers: parts and least count

Vernier callipers have a fixed main scale and a sliding vernier scale. Three pairs of contacts measure three different things.

PartWhat it measuresHow you use it
Lower (outside) jawsExternal diameter, lengthGrip the object gently between the jaws
Upper (inside) jawsInternal diameterPut the jaws inside the vessel and open them till they touch the inner wall
Thin strip (depth rod) at the backDepthRest the end of the main scale on the rim, slide till the strip touches the bottom
Locking screwHolds the vernier stillTighten before you read

If n vernier divisions (VSD) equal (n − 1) main scale divisions (MSD), the least count (LC) is the difference between one MSD and one VSD.

LC=1 MSD−1 VSD=1 MSDn\text{LC} = 1\,\text{MSD} - 1\,\text{VSD} = \frac{1\,\text{MSD}}{n}

With 1 MSD = 1 mm and 10 VSD = 9 MSD, LC = 0.1 mm = 0.01 cm.

Worked example 1.1: A vernier has 20 divisions that match 19 main scale divisions. Each main scale division is 1 mm. Find the least count.

Solution: 1 VSD = 19/20 mm = 0.95 mm. LC = 1 − 0.95 = 0.05 mm = 0.005 cm.

1.2 Zero error and taking a reading

Close the jaws fully before measuring. The vernier zero should sit exactly on the main scale zero. If it does not, the instrument has a zero error.

  • Positive zero error: vernier zero lies to the right of the main scale zero. Zero error = + (coinciding vernier division) × LC.

  • Negative zero error: vernier zero lies to the left. If the k-th division coincides on a scale of n divisions, zero error = − (n − k) × LC.

A reading has two parts. The main scale reading (MSR) is the main scale mark just before the vernier zero. The vernier scale reading (VSR) is the number of the vernier division that lines up best with any main scale mark.

Observed reading=MSR+VSR×LC\text{Observed reading} = \text{MSR} + \text{VSR} \times \text{LC}
Corrected reading=Observed reading−(zero error with its sign)\text{Corrected reading} = \text{Observed reading} - (\text{zero error with its sign})

Think of a weighing scale at a sabziwala that already shows 50 g with nothing on it. Every weight it shows is 50 g too much, so you subtract 50 g. A negative zero error works the other way: you add.

Worked example 1.2: With the jaws closed, the vernier zero is to the left of the main zero and the 7th vernier division coincides (10 divisions, LC = 0.01 cm). A rod then gives MSR = 3.2 cm and the 6th division coincides. Find the true length.

Solution: Zero error = −(10 − 7) × 0.01 = −0.03 cm. Observed = 3.2 + 6 × 0.01 = 3.26 cm. Corrected = 3.26 − (−0.03) = 3.29 cm.

1.3 Experiment: Diameters and depth of a vessel with vernier callipers

Aim: To measure the external diameter, internal diameter and depth of a beaker or small vessel.

Apparatus: Vernier callipers, beaker (or a steel tumbler, a small katori works too), magnifying lens.

Principle and formula: Readings are taken as MSR + VSR × LC and corrected for zero error. From the readings you can get:

t=Dext−Dint2,V=πDint24 ht = \frac{D_{\text{ext}} - D_{\text{int}}}{2}, \qquad V = \frac{\pi D_{\text{int}}^{2}}{4}\, h

Here t is wall thickness, V the internal volume (capacity) and h the depth.

Procedure:

  1. Find the LC. Close the jaws and note the zero error with its sign.

  2. Place the vessel between the lower jaws. Close them gently and lock.

  3. Note MSR and VSR. Repeat at three or four places, turning the vessel each time.

  4. Insert the upper jaws inside the mouth. Open them till they press lightly on the inner wall. Read as before, at several places.

  5. Rest the end of the main scale on the rim. Slide the vernier till the depth strip just touches the bottom. Read. Repeat at different points on the rim.

  6. Take the mean of each set and correct for zero error.

Observation table layout:

S. No.QuantityMSR (cm)Coinciding VSDVSR × LC (cm)Observed (cm)Corrected (cm)
1–3External diameter
4–6Internal diameter
7–9Depth

Result: External diameter = … cm, internal diameter = … cm, depth = … cm (each to the LC).

Precautions:

  • Do not press the jaws hard. The vessel may deform and the scale may wear.

  • Hold the eye directly above the coinciding mark to avoid parallax.

  • For internal diameter, place the jaws across the widest chord (a true diameter), not a smaller chord.

  • Keep the depth strip vertical.

Sources of error:

  • Zero error not noted, or taken with the wrong sign.

  • The vessel may not be perfectly circular, so a single reading misleads.

  • A rim that is not flat gives a wrong depth.

Viva-style points:

  • The upper jaws read internal diameter directly, because the jaws are ground so that their outer edges line up with the zero.

  • A larger n means a smaller LC and better precision.

  • If no vernier mark lines up exactly, take the one that looks closest.

Worked example 1.3: A steel tumbler gives a corrected external diameter of 5.48 cm and an internal diameter of 5.12 cm. Find the wall thickness.

Solution: t = (5.48 − 5.12)/2 = 0.36/2 = 0.18 cm.

Worked example 1.4: A beaker has internal diameter 4.00 cm and depth 6.00 cm. Find its capacity.

Solution: r = 2.00 cm. V = π × (2.00)² × 6.00 = π × 24.0 = 75.4 cm³, so about 75 mL.

1.4 Screw gauge: pitch, least count, zero error, backlash

A screw gauge has a linear (pitch) scale on the sleeve and a circular scale on the thimble. One full turn moves the spindle forward by one pitch.

Pitch=distance moved on linear scalenumber of full rotations,LC=pitchnumber of circular divisions\text{Pitch} = \frac{\text{distance moved on linear scale}}{\text{number of full rotations}}, \qquad \text{LC} = \frac{\text{pitch}}{\text{number of circular divisions}}

Pitch 1 mm with 100 divisions, or pitch 0.5 mm with 50 divisions, both give LC = 0.01 mm.

Zero error. Turn the ratchet till the studs just touch.

  • If the zero of the circular scale is below the reference (index) line, the error is positive. Zero error = + (division on the line) × LC.

  • If the zero is above the line, the error is negative. Zero error = − (N − division on the line) × LC, where N is the number of circular divisions.

Observed reading=PSR+CSR×LC\text{Observed reading} = \text{PSR} + \text{CSR} \times \text{LC}

Backlash error. Worn threads leave a little play between screw and nut. If you reverse the direction of turning, the spindle stays still for a moment while the thimble turns. Avoid it by always turning in one direction when you close on the object.

The ratchet. It slips once the studs grip the object with a fixed small force. This stops you from crushing a soft wire and gives the same pressure every time.

Worked example 1.5: A screw gauge has pitch 0.5 mm and 50 circular divisions. Its zero error is +3 divisions. A wire gives PSR = 2.5 mm and CSR = 34. Find the diameter.

Solution: LC = 0.5/50 = 0.01 mm. Observed = 2.5 + 34 × 0.01 = 2.84 mm. Zero error = +0.03 mm. Corrected = 2.84 − 0.03 = 2.81 mm.

Worked example 1.6: Pitch 1 mm, 100 divisions. With the studs touching, the 97th division is on the reference line and the zero is above it. A wire gives PSR = 1 mm, CSR = 24. Find the diameter.

Solution: LC = 0.01 mm. Zero error = −(100 − 97) × 0.01 = −0.03 mm. Observed = 1 + 0.24 = 1.24 mm. Corrected = 1.24 + 0.03 = 1.27 mm.

1.5 Experiment: Diameter of a wire and thickness of a sheet with a screw gauge

Aim: To find the diameter of a thin wire, or the thickness of a thin sheet, using a screw gauge.

Apparatus: Screw gauge, wire (or a sheet such as a strip of tin or a blade-thin metal plate), magnifying lens.

Principle and formula: Diameter = PSR + CSR × LC − zero error. Cross-section area of the wire, A = πd²/4.

Procedure:

  1. Find the pitch by giving a few full turns and noting the distance moved. Find the LC.

  2. Turn the ratchet till the studs touch. Note the zero error with its sign.

  3. Place the wire between the studs. Turn only by the ratchet till it clicks.

  4. Note PSR and CSR.

  5. Turn the wire through 90° at the same place and read again. This checks for an oval cross-section.

  6. Repeat at four or five places along the length. For a sheet, read at several points spread over it.

  7. Find the mean and correct for zero error.

Observation table layout:

S. No.PSR (mm)CSR (div)CSR × LC (mm)Reading in one direction (mm)Reading at 90° (mm)Mean (mm)
1
2
3

Result: Mean corrected diameter of the wire = … mm.

Precautions:

  • Always use the ratchet, never the thimble, for the final approach.

  • Move the screw in one direction only, to avoid backlash.

  • The wire must be straight and free of kinks at the point of reading.

  • Read with the eye level with the reference line.

Sources of error:

  • Backlash in the threads.

  • Non-uniform wire, or a cross-section that is not circular.

  • Studs not clean, or the wire pressed too hard.

Viva-style points:

  • A screw gauge is about 10 times more precise than a common vernier (0.01 mm against 0.1 mm).

  • Readings at right angles at the same spot detect ovality of the wire.

  • The percentage error in area is twice the percentage error in diameter, since A depends on d².

1.6 Experiment: Mass of an object using a metre scale (principle of moments)

Aim: To find the mass of a given object using a metre scale balanced on a knife edge.

Apparatus: Metre scale, knife edge (a sharp wedge), known mass (say 50 g or 100 g), the unknown object (a stone or a lock), two thread loops.

Principle and formula: When a body is balanced, the total clockwise moment about the fulcrum equals the total anticlockwise moment. Balance the scale alone first; that point is its centre of gravity G. Keep the knife edge at G. Then the scale's own weight has no moment.

m g d1=M g d2    ⇒    m=Md2d1m \, g \, d_{1} = M \, g \, d_{2} \;\;\Rightarrow\;\; m = \frac{M d_{2}}{d_{1}}

Here d₁ and d₂ are distances of the unknown mass m and known mass M from the knife edge.

If the knife edge is not at G, the scale's weight W acts at G and adds a moment W × (distance of G from the knife edge).

Procedure:

  1. Balance the empty scale on the knife edge. Note the balance point G (ideally 50.0 cm).

  2. Keep the knife edge at G. Hang the unknown object on one side by a thread loop.

  3. Hang the known mass on the other side. Slide it till the scale is horizontal again.

  4. Note d₁ and d₂ from the knife edge.

  5. Repeat for three different positions of the unknown object. Find m each time and take the mean.

Observation table layout:

S. No.Position of knife edge (cm)Position of m (cm)Position of M (cm)d₁ (cm)d₂ (cm)m = Md₂/d₁ (g)
1
2
3

Result: Mass of the object = … g.

Precautions:

  • The knife edge must be sharp and the threads thin and light.

  • Check that the scale is truly horizontal and at rest before reading.

  • Keep the loops perpendicular to the scale, so the distances are measured along the scale.

  • Do not let the masses swing or touch the table.

Sources of error:

  • Weight of the thread loops ignored.

  • Knife edge not exactly at G.

  • Air currents (a ceiling fan running) disturb the balance.

Viva-style points:

  • This is a lever of the first class: fulcrum between effort and load.

  • Larger distances give smaller percentage error in each distance.

  • The mass found is independent of g, because g cancels on both sides.

Worked example 1.7: A metre scale balances at 50.0 cm. A stone hung at the 20.0 cm mark is balanced by a 50 g mass at the 74.0 cm mark. Find the mass of the stone.

Solution: d₁ = 50.0 − 20.0 = 30.0 cm. d₂ = 74.0 − 50.0 = 24.0 cm. m = 50 × 24.0/30.0 = 40 g.

Worked example 1.8: A uniform metre scale of mass 100 g balances at 50 cm. The knife edge is moved to the 40 cm mark. What mass hung at the 10 cm mark makes the scale balance again?

Solution: The scale's weight acts at 50 cm, 10 cm to the right of the knife edge. The unknown mass is 30 cm to the left. m × 30 = 100 × 10, so m = 33.3 g.

Quick revision

  • Vernier LC = 1 MSD − 1 VSD = 1 MSD/n. Screw gauge LC = pitch/number of circular divisions.

  • Corrected reading = observed − zero error (zero error keeps its sign).

  • Vernier: lower jaws for external size, upper jaws for internal diameter, strip for depth.

  • Screw gauge: zero below the reference line = positive error; above = negative error.

  • Use the ratchet; turn in one direction only to avoid backlash.

  • Metre scale: knife edge at G, then m d₁ = M d₂.

  • Wall thickness = (external − internal diameter)/2.

NEET traps

  • Adding a positive zero error instead of subtracting it. The rule is always "subtract the signed zero error".

  • For a negative zero error, writing −k × LC instead of −(n − k) × LC.

  • Forgetting that pitch can be 0.5 mm, so each PSR division is 0.5 mm, not 1 mm.

  • Halving the wrong quantity: wall thickness needs half the difference of diameters, not the full difference.

  • Ignoring the scale's own weight when the knife edge is not at the centre of gravity.

  • Writing a screw gauge reading to 0.1 mm or 0.001 mm instead of to its LC of 0.01 mm.

Practice MCQs: Chapter 1

Level 1: Concept check

1. In vernier callipers, 10 vernier divisions equal 9 main scale divisions and 1 MSD = 1 mm. The least count is (a) 0.01 mm (b) 0.1 mm (c) 0.9 mm (d) 1 mm

2. Which part of vernier callipers is used to measure the depth of a beaker? (a) Lower jaws (b) Upper jaws (c) Thin strip at the back (d) Locking screw

3. The internal diameter of a steel tumbler is measured with the (a) upper (inside) jaws (b) lower (outside) jaws (c) depth strip (d) main scale alone

4. A screw gauge has pitch 1 mm and 100 circular divisions. Its least count is (a) 0.1 mm (b) 0.001 mm (c) 1 mm (d) 0.01 mm

5. The ratchet of a screw gauge is used (a) to grip the object with the same small force every time (b) to remove zero error (c) to change the pitch (d) to read the linear scale

6. Vernier callipers have a positive zero error when, with the jaws closed, the vernier zero lies (a) to the left of the main scale zero (b) to the right of the main scale zero (c) exactly on the main scale zero (d) on the last main scale mark

7. The corrected reading of any instrument is (a) observed + zero error (b) observed × zero error (c) observed − least count (d) observed − zero error, with the error's sign

8. Backlash error in a screw gauge is avoided by (a) using a larger least count (b) cleaning the studs (c) turning the screw in one direction only while closing on the object (d) reading the wire at 90°

9. The metre scale method of finding mass is based on (a) net force being zero only (b) clockwise moments equalling anticlockwise moments about the fulcrum (c) mass being proportional to length (d) torque being proportional to angular velocity

10. The diameter of a wire is read twice at the same spot, at right angles to each other. This is done (a) to detect a cross-section that is not circular (b) to remove zero error (c) to avoid backlash (d) to find the pitch

Level 2: NEET standard

11. A vernier has 1 MSD = 0.5 mm and 25 vernier divisions equal 24 main scale divisions. The least count is (a) 0.05 mm (b) 0.01 mm (c) 0.02 mm (d) 0.2 mm

12. Vernier callipers (LC 0.01 cm) have a zero error of +0.02 cm. A rod gives MSR = 2.4 cm and the 7th vernier division coincides. The true length is (a) 2.49 cm (b) 2.47 cm (c) 2.43 cm (d) 2.45 cm

13. With the jaws closed, the vernier zero lies left of the main zero and the 6th of 10 vernier divisions coincides. LC = 0.1 mm. The zero error is (a) −0.4 mm (b) −0.6 mm (c) +0.6 mm (d) +0.4 mm

14. A screw gauge with pitch 0.5 mm and 50 circular divisions has no zero error. PSR = 3.5 mm and CSR = 18. The reading is (a) 3.518 mm (b) 3.68 mm (c) 3.86 mm (d) 5.30 mm

15. In a screw gauge (LC 0.01 mm), with the studs touching, the zero of the circular scale is 5 divisions below the reference line. A wire reads 1.86 mm. Its true diameter is (a) 1.91 mm (b) 1.36 mm (c) 1.81 mm (d) 1.86 mm

16. A screw gauge has 100 circular divisions and LC 0.01 mm. With the studs touching, the 95th division is on the reference line and the zero is above it. A wire reads 2.37 mm. Its true diameter is (a) 2.32 mm (b) 1.42 mm (c) 2.37 mm (d) 2.42 mm

17. A vessel has external diameter 6.24 cm and internal diameter 5.86 cm. Its wall thickness is (a) 0.38 cm (b) 0.19 cm (c) 0.76 cm (d) 0.095 cm

18. A cylindrical beaker has internal diameter 5.0 cm and depth 8.0 cm. Its capacity is about (a) 157 cm³ (b) 628 cm³ (c) 200 cm³ (d) 39.3 cm³

19. A metre scale balances at 50 cm. A stone at the 15 cm mark is balanced by 100 g at the 80 cm mark. The mass of the stone is (a) 116.7 g (b) 100 g (c) 85.7 g (d) 42.9 g

20. A uniform metre scale of mass 120 g is balanced on a knife edge at the 30 cm mark by hanging an unknown mass at the 10 cm mark. The unknown mass is (a) 60 g (b) 240 g (c) 40 g (d) 120 g

21. The sleeve of a screw gauge is marked in millimetres. The thimble has 50 divisions, and the spindle moves one sleeve division in two full turns. The least count is (a) 0.02 mm (b) 0.01 mm (c) 0.005 mm (d) 0.1 mm

22. A screw gauge (LC 0.01 mm, no zero error) gives the thickness of a sheet as 0.52, 0.54, 0.53 and 0.56 mm at four spots. The value to report is (a) 0.5375 mm (b) 0.53 mm (c) 0.54 mm (d) 0.55 mm

Level 3: Challenge

23. A vernier is built with n vernier divisions equal to (n − 1) main scale divisions of 1 mm each. If its least count is 0.05 mm, n is (a) 20 (b) 10 (c) 50 (d) 5

24. A screw gauge has pitch 0.5 mm and 50 circular divisions. With the studs touching, the circular zero is 3 divisions below the reference line. For a wire, the linear scale shows 4 half-millimetre divisions and CSR = 46. The diameter is (a) 2.49 mm (b) 4.43 mm (c) 2.46 mm (d) 2.43 mm

25. A wire's diameter is found to be 0.80 mm. Its area of cross-section is (a) 2.01 × 10⁻⁶ m² (b) 2.51 × 10⁻⁷ m² (c) 5.03 × 10⁻⁷ m² (d) 5.03 × 10⁻⁶ m²

26. A uniform metre scale balances at its 50 cm mark. When the knife edge is shifted to the 40 cm mark, a 20 g mass hung at the 10 cm mark keeps it balanced. The mass of the scale is (a) 20 g (b) 60 g (c) 80 g (d) 120 g

27. The diameter of a wire is 0.50 mm, measured with a screw gauge of LC 0.01 mm. The maximum percentage error in its area of cross-section is (a) 4% (b) 2% (c) 1% (d) 8%

28. A cylindrical vessel has internal diameter 7.00 cm and depth 10.00 cm, both measured with vernier callipers. Its capacity is about (a) 1540 mL (b) 220 mL (c) 70 mL (d) 385 mL

29. Assertion (A): While measuring a wire, the screw of a screw gauge should be turned in one direction only. Reason (R): Wear in the threads leaves some play between the screw and the nut. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: Vernier callipers can measure the depth of a beaker. Statement II: The internal diameter of a beaker is measured with the lower jaws of vernier callipers. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1bLC = 1 mm/10 = 0.1 mm
2cThe depth strip slides out from the back end
3aUpper jaws press on the inner wall
4d1 mm/100 = 0.01 mm
5aRatchet slips at a fixed small force
6bVernier zero to the right means the scale already reads more than zero
7dSubtract the signed zero error
8cReversing direction brings in the play of the threads
9bBalance means equal and opposite moments
10aTwo perpendicular readings reveal an oval section
11cLC = 0.5 mm/25 = 0.02 mm
12d2.4 + 0.07 − 0.02 = 2.45 cm
13a−(10 − 6) × 0.1 = −0.4 mm
14b3.5 + 18 × 0.01 = 3.68 mm
15cError +0.05 mm; 1.86 − 0.05 = 1.81 mm
16dError −0.05 mm; 2.37 + 0.05 = 2.42 mm
17b(6.24 − 5.86)/2 = 0.19 cm
18aπ × 2.5² × 8 = 157 cm³
19cm × 35 = 100 × 30, m = 85.7 g
20dm × 20 = 120 × 20, m = 120 g
21bPitch 0.5 mm; 0.5/50 = 0.01 mm
22cMean 0.5375 mm, rounded to LC gives 0.54 mm
23aLC = 1 mm/n = 0.05 mm, so n = 20
24d2.0 + 0.46 − 0.03 = 2.43 mm
25cπ × (0.4 × 10⁻³)² = 5.03 × 10⁻⁷ m²
26b20 × 30 = M × 10, M = 60 g
27a2 × (0.01/0.50) × 100 = 4%
28dπ × 3.5² × 10 = 385 cm³
29aPlay in threads is exactly why direction must not reverse
30cInternal diameter needs the upper jaws

Chapter 1 revision sheet

One-page summary

  • Vernier least count: LC = 1 MSD − 1 VSD. If n VSD = (n − 1) MSD, LC = 1 MSD/n.

  • Vernier reading = MSR + (VSR × LC). MSR is the main-scale mark just before the vernier zero.

  • Lower (outside) jaws give external size, upper (inside) jaws give internal diameter, the strip gives depth.

  • Vernier zero error is positive when the vernier zero lies right of the main-scale zero. Positive error = k × LC, where k is the coinciding division.

  • Negative vernier error = −(n − k) × LC when the vernier zero lies left of the main-scale zero.

  • Corrected reading = observed reading − zero error, with the error's own sign.

  • Screw gauge: pitch = distance moved in one full turn; LC = pitch/number of circular divisions.

  • Screw gauge reading = PSR + (CSR × LC).

  • Circular zero below the reference line (jaws closed) gives a positive error; above it gives a negative error.

  • Backlash: worn threads make the screw slip; turn in one direction only. The ratchet gives the same gentle pressure every time.

  • Wall thickness of a hollow cylinder = (external − internal diameter)/2. Inner volume = π(D/2)² × depth.

  • Metre-scale moments: balance the scale alone first to find its centre of gravity G. Then m d₁ = M d₂ about the knife-edge.

  • If the knife-edge is not at G, the scale's own weight adds a moment W × (distance of G from knife-edge).

  • Always record readings to the least count of the instrument.

Must-remember table

QuantityFormula or valueTypical lab value
Vernier LC1 MSD/n0.1 mm (10 div) or 0.02 mm (50 div), 1 MSD = 1 mm
Screw gauge LCpitch/N0.5 mm/50 = 0.01 mm
Vernier readingMSR + VSR × LCin cm or mm
Screw gauge readingPSR + CSR × LCin mm
Corrected readingobserved − zero errorerror keeps its sign
Wall thickness(D_ext − D_int)/2in cm
Moments balancem d₁ = M d₂distances from knife-edge
% error in volume of wire2(Δd/d) + ΔL/Ldiameter term doubled

Memory aids

  • "Right is Plus, Below is Plus": vernier zero to the Right of main zero = Positive; circular zero Below the reference line = Positive.

  • "LUD" for the vernier jaws: Lower jaws = outside size, Upper jaws = inside diameter, Depth strip = depth.

  • "Pitch per Piece": LC of a screw gauge = pitch divided by the number of pieces (circular divisions).

  • "Subtract the Sign": corrected = observed − (zero error with its sign), so a negative error gets added.

  • "One Way, Ratchet Stay": turn the screw one way only (no backlash) and stop at the ratchet click (no over-pressing).

Concept connections

  • Least count, significant figures and error propagation come from Physics Book 1: Physics and Measurement.

  • The metre-scale experiment uses torque balance from Physics Book 5: Rotational Motion.

  • Screw gauge and vernier readings feed every later experiment here: wire radius for Young's modulus (Chapter 2) and resistivity (Chapter 4).

Practice MCQs: Chapter 1, Level 4 (new NEET pattern)

31. Match List I (instrument data) with List II (least count).

  • List I: (A) Vernier, 1 MSD = 1 mm, 20 VSD = 19 MSD; (B) Screw gauge, pitch 0.5 mm, 50 circular divisions; (C) Vernier, 1 MSD = 1 mm, 10 VSD = 9 MSD; (D) Screw gauge, pitch 1 mm, 200 circular divisions

  • List II: (i) 0.005 mm; (ii) 0.01 mm; (iii) 0.05 mm; (iv) 0.1 mm

(a) A-ii, B-iii, C-i, D-iv (b) A-iii, B-ii, C-iv, D-i (c) A-iv, B-i, C-iii, D-ii (d) A-iii, B-iv, C-ii, D-i

32. Match List I (part) with List II (use).

  • List I: (A) Lower jaws of vernier; (B) Upper jaws of vernier; (C) Depth strip of vernier; (D) Ratchet of screw gauge

  • List II: (i) Depth of a beaker; (ii) Internal diameter of a ring; (iii) Same gentle pressure on the object every time; (iv) External diameter of a rod

(a) A-ii, B-iv, C-iii, D-i (b) A-iv, B-i, C-ii, D-iii (c) A-i, B-ii, C-iv, D-iii (d) A-iv, B-ii, C-i, D-iii

33. Match List I (jaws closed) with List II (zero error).

  • List I: (A) Vernier, LC 0.1 mm, 10 VSD; vernier zero right of main zero, 4th VSD coincides; (B) Same vernier; vernier zero left of main zero, 6th VSD coincides; (C) Screw gauge, LC 0.01 mm; circular zero 3 divisions below reference line; (D) Same screw gauge; circular zero 3 divisions above reference line

  • List II: (i) −0.03 mm; (ii) +0.4 mm; (iii) +0.03 mm; (iv) −0.4 mm

(a) A-ii, B-iv, C-iii, D-i (b) A-iv, B-ii, C-i, D-iii (c) A-ii, B-i, C-iii, D-iv (d) A-iii, B-iv, C-ii, D-i

34. Match List I (problem) with List II (remedy).

  • List I: (A) Backlash error; (B) Parallax in reading a scale; (C) Wire not perfectly uniform; (D) Scale's centre of gravity unknown in the moments experiment

  • List II: (i) Balance the scale alone on the knife-edge first; (ii) Keep the eye normal to the scale; (iii) Turn the screw in one direction only; (iv) Measure at several places in two perpendicular directions

(a) A-ii, B-iii, C-i, D-iv (b) A-iii, B-iv, C-ii, D-i (c) A-iii, B-ii, C-iv, D-i (d) A-i, B-ii, C-iv, D-iii

35. How many of the following statements are correct?

  • A. Least count of vernier callipers = 1 MSD − 1 VSD.

  • B. A negative zero error gets added to the observed reading to give the corrected reading.

  • C. Keeping the pitch fixed, more circular divisions give a larger least count.

  • D. A screw gauge of LC 0.01 mm is less precise than vernier callipers of LC 0.1 mm.

(a) Only one (b) Only two (c) Only three (d) All four

36. Choose the correct set of statements about finding mass with a metre scale.

  • A. The scale is first balanced alone to locate its centre of gravity.

  • B. With the knife-edge at G, m d₁ = M d₂, where d₁ and d₂ are distances of m and M from the knife-edge.

  • C. The method works only if the knife-edge is exactly at the 50 cm mark.

  • D. With the knife-edge at G, the mass of the scale does not enter the equation.

(a) A, B and D only (b) A and C only (c) B, C and D only (d) C and D only

37. How many of these statements about a screw gauge are correct?

  • A. Pitch is the distance the spindle moves in one full rotation.

  • B. The ratchet stops the user from pressing the object too hard.

  • C. Backlash error is removed by subtracting the zero error.

  • D. If the circular zero is below the reference line with jaws closed, the error is negative.

(a) One (b) Three (c) Four (d) Two

38. Choose the correct set of statements for a beaker measured with vernier callipers.

  • A. Wall thickness = (external diameter − internal diameter)/2.

  • B. Inner volume = π × (internal diameter/2)² × depth.

  • C. Depth is measured with the upper jaws.

  • D. Each reading is written to the least count of the callipers.

(a) A and C only (b) B, C and D only (c) A, B and D only (d) All four

39. A screw gauge (LC 0.01 mm) has a zero error of −0.02 mm. Three readings on a wire are: PSR 1 mm with CSR 23, PSR 1 mm with CSR 25, and PSR 1 mm with CSR 21. The corrected mean diameter is (a) 1.25 mm (b) 1.23 mm (c) 1.21 mm (d) 1.27 mm

40. In the metre-scale experiment (knife-edge at G), an unknown mass m and a 50 g mass hang on opposite sides. Each time m is shifted, the 50 g mass is moved to rebalance. A graph of d₂ (distance of the 50 g mass) against d₁ (distance of m) is a straight line through the origin with slope 0.8. The value of m is (a) 62.5 g (b) 40 g (c) 50 g (d) 0.8 g

41. Vernier callipers have 1 MSD = 0.5 mm and 50 VSD = 49 MSD. With no zero error, MSR = 23.5 mm and the 18th vernier division coincides. The reading is (a) 23.59 mm (b) 24.40 mm (c) 23.518 mm (d) 23.68 mm

Passage for Q42–43: A student measures a steel ball with a screw gauge of pitch 0.5 mm and 50 circular divisions. With the jaws closed, the circular-scale zero stands 4 divisions above the reference line. With the ball held, the linear scale shows 6.5 mm and the circular scale reads 32.

42. The zero error of the gauge is (a) +0.04 mm (b) −0.04 mm (c) +0.4 mm (d) −0.4 mm

43. The corrected diameter of the ball is (a) 6.78 mm (b) 6.82 mm (c) 6.86 mm (d) 6.90 mm

44. A wire's diameter 0.50 mm is measured with a screw gauge of LC 0.01 mm, and its length 100.0 cm with a scale of LC 0.1 cm. The maximum percentage error in its volume is (a) 4.1% (b) 2.1% (c) 4.0% (d) 6.1%

45. A uniform 100 g metre scale balances alone at 50.0 cm. An unknown mass is hung at the 20.0 cm mark, and the scale now balances with the knife-edge at 40.0 cm. The unknown mass is (a) 25 g (b) 100 g (c) 200 g (d) 50 g

Level 4 answer key

QAnsReason
31bLCs: 1/20 = 0.05, 0.5/50 = 0.01, 1/10 = 0.1, 1/200 = 0.005 mm
32dLower jaws outside, upper jaws inside, strip for depth, ratchet for even pressure
33a+4 × 0.1; −(10 − 6) × 0.1; below line +3 × 0.01; above line −3 × 0.01
34cOne-way turning, normal eye, many readings, balance scale alone
35bA and B true; more divisions lower LC; smaller LC means more precise
36aKnife-edge can be anywhere at G, not necessarily 50 cm
37dA, B true; backlash is not a zero error; below the line is positive
38cDepth uses the strip, not the upper jaws
39aMean observed 1.23 mm; 1.23 − (−0.02) = 1.25 mm
40bd₂ = (m/M) d₁, so m = 0.8 × 50 = 40 g
41dLC = 0.5/50 = 0.01 mm; 23.5 + 18 × 0.01 = 23.68 mm
42bZero above the line is negative: −4 × 0.01 = −0.04 mm
43c6.5 + 0.32 = 6.82; 6.82 + 0.04 = 6.86 mm
44a2 × (0.01/0.50) × 100 + (0.1/100.0) × 100 = 4 + 0.1 = 4.1%
45dAbout 40 cm: m × 20 = 100 × 10, so m = 50 g
29 min left
‹
›
Chapter 1: Measuring | NEET Physics Book 20: Experimental…