Chapter 4 of 11 · 28 min read

Chapter 2: Torque and Rotational Equilibrium

A force can push a body along, turn it, or do both. Torque measures the turning effect. This chapter shows how to compute torque and how to use it to decide whether a beam, a ladder or a see-saw stays balanced.

What you will learn

  • The kinds of motion a rigid body can have, and what is special about pure rotation.

  • Torque (moment of a force) as r × F: magnitude, direction and units.

  • What a couple is and why its torque is the same about every point.

  • The two conditions for equilibrium of a rigid body.

  • The principle of moments, the three classes of levers, and beam and ladder problems.

2.1 Rigid bodies and rotation

A rigid body is one in which the distance between any two particles never changes. Real bodies bend a little, but a cricket bat, a ceiling fan blade or a wheel behaves as rigid in most problems.

A rigid body can move in three ways:

MotionWhat happensEveryday example
Pure translationEvery particle has the same velocity at each instantA box sliding down a ramp
Pure rotation about a fixed axisEvery particle moves in a circle centred on the axisA ceiling fan, a potter's wheel
Rotation plus translationThe body turns while its COM movesA rolling cycle wheel, a spinning cricket ball

In rotation about a fixed axis, particles at different distances move with different speeds. But they all turn through the same angle in the same time. So every particle shares the same angular displacement θ, angular velocity ω = dθ/dt and angular acceleration α = dω/dt. A particle at distance r from the axis has speed v = rω and tangential acceleration a_t = rα.

2.2 Torque: the moment of a force

Push a door at the handle and it swings easily. Push near the hinges with the same force and it hardly moves. The turning effect depends on the force and on where and how it acts.

Let a force F act at a point whose position vector from the axis point O is r. The torque about O is

τ⃗=r⃗×F⃗,∣τ⃗∣=rFsin⁡θ\vec{\tau} = \vec{r} \times \vec{F}, \qquad |\vec{\tau}| = rF\sin\theta

Here θ is the angle between r and F. Two readings of rF sin θ help:

  • r sin θ is the perpendicular distance from O to the line of action of F. This is the moment arm r⊥. So τ = F × r⊥.

  • F sin θ is the component of F perpendicular to r. Only this part turns the body. So τ = r × F⊥.

Figure 2.1 · Torque of a force F acting at P about an axis through O
Figure 2.1 · Torque of a force F acting at P about an axis through O

Only the perpendicular distance r⊥ from O to the line of action of F sets the turning effect; pushing F along r gives no torque.

The direction of torque is perpendicular to both r and F, given by the right-hand rule. Curl the fingers of your right hand from r toward F; your thumb points along τ. Torque along +z means anticlockwise rotation as seen from above the xy-plane.

Torque is zero in three cases: F = 0, r = 0 (force acts at the axis point), or θ = 0° or 180° (line of action passes through O). A force parallel to the axis also gives zero turning about that axis.

The SI unit is N m, with dimensions [ML²T⁻²]. These are the same dimensions as work, but torque is never written in joules, because it is a vector and not an energy.

In component form, use the determinant:

τ⃗=∣i^j^k^xyzFxFyFz∣=(yFz−zFy)i^+(zFx−xFz)j^+(xFy−yFx)k^\vec{\tau} = \begin{vmatrix} \hat{i} & \hat{j} & \hat{k} \\ x & y & z \\ F_x & F_y & F_z \end{vmatrix} = (yF_z - zF_y)\hat{i} + (zF_x - xF_z)\hat{j} + (xF_y - yF_x)\hat{k}

Torque depends on the point you take it about. The same force has a different torque about a different point, so always name the point.

2.3 Couple

A couple is a pair of equal and opposite forces whose lines of action are parallel but separated. Turning a steering wheel with both hands, twisting a tap, or winding a wall clock key all use couples.

The net force of a couple is zero, so it produces no translation. Its torque is

τcouple=F×d\tau_{couple} = F \times d

where d is the perpendicular distance between the two lines of action. This torque is the same about every point in space. That is because the net force is zero, so shifting the reference point adds nothing.

A single force applied off the COM of a free body both pushes and turns it. A couple only turns it.

2.4 Conditions for equilibrium of a rigid body

A rigid body is in mechanical equilibrium when its linear momentum and its angular momentum both stay constant. That needs two conditions:

∑F⃗ext=0(translational equilibrium)\sum \vec{F}_{ext} = 0 \quad \text{(translational equilibrium)}
∑τ⃗ext=0(rotational equilibrium)\sum \vec{\tau}_{ext} = 0 \quad \text{(rotational equilibrium)}

When the net force is zero, the net torque is the same about every point. So if it is zero about one point, it is zero about all. This gives you freedom: take torques about the point where the most unknown forces act. Their torques vanish and the equation becomes easy.

A body can satisfy one condition and fail the other. A couple gives zero net force but non-zero torque. A force through the COM of a free body gives torque about the COM equal to zero but non-zero net force.

For problems in a plane, the vector conditions become three scalar equations: ΣF_x = 0, ΣF_y = 0, Στ = 0.

2.5 Principle of moments and levers

For a body in rotational equilibrium about a pivot, anticlockwise moments balance clockwise moments:

load×load arm=effort×effort arm\text{load} \times \text{load arm} = \text{effort} \times \text{effort arm}

A lever is a rigid bar that turns about a fixed point called the fulcrum. Its mechanical advantage is MA = load/effort = effort arm/load arm.

ClassWhat lies in the middleMechanical advantageExamples
FirstFulcrumGreater than, equal to or less than 1See-saw, scissors, hand pump of a village well
SecondLoadAlways greater than 1Nutcracker, wheelbarrow, bottle opener
ThirdEffortAlways less than 1Kitchen tongs, human forearm, cricket bat swing

A third-class lever needs more effort than the load. It is still useful because the load end moves farther and faster than the effort end.

2.6 Beams, rods and ladders

Most NEET equilibrium problems use a straight beam or a ladder. A reliable method:

  1. Draw every external force: weights at COMs, normal reactions, friction, tensions, hinge forces.

  2. Write ΣF_x = 0 and ΣF_y = 0.

  3. Take torques about the point with the most unknown forces.

  4. Solve, and check the signs make sense.

For a uniform ladder of length L against a smooth wall on rough ground, making angle θ with the ground, the wall pushes horizontally (no friction there). Ground friction must balance the wall's push. Taking torques about the foot gives the minimum coefficient of friction for no slipping:

μmin=12cot⁡θ\mu_{min} = \frac{1}{2}\cot\theta

The flatter the ladder, the larger μ must be. This is why a ladder placed too far from the wall slips.

Figure 2.2 · Forces on a uniform ladder against a smooth wall
Figure 2.2 · Forces on a uniform ladder against a smooth wall

The wall can only push horizontally, so ground friction f must equal N_w; taking torques about the foot removes both N and f from the equation.

Worked example 2.1: A mechanic applies 20 N at the end of a 25 cm spanner, at 30° to the handle. Find the torque on the nut.

Solution: τ = rF sin θ = 0.25 × 20 × sin 30° = 0.25 × 20 × 0.5 = 2.5 N m.

Worked example 2.2: A force F = (î − 2ĵ + 2k̂) N acts at the point r = (2î + 3ĵ − k̂) m. Find the torque about the origin and its magnitude.

Solution: Using the determinant: τ_x = (3)(2) − (−1)(−2) = 4. τ_y = (−1)(1) − (2)(2) = −5. τ_z = (2)(−2) − (3)(1) = −7. So τ = (4î − 5ĵ − 7k̂) N m. Magnitude = √(16 + 25 + 49) = √90 ≈ 9.49 N m.

Worked example 2.3: A driver turns a steering wheel of diameter 40 cm by pushing tangentially with 15 N on opposite ends of a diameter. Find the torque.

Solution: The two forces form a couple with arm d = 0.40 m. τ = F × d = 15 × 0.40 = 6 N m.

Worked example 2.4: A 30 kg child sits 2 m from the pivot of a see-saw. Where must a 40 kg child sit to balance it?

Solution: Moments balance: 30g × 2 = 40g × x. So x = 60/40 = 1.5 m from the pivot, on the other side.

Worked example 2.5: A metre rule pivoted at the 40 cm mark balances when a 30 g mass hangs at the 10 cm mark. Find the mass of the rule.

Solution: The rule is uniform, so its weight acts at the 50 cm mark, 10 cm right of the pivot. The 30 g mass is 30 cm left. Moments: 30 × 30 = M × 10. So M = 90 g.

Worked example 2.6: A uniform beam AB, 4 m long and weighing 200 N, rests on supports at A and B. A 600 N load hangs 1 m from A. Find the support reactions.

Solution: Torques about A: R_B × 4 = 200 × 2 + 600 × 1 = 1000. So R_B = 250 N. Vertical balance: R_A + R_B = 800, so R_A = 550 N. The support nearer the load carries more, as it should.

Worked example 2.7: A uniform 5 m ladder weighing 300 N leans against a smooth wall. Its foot is 3 m from the wall on rough ground. Find the friction at the foot and the least μ that prevents slipping.

Solution: The top is √(25 − 9) = 4 m high. Ground normal N = 300 N (vertical balance). Take torques about the foot. The weight acts 1.5 m out horizontally; the wall force N_w acts 4 m up. So N_w × 4 = 300 × 1.5, giving N_w = 112.5 N. Horizontal balance: friction f = N_w = 112.5 N. Least μ = 112.5/300 = 0.375. Check: (1/2) cot θ = (1/2)(3/4) = 0.375.

Worked example 2.8: A uniform 2 m rod weighing 50 N is hinged to a wall at one end A. A string from the other end B to a point on the wall holds it horizontal, making 30° with the rod. Find the tension and the hinge force.

Solution: Torques about A remove the unknown hinge force. Only the vertical part of T turns the rod: T sin 30° × 2 = 50 × 1. So T = 50 N. Hinge force: horizontal part = T cos 30° = 43.3 N (pushing out from the wall). Vertical part = 50 − T sin 30° = 25 N upward. Magnitude = √(43.3² + 25²) = 50 N.

Quick revision

  • τ = r × F, |τ| = rF sin θ = F × (perpendicular distance). Unit N m, dimensions [ML²T⁻²].

  • Torque is zero when the line of action passes through the axis or is parallel to it.

  • Couple: net force zero, torque Fd, same about every point.

  • Equilibrium: ΣF = 0 and Στ = 0 (about any one point).

  • Take torques about the point where the most unknowns act.

  • Levers: class II always MA > 1, class III always MA < 1.

  • Ladder on smooth wall, rough ground: μ_min = (1/2) cot θ.

NEET traps

  • Using the full length of the rod as the moment arm when the force is at an angle. Only r sin θ counts.

  • Giving the torque unit as J. Torque is in N m.

  • Forgetting the weight of the beam or rule itself, or placing it anywhere except its midpoint.

  • Taking cos θ instead of sin θ when θ is given with the rod rather than with the perpendicular.

  • Assuming a body with zero net force is in equilibrium. A couple can still spin it.

  • Mixing up the order in r × F. F × r gives the opposite sign.

Practice MCQs: Chapter 2

Level 1: Concept check

1. The SI unit of torque is (a) N m (b) N/m (c) N m² (d) kg m/s

2. The dimensional formula of torque is (a) [MLT⁻²] (b) [ML²T⁻¹] (c) [ML²T⁻²] (d) [ML⁻¹T⁻²]

3. The torque of a force about an axis is zero when the force (a) acts at the farthest point from the axis (b) is perpendicular to the position vector (c) is very large (d) has its line of action through the axis

4. For a couple acting on a free rigid body, (a) net force is zero, net torque is non-zero (b) both are zero (c) net force is non-zero, torque is zero (d) both are non-zero

5. Door handles are fixed far from the hinges because (a) it looks better (b) a larger moment arm gives a larger torque for the same force (c) it reduces the door's mass (d) it reduces friction at the hinges

6. A 10 N force acts at 0.5 m from an axis, perpendicular to the position vector. The torque is (a) 20 N m (b) 0.05 N m (c) 10 N m (d) 5 N m

7. A rigid body is in mechanical equilibrium when (a) only ΣF = 0 (b) only Στ = 0 (c) both ΣF = 0 and Στ = 0 (d) ΣF = 0 and the body is at rest

8. A nutcracker is a lever of the (a) first class (b) third class (c) not a lever at all (d) second class

9. A position vector points along +x and a force along +y. The torque points along (a) +x (b) −z (c) +y (d) +z

10. The mechanical advantage of a third-class lever is (a) greater than 1 (b) less than 1 (c) always exactly 1 (d) infinite

Level 2: NEET standard

11. A force (2î − 3ĵ) N acts at the point (î + ĵ) m. The torque about the origin is (a) 5k̂ N m (b) k̂ N m (c) −k̂ N m (d) −5k̂ N m

12. A 50 N force acts at the end of a 0.4 m wrench at 60° to the handle. The torque is about (a) 17.3 N m (b) 10 N m (c) 20 N m (d) 34.6 N m

13. A uniform 6 m beam weighing 300 N rests on supports at its ends A and B. A 900 N load sits 2 m from A. The reaction at A is (a) 450 N (b) 600 N (c) 1200 N (d) 750 N

14. A metre rule pivoted at the 30 cm mark balances when a 60 g mass hangs at the 0 cm mark. The mass of the rule is (a) 60 g (b) 90 g (c) 45 g (d) 120 g

15. A uniform 10 m ladder weighing 400 N leans on a smooth wall with its foot 6 m from the wall. The friction at the foot is (a) 100 N (b) 150 N (c) 200 N (d) 300 N

16. A 4 N force along +y acts at the point (3 m, 0, 0). Its torque about the point (1 m, 0, 0) is (a) 12 N m along +z (b) 8 N m along −z (c) 8 N m along +z (d) 4 N m along +z

17. Two antiparallel forces of 8 N each have lines of action 25 cm apart. The torque of this couple is (a) 2 N m (b) 4 N m (c) 0.5 N m (d) zero

18. A uniform rod of weight W is hinged at one end and held horizontal by a vertical string at the other end. The tension is (a) W (b) W/2 (c) 2W (d) W/4

19. A 4 m see-saw is pivoted at its centre. A 25 kg child sits at one end. A 40 kg child balances it at a distance from the pivot of (a) 1.6 m (b) 2.0 m (c) 1.0 m (d) 1.25 m

20. A force (2î + 3ĵ) N acts at the point (4î + 6ĵ) m. Its torque about the origin is (a) 24k̂ N m (b) zero (c) 12k̂ N m (d) −12k̂ N m

21. A 20 N force acts at a point 0.3 m from an axis and gives a torque of 3 N m. The angle between the force and the position vector is (a) 30° (b) 45° (c) 60° (d) 90°

22. A forearm is held horizontal with a 2 kg ball in the hand, 32 cm from the elbow. The biceps pulls vertically 4 cm from the elbow. Ignoring the forearm's weight, the biceps force is (a) 80 N (b) 120 N (c) 160 N (d) 320 N

Level 3: Challenge

23. A uniform 3 m rod weighing 60 N is hinged to a wall and held horizontal by a string from its far end to the wall. The string makes 37° with the rod (sin 37° = 0.6). The tension is (a) 30 N (b) 50 N (c) 60 N (d) 100 N

24. In Q23, the magnitude of the hinge force is (a) 30 N (b) 40 N (c) 50 N (d) 70 N

25. A uniform ladder rests against a smooth wall at 60° to the rough ground. The least coefficient of friction that prevents slipping is about (a) 0.29 (b) 0.5 (c) 0.58 (d) 0.87

26. A uniform 4 m plank weighing 200 N rests on two supports: one at end A and one 3 m from A. A 400 N man walks past the second support. How far beyond it can he go before the plank tips? (a) 0.25 m (b) 0.5 m (c) 0.75 m (d) 1.0 m

27. A force (2î + ĵ − k̂) N acts at the point (î − ĵ + k̂) m. The magnitude of its torque about the origin is (a) 3 N m (b) 6 N m (c) √6 N m (d) 3√2 N m

28. A cube of side 0.4 m and weight 200 N rests on a rough floor that stops it sliding. A horizontal force is applied 0.3 m above the floor. The least force that starts to tip it is about (a) 150 N (b) 200 N (c) 133 N (d) 100 N

29. Assertion (A): The torque of a force about an axis is zero if the force is parallel to that axis. Reason (R): Torque about an axis is zero only when the line of action of the force passes through the axis. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: For a body in equilibrium, the net torque is zero about every point, not only about its COM. Statement II: A body with zero net force on it can still have an angular acceleration. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1aTorque = force × distance
2c[MLT⁻²][L]
3dMoment arm is zero
4aEqual, opposite forces cancel but have separated lines
5bτ = F × r⊥ grows with distance from hinge
6d10 × 0.5 = 5 N m
7cBoth translational and rotational equilibrium needed
8dLoad lies between fulcrum and effort
9dî × ĵ = k̂
10bEffort arm shorter than load arm
11dxF_y − yF_x = (1)(−3) − (1)(2) = −5
12a0.4 × 50 × sin 60° = 17.3 N m
13dR_B = (900 + 1800)/6 = 450 N; R_A = 1200 − 450
14b60 × 30 = M × 20
15bHeight 8 m; N_w × 8 = 400 × 3; f = N_w = 150 N
16cArm = 2 m along x, force +y: 8 N m along +z
17a8 × 0.25 = 2 N m
18bTorques about hinge: T × L = W × L/2
19d25 × 2 = 40 × x
20br is parallel to F (4/2 = 6/3)
21asin θ = 3/(0.3 × 20) = 0.5
22cF × 4 = 20 × 32
23bT × 0.6 × 3 = 60 × 1.5
24cHorizontal 40 N, vertical 30 N
25a(1/2) cot 60° = 1/(2√3) ≈ 0.29
26bTip about support: 200 × 1 = 400 × x
27dr × F = (0, 3, 3); magnitude 3√2
28cF × 0.3 = 200 × 0.2 gives 133 N
29cParallel forces also give zero torque about the axis
30aZero net force makes torque point-independent; a couple shows II

Chapter 2 revision sheet

One-page summary

  • A rigid body keeps the distance between any two of its particles fixed. Its motion is translation, rotation, or both.

  • Torque is the turning effect of a force: τ = r × F, magnitude τ = rF sin θ = F × (perpendicular distance of the line of action from the axis).

  • Torque is an axial vector. Its direction comes from the right-hand rule. Anticlockwise is usually taken positive.

  • SI unit of torque is N m. Its dimensions [ML²T⁻²] match work, but torque is a vector and is never written in joules.

  • Torque is zero when the force is zero, when the line of action passes through the axis, or when the force is parallel to the axis.

  • In components, τ = (yF_z − zF_y) î + (zF_x − xF_z) ĵ + (xF_y − yF_x) k̂.

  • A couple is two equal, opposite, non-collinear forces. Net force is zero; torque = F × d, the same about every point.

  • A couple cannot be balanced by a single force. Only another couple can balance it.

  • Translational equilibrium: ΣF = 0. Rotational equilibrium: Στ = 0 about any point.

  • When ΣF = 0, the torque sum is the same about every point, so take moments about the point with the most unknowns.

  • Principle of moments: load × load arm = effort × effort arm. Mechanical advantage MA = effort arm / load arm.

  • Lever classes: first (fulcrum in middle), second (load in middle, MA greater than 1), third (effort in middle, MA less than 1).

  • Ladder on a smooth wall and rough floor: wall reaction is horizontal, floor friction equals it, floor normal equals total weight; f = W/(2 tan θ) for a uniform ladder, θ with the floor.

  • A block pushed at height h tips before sliding when the toppling force is less than μmg.

Must-remember table

QuantityFormulaSI unitNote
Torqueτ = rF sin θN mzero when θ = 0° or 180°
Torque vectorτ = r × FN mright-hand rule
Coupleτ = F dN msame about every point
Translational equilibriumΣF = 0–COM has no acceleration
Rotational equilibriumΣτ = 0–about any point
Mechanical advantageeffort arm / load armnonegreater than 1 for second-class levers
Uniform ladder frictionf = W/(2 tan θ)Nsmooth wall, θ with floor
Tipping force (cube, top edge)F = mg/2Ncompare with μmg for sliding

Memory aids

  • "FLE 1-2-3": the middle item names the class. Fulcrum in middle = class 1, Load in middle = class 2, Effort in middle = class 3.

  • "Door handle far, hinge near": torque grows with the lever arm, which is why handles sit far from the hinge.

  • "Couple = Cannot be cancelled by one": a couple needs another couple to balance it.

  • "Pivot on the unknowns": take moments about the point where the most unknown forces act, so they drop out.

  • "Sin for spin": torque uses sin θ (cross product); work uses cos θ (dot product).

Concept connections

  • Cross products and vector components come from Physics Book 1: Physics and Measurement and Physics Book 2: Kinematics.

  • Free-body diagrams, friction and normal reactions in ladder and beam problems are from Physics Book 3: Laws of Motion.

  • Torque on a current loop and on a magnetic dipole (τ = m × B) returns in Physics Book 13: Magnetic Effects of Current and Magnetism; torque on an electric dipole (τ = p × E) in Physics Book 11: Electrostatics.

Practice MCQs: Chapter 2, Level 4 (new NEET pattern)

31. A 10 N force acts at a point 0.5 m from an axis. θ is the angle between the position vector r and the force F. Match List I with List II.

  • List I: A. θ = 90°; B. θ = 30°; C. θ = 0°; D. θ = 60°

  • List II: (i) 0; (ii) 2.5 N m; (iii) 5 N m; (iv) 4.33 N m

(a) A-iv, B-ii, C-i, D-iii (b) A-iii, B-ii, C-i, D-iv (c) A-iii, B-iv, C-i, D-ii (d) A-ii, B-iii, C-iv, D-i

32. Match each position vector r and force F (SI units) with the torque τ = r × F.

  • List I: A. r = 2î, F = 3ĵ; B. r = 2ĵ, F = 3î; C. r = 2î, F = 3î; D. r = 2k̂, F = 3î

  • List II: (i) 0; (ii) 6ĵ N m; (iii) −6k̂ N m; (iv) 6k̂ N m

(a) A-iii, B-iv, C-i, D-ii (b) A-iv, B-iii, C-ii, D-i (c) A-iv, B-ii, C-i, D-iii (d) A-iv, B-iii, C-i, D-ii

33. Match each lever with its mechanical advantage.

  • List I: A. First-class lever, effort arm 60 cm, load arm 20 cm; B. Second-class lever, load 20 cm and effort 80 cm from the fulcrum; C. Third-class lever, effort 5 cm and load 30 cm from the fulcrum; D. First-class lever with equal arms

  • List II: (i) 1; (ii) 3; (iii) 1/6; (iv) 4

(a) A-ii, B-iv, C-iii, D-i (b) A-iv, B-ii, C-iii, D-i (c) A-ii, B-iii, C-iv, D-i (d) A-i, B-iv, C-iii, D-ii

34. Match the force and torque condition with the motion it produces in a free rigid body.

  • List I: A. ΣF = 0 and Στ = 0; B. ΣF = 0 but Στ ≠ 0; C. ΣF ≠ 0, line of action through the COM; D. ΣF ≠ 0 and Στ about the COM ≠ 0

  • List II: (i) angular acceleration only, COM does not accelerate; (ii) both linear and angular acceleration; (iii) complete equilibrium; (iv) COM accelerates, no angular acceleration

(a) A-i, B-iii, C-iv, D-ii (b) A-iii, B-iv, C-i, D-ii (c) A-iii, B-i, C-ii, D-iv (d) A-iii, B-i, C-iv, D-ii

35. How many of the following statements about a couple are correct?

  • A. The net force of a couple is zero.

  • B. The torque of a couple is the same about every point.

  • C. A couple can be balanced by a single suitable force.

  • D. Torque of a couple = one force × perpendicular distance between the two lines of action.

  • E. A couple acting on a free body accelerates its centre of mass.

(a) 2 (b) 4 (c) 3 (d) 5

36. A uniform ladder rests against a smooth vertical wall with its foot on a rough floor. No one stands on it. Choose the correct set of statements.

  • A. The reaction of the wall on the ladder is horizontal.

  • B. The normal reaction of the floor equals the weight of the ladder.

  • C. The friction at the floor equals the wall reaction in magnitude.

  • D. The friction needed increases as the ladder is made steeper (larger angle with the floor).

(a) A, B and C only (b) A and D only (c) B, C and D only (d) A, B, C and D

37. How many of the following statements are correct?

  • A. Torque is an axial vector.

  • B. A force parallel to the axis of rotation gives zero torque about that axis.

  • C. A force whose line of action passes through the axis gives zero torque about it.

  • D. Torque and work are the same physical quantity because both are measured in N m.

  • E. The torque of a single force depends on the point about which it is taken.

(a) 4 (b) 3 (c) 2 (d) 5

38. A uniform 4 m beam weighing 200 N rests on supports at its two ends. A 400 N load sits 1 m from the left end. Choose the correct set of statements.

  • A. The left support pushes up with 400 N.

  • B. The right support pushes up with 300 N.

  • C. The two reactions add up to 600 N.

  • D. Moving the load towards the right support increases the left reaction.

(a) A, B and C only (b) B and D only (c) A and C only (d) C and D only

39. The table lists four forces acting on the same wheel, all at the rim plane.

ForceF (N)r (m)Angle between r and F
P200.390°
Q300.430°
R250.560°
S400.290°

The correct order of torque magnitudes is

(a) S > R > P > Q (b) R > S > P = Q (c) R > P > S > Q (d) P = Q > S > R

40. A graph of torque τ (y-axis) against the angle θ between r and F (x-axis, 0° to 180°) is a smooth hump. It starts at 0, peaks at 12 N m at θ = 90° and returns to 0 at 180°. The force is fixed at 8 N. The value of r and the torque at θ = 150° are

(a) 1.5 m, 6 N m (b) 1.5 m, 10.4 N m (c) 0.67 m, 6 N m (d) 1.2 m, 6 N m

41. A uniform metre rule balances on a knife edge at its 50 cm mark. A 30 g mass hangs at the 20 cm mark. Where must a 20 g mass hang to keep it balanced?

(a) 80 cm mark (b) 90 cm mark (c) 95 cm mark (d) 85 cm mark

Passage for Q42–43: A painter leans a uniform 5 m ladder of mass 20 kg against a smooth wall. Its foot rests on rough ground 3 m from the wall. Take g = 10 m/s². The ladder is just at rest.

42. The friction force at the foot of the ladder is

(a) 150 N (b) 100 N (c) 50 N (d) 75 N

43. The least coefficient of static friction between the ladder and the ground is

(a) 0.375 (b) 0.75 (c) 0.25 (d) 0.5

44. A uniform rod of length 2 m and mass 10 kg is hinged to a wall and held horizontal by a string tied to its far end. The string makes 30° with the rod. Take g = 10 m/s². The magnitude of the force exerted by the hinge on the rod is

(a) 50 N (b) 86.6 N (c) 100 N (d) 173 N

45. A 10 kg cube rests on a floor with μ = 0.6. A horizontal force F, slowly increased from zero, is applied at the middle of its top edge, perpendicular to a face. Take g = 10 m/s². What happens first?

(a) It slides when F reaches 60 N (b) It tips when F reaches 50 N (c) It tips when F reaches 100 N (d) It slides and tips together at 60 N

Level 4 answer key

QAnsReason
31bτ = 5 sin θ: 5, 2.5, 0, 4.33 N m
32dî×ĵ = k̂, ĵ×î = −k̂, î×î = 0, k̂×î = ĵ; each times 6
33aMA = effort arm/load arm: 60/20 = 3, 80/20 = 4, 5/30 = 1/6, 1
34dZero force and torque is equilibrium; a couple only spins; force through COM only translates; otherwise both
35cA, B, D true; a couple needs a couple to balance it and gives no COM acceleration
36aFriction f = W/(2 tan θ) falls as θ grows, so D is false
37aA, B, C, E true; torque is a vector, work a scalar
38cMoments about left end: 4R_R = 400 + 400, R_R = 200 N, R_L = 400 N; load moving right raises R_R
39bP = 6, Q = 30 × 0.4 × 0.5 = 6, R = 12.5 × 0.866 = 10.8, S = 8 N m
40arF = 12 so r = 1.5 m; 12 sin 150° = 6 N m
41c30 × 30 = 20 × x gives x = 45 cm right of the pivot
42dHeight 4 m; moments about foot: N_w × 4 = 200 × 1.5, N_w = 75 N = f
43aμ = f/N = 75/200 = 0.375
44cT sin 30° × 2 = 100 × 1 gives T = 100 N; hinge: 86.6 N horizontal, 50 N vertical, resultant 100 N
45bTipping about front edge: F × a = mg × a/2, F = 50 N, less than μmg = 60 N
28 min left
‹
›