Chapter 6: Electronics
What you will learn
How to wire a p-n junction diode in forward and reverse bias, and read its I–V curve.
What knee voltage, dynamic resistance and reverse saturation current look like in a table.
How a Zener diode's reverse characteristic shows a sharp breakdown voltage.
How to sort a diode, an LED, a resistor and a capacitor from a mixed heap using a multimeter.
The mistakes that damage diodes in the lab and cost marks in NEET.
6.1 Experiment: Characteristic curves of a p-n junction diode
Aim: To draw the I–V characteristic curves of a p-n junction diode in forward bias and reverse bias.
Apparatus: p-n junction diode (silicon, such as 1N4007), 3 V battery for forward bias, 30–50 V supply for reverse bias, rheostat used as a potential divider, milliammeter (0–30 mA), microammeter (0–100 μA), voltmeters (0–1 V and 0–30 V), a protective resistor, one-way key.
Principle: In forward bias, the p-side is joined to the positive terminal. The barrier potential is reduced. Almost no current flows until the applied voltage nears the barrier potential (about 0.7 V for silicon, 0.3 V for germanium). After this knee voltage, the current rises steeply.
In reverse bias, the p-side is joined to the negative terminal. The barrier grows. Only a tiny current flows, carried by minority carriers. It is almost independent of the voltage, so it is called the reverse saturation current (a few μA, much less for silicon).

Only the battery is turned around between the two circuits, and the milliammeter is swapped for a microammeter because reverse current is about a thousand times smaller.
Procedure (forward bias):
Connect the circuit with the diode's p-side (anode) toward the positive terminal, through the rheostat and milliammeter.
Keep the rheostat at minimum output. Close the key.
Raise the voltage across the diode in steps of 0.1 V. Note V and I each time.
Near the knee, use smaller steps, since current changes fast there.
Stop before the current crosses the diode's safe rating.
Procedure (reverse bias):
Reverse the diode (or the battery). Replace the milliammeter by a microammeter and use the higher voltage supply.
Raise the reverse voltage in steps of 2 V or 5 V. Note V and I.
Keep well below the breakdown voltage of an ordinary diode.
Observation table layout:
| S. No. | Forward voltage V_F (V) | Forward current I_F (mA) | Reverse voltage V_R (V) | Reverse current I_R (μA) |
|---|---|---|---|---|
| 1 | 0.1 | 2 | ||
| 2 | 0.2 | 4 | ||
| 3 | 0.3 | 6 |
Graph: Plot I against V. Forward values go in the first quadrant (mA scale). Reverse values go in the third quadrant (μA scale). The scales on the two sides are different. The forward curve is flat, then bends sharply at the knee and rises steeply. The reverse curve hugs the voltage axis.
Result: The forward curve is non-linear with a knee voltage of about … V. The reverse current is very small and nearly constant. Dynamic forward resistance at … mA = … Ω.
Precautions:
Use a protective resistor in series so the forward current never exceeds the rating.
Use a milliammeter in forward bias and a microammeter in reverse bias.
Do not apply a reverse voltage near the breakdown value of an ordinary diode.
Keep the key open between readings so the junction does not heat up.
Sources of error:
Heating of the junction changes the current for the same voltage.
In reverse bias, a little of the measured current may be the voltmeter's own current.
Meter least counts are coarse near the knee.
Viva-style points:
A diode does not obey Ohm's law; its resistance depends on the voltage.
Forward resistance is tens of ohms; reverse resistance is megaohms. That is why a diode rectifies.
Germanium has a lower knee voltage but a larger reverse current than silicon.
Worked example 6.1: A silicon diode gives these forward readings: 0.5 V, 0.1 mA; 0.6 V, 0.8 mA; 0.7 V, 10 mA; 0.8 V, 30 mA. Estimate the knee voltage and the dynamic resistance between 0.7 V and 0.8 V.
Solution: The current shoots up after about 0.7 V, so the knee is near 0.7 V. r_d = (0.8 − 0.7)/(30 − 10) × 10⁻³ = 0.1/0.020 = 5 Ω.
Worked example 6.2: In reverse bias, a diode carries 1 μA at 10 V. Find its reverse resistance.
Solution: R = 10/(1 × 10⁻⁶) = 10⁷ Ω = 10 MΩ.
Worked example 6.3: An LED needs 20 mA and drops 2.0 V when lit. What series resistor is needed with a 5.0 V supply?
Solution: Voltage across the resistor = 5.0 − 2.0 = 3.0 V. R = 3.0/0.020 = 150 Ω.
6.2 Experiment: Characteristic curve of a Zener diode and its breakdown voltage
Aim: To draw the reverse characteristic of a Zener diode and find its reverse breakdown voltage.
Apparatus: Zener diode (for example a 6.2 V Zener), variable DC supply (0–15 V), series protective resistor (a few hundred ohms), milliammeter, voltmeter (0–15 V), key.
Principle: A Zener diode is a heavily doped p-n junction built to work in reverse breakdown. In reverse bias, the current stays almost zero until the voltage reaches the Zener voltage V_Z. Then the current rises sharply while the voltage across the diode stays nearly constant. This is the basis of a voltage regulator. In forward bias it behaves like an ordinary diode.
The series resistor R_S limits the current:

The Zener's cathode faces the positive side, and the series resistor takes up the extra voltage once breakdown begins.
Procedure:
Connect the Zener in reverse bias (cathode, the end with the band, toward positive) in series with R_S and the milliammeter. Connect the voltmeter across the Zener.
Increase the supply voltage in small steps. Note the voltage across the Zener and the current.
Near the breakdown, increase in very small steps. Note the voltage at which the current begins to rise sharply.
Continue a little beyond, without crossing the Zener's maximum current.
Plot reverse current against reverse voltage (third quadrant). Read V_Z where the curve turns sharply down.
Observation table layout:
| S. No. | Supply voltage (V) | Voltage across Zener V_R (V) | Reverse current I_R (mA) |
|---|---|---|---|
| 1 | |||
| 2 | |||
| 3 |
Graph: In reverse bias, the curve runs flat along the voltage axis, then turns almost vertically at V_Z. After breakdown, the voltage hardly changes over a wide range of current.
Result: Reverse breakdown voltage of the Zener diode = … V.
Precautions:
Never omit the series resistor. Without it, current after breakdown rises without limit and burns the Zener.
Increase the voltage slowly near breakdown.
Note the Zener's rated power and keep I_Z × V_Z below it.
Sources of error:
Heating of the Zener shifts V_Z slightly.
Meter least counts near the sharp turn.
Viva-style points:
Heavy doping gives a thin depletion layer and a very strong field, which pulls electrons out of bonds (Zener effect).
Breakdown in a Zener is reversible as long as the current is limited.
Zener diodes are used as voltage regulators, as reference voltages in chargers and power supplies.
Worked example 6.4: A Zener gives these reverse readings: 5.6 V, 0.0 mA; 5.9 V, 0.1 mA; 6.1 V, 0.5 mA; 6.2 V, 5 mA; 6.25 V, 15 mA. Estimate the breakdown voltage.
Solution: The current is negligible up to about 6.1 V, then jumps from 0.5 mA to 15 mA with only 0.15 V more. V_Z ≈ 6.2 V.
Worked example 6.5: A 10 V Zener is used with R_S = 500 Ω and an input of 15 V. The load is 2 kΩ. Find I_S, I_L and I_Z.
Solution: I_S = (15 − 10)/500 = 10 mA. I_L = 10/2000 = 5 mA. I_Z = 10 − 5 = 5 mA.
6.3 Experiment: Identifying a diode, an LED, a resistor and a capacitor
Aim: To identify a diode, an LED, a resistor and a capacitor from a mixed collection of such items.
Apparatus: Multimeter (used as an ohmmeter), the mixed components, a 3 V battery with a 100 Ω series resistor for testing LEDs.
Principle: In the ohmmeter mode, the multimeter sends a small current through the component and shows its resistance. Each component responds in a different way when the leads are applied, and again when they are reversed.
| Component | Look | Ohmmeter, one way | Ohmmeter, leads reversed | Extra check |
|---|---|---|---|---|
| Resistor | Two leads, colour bands | Steady, finite value | Same value | No light, no direction |
| Diode | Two leads, black or glass body with a band (cathode) | Low resistance | Very high resistance | One-way, no light |
| LED | Two leads (longer one is anode), coloured transparent dome | Low resistance and may glow faintly | Very high resistance | Glows when forward biased with the battery |
| Capacitor | Two leads; electrolytic ones marked with a stripe for negative | Needle deflects, then falls back to very high resistance | Same brief deflection, then very high resistance | Charging effect, no steady current |
Procedure:
Set the multimeter to a resistance range. Touch its probes to the two leads of an item. Note the reading.
Reverse the probes and note the reading again.
Equal readings both ways: a resistor.
Low one way, high the other way: a diode or an LED. Connect it across the battery with the 100 Ω resistor in forward bias. If it glows, it is an LED; if not, it is a diode.
A brief swing that dies down to a very high value, both ways: a capacitor.
Observation table layout:
| Item | Reading one way | Reading reversed | Glows? | Identified as |
|---|---|---|---|---|
| A | ||||
| B | ||||
| C | ||||
| D |
Result: Item … is a resistor, … is a diode, … is an LED and … is a capacitor.
Precautions:
Discharge capacitors by shorting their leads before testing.
Never test an LED directly on a battery without a series resistor.
Do not touch both probe tips with your fingers; your body adds a parallel resistance.
Viva-style points:
A capacitor blocks steady DC but lets a charging current flow for a moment.
An LED is a forward-biased diode made of a compound semiconductor such as GaAsP; its colour depends on the band gap.
An LED usually needs about 1.8–3 V forward voltage, more than a silicon diode's 0.7 V.
Worked example 6.6: Four items give these ohmmeter results. P: 470 Ω both ways. Q: 30 Ω one way, very high the other; does not glow. R: brief swing to low, then very high, both ways. S: low one way, very high the other; glows red on the battery test. Identify them.
Solution: P is a resistor (same both ways). Q is a diode (one-way, no light). R is a capacitor (charging swing). S is an LED (one-way and glows).
Quick revision
Forward bias: p to +. Current small until the knee (0.7 V Si, 0.3 V Ge), then steep.
Reverse bias: tiny, almost constant saturation current in μA. Use a microammeter.
Dynamic resistance r_d = ΔV/ΔI on the steep part.
Zener in reverse bias: sharp rise of current at V_Z with nearly constant voltage. Always use a series resistor.
I_S = (V_in − V_Z)/R_S; I_Z = I_S − I_L.
Ohmmeter test: resistor same both ways; diode one-way; LED one-way and glows; capacitor brief swing then very high.
NEET traps
Using the same current scale for forward and reverse parts of the graph. Forward is in mA, reverse in μA.
Thinking reverse current grows steadily with voltage before breakdown. It stays nearly constant.
Connecting a Zener in forward bias and expecting regulation.
Forgetting that the Zener current is the series current minus the load current.
Calling a component a capacitor because it shows high resistance. A diode reversed also shows high resistance; only a capacitor shows the brief charging swing both ways.
Taking dynamic resistance as V/I at a point instead of ΔV/ΔI.
Practice MCQs: Chapter 6
Level 1: Concept check
1. The knee voltage of a silicon diode is about (a) 0.3 V (b) 0.7 V (c) 1.7 V (d) 7 V
2. In the reverse bias part of the diode experiment, the current is measured with (a) an ammeter of range 0–5 A (b) a milliammeter (c) a voltmeter (d) a microammeter
3. A p-n junction is forward biased when (a) the p-side is joined to the positive terminal (b) the n-side is joined to the positive terminal (c) both sides are joined to the positive terminal (d) no battery is joined
4. The reverse saturation current of a diode is carried by (a) majority carriers (b) holes only (c) minority carriers (d) fixed ions
5. A Zener diode is normally used (a) in forward bias as a rectifier (b) as a light source (c) as an amplifier (d) in reverse bias as a voltage regulator
6. After breakdown, the voltage across a Zener diode (a) rises sharply (b) stays nearly constant (c) falls to zero (d) changes sign
7. A resistor tested with an ohmmeter shows (a) the same reading both ways (b) low one way and high the other (c) a brief swing, then very high (d) zero both ways
8. A capacitor tested with an ohmmeter shows (a) the same finite reading both ways (b) low resistance one way only (c) a brief deflection, then very high resistance, both ways (d) zero resistance both ways
9. An LED can be told apart from an ordinary diode because it (a) conducts one way only (b) emits light when forward biased (c) has colour bands (d) shows a charging swing
10. The series resistor in a Zener test circuit is used to (a) raise the Zener voltage (b) cut the reverse saturation current (c) put the Zener in forward bias (d) limit the current after breakdown
Level 2: NEET standard
11. A diode's forward current rises from 5 mA to 15 mA when the voltage rises from 0.70 V to 0.75 V. Its dynamic resistance is (a) 5 Ω (b) 50 Ω (c) 0.5 Ω (d) 140 Ω
12. A diode carries 2 μA at a reverse voltage of 20 V. Its reverse resistance is (a) 10 kΩ (b) 1 MΩ (c) 10 MΩ (d) 40 MΩ
13. The knee voltage of a germanium diode is about (a) 0.7 V (b) 0.3 V (c) 1.1 V (d) 3.0 V
14. An LED drops 2.2 V at 15 mA. The series resistor needed with a 5.0 V supply is about (a) 333 Ω (b) 147 Ω (c) 120 Ω (d) 187 Ω
15. A 6.0 V Zener with R_S = 200 Ω is fed from 10 V with no load. The Zener current is (a) 20 mA (b) 50 mA (c) 30 mA (d) 80 mA
16. An 8.0 V Zener with R_S = 400 Ω is fed from 12 V and supplies a 1.6 kΩ load. The Zener current is (a) 10 mA (b) 15 mA (c) 5 mA (d) 2.5 mA
17. A Zener gives these reverse readings: 4.5 V, 0 mA; 4.8 V, 0.05 mA; 5.0 V, 0.3 mA; 5.1 V, 6 mA; 5.12 V, 18 mA. Its breakdown voltage is about (a) 4.5 V (b) 5.1 V (c) 4.8 V (d) 5.5 V
18. The I–V graph of a diode uses different current scales in the first and third quadrants because (a) forward current is in μA (b) reverse voltages are very small (c) the graph must look symmetric (d) forward current is in mA while reverse current is in μA
19. An item shows low resistance one way and very high the other way, and does not glow on the battery test. It is (a) a resistor (b) a capacitor (c) a diode (d) an LED
20. A 5.6 V Zener carries 25 mA in breakdown. The power it dissipates is (a) 0.14 W (b) 1.4 W (c) 0.22 W (d) 140 W
21. Beyond the knee, the forward I–V curve of a diode is (a) horizontal (b) steep and nearly straight (c) falling (d) flat at zero current
22. A student uses a microammeter in the forward bias circuit and raises the voltage to 0.8 V. The microammeter will (a) read correctly (b) read zero (c) read a negative value (d) be overloaded and may be damaged
Level 3: Challenge
23. A 9.0 V Zener (maximum safe current 15 mA) is fed from 15 V through 300 Ω. To keep the Zener current within its rating, the load resistance must not exceed (a) 1.8 kΩ (b) 600 Ω (c) 450 Ω (d) 3.0 kΩ
24. A 6.0 V Zener with R_S = 100 Ω feeds a 600 Ω load. As the input rises from 9 V to 12 V, the Zener current changes from (a) 30 mA to 60 mA (b) 10 mA to 10 mA (c) 20 mA to 50 mA (d) 20 mA to 30 mA
25. A silicon diode (drop 0.7 V) is forward biased by a 2.7 V cell through a 100 Ω resistor. The current is (a) 27 mA (b) 7 mA (c) 34 mA (d) 20 mA
26. The diode in Q25 is reversed, with the same cell and resistor. The current is now (a) 20 mA (b) nearly zero, a few μA at most (c) 27 mA (d) 2.7 A
27. The slope dI/dV of the forward curve is larger at 20 mA than at 2 mA. So the dynamic resistance is (a) smaller at 20 mA (b) larger at 20 mA (c) the same at both (d) infinite at 20 mA
28. An item conducts and glows when the battery test is done one way, and shows very high resistance when reversed. It is (a) a resistor (b) a capacitor (c) an LED (d) an ordinary silicon diode
29. Assertion (A): An LED should be tested on a battery only through a series resistor. Reason (R): A capacitor shows a brief deflection on an ohmmeter. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true
30. Statement I: Before breakdown, the reverse current of a diode rises in proportion to the reverse voltage. Statement II: The knee voltage of a germanium diode is lower than that of a silicon diode. (a) Both true (b) Both false (c) I true, II false (d) I false, II true
Answer key with reasons
| Q | Ans | Reason |
|---|---|---|
| 1 | b | Barrier potential of Si |
| 2 | d | Reverse current is in μA |
| 3 | a | p to + lowers the barrier |
| 4 | c | Thermally generated minority carriers |
| 5 | d | Constant voltage in breakdown |
| 6 | b | Current changes, voltage holds |
| 7 | a | Resistor has no direction |
| 8 | c | Charging current dies away |
| 9 | b | Only the LED gives light |
| 10 | d | Prevents burning after breakdown |
| 11 | a | 0.05 V/0.010 A = 5 Ω |
| 12 | c | 20/(2 × 10⁻⁶) = 10⁷ Ω |
| 13 | b | Ge barrier about 0.3 V |
| 14 | d | 2.8 V/0.015 A = 187 Ω |
| 15 | a | (10 − 6)/200 = 20 mA |
| 16 | c | I_S = 10 mA, I_L = 5 mA, I_Z = 5 mA |
| 17 | b | Sharp rise at about 5.1 V |
| 18 | d | Currents differ by about a thousand times |
| 19 | c | One-way, no light |
| 20 | a | 5.6 × 0.025 = 0.14 W |
| 21 | b | Current rises fast after the knee |
| 22 | d | Forward current is in mA |
| 23 | a | I_S = 20 mA; need I_L at least 5 mA; R_L at most 9/0.005 = 1.8 kΩ |
| 24 | c | I_L = 10 mA; I_S = 30 mA then 60 mA |
| 25 | d | (2.7 − 0.7)/100 = 20 mA |
| 26 | b | Reverse bias blocks |
| 27 | a | r_d = dV/dI falls as slope dI/dV rises |
| 28 | c | One-way conduction with light |
| 29 | b | Both true but unrelated |
| 30 | d | Reverse current is nearly constant; Ge knee is about 0.3 V |
Chapter 6 revision sheet
One-page summary
Forward bias: p-side to the positive terminal. The current stays tiny until the knee voltage, then rises steeply.
Knee (threshold) voltage is about 0.7 V for silicon and about 0.3 V for germanium.
Reverse bias widens the depletion layer. Only a tiny reverse saturation current (nA to μA) flows, almost independent of voltage.
Use a milliammeter in forward bias and a microammeter in reverse bias.
Dynamic resistance r_d = ΔV/ΔI, read from the slope of the curve. It falls as forward current grows.
A diode is non-ohmic: its I–V graph is not a straight line through the origin.
A Zener diode is heavily doped and is used in reverse bias. At breakdown, its voltage stays almost constant while current rises.
Zener breakdown is not destructive if a series resistor limits the current. In forward bias, a Zener acts like an ordinary diode.
Zener regulator: I_series = (V_in − V_Z)/R_s, I_load = V_Z/R_L, I_Z = I_series − I_load.
Power in a Zener = V_Z × I_Z.
Identification with a multimeter or battery–bulb test: resistor conducts both ways equally; diode conducts one way; LED conducts one way and glows; capacitor gives a brief kick that dies to zero.
A red LED needs about 1.8 V forward voltage, more than a silicon diode.
Must-remember table
| Item | Value or rule | How it shows in the lab |
|---|---|---|
| Si knee voltage | ≈ 0.7 V | Current rises sharply after 0.7 V |
| Ge knee voltage | ≈ 0.3 V | Earlier rise than Si |
| Reverse current | nA to μA | Microammeter reading, nearly flat |
| Dynamic resistance | ΔV/ΔI | Slope of the steep part |
| Zener current | (V_in − V_Z)/R_s − V_Z/R_L | Regulator calculation |
| Resistor | Same current both directions | Ohmic |
| Diode | One direction only | No light |
| LED | One direction, glows | Forward voltage ≈ 1.8 V (red) |
| Capacitor | Brief deflection, then zero | Charges and blocks DC |
Memory aids
"P to Plus, Pass": p-side to plus means forward bias, current passes.
"Seven Silicon, Three Germanium": knee voltage 0.7 V for Si, 0.3 V for Ge.
"Zener Zips at a fixed voltage": after breakdown, the voltage holds steady while current zips up.
"R-D-L-C: Both, One, One-and-Glow, Kick": Resistor both ways, Diode one way, LED one way and glows, Capacitor a brief kick.
"Milli Forward, Micro Reverse": milliammeter for forward current, microammeter for reverse current.
Concept connections
p-n junction theory, Zener diodes and LEDs are covered in Physics Book 19: Electronic Devices.
Series-resistor and current-division calculations use Physics Book 12: Current Electricity.
Capacitor charging behaviour in the identification test links to Physics Book 11: Electrostatics.
Practice MCQs: Chapter 6, Level 4 (new NEET pattern)
31. Match List I (component) with List II (behaviour in a simple test).
List I: (A) Resistor; (B) Diode; (C) LED; (D) Capacitor
List II: (i) Conducts one way and glows; (ii) Brief deflection that dies to zero; (iii) Same reading in both directions; (iv) Conducts one way, no light
(a) A-iv, B-iii, C-i, D-ii (b) A-iii, B-i, C-iv, D-ii (c) A-ii, B-iv, C-i, D-iii (d) A-iii, B-iv, C-i, D-ii
32. Match List I (region of a characteristic) with List II (feature).
List I: (A) Forward bias below the knee; (B) Forward bias above the knee; (C) Reverse bias before breakdown; (D) Zener breakdown region
List II: (i) Voltage nearly constant while current rises; (ii) Tiny, nearly constant current of order μA; (iii) Very small current; (iv) Current rises steeply
(a) A-iv, B-iii, C-i, D-ii (b) A-iii, B-iv, C-ii, D-i (c) A-iii, B-ii, C-iv, D-i (d) A-ii, B-iv, C-iii, D-i
33. Match List I (quantity) with List II (typical value).
List I: (A) Knee voltage of a Si diode; (B) Knee voltage of a Ge diode; (C) Reverse saturation current of a Si diode; (D) Forward voltage of a red LED
List II: (i) About 1.8 V; (ii) About 0.3 V; (iii) About 0.7 V; (iv) Of the order of nA to μA
(a) A-iii, B-ii, C-iv, D-i (b) A-ii, B-iii, C-iv, D-i (c) A-iii, B-iv, C-ii, D-i (d) A-i, B-ii, C-iv, D-iii
34. Match List I (circuit part) with List II (purpose).
List I: (A) Series resistor with a Zener; (B) Milliammeter in the forward-bias circuit; (C) Microammeter in the reverse-bias circuit; (D) Rheostat used as a potential divider
List II: (i) Varies the applied voltage; (ii) Limits the current; (iii) Reads the forward current; (iv) Reads the tiny reverse current
(a) A-iii, B-ii, C-i, D-iv (b) A-ii, B-iv, C-iii, D-i (c) A-ii, B-iii, C-iv, D-i (d) A-i, B-iii, C-iv, D-ii
35. How many of the following statements are correct?
A. Dynamic resistance of a diode is ΔV/ΔI at the operating point.
B. Forward dynamic resistance decreases as the forward current increases.
C. Before breakdown, the reverse current depends strongly on the reverse voltage.
D. Zener diodes are heavily doped.
(a) Two (b) Four (c) One (d) Three
36. Choose the correct set of statements about a Zener diode.
A. It is used in reverse bias as a voltage regulator.
B. Zener breakdown always destroys the diode.
C. Beyond breakdown, the voltage across it stays nearly constant.
D. In forward bias, it behaves like an ordinary diode.
(a) A, C and D only (b) A and B only (c) B and C only (d) B, C and D only
37. How many of these statements about identifying components are correct?
A. A capacitor gives a brief deflection that falls to zero.
B. An LED can be told apart from an ordinary diode because it glows in forward bias.
C. A resistor conducts in one direction only.
D. A healthy diode conducts equally in both directions.
(a) Three (b) One (c) Two (d) Four
38. Choose the correct set of statements about a p-n junction diode.
A. In forward bias, the p-side is joined to the positive terminal.
B. In reverse bias, the depletion layer becomes wider.
C. The knee voltage of germanium is greater than that of silicon.
D. A diode is a non-ohmic device.
(a) A and C only (b) B and C only (c) C and D only (d) A, B and D only
39. Forward-bias readings for a silicon diode:
| V (V) | 0.60 | 0.65 | 0.70 | 0.75 |
|---|---|---|---|---|
| I (mA) | 2 | 6 | 14 | 30 |
The dynamic resistance between 0.70 V and 0.75 V is about (a) 5 Ω (b) 3.1 Ω (c) 25 Ω (d) 50 Ω
40. A Zener diode's reverse characteristic is vertical at 6.2 V: the voltage stays at 6.2 V while the current rises from 5 mA to 25 mA. The power dissipated in the Zener at 25 mA is (a) 31 mW (b) 124 mW (c) 155 mW (d) 248 mW
41. An 8 V Zener is fed from a 12 V supply through a 200 Ω series resistor. A 1 kΩ load is connected across the Zener. The current through the Zener is (a) 12 mA (b) 20 mA (c) 8 mA (d) 28 mA
Passage for Q42–43: A student gets four unlabelled components P, Q, R and S. With a battery and a sensitive meter: P conducts in one direction only and gives no light; Q conducts in one direction and glows; R gives the same reading both ways; S gives a brief kick that dies to zero in both directions.
42. Which component is the capacitor? (a) P (b) Q (c) R (d) S
43. If P is connected in reverse with 5 V, the current through it is (a) The same as the forward current (b) Large, limited only by the meter (c) Very small, a few μA or less (d) Large enough to make it glow
44. A silicon diode (forward drop 0.7 V) is in series with a 1.0 kΩ resistor across a 5.0 V battery, in forward bias. The current is (a) 5.0 mA (b) 4.3 mA (c) 5.7 mA (d) 0.7 mA
45. A 5 V Zener with a 100 Ω series resistor feeds a 500 Ω load. The input voltage varies from 8 V to 12 V. The maximum current through the Zener is (a) 60 mA (b) 70 mA (c) 50 mA (d) 20 mA
Level 4 answer key
| Q | Ans | Reason |
|---|---|---|
| 31 | d | Resistor both ways, diode one way, LED glows, capacitor brief kick |
| 32 | b | Below knee small, above knee steep, reverse tiny, Zener region flat voltage |
| 33 | a | Si 0.7 V, Ge 0.3 V, reverse current nA–μA, red LED about 1.8 V |
| 34 | c | Resistor limits, mA forward, μA reverse, divider varies voltage |
| 35 | d | A, B, D true; reverse saturation current is nearly independent of voltage |
| 36 | a | With a series resistor, breakdown is safe and reversible |
| 37 | c | A and B true; a resistor conducts both ways; a diode conducts one way |
| 38 | d | Ge knee (0.3 V) is lower than Si (0.7 V) |
| 39 | b | r_d = 0.05 V/0.016 A ≈ 3.1 Ω |
| 40 | c | P = 6.2 × 0.025 = 0.155 W = 155 mW |
| 41 | a | Series current (12 − 8)/200 = 20 mA; load 8 mA; Zener 12 mA |
| 42 | d | Capacitor charges briefly, then blocks DC |
| 43 | c | Reverse-biased diode passes only the tiny saturation current |
| 44 | b | I = (5.0 − 0.7)/1000 = 4.3 mA |
| 45 | a | I_s max = (12 − 5)/100 = 70 mA; I_L = 10 mA; I_Z = 60 mA |