Chapter 4: Electricity
What you will learn
How a metre bridge uses the Wheatstone bridge balance to find an unknown resistance, and then resistivity.
Why the balance point should be near the middle, and why R and X are interchanged.
How to verify Ohm's law and read resistance from the slope of a V–I graph.
How the half deflection method gives the resistance of a galvanometer, and what figure of merit means.
Which circuit mistakes NEET likes to test.
4.1 Experiment: Resistivity of a wire using a metre bridge
Aim: To find the resistance of a given wire using a metre bridge, and hence the resistivity of its material.
Apparatus: Metre bridge (a 1 m long uniform manganin or constantan wire on a board, with thick copper strips forming two gaps), resistance box, the wire under test, galvanometer, jockey, Leclanché cell or battery eliminator, one-way key, screw gauge, metre scale, connecting wires.
Principle and formula: The metre bridge is a Wheatstone bridge. The two parts of the bridge wire on either side of the jockey form two arms. At balance, no current flows through the galvanometer.
Put the resistance box R in the left gap and the unknown X in the right gap. If the balance point is l cm from the left end:
The bridge wire is uniform, so resistance of each part is proportional to its length. Once X is known, measure the length L and diameter d of the test wire:

R sits in the left gap and X in the right; when the jockey at J gives no deflection, the two parts of the wire, l and 100 − l, are in the same ratio as R and X.
Procedure:
Connect the circuit as in Figure 4.1. Clean the ends of all wires with sandpaper. Tighten every terminal.
Take out a suitable plug from the resistance box (say 2 Ω). Close the key.
Touch the jockey near the left end, then near the right end. The galvanometer should deflect in opposite directions. If it does not, recheck the connections.
Move the jockey by touching (not sliding) till the galvanometer shows zero. Note l.
Repeat for three or four values of R, chosen so l falls between about 30 cm and 70 cm.
Interchange R and X and repeat. Take the mean X.
Measure L of the test wire with a metre scale, and d with a screw gauge at several places.
Observation table layout:
| S. No. | R (Ω) | Balance length l (cm) | 100 − l (cm) | X = R(100 − l)/l (Ω) |
|---|---|---|---|---|
| 1 | ||||
| 2 | ||||
| 3 |
Result: Resistance of the wire = … Ω. Resistivity of its material = … Ω m.
Precautions:
Keep the key closed only while taking a reading. Current heats the wires and changes resistance.
Touch the jockey gently; sliding it scrapes the bridge wire and makes it non-uniform.
Choose R so that the balance point is near the middle of the wire. The bridge is most sensitive there.
Use thick copper strips and short leads, so their resistance is negligible.
Sources of error:
End resistance: the bridge wire's ends and the copper strip joints add small unknown resistances. Interchanging R and X reduces this.
The bridge wire may not be perfectly uniform.
Error in measuring d, which appears squared in ρ.
Viva-style points:
At balance, the galvanometer reading is zero, so its own resistance does not matter. The cell's emf and internal resistance do not matter either.
Bridge wire is made of manganin or constantan: high resistivity and very low temperature coefficient.
Interchanging the cell and galvanometer does not change the balance point.
A bridge balances best when all four arms are of the same order of resistance.
Worked example 4.1: With R = 4 Ω in the left gap, the balance point is at 40.0 cm. Find X.
Solution: X = 4 × (100 − 40.0)/40.0 = 4 × 60/40 = 6.0 Ω.
Worked example 4.2: The 6.0 Ω wire of example 4.1 is 1.00 m long with diameter 0.50 mm. Find its resistivity.
Solution: πr² = π × (0.25 × 10⁻³)² = 1.96 × 10⁻⁷ m². ρ = 6.0 × 1.96 × 10⁻⁷/1.00 = 1.18 × 10⁻⁶ Ω m. This is close to nichrome.
Worked example 4.3: With R = 5 Ω in the left gap, balance is at 40.0 cm. With R and X interchanged, balance is at 60.4 cm from the left end. Find X.
Solution: First: X = 5 × 60.0/40.0 = 7.50 Ω. After interchange X is on the left, so X/5 = 60.4/39.6, giving X = 7.63 Ω. Mean X = 7.56 Ω. The two values differ because of end resistance; the mean reduces that error.
4.2 Experiment: Resistance of a wire using Ohm's law
Aim: To find the resistance of a given wire by plotting a graph of potential difference against current.
Apparatus: The wire (resistance coil), battery or eliminator, ammeter, voltmeter, rheostat, one-way key, connecting wires, sandpaper.
Principle and formula: At constant temperature, the current through a metallic conductor is proportional to the potential difference across it (Ohm's law).
The circuit: battery, key, rheostat, ammeter and wire in series. The voltmeter is connected in parallel across the wire only.
Procedure:
Note the range and least count of the ammeter and voltmeter. Check their zero errors.
Connect the circuit. The positive terminals of both meters go toward the positive terminal of the battery.
Close the key. Set the rheostat for a small current. Note I and V.
Change the rheostat in steps to get 5 or 6 sets of readings.
Open the key between readings, so the wire does not heat up.
Plot V (y-axis) against I (x-axis). Draw the best straight line and find its slope.
Observation table layout:
| S. No. | Ammeter reading I (A) | Voltmeter reading V (V) | R = V/I (Ω) |
|---|---|---|---|
| 1 | |||
| 2 | |||
| 3 |
Graph: V vs I is a straight line through the origin. Its slope is R. (If I is on the y-axis, the slope is 1/R.)
Result: Resistance of the wire = … Ω, from the slope.
Precautions:
Ammeter in series, voltmeter in parallel, polarity correct.
Keep the current small. A hot wire has a higher resistance and the graph bends.
Choose meter ranges so the readings use a large part of the scale.
Sources of error:
Heating of the wire during the experiment.
The voltmeter draws a little current, so the ammeter reads slightly more than the current in the wire.
Loose connections add contact resistance.
Viva-style points:
An ideal ammeter has zero resistance; an ideal voltmeter has infinite resistance.
The rheostat only changes the current; it is not part of the resistance being measured.
A filament bulb does not give a straight V–I line, because its temperature changes a lot.
Worked example 4.4: Readings for a coil are (0.2 A, 1.0 V), (0.4 A, 2.0 V), (0.6 A, 3.1 V), (0.8 A, 4.0 V). Find R from the graph.
Solution: The best line passes through (0.2 A, 1.0 V) and (0.8 A, 4.0 V). Slope = (4.0 − 1.0)/(0.8 − 0.2) = 3.0/0.6 = 5.0 Ω. The point (0.6 A, 3.1 V) is a slight scatter.
Worked example 4.5: A 10.0 Ω wire is measured with a voltmeter of resistance 990 Ω placed across it and the ammeter before both. What value of V/I does the student get?
Solution: The ammeter reads the current through the wire and voltmeter together. V/I = parallel combination = 10 × 990/(10 + 990) = 9.9 Ω. The measured value is slightly low.
4.3 Experiment: Resistance and figure of merit of a galvanometer by half deflection
Aim: To find the resistance G of a galvanometer by the half deflection method, and its figure of merit k.
Apparatus: Weston-type moving coil galvanometer, battery (about 2 V), a high resistance box R (0 to 10 kΩ), a low resistance box S (0 to 200 Ω), two one-way keys, voltmeter, connecting wires.
Principle and formula: The battery, R, the galvanometer and key K₁ are in series. The shunt S, with key K₂, is connected directly across the galvanometer.
With K₁ closed and K₂ open, the current through G gives deflection θ:
Now close K₂ and adjust S until the deflection drops to θ/2, with R unchanged. The galvanometer current is now half of the earlier value.
Simplifying: 2S(R + G) = R(G + S) + GS, so SR + SG = RG.
The figure of merit is the current needed for one division of deflection:
Procedure:
Connect the circuit. Take out a high resistance (say 5000 Ω) from R with K₂ open.
Close K₁. Adjust R to get a large, even-numbered deflection θ (say 30 divisions).
Close K₂. Without changing R, adjust S until the deflection is exactly θ/2.
Note R, θ and S. Calculate G.
Repeat for three other values of θ.
Measure E with a voltmeter, and find k for each set.
Observation table layout:
| S. No. | R (Ω) | θ (div) | S (Ω) at θ/2 | G = RS/(R − S) (Ω) | k = E/((R + G)θ) (A/div) |
|---|---|---|---|---|---|
| 1 | |||||
| 2 | |||||
| 3 |
Result: Resistance of the galvanometer = … Ω. Figure of merit = … A/div.
Precautions:
Always start with a high R, so that a large current does not damage the galvanometer.
Keep R unchanged when you adjust S.
Choose θ as an even number of divisions, so θ/2 is a whole number.
The battery emf must stay steady; use a fresh cell or an eliminator.
Sources of error:
Plugs in the resistance boxes may be loose, adding contact resistance.
Battery emf may drift during the experiment.
Reading the pointer at an angle (parallax).
Viva-style points:
Figure of merit is the reciprocal of current sensitivity. A smaller k means a more sensitive galvanometer.
The approximation G ≈ S is good only when R is very much larger than S.
The same galvanometer is later converted to an ammeter (with a low shunt) or a voltmeter (with a high series resistance).
Worked example 4.6: With R = 5000 Ω the galvanometer deflects 30 divisions. Adding a shunt S = 50 Ω brings it to 15 divisions. Find G.
Solution: G = RS/(R − S) = 5000 × 50/4950 = 50.5 Ω. The approximation G ≈ S = 50 Ω is only 1% off.
Worked example 4.7: For the data of example 4.6, the battery emf is 2.0 V. Find the figure of merit.
Solution: I_g = 2.0/(5000 + 50.5) = 3.96 × 10⁻⁴ A. k = 3.96 × 10⁻⁴/30 = 1.32 × 10⁻⁵ A/div.
Quick revision
Metre bridge: X = R(100 − l)/l, with R in the left gap. ρ = Xπd²/(4L).
Balance near the middle for best sensitivity; interchange R and X to cut end resistance error.
At balance, galvanometer resistance and cell emf do not matter.
Ohm's law: slope of V–I graph = R; voltmeter in parallel, ammeter in series.
Half deflection: G = RS/(R − S) ≈ S when R is much larger than S.
Figure of merit k = E/((R + G)θ), in A/div; smaller k means more sensitive.
NEET traps
Writing X = Rl/(100 − l) when R is in the left gap. Check which gap holds which resistor.
Sliding the jockey along the wire. It must only be tapped.
Using the slope of an I–V graph (I on y-axis) as R instead of 1/R.
Changing R while adjusting S in the half deflection method.
Forgetting that at metre bridge balance, the galvanometer's own resistance plays no part.
Taking k as deflection per unit current. That is current sensitivity; k is its reciprocal.
Practice MCQs: Chapter 4
Level 1: Concept check
1. A metre bridge works on the principle of (a) a potentiometer (b) Ohm's law alone (c) Joule heating (d) a Wheatstone bridge
2. The bridge wire of a metre bridge is usually made of (a) copper (b) manganin or constantan (c) iron (d) tungsten
3. In a metre bridge experiment, the jockey should be (a) tapped gently on the wire (b) slid along the wire under pressure (c) kept pressed all the time (d) connected to the cell
4. In the Ohm's law experiment, the voltmeter is connected (a) in series with the wire (b) in series with the rheostat (c) in parallel with the wire only (d) across the battery only
5. The slope of a V–I graph (V on y-axis) for a metallic wire gives (a) conductance (b) resistance (c) resistivity (d) power
6. In the half deflection method, the shunt S is connected (a) in series with the battery (b) in series with the galvanometer (c) across the high resistance R (d) across the galvanometer
7. Figure of merit of a galvanometer is the (a) current per division of deflection (b) deflection per unit current (c) voltage per division (d) resistance per division
8. The bridge is most sensitive when the balance point is (a) near the left end (b) near the right end (c) near the middle of the wire (d) beyond the wire
9. In the half deflection method, R is kept very much larger than S so that (a) the galvanometer does not deflect (b) G ≈ S becomes a good approximation (c) the battery does not run down (d) the shunt current is zero
10. To reduce the effect of end resistance in a metre bridge, we (a) interchange R and X and take the mean (b) use a thicker galvanometer wire (c) increase the cell emf (d) slide the jockey faster
Level 2: NEET standard
11. With R = 3 Ω in the left gap of a metre bridge, the balance point is at 60.0 cm. The unknown resistance in the right gap is (a) 4.5 Ω (b) 1.8 Ω (c) 2.0 Ω (d) 5.0 Ω
12. A wire of resistance 4.0 Ω is 0.80 m long and 0.40 mm in diameter. Its resistivity is about (a) 2.51 × 10⁻⁶ Ω m (b) 1.57 × 10⁻⁷ Ω m (c) 3.14 × 10⁻⁶ Ω m (d) 6.28 × 10⁻⁷ Ω m
13. A metre bridge balances at 50.0 cm with 10 Ω in the left gap and wire X in the right gap. X is replaced by a wire of the same material and thickness but twice as long. The new balance point is (a) 66.7 cm (b) 33.3 cm (c) 25.0 cm (d) 50.0 cm
14. Which of these does NOT change the balance point of a metre bridge? (a) The resistance of the galvanometer (b) The value of R (c) The value of X (d) Non-uniformity of the bridge wire
15. The balance point of a metre bridge comes at 4 cm from the left end. The student should (a) accept the reading (b) increase the cell emf (c) change R so that the balance moves toward the middle (d) reverse the galvanometer
16. In an Ohm's law experiment, V = 1.5 V at I = 0.10 A and V = 6.0 V at I = 0.40 A on the best line. The resistance is (a) 0.067 Ω (b) 7.5 Ω (c) 60 Ω (d) 15 Ω
17. A student plots I on the y-axis against V on the x-axis and gets a slope of 0.25 A/V. The resistance is (a) 4 Ω (b) 0.25 Ω (c) 2 Ω (d) 16 Ω
18. A 20 Ω wire is tested with a 380 Ω voltmeter across it and the ammeter in the main line. The value of V/I obtained is (a) 20 Ω (b) 19 Ω (c) 21 Ω (d) 400 Ω
19. With R = 6000 Ω, a galvanometer shows a deflection θ. Shunting it with S = 60 Ω halves the deflection. The galvanometer resistance is (a) 59.4 Ω (b) 60.0 Ω (c) 60.6 Ω (d) 6060 Ω
20. A galvanometer (G = 50 Ω) in series with 4950 Ω and a 1.5 V cell shows 30 divisions. Its figure of merit is (a) 3 × 10⁻⁴ A/div (b) 1 × 10⁻⁴ A/div (c) 9 × 10⁻³ A/div (d) 1 × 10⁻⁵ A/div
21. In the half deflection method, while S is being adjusted, R must (a) be reduced to zero (b) stay unchanged (c) be made equal to S (d) be doubled
22. A galvanometer has a current sensitivity of 2 × 10⁵ div/A. Its figure of merit is (a) 5 × 10⁻⁶ A/div (b) 2 × 10⁵ A/div (c) 5 × 10⁻⁵ A/div (d) 2 × 10⁻⁶ A/div
Level 3: Challenge
23. With R = 10 Ω in the left gap and X in the right, balance is at 41.0 cm. With R and X interchanged, balance is at 59.8 cm. The best value of X is about (a) 14.4 Ω (b) 14.9 Ω (c) 14.6 Ω (d) 6.9 Ω
24. Wire A (1.0 m, diameter 0.50 mm) is in the left gap and wire B (0.50 m, diameter 0.25 mm) of the same material is in the right gap of a metre bridge. The balance point is at (a) 50.0 cm (b) 66.7 cm (c) 25.0 cm (d) 33.3 cm
25. In a half deflection experiment, R = 500 Ω and S = 50 Ω at half deflection. The true galvanometer resistance is (a) 50.0 Ω (b) 55.6 Ω (c) 45.5 Ω (d) 500 Ω
26. A metre bridge balances at 60.0 cm with 12 Ω in the left gap and X in the right gap. A 24 Ω resistor is then joined in parallel with X. With the same 12 Ω, the new balance point is (a) 66.7 cm (b) 40.0 cm (c) 33.3 cm (d) 75.0 cm
27. In an Ohm's law experiment, a large current is passed for a long time through the wire. The V–I graph (V on y-axis) (a) stays a straight line (b) bends toward the I-axis (c) bends toward the V-axis, as slope increases (d) passes below the origin
28. A galvanometer of resistance 50 Ω, in series with 2950 Ω and a 3.0 V cell, shows 40 divisions. Its figure of merit is (a) 2.5 × 10⁻⁴ A/div (b) 2.5 × 10⁻⁵ A/div (c) 4 × 10⁴ A/div (d) 1 × 10⁻³ A/div
29. Assertion (A): The jockey should not be slid along the metre bridge wire. Reason (R): At balance, no current flows through the galvanometer. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true
30. Statement I: The figure of merit of a galvanometer is the reciprocal of its current sensitivity. Statement II: In the half deflection method, G = RS/(R − S). (a) Both true (b) Both false (c) I true, II false (d) I false, II true
Answer key with reasons
| Q | Ans | Reason |
|---|---|---|
| 1 | d | Balanced four-arm bridge |
| 2 | b | High resistivity, tiny temperature coefficient |
| 3 | a | Sliding scrapes the wire |
| 4 | c | Voltmeter measures p.d. across the wire |
| 5 | b | V/I = R |
| 6 | d | Shunt diverts part of the current around G |
| 7 | a | k = I/θ |
| 8 | c | Equal arms give the highest sensitivity |
| 9 | b | Main current barely changes when S is added |
| 10 | a | End errors act in opposite directions |
| 11 | c | X = 3 × 40/60 = 2.0 Ω |
| 12 | d | 4.0 × π × (0.2 × 10⁻³)²/0.80 = 6.28 × 10⁻⁷ Ω m |
| 13 | b | X = 20 Ω; 10/20 = l/(100 − l), l = 33.3 cm |
| 14 | a | No current through G at balance |
| 15 | c | End errors are large near the ends |
| 16 | d | 4.5/0.30 = 15 Ω |
| 17 | a | R = 1/slope = 4 Ω |
| 18 | b | 20 × 380/400 = 19 Ω |
| 19 | c | 6000 × 60/5940 = 60.6 Ω |
| 20 | d | I = 1.5/5000 = 3 × 10⁻⁴ A; /30 = 1 × 10⁻⁵ A/div |
| 21 | b | G = RS/(R − S) assumes the same R |
| 22 | a | k = 1/(2 × 10⁵) = 5 × 10⁻⁶ A/div |
| 23 | c | 14.39 and 14.88 Ω, mean 14.6 Ω |
| 24 | d | R ∝ L/d²: A is 4 units, B is 8 units; l = 100/3 cm |
| 25 | b | 500 × 50/450 = 55.6 Ω |
| 26 | a | X = 8 Ω; 8 parallel 24 = 6 Ω; l = 12/18 × 100 = 66.7 cm |
| 27 | c | Hot wire, higher R, larger slope |
| 28 | b | I = 3/3000 = 1 mA; /40 = 2.5 × 10⁻⁵ A/div |
| 29 | b | Both true, but A is about wire damage, not null current |
| 30 | a | Both are standard results |
Chapter 4 revision sheet
One-page summary
The metre bridge is a Wheatstone bridge with a 100 cm uniform wire as two of its arms.
At balance (zero galvanometer current): X/R = l/(100 − l), with l measured from the X end.
At balance the galvanometer carries no current, so its resistance and the cell's emf do not affect the result.
Interchanging X and R moves the balance point to (100 − l). Averaging both cancels end errors.
Choose R so the balance point lies near the middle (40–60 cm); the bridge is most sensitive there.
Resistivity: ρ = πr²X/L, with r from a screw gauge (Chapter 1) and L the length of the test wire.
Ohm's law: ammeter in series, voltmeter in parallel. The V–I graph of an ohmic wire is a straight line through the origin; slope = R.
The slope of an I–V graph is 1/R (conductance). Heating raises a metal's resistance, so keep current small and close the key only while reading.
Half-deflection: with a high resistance R, deflection θ; a shunt S across the galvanometer brings it to θ/2. Then G = RS/(R − S).
When R is much larger than S, G ≈ S.
Figure of merit k = current per division = E/((R + G)θ). A smaller k means a more sensitive galvanometer.
Full-scale current I_g = k × total divisions. This links to converting a galvanometer into an ammeter or voltmeter.
Must-remember table
| Quantity | Formula | Unit |
|---|---|---|
| Metre bridge balance | X = R l/(100 − l) | Ω |
| Resistivity | ρ = πr²X/L | Ω m |
| Resistance from V–I graph | R = slope = ΔV/ΔI | Ω |
| Galvanometer resistance | G = RS/(R − S) | Ω |
| Figure of merit | k = E/((R + G)θ) | A/division |
| Voltmeter series resistance | R_s = V/I_g − G | Ω |
| Ammeter shunt | S = I_g G/(I − I_g) | Ω |
Memory aids
"L over the Leftover": X/R = l/(100 − l): the length on X's side over the leftover length.
"Middle is Mighty": the balance point is most sensitive near the middle of the wire.
"RS over R minus S": G = RS/(R − S); read it as "product over difference".
"Series Sees current, Parallel Probes voltage": ammeter in series, voltmeter in parallel.
"Merit is Meagre for the sensitive": smaller figure of merit, more sensitive galvanometer.
Concept connections
Wheatstone bridge, resistivity and Ohm's law are taught in Physics Book 12: Current Electricity.
Galvanometer conversion to ammeter and voltmeter uses Physics Book 13: Magnetic Effects of Current and Magnetism.
Measuring wire diameter for resistivity uses the screw gauge from Chapter 1 of this book.
Practice MCQs: Chapter 4, Level 4 (new NEET pattern)
31. Match List I (experiment step) with List II (formula).
List I: (A) Metre bridge balance; (B) Resistivity of the wire; (C) Galvanometer resistance by half deflection; (D) Figure of merit
List II: (i) ρ = πr²X/L; (ii) k = E/((R + G)θ); (iii) X/R = l/(100 − l); (iv) G = RS/(R − S)
(a) A-iii, B-i, C-iv, D-ii (b) A-i, B-iii, C-ii, D-iv (c) A-iii, B-iv, C-i, D-ii (d) A-iv, B-i, C-iii, D-ii
32. Match List I (part) with List II (role).
List I: (A) Jockey; (B) Thick copper strips of the metre bridge; (C) Rheostat in the Ohm's law circuit; (D) Shunt S in the half-deflection method
List II: (i) Brings the deflection down to half; (ii) Finds the null point by a light touch; (iii) Varies the current in the circuit; (iv) Joins the gaps with negligible resistance
(a) A-iv, B-ii, C-i, D-iii (b) A-ii, B-iii, C-iv, D-i (c) A-ii, B-iv, C-iii, D-i (d) A-iii, B-iv, C-ii, D-i
33. Match List I (graph feature) with List II (meaning).
List I: (A) V–I graph is a straight line through the origin; (B) Slope of the V–I graph; (C) Slope of the I–V graph; (D) V–I graph of a filament bends upward at high current
List II: (i) Conductance; (ii) Resistance rises on heating; (iii) Ohmic conductor; (iv) Resistance
(a) A-iv, B-iii, C-ii, D-i (b) A-iii, B-iv, C-i, D-ii (c) A-iii, B-i, C-iv, D-ii (d) A-i, B-iv, C-iii, D-ii
34. Match List I (problem) with List II (remedy).
List I: (A) End errors of the metre bridge; (B) Balance point very close to one end; (C) Heating of the wire; (D) Test wire not uniform
List II: (i) Choose R so balance lies near the middle; (ii) Interchange X and R and average; (iii) Measure diameter at several points; (iv) Close the key only while taking a reading
(a) A-i, B-ii, C-iii, D-iv (b) A-ii, B-iv, C-i, D-iii (c) A-iv, B-i, C-ii, D-iii (d) A-ii, B-i, C-iv, D-iii
35. How many of the following statements are correct?
A. The metre bridge works on the Wheatstone bridge principle.
B. At balance, the galvanometer's own resistance does not affect the result.
C. A metre bridge is best for very small resistances, below 0.1 Ω.
D. Resistivity of a wire depends on its length.
(a) Three (b) One (c) Two (d) Four
36. Choose the correct set of statements about verifying Ohm's law.
A. The ammeter is in series and the voltmeter is in parallel with the wire.
B. An ideal voltmeter has zero resistance.
C. The slope of a V vs I graph gives the resistance.
D. Large currents give better results because the wire heats less.
(a) A and B only (b) A and C only (c) B and D only (d) A, C and D only
37. How many of these statements about the half-deflection method are correct?
A. When R is far larger than S, G is nearly equal to S.
B. Figure of merit is the current needed for one division of deflection.
C. A galvanometer with a smaller figure of merit is more sensitive.
D. R should be kept small so that the deflection is large.
(a) Two (b) Four (c) One (d) Three
38. Choose the correct set of statements about the metre bridge.
A. If X and R are interchanged, the balance length becomes 100 − l.
B. Changing the emf of the cell shifts the balance point.
C. The bridge is most sensitive when the balance point is near the middle of the wire.
D. Interchanging the cell and galvanometer does not change the balance condition.
(a) A, C and D only (b) A and B only (c) B and C only (d) B, C and D only
39. For a test wire of length 0.50 m and diameter 0.40 mm, an Ohm's law experiment gives:
| V (V) | 0.5 | 1.0 | 1.5 | 2.0 |
|---|---|---|---|---|
| I (A) | 0.10 | 0.20 | 0.30 | 0.40 |
The resistivity of the material is about (a) 6.3 × 10⁻⁷ Ω m (b) 1.26 × 10⁻⁶ Ω m (c) 2.5 × 10⁻⁶ Ω m (d) 5.0 × 10⁻⁶ Ω m
40. V–I graphs of the same metal wire at two temperatures are straight lines through the origin. Line P has slope 6 Ω and line Q has slope 4 Ω. Which line was taken at the higher temperature? (a) Q, since a metal's resistance falls when heated (b) Both at the same temperature, since both lines are straight (c) P, since a metal's resistance rises when heated (d) Q, since a smaller slope means more current
41. In the half-deflection method, E = 2.0 V and R = 5000 Ω give 30 divisions. A shunt of 50 Ω brings the deflection to 15 divisions. The galvanometer resistance and figure of merit are about (a) 49.5 Ω, 1.32 × 10⁻⁵ A/div (b) 50.5 Ω, 6.6 × 10⁻⁵ A/div (c) 5000 Ω, 1.32 × 10⁻⁵ A/div (d) 50.5 Ω, 1.32 × 10⁻⁵ A/div
Passage for Q42–43: In a metre bridge, a coil of wire X sits in the left gap and a 6.0 Ω resistor in the right gap. The null point is at 40.0 cm from the left end. The coil's wire is 0.80 m long with diameter 0.40 mm.
42. The resistance of the coil X is (a) 9.0 Ω (b) 4.0 Ω (c) 2.4 Ω (d) 6.0 Ω
43. The resistivity of the coil's material is about (a) 6.28 × 10⁻⁷ Ω m (b) 1.57 × 10⁻⁷ Ω m (c) 2.51 × 10⁻⁶ Ω m (d) 3.14 × 10⁻⁷ Ω m
44. In a metre bridge with X in the left gap and R = 20 Ω in the right gap, balance is at 40 cm from the left end. A resistor equal to X is now joined in parallel with X. The new balance point is at (a) 20 cm (b) 33.3 cm (c) 40 cm (d) 25 cm
45. A galvanometer with G = 50 Ω has a figure of merit of 20 μA/division and 30 divisions on each side. To make it a voltmeter of range 3 V, the series resistance needed is (a) 5050 Ω (b) 5000 Ω (c) 4950 Ω (d) 4900 Ω
Level 4 answer key
| Q | Ans | Reason |
|---|---|---|
| 31 | a | Each step paired with its working formula |
| 32 | c | Jockey finds null, strips join gaps, rheostat varies current, shunt halves deflection |
| 33 | b | Straight line = ohmic; V–I slope = R; I–V slope = 1/R; upward bend = R rising |
| 34 | d | Interchange for end errors, middle balance, short current, many diameter readings |
| 35 | c | A and B true; the bridge suits moderate R; ρ is a material property |
| 36 | b | Ideal voltmeter has infinite resistance; large current heats the wire |
| 37 | d | A, B, C true; R is kept large so the deflection stays on the scale |
| 38 | a | Balance needs no galvanometer current, so emf does not shift it |
| 39 | b | R = 5 Ω; ρ = 5 × π(0.2 × 10⁻³)²/0.50 ≈ 1.26 × 10⁻⁶ Ω m |
| 40 | c | Larger slope = larger R = higher temperature for a metal |
| 41 | d | G = 5000 × 50/4950 ≈ 50.5 Ω; k = 2/(5050.5 × 30) ≈ 1.32 × 10⁻⁵ A/div |
| 42 | b | X = 6 × 40/60 = 4.0 Ω |
| 43 | a | ρ = 4 × π(0.2 × 10⁻³)²/0.80 ≈ 6.28 × 10⁻⁷ Ω m |
| 44 | d | X = 40/3 Ω; halved to 20/3 Ω; l/(100 − l) = 1/3 gives l = 25 cm |
| 45 | c | I_g = 20 × 30 = 600 μA; R_s = 3/(6 × 10⁻⁴) − 50 = 4950 Ω |