Chapter 4 of 10 · 30 min read

Chapter 2: Mechanics and Properties of Matter

What you will learn

  • Why the energy of a swinging pendulum depends on amplitude squared, and how to read an A² vs t graph.

  • How Searle's apparatus measures Young's modulus of a wire, and why it uses two wires.

  • How capillary rise gives the surface tension of water, and what a detergent does to it.

  • How the terminal velocity of a falling ball gives the viscosity of a liquid.

  • Which measurement in each experiment carries the largest error.

2.1 Experiment: Dissipation of energy of a simple pendulum

Aim: To study the loss of energy of a simple pendulum by plotting a graph between the square of amplitude and time.

Apparatus: A heavy bob (or a bob with a light cardboard disc fixed to it to add air drag), strong thread, clamp stand, a half-metre scale or protractor fixed behind the bob, stopwatch.

Principle and formula: The energy of an oscillator is all potential at the extreme position.

E=12mω2A2    ⇒    E∝A2E = \frac{1}{2} m \omega^{2} A^{2} \;\;\Rightarrow\;\; E \propto A^{2}

So A² tracks the energy left in the pendulum. Air drag takes energy away on every swing. For a drag force proportional to speed (F = −bv):

A(t)=A0 e−bt/2m,E(t)=E0 e−bt/mA(t) = A_{0}\, e^{-bt/2m}, \qquad E(t) = E_{0}\, e^{-bt/m}

The A² vs t graph is a falling curve that flattens with time. Energy is lost fast at first, then slowly. A graph of ln A² against t is a straight line of slope −b/m. The time m/b is the time in which energy falls to 1/e (about 37%) of its starting value.

A child on a park swing shows the same thing. If nobody pushes, big swings shrink quickly, and small swings fade slowly.

Procedure:

  1. Fix the scale horizontally just behind the bob, with its centre under the rest position.

  2. Pull the bob aside by a known amplitude, say 10 cm, and release it without a push.

  3. Start the stopwatch. Note the amplitude after every 1 minute (or after every 10 oscillations).

  4. Read the extreme position by looking straight at the scale, along the thread.

  5. Continue till the amplitude becomes too small to read.

  6. Square each amplitude and plot A² on the y-axis against t on the x-axis.

Observation table layout:

S. No.Time t (s)Amplitude A (cm)A² (cm²)ln A²
10
260
3120

Graph: A² vs t falls along a decaying curve (Figure 2.1). Equal time intervals cut A² by the same fraction, not by the same amount.

Figure 2.1 · A² vs t for a damped pendulum, and ln A² vs t
Figure 2.1 · A² vs t for a damped pendulum, and ln A² vs t

A² halves in every equal interval T, so the A² curve keeps flattening while the ln A² plot stays a straight line.

Result: The energy of the pendulum, shown by A², decreases exponentially with time. The rate of energy loss falls as the amplitude falls.

Precautions:

  • Release the bob without any push, and keep the swings in one plane.

  • Keep the amplitude small, so the motion stays close to simple harmonic.

  • Read the amplitude without parallax, eye in line with the thread.

  • Keep doors closed and the ceiling fan off; stray air currents change the drag.

Sources of error:

  • Judging the exact extreme position of a moving bob is hard.

  • Friction at the point of support adds to the loss.

  • Conical (elliptical) motion of the bob.

Viva-style points:

  • The time period stays almost the same as amplitude decays (light damping).

  • A cardboard disc on the bob increases drag, so the decay is faster and easier to see.

  • Lost mechanical energy becomes heat in the air and at the support.

Worked example 2.1: A pendulum's amplitude drops from 10 cm to 5 cm in 2 minutes. What fraction of its energy has been lost?

Solution: E ∝ A². E/E₀ = (5/10)² = 1/4. Energy lost = 3/4, that is 75%.

Worked example 2.2: For a lightly damped pendulum, A² falls from 100 cm² to 50 cm² in 90 s. How long from the start until A² is 25 cm², and what is the amplitude then?

Solution: Exponential decay halves A² in equal times. 100 → 50 takes 90 s, so 50 → 25 takes another 90 s. Total time = 180 s. Amplitude = √25 = 5 cm.

2.2 Experiment: Young's modulus of a wire by Searle's method

Aim: To find the Young's modulus of elasticity of the material of a given metallic wire.

Apparatus: Searle's apparatus (two identical long wires hanging from one rigid support, with a frame carrying a spirit level and a micrometer screw), slotted 0.5 kg masses, hanger, screw gauge, metre scale.

Set-up: One wire is the reference wire. It carries a fixed load that keeps it straight. The other is the experimental wire, which carries the hanger. A spirit level rests on a bar hinged to the reference frame on one side and supported on the tip of a micrometer screw on the other. When the experimental wire stretches, the level tilts. Turning the micrometer back to level the bubble gives the extension directly (Figure 2.2).

Figure 2.2 · Searle's apparatus, schematic
Figure 2.2 · Searle's apparatus, schematic

Loading the experimental wire lowers its frame and tilts the level; the micrometer turn that relevels the bubble is the extension ℓ.

Principle and formula: Within the elastic limit, stress is proportional to strain.

Y=stressstrain=Mg/πr2ℓ/L=MgLπr2ℓY = \frac{\text{stress}}{\text{strain}} = \frac{Mg/\pi r^{2}}{\ell / L} = \frac{M g L}{\pi r^{2} \ell}

Here M is the added load, L the original length, r the radius and ℓ the extension. If you plot extension ℓ (y-axis) against load M (x-axis), the line is straight. Its slope is ℓ/M, so:

Y=gLπr2×slopeY = \frac{g L}{\pi r^{2} \times \text{slope}}

Why two wires? Both wires hang from the same support and feel the same room temperature. If the support sags or both wires expand with heat, both move equally and the level does not tilt. Only the extra stretch of the experimental wire is measured.

Procedure:

  1. Hang a dead load (say 1 kg) on the experimental wire to remove kinks. It is not counted in M.

  2. Measure L with a metre scale, from the support to the point where the frame is attached.

  3. Measure the diameter with a screw gauge at several places, in two perpendicular directions. Find the mean radius.

  4. Level the bubble with the micrometer and note the reading.

  5. Add 0.5 kg. Wait about a minute. Level the bubble again and note the reading.

  6. Repeat up to a safe maximum load. Then remove the load in the same steps and read again while unloading.

  7. Take the mean of loading and unloading readings for each load. Find the extension for each load, and plot ℓ against M.

Observation table layout:

S. No.Load M (kg)Micrometer reading, loading (mm)Micrometer reading, unloading (mm)Mean (mm)Extension ℓ (mm)
100
20.5
31.0
41.5

Graph: ℓ vs M is a straight line through the origin. A bend at large load means the elastic limit has been crossed.

Result: Young's modulus of the material = … N/m².

Precautions:

  • Keep the load well within the elastic limit (less than half the breaking load).

  • Wait a minute after each change in load before levelling, so the wire settles.

  • Use the micrometer in one direction only, to avoid backlash.

  • Both wires should be of the same material, length and thickness, and free of kinks.

Sources of error:

  • The radius is small and appears squared, so its error counts twice. This is the largest error.

  • Elastic after-effect: the wire does not return at once on unloading.

  • Slight non-uniformity of the wire.

Viva-style points:

  • Y is a property of the material, not of the length or thickness of the wire.

  • A thin, long wire gives a larger extension for the same load, so ℓ is measured more accurately.

  • Loading and unloading readings are averaged to cancel elastic lag.

Worked example 2.3: A steel wire 2.0 m long and 0.50 mm in diameter stretches by 2.0 mm under a load of 4.0 kg. Find Y. (g = 10 m/s²)

Solution: r = 0.25 × 10⁻³ m. Area = π × (0.25 × 10⁻³)² = 1.96 × 10⁻⁷ m². Y = (4.0 × 10 × 2.0)/(1.96 × 10⁻⁷ × 2.0 × 10⁻³) = 2.04 × 10¹¹ N/m².

Worked example 2.4: In a Searle's experiment the ℓ vs M graph has slope 0.25 mm/kg. The wire is 1.5 m long with diameter 0.60 mm. Find Y.

Solution: Slope = 0.25 × 10⁻³ m/kg. r = 0.30 × 10⁻³ m, so πr² = 2.83 × 10⁻⁷ m². Y = (10 × 1.5)/(2.83 × 10⁻⁷ × 0.25 × 10⁻³) = 2.12 × 10¹¹ N/m².

Worked example 2.5: In a Searle's experiment, L = 200 cm ± 0.1 cm, d = 0.50 mm ± 0.01 mm and ℓ = 1.00 mm ± 0.01 mm. Take load and g as exact. Find the maximum percentage error in Y.

Solution: %Y = %L + 2 × %d + %ℓ = 0.05 + 2 × 2 + 1 = 5.05%. The diameter alone gives 4% of it.

2.3 Experiment: Surface tension of water by capillary rise

Aim: To find the surface tension of water by the capillary rise method, and to see the effect of a detergent.

Apparatus: Clean glass capillary tube, beaker of water, stand with clamp, a bent pin (pointer), travelling microscope, a pinch of detergent.

Principle and formula: Surface tension pulls the water up the tube until the weight of the raised column balances the upward pull along the contact line.

h=2Tcos⁡θrρg    ⇒    T=rhρg2cos⁡θh = \frac{2T\cos\theta}{r \rho g} \;\;\Rightarrow\;\; T = \frac{r h \rho g}{2\cos\theta}

For pure water in clean glass, θ ≈ 0, so T = rhρg/2. For accurate work, the small volume of water in the meniscus is allowed for by using (h + r/3) in place of h.

Procedure:

  1. Clean the capillary (with dilute acid, then distilled water) so that water wets it fully.

  2. Clamp it vertically in the beaker. Fix a pointer whose tip just touches the water surface.

  3. Focus the travelling microscope on the lowest point of the meniscus inside the tube. Note the vertical scale reading.

  4. Remove the beaker without disturbing the pointer. Focus on the pointer tip. Note the reading. The difference is h.

  5. Break the tube at the meniscus mark (or cut it there). Measure the internal diameter of the bore with the microscope in two perpendicular directions. Find r.

  6. Add a little detergent to the water and repeat. Note the smaller rise.

Observation table layout:

LiquidReading at meniscus (cm)Reading at pointer tip (cm)h (cm)Bore diameter, mean (mm)T (N/m)
Pure water
Water + detergent

Result: Surface tension of water at room temperature = … N/m. With detergent the rise falls, so the surface tension is lower.

Effect of detergents: Detergent molecules crowd at the surface and weaken the pull between water molecules there. T falls, so the water rises less. This lower T is also why soapy water wets oily cloth and lifts dirt.

Precautions:

  • The tube and water must be very clean. Grease lowers the rise.

  • Keep the tube vertical.

  • Read the bottom of the meniscus, not its edges.

  • Let the water rise and fall once by dipping the tube deeper, so the inner wall is fully wet.

Sources of error:

  • Bore not uniform or not circular.

  • Temperature change; T falls as water warms.

  • Measurement of r is the biggest error, as r is very small.

Viva-style points:

  • h × r = constant for a liquid (Jurin's law): a thinner tube shows a higher rise.

  • In a tube shorter than h, water does not overflow; the meniscus just becomes flatter.

  • Mercury shows a capillary fall, because its contact angle with glass is more than 90°.

Worked example 2.6: Water rises 6.0 cm in a clean capillary of bore radius 0.25 mm. Find T. (ρ = 1000 kg/m³, θ = 0)

Solution: T = rhρg/2 = (0.25 × 10⁻³ × 0.060 × 1000 × 10)/2 = 0.075 N/m.

Worked example 2.7: After adding detergent, the rise in the same tube becomes 2.8 cm. Find the new surface tension, taking θ = 0 and the same density.

Solution: T is proportional to h for the same tube. T' = 0.075 × 2.8/6.0 = 0.035 N/m. The detergent has more than halved T.

2.4 Experiment: Coefficient of viscosity by terminal velocity

Aim: To find the coefficient of viscosity of a given viscous liquid (glycerine or castor oil) by measuring the terminal velocity of a small steel ball.

Apparatus: Tall glass jar filled with the liquid, steel balls of different known sizes, screw gauge, stopwatch, metre scale, two rubber bands as marks, thermometer.

Principle and formula: A ball falling through a liquid speeds up until weight balances buoyancy plus Stokes' drag (6πηrv). It then falls at a steady terminal velocity v.

43πr3ρg=43πr3σg+6πηrv    ⇒    v=2r2(ρ−σ)g9η\frac{4}{3}\pi r^{3} \rho g = \frac{4}{3}\pi r^{3} \sigma g + 6\pi \eta r v \;\;\Rightarrow\;\; v = \frac{2 r^{2} (\rho - \sigma) g}{9 \eta}
η=2r2(ρ−σ)g9v\eta = \frac{2 r^{2} (\rho - \sigma) g}{9 v}

Here ρ is the density of the ball and σ that of the liquid. Since v ∝ r², a graph of v against r² is a straight line through the origin. Its slope gives η = 2(ρ − σ)g/(9 × slope).

Procedure:

  1. Fix two marks A and B on the jar, about 20 cm apart. Keep A well below the surface, so the ball reaches terminal speed before A.

  2. Measure the diameter of a ball with a screw gauge.

  3. Wet the ball with the same liquid. Drop it gently at the centre of the jar.

  4. Start the stopwatch as the ball crosses A and stop it at B. Find v = AB/t.

  5. Repeat with balls of other sizes. Note the liquid's temperature.

  6. Plot v against r² and find η from the slope.

Observation table layout:

S. No.Diameter (mm)r² (m²)Distance AB (m)Time t (s)v = AB/t (m/s)η (Pa s)
1
2
3

Result: Coefficient of viscosity of the liquid at … °C = … Pa s (or poise; 1 Pa s = 10 poise).

Precautions:

  • Drop the ball along the axis of the jar, away from the walls. Walls add extra drag.

  • The ball should be small and fully wet, with no air bubble stuck to it.

  • Keep the eye level with each mark when starting and stopping the watch.

  • Note the temperature; viscosity of a liquid falls quickly as it warms (think of honey in summer vs winter).

Sources of error:

  • The ball may not yet have reached terminal speed at the first mark.

  • Reaction time in starting and stopping the watch.

  • Wall effect when the jar is narrow.

Viva-style points:

  • Terminal velocity does not depend on the height from which the ball is dropped.

  • A ball denser than the liquid falls; one lighter than it rises (v becomes negative).

  • Stokes' law holds only for slow, streamline motion of a small sphere.

Worked example 2.8: A steel ball of diameter 2.0 mm (density 7800 kg/m³) falls through glycerine (density 1260 kg/m³). It covers 10.0 cm in 10.0 s at terminal speed. Find η.

Solution: r = 1.0 × 10⁻³ m, v = 0.010 m/s. η = 2 × (1.0 × 10⁻³)² × 6540 × 10/(9 × 0.010) = 1.45 Pa s.

Quick revision

  • Pendulum energy ∝ A². A² vs t is a falling exponential; ln A² vs t is a straight line.

  • Searle's: Y = MgL/(πr²ℓ). Reference wire cancels temperature and support sag.

  • From the ℓ vs M graph, Y = gL/(πr² × slope).

  • Capillary: T = rhρg/(2cosθ); hr is constant for a liquid.

  • Detergent lowers T, so capillary rise falls.

  • Terminal velocity: v = 2r²(ρ − σ)g/(9η); v ∝ r².

  • In Y, T and η, the radius carries the largest percentage error.

NEET traps

  • Thinking A (not A²) is proportional to energy. Halving amplitude leaves only a quarter of the energy.

  • Expecting A² to fall by equal amounts in equal times. It falls by equal fractions.

  • Counting the dead load in M. Only the added load stretches the wire for the reading.

  • Using diameter in place of radius in Y = MgL/(πr²ℓ) or in T = rhρg/2.

  • Forgetting buoyancy: the term is (ρ − σ), not ρ alone.

  • Starting the timer at the liquid surface, before the ball reaches terminal speed.

Practice MCQs: Chapter 2

Level 1: Concept check

1. The energy of a simple pendulum is proportional to (a) A (b) √A (c) A² (d) 1/A

2. For a pendulum losing energy to air drag, the graph of A² against time is (a) a falling curve that flattens with time (b) a rising straight line (c) a horizontal line (d) a rising parabola

3. In Searle's apparatus, the reference wire is used (a) to carry the main load (b) to increase the extension (c) to measure the diameter (d) to cancel the effects of temperature change and support sag

4. In Searle's method, the extension of the wire is read using (a) vernier callipers (b) a micrometer screw with a spirit level (c) a metre scale (d) a travelling microscope

5. For water in a clean glass capillary (contact angle zero), surface tension is given by (a) rhρg/2 (b) 2rhρg (c) hρg/2r (d) rhρg

6. When a detergent is added to the water in a capillary experiment, the rise (a) increases (b) stays the same (c) decreases (d) turns into a fall

7. The terminal velocity of a small sphere falling through a viscous liquid is proportional to (a) r (b) r² (c) 1/r (d) r³

8. In the terminal velocity experiment, the first timing mark is kept well below the liquid surface because (a) the liquid is denser at the bottom (b) buoyancy is smaller there (c) walls have no effect there (d) the ball must reach terminal speed before timing begins

9. The SI unit of coefficient of viscosity is (a) Pa s (b) N m (c) N/m (d) kg m/s

10. In the capillary rise experiment, the height of the column is measured with (a) a screw gauge (b) a travelling microscope (c) vernier callipers (d) a spherometer

Level 2: NEET standard

11. The amplitude of a damped pendulum falls from 8 cm to 4 cm. The percentage of the original energy still left is (a) 50% (b) 75% (c) 12.5% (d) 25%

12. For a damped pendulum, A² halves every 60 s. The starting amplitude is 12 cm. After 120 s the amplitude is (a) 6 cm (b) 3 cm (c) 8.5 cm (d) 4 cm

13. A wire 1.0 m long and 1.0 mm in diameter stretches 0.125 mm under a 2.0 kg load. Its Young's modulus is about (g = 10 m/s²) (a) 5.1 × 10¹⁰ N/m² (b) 8.1 × 10¹¹ N/m² (c) 2.0 × 10¹¹ N/m² (d) 1.0 × 10¹¹ N/m²

14. Wires A and B are of the same material and carry the same load. B is twice as long as A and has half its diameter. The ratio of extension of B to that of A is (a) 2 (b) 8 (c) 4 (d) 1/2

15. In Searle's experiment, the measurement that contributes the largest percentage error to Y is (a) length of the wire (b) the load (c) the value of g (d) diameter of the wire

16. Water rises 4.0 cm in a capillary of radius 0.30 mm. In a capillary of radius 0.20 mm of the same glass it rises (a) 6.0 cm (b) 2.7 cm (c) 9.0 cm (d) 4.0 cm

17. Water rises 7.0 cm in a clean capillary of radius 0.20 mm. Taking θ = 0, the surface tension is (a) 0.14 N/m (b) 0.035 N/m (c) 0.070 N/m (d) 0.70 N/m

18. If the radius of the falling ball is doubled, its terminal velocity in the same liquid becomes (a) 2 times (b) 4 times (c) 8 times (d) half

19. A steel ball (density 7800 kg/m³) of radius 1.5 mm falls through glycerine (density 1260 kg/m³, η = 1.5 Pa s). Its terminal velocity is about (a) 2.2 cm/s (b) 4.4 cm/s (c) 1.1 cm/s (d) 0.22 cm/s

20. In Searle's experiment, the extension vs load graph has slope 0.50 mm/kg. The wire is 2.0 m long and 0.25 mm in radius. Y is about (a) 1.0 × 10¹¹ N/m² (b) 4.1 × 10¹¹ N/m² (c) 5.1 × 10¹⁰ N/m² (d) 2.0 × 10¹¹ N/m²

21. A clean capillary tube is shorter than the height to which water would normally rise in it. Then (a) water flows out of the top like a fountain (b) water does not rise at all (c) water reaches the top and its meniscus becomes flatter (d) the meniscus turns convex

22. In Searle's experiment, readings taken while loading and while unloading are averaged mainly (a) to remove the zero error of the micrometer (b) to cancel the effect of elastic lag (c) to remove backlash (d) to find the breaking stress

Level 3: Challenge

23. For a damped pendulum, the graph of ln A² against t is a straight line of slope −0.010 s⁻¹. The time in which the energy falls to half is about (a) 100 s (b) 69 s (c) 35 s (d) 139 s

24. In a viscosity experiment, the ball's radius is 1.00 mm ± 0.01 mm and its terminal velocity is 2.00 cm/s ± 0.02 cm/s. Taking densities and g as exact, the maximum percentage error in η is (a) 1% (b) 2% (c) 4% (d) 3%

25. A ball of density 2000 kg/m³ has terminal velocity 2 cm/s in a liquid of density 1000 kg/m³. A ball of the same size but density 4000 kg/m³ in the same liquid has terminal velocity (a) 6 cm/s (b) 4 cm/s (c) 8 cm/s (d) 3 cm/s

26. Water (T = 0.072 N/m) rises 5.0 cm in a capillary. With detergent added, the rise in the same tube is 3.0 cm, with the same density and contact angle. The new surface tension is about (a) 0.12 N/m (b) 0.072 N/m (c) 0.043 N/m (d) 0.030 N/m

27. A wire stretches 0.90 mm under a 3 kg load. A wire of the same material, twice as long and twice the diameter, carries the same load. Its extension is (a) 0.90 mm (b) 1.80 mm (c) 0.225 mm (d) 0.45 mm

28. A damped pendulum shows amplitudes of 10 cm, 8 cm and 6.4 cm at equal time intervals. The next reading should be close to (a) 4.8 cm (b) 5.12 cm (c) 4.4 cm (d) 5.6 cm

29. Assertion (A): The energy of a damped pendulum falls by equal amounts in equal intervals of time. Reason (R): The energy of an oscillator is proportional to the square of its amplitude. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: The viscosity of glycerine decreases as its temperature rises. Statement II: In Searle's experiment the wire should be loaded beyond its elastic limit to get a large extension. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1cE = ½ mω²A²
2aExponential decay of A²
3dBoth wires feel the same temperature and support movement
4bBubble is relevelled with the micrometer
5aT = rhρg/(2cosθ), cosθ = 1
6cDetergent lowers T, and h ∝ T
7bv = 2r²(ρ − σ)g/9η
8dBall accelerates at first
9aη = F/(A dv/dx) gives Pa s
10bMicroscope reads meniscus and pointer tip
11d(4/8)² = 1/4
12aTwo halvings: 144 → 36 cm², A = 6 cm
13c20 × 1.0/(π × (0.5 × 10⁻³)² × 1.25 × 10⁻⁴) = 2.0 × 10¹¹
14bℓ ∝ L/d²: 2 × 4 = 8
15dSmall and squared
16ahr constant: 4.0 × 0.30/0.20 = 6.0 cm
17c0.2 × 10⁻³ × 0.07 × 10⁴/2 = 0.070 N/m
18bv ∝ r²
19a2 × 2.25 × 10⁻⁶ × 6540 × 10/(9 × 1.5) = 0.0218 m/s
20d10 × 2.0/(π × 6.25 × 10⁻⁸ × 5 × 10⁻⁴) = 2.0 × 10¹¹
21cMeniscus radius grows so the column stays in balance
22bWire lags in recovering; average cancels it
23bt = ln 2/0.010 = 69 s
24d2 × 1% + 1% = 3%
25av ∝ (ρ − σ): 3000/1000 × 2 = 6 cm/s
26cT ∝ h: 0.072 × 3/5 = 0.043 N/m
27dℓ ∝ L/d²: 0.90 × 2/4 = 0.45 mm
28bEach step multiplies A by 0.8: 6.4 × 0.8 = 5.12 cm
29dEnergy falls by equal fractions, not equal amounts
30cLoading past the elastic limit ruins the wire and the formula

Chapter 2 revision sheet

One-page summary

  • A pendulum's energy E = ½ mω²A², so E ∝ A². Plotting A² against t shows directly how energy is lost.

  • With air drag, A² falls exponentially with time. ln A² vs t is a straight line with a negative slope.

  • If the amplitude halves, the energy falls to one quarter.

  • Young's modulus by Searle's method: Y = MgL/(πr²ℓ), where ℓ is the extension for load Mg.

  • The ℓ vs M graph is a straight line through the origin (within the elastic limit); Y = gL/(πr² × slope).

  • The reference wire cancels changes due to temperature and sag of the support.

  • Readings taken while loading and unloading should agree; this checks that the wire stayed elastic.

  • Capillary rise: h = 2T cos θ/(rρg). For clean glass and water, θ ≈ 0, so h r = constant.

  • Detergent lowers surface tension, so the water rises less. Hotter water also rises less.

  • Mercury in glass shows capillary depression (θ greater than 90°).

  • Stokes' law: viscous force F = 6πηrv. At terminal velocity, weight = upthrust + viscous force.

  • Terminal velocity v = 2r²(ρ − σ)g/(9η), so v ∝ r².

  • Liquid viscosity falls as temperature rises, so balls fall faster in warm glycerine.

  • Start timing only after the ball has fallen some distance, so it has reached terminal velocity.

Must-remember table

ExperimentKey formulaGraphUnit of result
Damped pendulumE ∝ A²A² vs t: decaying curve; ln A² vs t: straight lineJ (relative)
Young's modulusY = MgL/(πr²ℓ)ℓ vs M: straight line through originN/m² (Pa)
Surface tensionT = rhρg/(2 cos θ)h vs 1/r: straight lineN/m
Viscosityη = 2r²(ρ − σ)g/(9v)v vs r²: straight linePa s (N s/m²)
Typical valuesY(steel) ≈ 2 × 10¹¹ Pa; T(water) ≈ 0.072 N/m; η(glycerine) ≈ 1 Pa s

Memory aids

  • "Half the swing, quarter the energy": A → A/2 means E → E/4, because E ∝ A².

  • "MgL over pi-r-squared-l": read Y = MgL/(πr²ℓ) as "Mass, g, Length on top; pi, r², little l below".

  • "Thin tube, Tall column": smaller r gives larger h, since h r = constant.

  • "Two-Nine Stokes": v = 2r²(ρ − σ)g/(9η). The 2 and 9 sit on top and bottom.

  • "Soap Sinks, Heat Hurries": soap (detergent) sinks the capillary column; heat makes the ball hurry through the liquid.

Concept connections

  • Young's modulus, surface tension and Stokes' law are developed in Physics Book 7: Properties of Solids and Liquids.

  • Damped oscillations and energy of SHM come from Physics Book 10: Oscillations and Waves.

  • Measuring r with a screw gauge links back to Chapter 1 and to Physics Book 1: Physics and Measurement for error analysis.

Practice MCQs: Chapter 2, Level 4 (new NEET pattern)

31. Match List I (experiment) with List II (formula used).

  • List I: (A) Young's modulus; (B) Surface tension by capillary rise; (C) Viscosity by terminal velocity; (D) Damped pendulum

  • List II: (i) η = 2r²(ρ − σ)g/(9v); (ii) Y = MgL/(πr²ℓ); (iii) E ∝ A²; (iv) T = rhρg/(2 cos θ)

(a) A-iv, B-ii, C-iii, D-i (b) A-ii, B-i, C-iv, D-iii (c) A-ii, B-iv, C-i, D-iii (d) A-iii, B-iv, C-i, D-ii

32. Match List I (graph) with List II (shape).

  • List I: (A) Extension ℓ vs load M for Searle's wire; (B) A² vs t for a damped pendulum; (C) Capillary rise h vs tube radius r; (D) ln A² vs t for a damped pendulum

  • List II: (i) Rectangular hyperbola; (ii) Straight line through the origin; (iii) Decaying exponential curve; (iv) Straight line with negative slope

(a) A-ii, B-iii, C-i, D-iv (b) A-iii, B-ii, C-iv, D-i (c) A-ii, B-iv, C-i, D-iii (d) A-i, B-iii, C-ii, D-iv

33. Match List I (change) with List II (effect).

  • List I: (A) Detergent added to water in a capillary experiment; (B) Glycerine warmed in the viscosity experiment; (C) Thicker wire, same load and length; (D) Longer wire, same load and radius

  • List II: (i) Extension rises; (ii) Height of rise falls; (iii) Terminal velocity rises; (iv) Extension falls

(a) A-iii, B-ii, C-i, D-iv (b) A-ii, B-i, C-iv, D-iii (c) A-iv, B-iii, C-ii, D-i (d) A-ii, B-iii, C-iv, D-i

34. Match List I (precaution) with List II (reason).

  • List I: (A) A reference wire in Searle's apparatus; (B) Start timing well below the liquid surface; (C) Clean the capillary tube thoroughly; (D) Take readings while loading and unloading

  • List II: (i) The ball reaches terminal velocity first; (ii) Cancels temperature change and support sag; (iii) Checks that the wire stays within the elastic limit; (iv) Good wetting, so the contact angle is near zero

(a) A-i, B-ii, C-iii, D-iv (b) A-ii, B-i, C-iv, D-iii (c) A-ii, B-iv, C-i, D-iii (d) A-iii, B-i, C-iv, D-ii

35. How many of the following statements are correct?

  • A. A pendulum's energy is proportional to the square of its amplitude.

  • B. If the amplitude falls to half, the energy also falls to half.

  • C. Terminal velocity of a sphere in a liquid is proportional to r².

  • D. Adding detergent to water increases its surface tension.

(a) Two (b) Three (c) One (d) Four

36. Choose the correct set of statements about Searle's experiment.

  • A. Young's modulus of a wire depends on the length of wire used.

  • B. For a fixed load, extension is proportional to L/r².

  • C. Y = gL/(πr² × slope), where slope is that of the ℓ vs M graph.

  • D. The wire should be loaded beyond its elastic limit for an accurate result.

(a) A and B only (b) C and D only (c) B and C only (d) A, B and C only

37. How many of these statements about the viscosity experiment are correct?

  • A. Viscosity of a liquid decreases as its temperature rises.

  • B. At terminal velocity, the net force on the ball is zero.

  • C. Upthrust on the ball is ignored in Stokes' method.

  • D. In a narrow jar, the walls make the measured velocity lower than ideal.

(a) One (b) Two (c) Four (d) Three

38. Choose the correct set of statements about capillary rise.

  • A. For a given liquid at a fixed temperature, h × r is constant.

  • B. If the tube is shorter than h, water overflows from the top like a fountain.

  • C. Mercury shows a fall, not a rise, in a glass capillary.

  • D. Water rises higher when it is warmer.

(a) A and C only (b) A, B and C only (c) B and D only (d) C and D only

39. Searle's experiment on a wire with L = 2.0 m and r = 0.50 mm gives this table (g = 10 m/s²):

Load M (kg)1234
Extension ℓ (mm)0.1250.2500.3750.500

Young's modulus of the wire is about (a) 1.02 × 10¹¹ N/m² (b) 2.04 × 10¹¹ N/m² (c) 4.08 × 10¹¹ N/m² (d) 5.1 × 10¹⁰ N/m²

40. An A² vs t graph for a pendulum starts at 64 cm² at t = 0 and falls to 16 cm² at t = 30 s, decaying exponentially. The amplitude becomes 2 cm at (a) 45 s (b) 90 s (c) 60 s (d) 120 s

41. Water rises 7.2 cm in a clean glass tube of radius 0.20 mm (θ = 0, ρ = 1000 kg/m³, g = 10 m/s²). The surface tension, and the rise in a tube of radius 0.30 mm, are (a) 0.036 N/m, 4.8 cm (b) 0.072 N/m, 10.8 cm (c) 0.144 N/m, 4.8 cm (d) 0.072 N/m, 4.8 cm

Passage for Q42–43: A steel ball of radius 1.0 mm (density 7800 kg/m³) is dropped into a tall jar of glycerine (density 1260 kg/m³). After the first few centimetres, it covers each 10 cm mark interval in the same time, moving at 1.6 cm/s. Take g = 10 m/s².

42. The coefficient of viscosity of the glycerine is about (a) 0.45 Pa s (b) 0.91 Pa s (c) 1.82 Pa s (d) 9.1 Pa s

43. A ball of the same steel with radius 2.0 mm would have a terminal velocity of (a) 3.2 cm/s (b) 1.6 cm/s (c) 6.4 cm/s (d) 12.8 cm/s

44. Two wires of the same material have lengths L and 2L and radii r and 2r. The same load hangs on each. The ratio of their extensions (first : second) is (a) 1 : 2 (b) 1 : 4 (c) 4 : 1 (d) 2 : 1

45. Water rises to a height of 6 cm in a long capillary held vertical. The tube is now tilted so that it makes 60° with the vertical. The length of water column in the tube is (a) 12 cm (b) 6 cm (c) 3 cm (d) 10.4 cm

Level 4 answer key

QAnsReason
31cEach experiment paired with its working formula
32aℓ ∝ M; A² decays; h ∝ 1/r is a hyperbola; ln A² falls linearly
33dDetergent lowers T; warm glycerine lower η; ℓ ∝ L/r²
34bEach precaution matched to the error it prevents
35aA and C true; energy goes to one quarter; detergent lowers T
36cY is a material property; never exceed the elastic limit
37dA, B, D true; upthrust is included in Stokes' method
38aShort tube: meniscus flattens, no overflow; warm water rises less
39bSlope 0.125 mm/kg; Y = gL/(πr² × slope) = 20/(π × 0.25 × 10⁻⁶ × 1.25 × 10⁻⁴) ≈ 2.04 × 10¹¹
40cA² falls by 4 every 30 s; 64 → 16 → 4 cm² takes 60 s
41dT = h r ρ g/2 = 0.072 N/m; h r constant gives 7.2 × 0.2/0.3 = 4.8 cm
42bη = 2(10⁻³)²(6540)(10)/(9 × 0.016) ≈ 0.91 Pa s
43cv ∝ r²: doubling r gives 4 × 1.6 = 6.4 cm/s
44dℓ ∝ L/r²: (L/r²) : (2L/4r²) = 2 : 1
45aVertical height stays 6 cm; length = 6/cos 60° = 12 cm
30 min left
‹
›