Chapter 9 of 11 · 25 min read

Chapter 7: Physical Chemistry Experiments

This chapter joins four lab experiments to theory you already know: calorimetry (thermodynamics), colloids, and rate laws (kinetics). NEET questions here are usually short calculations or “why is this done” reasoning.

What you will learn

  • How a simple calorimeter works and what its water equivalent means.

  • How to find the enthalpy of solution of CuSO₄ and why anhydrous and hydrated salts differ.

  • Why the enthalpy of neutralisation of any strong acid by any strong base is nearly constant.

  • How lyophilic and lyophobic sols are prepared and how they differ.

  • How the iodide–H₂O₂ “iodine clock” reaction gives the order of reaction.

7.1 Calorimetry basics

In school labs a polythene bottle or a beaker inside an insulated box serves as the calorimeter. It has a lid, a thermometer reading to 0.1 °C and a stirrer (Figure 7.1). The idea is the same as a thermos flask that keeps chai hot: little heat escapes, so the heat released by the reaction stays in the solution and shows up as a temperature change.

q=(mc+W) ΔTq = (m c + W)\,\Delta T

Here m is the mass of solution, c its specific heat (4.18 J g⁻¹ K⁻¹ for dilute solutions), W the water equivalent (heat capacity) of the calorimeter in J K⁻¹, and ΔT the temperature change.

W is found by mixing known masses of hot and cold water. The heat lost by hot water minus the heat gained by cold water is the heat taken up by the calorimeter.

Sign rule: a temperature rise means heat was released, so ΔH is negative.

ΔH=−qn(n=moles reacting or dissolving)\Delta H = -\frac{q}{n} \quad (n = \text{moles reacting or dissolving})

7.2 Enthalpy of solution of copper sulphate

Enthalpy of solution is the enthalpy change when 1 mol of a substance dissolves in a large amount of solvent. Procedure: put a known volume of water in the calorimeter, note its steady temperature, add a weighed amount of powdered CuSO₄, stir until dissolved, and note the highest (or lowest) temperature.

ΔsolH=−(mc+W) ΔT×Mw\Delta_{sol}H = -\frac{(m c + W)\,\Delta T \times M}{w}

where w is the mass of salt taken and M its molar mass.

Two forms behave very differently:

SaltApprox. ΔsolH (kJ mol⁻¹)Temperature changeWhy
Anhydrous CuSO₄ (white)−66.5RisesCu²⁺ gets hydrated for the first time; hydration enthalpy released exceeds lattice enthalpy
CuSO₄·5H₂O (blue)+11.7Falls slightlyIons are already hydrated; breaking the lattice needs more energy than is released

By Hess's law the difference gives the enthalpy of hydration of the salt:

CuSO4(s)+5H2O(l)→CuSO4⋅5H2O(s)ΔH=−66.5−11.7=−78.2 kJ mol−1\mathrm{CuSO_4(s) + 5H_2O(l) \rightarrow CuSO_4 \cdot 5H_2O(s)} \qquad \Delta H = -66.5 - 11.7 = -78.2\ \text{kJ mol}^{-1}

Powder the salt so it dissolves quickly; slow dissolving lets heat leak out before the peak temperature is read.

7.3 Enthalpy of neutralisation

Enthalpy of neutralisation is the enthalpy change when one mole of water forms from H⁺ of an acid and OH⁻ of a base in dilute solution.

For any strong acid and strong base, both are fully ionised. The spectator ions do nothing. The only real change is:

H+(aq)+OH−(aq)→H2O(l)ΔH≈−57 kJ mol−1\mathrm{H^+(aq) + OH^-(aq) \rightarrow H_2O(l)} \qquad \Delta H \approx -57\ \text{kJ mol}^{-1}

So HCl + NaOH, HNO₃ + KOH and H₂SO₄ + NaOH all give about −57 kJ per mole of water formed (about −13.7 kcal). With a weak acid or weak base, part of the heat is used up in ionising the weak electrolyte, so the value is less negative. CH₃COOH + NaOH gives about −55 kJ mol⁻¹. (HF is an exception: hydration of the small F⁻ ion makes its value more negative.)

Procedure: take 100 mL of 1.0 M HCl and 100 mL of 1.0 M NaOH at the same temperature. Pour both into the calorimeter, stir, and record the highest temperature. Then:

ΔneutH=−(mc+W) ΔTnH2O\Delta_{neut}H = -\frac{(m c + W)\,\Delta T}{n_{H_2O}}

The moles of water formed equal the moles of the limiting reagent (count H⁺ and OH⁻, not acid and base molecules).

Figure 7.1 · Simple calorimeter for the enthalpy of neutralisation
Figure 7.1 · Simple calorimeter for the enthalpy of neutralisation

The acid and base are mixed inside the insulated vessel and stirred, and the thermometer records the highest temperature reached.

7.4 Lyophilic and lyophobic sols

A sol is a colloid of a solid in a liquid. Particle size lies between about 1 nm and 1000 nm. Lyophilic (solvent-loving) sols form on their own when the substance is mixed with the solvent. Lyophobic (solvent-hating) sols must be made by special methods and need a little electrolyte to stay stable.

PropertyLyophilicLyophobic
ExamplesStarch, gum arabic, egg albumin, gelatinFe(OH)₃, As₂S₃, Al(OH)₃, gold
PreparationSimply warm/stir with waterHydrolysis, double decomposition, Bredig's arc, peptisation
StabilityStable (solvation layer + charge)Less stable (charge only)
ReversibilityReversible: dried residue re-forms the sol with waterIrreversible
Effect of a little electrolyteNot easily coagulatedCoagulated easily
ViscosityHigher than waterAbout the same as water

Preparing lyophilic sols:

  • Starch sol: make a paste of about 0.5 g starch in a little cold water. Pour it into 100 mL of boiling water with constant stirring. Boil for a few minutes and cool.

  • Gum arabic sol: warm about 0.2 g of gum in 50 mL of water and stir.

  • Egg albumin sol: dissolve egg white in about 2% NaCl solution and shake gently.

Preparing lyophobic sols:

  • Ferric hydroxide sol (by hydrolysis): add 2% FeCl₃ solution drop by drop to boiling distilled water. A reddish-brown sol forms. FeCl₃ + 3H₂O → Fe(OH)₃ (sol) + 3HCl. The particles adsorb Fe³⁺ and carry a positive charge.

  • Arsenious sulphide sol (by double decomposition): pass H₂S into a cold, dilute solution of As₂O₃. A yellow sol forms. As₂O₃ + 3H₂S → As₂S₃ (sol) + 3H₂O. The particles adsorb HS⁻/S²⁻ and carry a negative charge.

  • Aluminium hydroxide sol: similar hydrolysis of an aluminium salt.

Excess electrolyte (HCl in the Fe(OH)₃ sol) is removed by dialysis through a parchment or cellophane membrane. Too much electrolyte would coagulate the sol.

Hardy–Schulze rule: the ion that coagulates a sol is the one with charge opposite to the particles, and its power rises steeply with its charge. For negative As₂S₃: Al³⁺ > Ba²⁺ > Na⁺. For positive Fe(OH)₃: PO₄³⁻ > SO₄²⁻ > Cl⁻. A lyophilic sol added to a lyophobic sol protects it from coagulation; gold number measures this protective power (smaller gold number, better protection).

7.5 Kinetics of the reaction of iodide ions with H₂O₂

In acid solution, hydrogen peroxide oxidises iodide to iodine:

H2O2+2I−+2H+→I2+2H2O\mathrm{H_2O_2 + 2I^- + 2H^+ \rightarrow I_2 + 2H_2O}

Experiments show the rate law (at fixed [H⁺]):

rate=k[H2O2][I−]\text{rate} = k[\mathrm{H_2O_2}][\mathrm{I^-}]

The reaction is first order in each reactant and second order overall. This fits a slow first step: H₂O₂ + I⁻ → H₂O + IO⁻, followed by fast steps in which IO⁻, H⁺ and I⁻ give I₂.

The iodine clock method. Each flask has KI, dilute H₂SO₄, starch and a small fixed amount of Na₂S₂O₃. H₂O₂ is added and a stopwatch started. Iodine forms but is at once turned back to iodide by thiosulphate:

I2+2S2O32−→2I−+S4O62−\mathrm{I_2 + 2S_2O_3^{2-} \rightarrow 2I^- + S_4O_6^{2-}}

When the thiosulphate is used up, free I₂ meets starch and the solution suddenly turns blue. The time t is the time needed to form a fixed amount of I₂. So the rate is proportional to 1/t.

To find the order with respect to I⁻, run several flasks with different [I⁻] and the same [H₂O₂], [H⁺] and thiosulphate, all at room temperature. Total volume is kept the same by adding water.

rate2rate1=t1t2=([I−]2[I−]1)n\frac{\text{rate}_2}{\text{rate}_1} = \frac{t_1}{t_2} = \left(\frac{[\mathrm{I^-}]_2}{[\mathrm{I^-}]_1}\right)^n

If doubling [I⁻] halves t, then n = 1. Since I⁻ is regenerated by thiosulphate during the clock period, [I⁻] stays almost constant in each run, which makes the analysis clean.

7.6 Worked examples

Worked example 7.1: 50 g of water at 30.0 °C is placed in a calorimeter. 50 g of water at 60.0 °C is added. The final temperature is 44.0 °C. Find the water equivalent W (c = 4.18 J g⁻¹ K⁻¹).

Solution: Heat lost by hot water = 50 × 4.18 × 16.0 = 3344 J. Heat gained by cold water = 50 × 4.18 × 14.0 = 2926 J. The calorimeter took 418 J for a 14.0 K rise. W = 418/14.0 = 29.9 J K⁻¹.

Worked example 7.2: 5.00 g of anhydrous CuSO₄ (M = 159.6) dissolves in 100 g of water in a calorimeter with W = 20 J K⁻¹. The temperature rises by 4.70 K. Find ΔsolH.

Solution: Heat capacity = 100 × 4.18 + 20 = 438 J K⁻¹. q = 438 × 4.70 = 2059 J. n = 5.00/159.6 = 0.03133 mol. ΔsolH = −2059/0.03133 = −65.7 kJ mol⁻¹. (Taking the solution mass as 100 g is the usual school approximation.)

Worked example 7.3: Why does a student see the temperature fall when dissolving blue vitriol, but rise with the white anhydrous salt?

Solution: CuSO₄·5H₂O already has hydrated Cu²⁺, so only lattice breaking (endothermic) dominates: ΔsolH ≈ +11.7 kJ mol⁻¹. White CuSO₄ releases a large hydration enthalpy as its ions get hydrated: ΔsolH ≈ −66.5 kJ mol⁻¹.

Worked example 7.4: 100 mL of 1.0 M HCl and 100 mL of 1.0 M NaOH, both at 27.0 °C, are mixed. Ignoring the calorimeter, find the expected rise in temperature (ΔneutH = −57.1 kJ mol⁻¹).

Solution: Water formed = 0.10 mol. Heat = 0.10 × 57100 = 5710 J. Mass = 200 g. ΔT = 5710/(200 × 4.18) = 6.83 K. Final temperature ≈ 33.8 °C.

Worked example 7.5: 50 mL of 1.0 M HCl and 50 mL of 1.0 M NaOH at 25.0 °C are mixed in a calorimeter (W = 30 J K⁻¹). The temperature reaches 31.4 °C. Find ΔneutH.

Solution: Heat capacity = 100 × 4.18 + 30 = 448 J K⁻¹. q = 448 × 6.4 = 2867 J. n(H₂O) = 0.050 mol. ΔneutH = −2867/0.050 = −57.3 kJ mol⁻¹.

Worked example 7.6: 200 mL of 0.50 M HCl is mixed with 100 mL of 0.50 M NaOH. Find the heat released and ΔT (ignore the calorimeter).

Solution: H⁺ = 0.10 mol, OH⁻ = 0.050 mol. NaOH is limiting, so 0.050 mol of water forms. Heat = 0.050 × 57.1 = 2.86 kJ. Mass = 300 g. ΔT = 2855/(300 × 4.18) = 2.28 K.

Worked example 7.7: Arrange NaCl, BaCl₂ and AlCl₃ in order of coagulating power for an As₂S₃ sol, and Na₃PO₄, Na₂SO₄ and NaCl for an Fe(OH)₃ sol.

Solution: As₂S₃ is negative, so the cation matters: AlCl₃ > BaCl₂ > NaCl. Fe(OH)₃ is positive, so the anion matters: Na₃PO₄ > Na₂SO₄ > NaCl.

Worked example 7.8: In an iodine clock run, [I⁻] = 0.010 M gives the blue colour in 80 s; 0.020 M gives 40 s; 0.040 M gives 20 s ([H₂O₂] fixed). Find the order with respect to I⁻.

Solution: Each doubling of [I⁻] halves t, so the rate doubles. 2 = 2ⁿ gives n = 1. The reaction is first order in I⁻.

Worked example 7.9 (NEET-hard): For rate = k[H₂O₂][I⁻], a run takes 60 s to turn blue. In a new run [I⁻] is tripled and [H₂O₂] is halved, with the same thiosulphate. How long will it take?

Solution: New rate = 3 × 0.5 = 1.5 times the old rate. Time is inversely proportional to rate: t = 60/1.5 = 40 s.

Quick revision

  • q = (mc + W)ΔT; temperature rise means ΔH negative.

  • ΔsolH: anhydrous CuSO₄ ≈ −66.5 kJ mol⁻¹ (warms); CuSO₄·5H₂O ≈ +11.7 kJ mol⁻¹ (cools); hydration ≈ −78.2 kJ mol⁻¹.

  • Strong acid + strong base: ΔneutH ≈ −57 kJ per mol of water; weak acid or base: less negative.

  • Lyophilic sols (starch, gum, albumin): direct mixing, reversible, stable. Lyophobic (Fe(OH)₃, As₂S₃): hydrolysis or double decomposition, irreversible.

  • Fe(OH)₃ sol positive; As₂S₃ sol negative. Hardy–Schulze: higher opposite charge, stronger coagulation.

  • H₂O₂ + 2I⁻ + 2H⁺ → I₂ + 2H₂O; rate = k[H₂O₂][I⁻]; rate ∝ 1/t in the clock method.

NEET traps

  • Dividing heat by moles of acid instead of moles of water formed (H₂SO₄ gives 2 mol H⁺ per mol).

  • Expecting −57 kJ mol⁻¹ for acetic acid or ammonia. Weak electrolytes give less heat.

  • Writing −13.7 kJ. It is −13.7 kcal, which is about −57 kJ.

  • Calling Fe(OH)₃ sol negative. It adsorbs Fe³⁺ and is positive.

  • Thinking the blue colour appears when the reaction is complete. It appears when the thiosulphate runs out.

  • Using the total volume of only one solution for mass in neutralisation; use the combined volume.

Practice MCQs: Chapter 7

Level 1: Concept check

1. The enthalpy of neutralisation of a strong acid by a strong base is about (a) −57 kJ mol⁻¹ (b) −13.7 kJ mol⁻¹ (c) +57 kJ mol⁻¹ (d) −114 kJ mol⁻¹

2. Dissolving anhydrous CuSO₄ in water is (a) endothermic (b) thermally neutral (c) exothermic (d) explosive

3. Which forms a lyophilic sol? (a) Fe(OH)₃ (b) As₂S₃ (c) Gold (d) Starch

4. Ferric hydroxide sol is prepared by (a) double decomposition (b) hydrolysis of FeCl₃ in boiling water (c) Bredig's arc (d) reduction with formaldehyde

5. The charge on As₂S₃ sol particles is (a) positive (b) zero (c) negative (d) sometimes positive, sometimes negative

6. In the iodine clock experiment, the blue colour appears when (a) all the thiosulphate has been used up (b) all the H₂O₂ has been used up (c) all the I⁻ has been used up (d) starch is added

7. The reaction studied in the iodide–H₂O₂ kinetics experiment is (a) 2H₂O₂ → 2H₂O + O₂ (b) H₂O₂ + 2I⁻ + 2H⁺ → I₂ + 2H₂O (c) I₂ + H₂O₂ → 2HIO (d) 2I⁻ + O₂ → I₂ + O₂²⁻

8. Heat changes in reactions are measured with a (a) burette (b) voltmeter (c) colorimeter (d) calorimeter

9. Lyophilic sols are (a) reversible and stable (b) irreversible and unstable (c) stabilised by charge only (d) always metallic

10. In the clock method, the rate of reaction is proportional to (a) t (b) t² (c) 1/t (d) the square root of t

Level 2: NEET standard

11. The enthalpy of neutralisation of CH₃COOH by NaOH is (a) more negative than −57 kJ mol⁻¹ (b) exactly −57 kJ mol⁻¹ (c) positive (d) less negative than −57 kJ mol⁻¹

12. The enthalpy of neutralisation is almost the same for all strong acid–strong base pairs because (a) all their salts are soluble (b) the net reaction is always H⁺ + OH⁻ → H₂O (c) the salts hydrolyse (d) the solutions are coloured

13. Excess electrolyte is removed from a freshly made Fe(OH)₃ sol by (a) peptisation (b) electrophoresis (c) dialysis (d) coagulation

14. A calorimeter (W = 40 J K⁻¹) holds 100 g of water. Heat needed to raise the temperature of both by 5.0 K (c = 4.18 J g⁻¹ K⁻¹) is (a) 2.29 kJ (b) 2.09 kJ (c) 0.20 kJ (d) 4.58 kJ

15. The best coagulant for Fe(OH)₃ sol is (a) NaCl (b) KNO₃ (c) BaCl₂ (d) Na₃PO₄

16. A starch sol is prepared by (a) hydrolysis (b) making a paste and pouring it into boiling water with stirring (c) Bredig's arc method (d) double decomposition

17. Heat released when 200 mL of 0.50 M HCl is mixed with 200 mL of 0.50 M NaOH (ΔneutH = −57.1 kJ mol⁻¹) is (a) 2.86 kJ (b) 11.4 kJ (c) 5.71 kJ (d) 57.1 kJ

18. Doubling [I⁻] halves the time for the blue colour. The order with respect to I⁻ is (a) 1 (b) 2 (c) 0 (d) 0.5

19. Arsenious sulphide sol is prepared by passing H₂S into (a) arsenic metal in water (b) AsCl₃ in NaOH (c) Na₃AsO₄ solution (d) a dilute solution of As₂O₃

20. ΔsolH of CuSO₄·5H₂O is positive while that of anhydrous CuSO₄ is negative because (a) the hydrate is insoluble (b) copper has different oxidation states in them (c) the anhydrous salt releases hydration enthalpy as its ions become hydrated, while the hydrate is already hydrated (d) they are dissolved at different temperatures

21. 100 mL of 1.0 M HCl is mixed with 100 mL of 1.0 M NaOH. Ignoring the calorimeter (c = 4.18 J g⁻¹ K⁻¹, ΔneutH = −57.1 kJ mol⁻¹), the temperature rises by about (a) 13.7 K (b) 6.8 K (c) 3.4 K (d) 1.4 K

22. Given ΔsolH(CuSO₄) = −66.5 kJ mol⁻¹ and ΔsolH(CuSO₄·5H₂O) = +11.7 kJ mol⁻¹, ΔH for CuSO₄(s) + 5H₂O(l) → CuSO₄·5H₂O(s) is (a) −78.2 kJ (b) −54.8 kJ (c) +78.2 kJ (d) −11.7 kJ

Level 3: Challenge

23. 50 mL of 1.0 M H₂SO₄ is mixed with 50 mL of 1.0 M NaOH (ΔneutH = −57.1 kJ mol⁻¹). The heat released is (a) 5.71 kJ (b) 11.42 kJ (c) 2.86 kJ (d) 8.57 kJ

24. For rate = k[H₂O₂][I⁻], both concentrations are doubled with the same thiosulphate. A run that took t seconds now takes (a) 2t (b) t/2 (c) 4t (d) t/4

25. 3.19 g of anhydrous CuSO₄ (M = 159.6) dissolves in a calorimeter whose total heat capacity (water + vessel) is 440 J K⁻¹. The temperature rises by 3.1 K. ΔsolH is about (a) +68.2 kJ mol⁻¹ (b) −68.2 kJ mol⁻¹ (c) −1.36 kJ mol⁻¹ (d) −34.1 kJ mol⁻¹

26. The protective power of a lyophilic colloid on a gold sol is expressed by its (a) gold number (b) coagulation value (c) Tyndall intensity (d) zeta potential

27. The correct order of coagulating power for As₂S₃ sol is (a) Na⁺ > Ba²⁺ > Al³⁺ (b) Ba²⁺ > Al³⁺ > Na⁺ (c) Cl⁻ > SO₄²⁻ > PO₄³⁻ (d) Al³⁺ > Ba²⁺ > Na⁺

28. In the iodine clock run, more Na₂S₂O₃ is added while everything else is unchanged. The blue colour appears (a) earlier (b) never (c) later (d) at the same time

29. Assertion (A): The enthalpy of neutralisation of HCl by NaOH is the same as that of HNO₃ by KOH. Reason (R): Both pairs are fully ionised, and the net change is H⁺ + OH⁻ → H₂O. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: Fe(OH)₃ sol is negatively charged. Statement II: Starch sol is a lyophobic sol. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1aH⁺ + OH⁻ → H₂O releases about 57 kJ
2cHydration enthalpy dominates
3dStarch disperses directly in water
4bFeCl₃ + 3H₂O → Fe(OH)₃ + 3HCl
5cAdsorbs S²⁻/HS⁻
6aFree I₂ then colours starch
7bAcidic oxidation of I⁻
8dMeasures heat by ΔT
9aSolvation keeps them stable
10cFixed I₂ amount formed in time t
11dHeat used to ionise the weak acid
12bSpectator ions take no part
13cIons pass the membrane, colloid does not
14a(418 + 40) × 5.0 = 2290 J
15dTrivalent anion for positive sol
16bDirect dispersion in hot water
17c0.10 mol water × 57.1 kJ
18aRate doubles when [I⁻] doubles
19dAs₂O₃ + 3H₂S → As₂S₃ + 3H₂O
20cHydrate ions already hydrated
21b5710/(200 × 4.18) = 6.8 K
22a−66.5 − (+11.7) by Hess's law
23cOH⁻ limiting: 0.050 mol water
24dRate rises four times
25b1364 J/0.0200 mol, temperature rose
26aSmaller gold number, better protection
27dHardy–Schulze: higher cation charge
28cMore I₂ must form first
29aR explains A exactly
30bFe(OH)₃ sol is positive; starch is lyophilic

Chapter 7 revision sheet

One-page summary

  • Calorimetry: heat exchanged q = (mc + W)ΔT, where W is the heat capacity of the calorimeter (J K⁻¹). A temperature rise means the process is exothermic (ΔH negative).

  • ΔH per mole = −q ÷ moles of the reacting substance (or of water formed in neutralisation).

  • ΔsolH of anhydrous CuSO₄ ≈ −66.5 kJ mol⁻¹ (solution warms); of CuSO₄·5H₂O ≈ +11.7 kJ mol⁻¹ (solution cools a little).

  • Hess's law: ΔhydH (CuSO₄ → CuSO₄·5H₂O) = −66.5 − 11.7 = −78.2 kJ mol⁻¹.

  • Strong acid + strong base: ΔneutH ≈ −57 kJ per mole of water, since the reaction is only H⁺ + OH⁻ → H₂O. With a weak acid or base it is less negative, because some heat is used to ionise it.

  • In neutralisation, moles of water = moles of the limiting H⁺ or OH⁻; total mass = total volume (density 1 g mL⁻¹).

  • Lyophilic sols (starch, gum, egg albumin): made by warming or mixing directly with water; reversible and stable.

  • Lyophobic sols: Fe(OH)₃ by adding FeCl₃ to boiling water (hydrolysis), positively charged; As₂S₃ by passing H₂S into As₂O₃ solution (double decomposition), negatively charged.

  • Excess electrolyte coagulates a lyophobic sol; remove it by dialysis.

  • Hardy–Schulze rule: the higher the charge on the oppositely charged ion, the stronger its coagulating power.

  • Clock reaction: H₂O₂ + 2I⁻ + 2H⁺ → I₂ + 2H₂O. Thiosulfate turns I₂ back to I⁻; blue starch–iodine appears only when thiosulfate is used up.

  • Initial rate ∝ 1/t (t = time for the blue colour). Rate = k[H₂O₂][I⁻]: doubling either concentration halves the time.

q=(mc+W) ΔTΔH=−qnq = (mc + W)\,\Delta T \qquad \Delta H = -\frac{q}{n}
I2+2S2O32−→2I−+S4O62−\mathrm{I_2 + 2S_2O_3^{2-} \rightarrow 2I^- + S_4O_6^{2-}}

Must-remember table

QuantityValue or ruleSign / note
ΔsolH, anhydrous CuSO₄≈ −66.5 kJ mol⁻¹Warms
ΔsolH, CuSO₄·5H₂O≈ +11.7 kJ mol⁻¹Cools
ΔhydH, CuSO₄≈ −78.2 kJ mol⁻¹By Hess's law
ΔneutH, strong acid + strong base≈ −57 kJ mol⁻¹Per mole of water
Specific heat of water4.18 J g⁻¹ K⁻¹Density 1 g mL⁻¹
Fe(OH)₃ solPositiveBest coagulant: [Fe(CN)₆]⁴⁻ > PO₄³⁻ > SO₄²⁻ > Cl⁻
As₂S₃ solNegativeBest coagulant: Al³⁺ > Ba²⁺ > Na⁺
Clock reactionRate ∝ 1/tFirst order in H₂O₂ and in I⁻

Memory aids

  • "Dry warms, Wet cools": anhydrous CuSO₄ warms water; the pentahydrate cools it.

  • "Fifty-seven, strong and steady": any strong acid with any strong base gives about −57 kJ per mole of water.

  • "Ferric Plus, Arsenic Minus": Fe(OH)₃ sol is positive, As₂S₃ sol is negative.

  • "Blue arrives when Thio dies": the blue colour appears only after all the thiosulfate is used up.

Concept connections

  • Enthalpy, Hess's law and heat capacity come from Chemistry Book 4: Chemical Thermodynamics.

  • Rate laws, order and initial-rate methods are in Chemistry Book 8: Chemical Kinetics.

  • Hydrolysis of FeCl₃ (used to make the sol) and the weak-acid ionisation behind the smaller ΔneutH are in Chemistry Book 6: Equilibrium; sols differ from true solutions (Chemistry Book 5: Solutions) in particle size.

Practice MCQs: Chapter 7, Level 4 (new NEET pattern)

31. Match List I with List II (approximate value in kJ mol⁻¹).

List I:

  • A. ΔsolH of CuSO₄·5H₂O

  • B. ΔsolH of anhydrous CuSO₄

  • C. ΔneutH of a strong acid with a strong base

  • D. ΔhydH of CuSO₄ to CuSO₄·5H₂O

List II:

  • (i) −78.2

  • (ii) +11.7

  • (iii) −57

  • (iv) −66.5

(a) A-iv, B-ii, C-iii, D-i (b) A-ii, B-i, C-iii, D-iv (c) A-ii, B-iv, C-i, D-iii (d) A-ii, B-iv, C-iii, D-i

32. Match List I (sol or step) with List II (method).

List I:

  • A. Starch sol

  • B. Fe(OH)₃ sol

  • C. As₂S₃ sol

  • D. Purifying a sol

List II:

  • (i) Dialysis

  • (ii) Double decomposition with H₂S

  • (iii) Hydrolysis of FeCl₃ in boiling water

  • (iv) Warming directly with water

(a) A-iii, B-iv, C-ii, D-i (b) A-iv, B-iii, C-ii, D-i (c) A-iv, B-ii, C-iii, D-i (d) A-i, B-iii, C-ii, D-iv

33. Match List I with List II.

List I:

  • A. Charge on Fe(OH)₃ sol

  • B. Charge on As₂S₃ sol

  • C. Best coagulant for Fe(OH)₃ sol (equal concentrations)

  • D. Best coagulant for As₂S₃ sol (equal concentrations)

List II:

  • (i) AlCl₃

  • (ii) Negative

  • (iii) K₄[Fe(CN)₆]

  • (iv) Positive

(a) A-iv, B-ii, C-iii, D-i (b) A-ii, B-iv, C-iii, D-i (c) A-iv, B-ii, C-i, D-iii (d) A-iv, B-iii, C-ii, D-i

34. Match List I (substance in the iodide clock reaction) with List II (role).

List I:

  • A. H₂O₂

  • B. Na₂S₂O₃

  • C. Starch

  • D. Dilute H₂SO₄

List II:

  • (i) Gives a blue colour with I₂

  • (ii) Removes I₂ as it forms, fixing the clock time

  • (iii) Oxidises I⁻ to I₂

  • (iv) Supplies H⁺ needed by the reaction

(a) A-ii, B-iii, C-i, D-iv (b) A-iii, B-i, C-ii, D-iv (c) A-iii, B-ii, C-i, D-iv (d) A-iv, B-ii, C-i, D-iii

35. How many of the following statements are correct?

  • A. Dissolving anhydrous CuSO₄ in water warms the solution.

  • B. Dissolving CuSO₄·5H₂O in water cools it slightly.

  • C. ΔhydH = ΔsolH(anhydrous) − ΔsolH(pentahydrate).

  • D. The heat capacity of the calorimeter is ignored in careful work.

(a) 1 (b) 2 (c) 3 (d) 4

36. Choose the correct set of statements.

  • A. ΔneutH for any strong acid with any strong base is about −57 kJ per mole of water.

  • B. For CH₃COOH + NaOH the value is more negative than −57 kJ mol⁻¹.

  • C. Mixing 100 mL of 0.5 M HCl with 100 mL of 1.0 M NaOH forms 0.05 mol of water.

  • D. In that mixture, the mass used for the heat calculation is 200 g.

(a) A, C and D only (b) A and B only (c) B and C only (d) A, B, C and D

37. How many of the following statements about sols are correct?

  • A. Lyophilic sols are reversible.

  • B. Fe(OH)₃ sol is negatively charged.

  • C. As₂S₃ sol is negative because it adsorbs sulphide-type ions.

  • D. A small amount of electrolyte coagulates a lyophobic sol.

  • E. Starch sol is a lyophilic sol.

(a) 1 (b) 2 (c) 3 (d) 4

38. Choose the correct set of statements about the iodide clock reaction.

  • A. The time for the blue colour is inversely proportional to the initial rate.

  • B. If doubling [I⁻] halves the time, the reaction is first order in I⁻.

  • C. The blue colour appears at once, even while thiosulfate is present.

  • D. The rate law is rate = k[H₂O₂][I⁻].

(a) A and C only (b) A, B and D only (c) B, C and D only (d) A, B, C and D

39. Data from an iodide clock experiment (fixed thiosulfate and acid):

Run[H₂O₂] (M)[I⁻] (M)Time for blue colour (s)
10.0100.01080
20.0200.01040
30.0100.02040
40.0200.020?

Order in H₂O₂, order in I⁻, and time for run 4 are: (a) 1, 1, 40 s (b) 2, 0, 20 s (c) 1, 1, 20 s (d) 1, 2, 10 s

40. 50.0 mL of 1.0 M HCl and 50.0 mL of 1.0 M NaOH, both at 25.0 °C, are mixed. A temperature–time graph rises sharply to a peak of 31.8 °C and then falls slowly. Taking the total mass as 100 g, c = 4.18 J g⁻¹ K⁻¹ and ignoring the calorimeter, ΔneutH is: (a) −56.8 kJ mol⁻¹ (b) −28.4 kJ mol⁻¹ (c) −113.7 kJ mol⁻¹ (d) −5.68 kJ mol⁻¹

41. In a clock experiment, a plot of 1/t (y-axis) against [I⁻] (x-axis), with all else fixed, is a straight line through the origin. This shows the reaction is: (a) zero order in I⁻ (b) first order in I⁻ (c) second order in I⁻ (d) independent of I⁻

Passage for Q42–43: 3.19 g of anhydrous CuSO₄ (M = 159.5 g mol⁻¹) is dissolved in 100 g of water in a calorimeter of heat capacity 50 J K⁻¹. The temperature rises by 2.80 K. Take m = 100 g and c = 4.18 J g⁻¹ K⁻¹.

42. Heat released is: (a) 1.17 kJ (b) 0.14 kJ (c) 2.62 kJ (d) 1.31 kJ

43. ΔsolH of anhydrous CuSO₄ from this data is: (a) +65.5 kJ mol⁻¹ (b) −65.5 kJ mol⁻¹ (c) −58.5 kJ mol⁻¹ (d) −6.55 kJ mol⁻¹

44. Using ΔsolH(anhydrous CuSO₄) = −66.5 kJ mol⁻¹ and ΔsolH(CuSO₄·5H₂O) = +11.7 kJ mol⁻¹, the heat released when 0.10 mol of anhydrous CuSO₄ becomes CuSO₄·5H₂O is: (a) 7.82 kJ (b) 5.48 kJ (c) 6.65 kJ (d) 1.17 kJ

45. From NaCl, Na₂SO₄, Na₃PO₄, BaCl₂ and AlCl₃ at equal concentrations, the fastest coagulants for Fe(OH)₃ sol and As₂S₃ sol respectively are: (a) NaCl; AlCl₃ (b) AlCl₃; Na₃PO₄ (c) Na₂SO₄; BaCl₂ (d) Na₃PO₄; AlCl₃

Level 4 answer key

QAnsReason
31d+11.7, −66.5, −57, −78.2
32bLyophilic direct, FeCl₃ hydrolysis, H₂S double decomposition, dialysis
33aPositive Fe(OH)₃ needs a high-charge anion; negative As₂S₃ needs Al³⁺
34cH₂O₂ oxidant, thiosulfate delays I₂, starch indicator, acid supplies H⁺
35cA, B, C true; W must be included
36aWeak acid gives a less negative value (heat used for ionisation)
37dA, C, D, E true; Fe(OH)₃ sol is positive
38bBlue appears only after thiosulfate is used up
39cEach doubling halves the time: first order in each; 80/4 = 20 s
40aq = 100 × 4.18 × 6.8 = 2842 J; 2842/0.050 = 56.8 kJ; exothermic
41bRate (∝ 1/t) directly proportional to [I⁻]
42d(418 + 50) × 2.80 = 1310 J
43b1310 J ÷ 0.0200 mol = 65.5 kJ; heat released, so negative
44aΔhydH = −78.2 kJ mol⁻¹; 0.10 × 78.2 = 7.82 kJ
45dPO₄³⁻ is the highest-charge anion; Al³⁺ the highest-charge cation
25 min left
‹
›