Chapter 8 of 10 · 25 min read

Chapter 6: Heat Engines, Carnot Engine and Refrigerators

What you will learn

  • How a heat engine works, and how to find its efficiency.

  • How a refrigerator and a heat pump work, and how to find their coefficient of performance (COP).

  • The four steps of the Carnot cycle.

  • The full derivation of Carnot efficiency, η = 1 − T₂/T₁.

  • Carnot's theorem, and why it sets the upper limit for all engines.

  • How to solve NEET problems on changing source or sink temperatures, and engines in series.

6.1 Heat engines

A heat engine turns heat into work again and again, in a cycle. Every heat engine has three parts:

  1. A hot reservoir (source) at temperature T₁, such as burning fuel or a boiler.

  2. A working substance that goes through a cycle, such as air-fuel mixture in a car or steam in a power plant.

  3. A cold reservoir (sink) at temperature T₂, usually the atmosphere or a river.

Figure 6.1 · Heat engine: source, working substance and sink
Figure 6.1 · Heat engine: source, working substance and sink

Heat flows down from source to sink through the engine, and the engine taps part of that flow as work.

In each cycle the working substance takes heat Q₁ from the source, does work W, and rejects heat Q₂ to the sink. It returns to its starting state, so ΔU = 0 and:

W=Q1−Q2W = Q_1 - Q_2

The efficiency is the fraction of heat taken in that becomes work:

η=WQ1=1−Q2Q1\eta = \frac{W}{Q_1} = 1 - \frac{Q_2}{Q_1}

By the second law (Kelvin–Planck), Q₂ can never be zero, so η < 1 always.

A petrol car engine is an internal combustion engine: fuel burns inside the cylinder. A steam engine or a coal power station is an external combustion engine: fuel burns outside, in a boiler. Both follow the same rule. Real car engines reach only about 25–30% efficiency. The rest leaves through the exhaust and radiator.

6.2 Refrigerators and heat pumps

A refrigerator is a heat engine run backwards. It takes heat Q₂ from a cold body (the freezer), needs work W from outside (the compressor), and rejects heat Q₁ to a hot body (the kitchen air).

Figure 6.2 · Refrigerator: an engine run backwards
Figure 6.2 · Refrigerator: an engine run backwards

Every arrow is reversed compared with Figure 6.1: heat goes up from cold to hot, and work comes in from outside instead of going out.

Energy balance:

Q1=Q2+WQ_1 = Q_2 + W

That is why the back of a fridge feels warm: it gives out more heat than it removes from inside.

The working fluid (the refrigerant) goes through four steps: sudden expansion from high to low pressure, which cools it; taking heat from the cold inside; compression by the motor, which heats it; giving heat to the room through the coils at the back.

The coefficient of performance of a refrigerator is the heat removed per unit work:

β=Q2W=Q2Q1−Q2\beta = \frac{Q_2}{W} = \frac{Q_2}{Q_1 - Q_2}

Unlike efficiency, β is usually greater than 1. A window AC in a Delhi summer is a refrigerator that cools a room.

A heat pump uses the same machine to warm a room. What we want is Q₁, so:

βheat pump=Q1W=1+β\beta_{\text{heat pump}} = \frac{Q_1}{W} = 1 + \beta

6.3 The Carnot cycle

In 1824, Sadi Carnot asked: what is the best possible engine working between two fixed temperatures T₁ and T₂? His answer is a reversible engine, since any irreversibility wastes work. To exchange heat reversibly with each reservoir, the working substance must be at the reservoir's temperature, so those steps must be isothermal. To move between the two temperatures without any heat flow across a finite temperature difference, those steps must be adiabatic.

So the Carnot cycle has four reversible steps, using an ideal gas:

Figure 6.3 · Carnot cycle on a P-V diagram, states 1 to 4
Figure 6.3 · Carnot cycle on a P-V diagram, states 1 to 4

Heat enters only on the upper isotherm (at T₁) and leaves only on the lower isotherm (at T₂); the two steeper adiabats carry the gas between the two temperatures with no heat flow.

StepProcessTemperatureHeatWork by gas
1 → 2Isothermal expansionT₁Q₁ absorbednRT₁ ln(V₂/V₁)
2 → 3Adiabatic expansionT₁ to T₂0nR(T₁ − T₂)/(γ − 1)
3 → 4Isothermal compressionT₂Q₂ rejected−nRT₂ ln(V₃/V₄)
4 → 1Adiabatic compressionT₂ to T₁0−nR(T₁ − T₂)/(γ − 1)

The two adiabatic works cancel. The net work is the area enclosed by the loop.

6.4 Carnot efficiency: derivation

Step 1. Heat absorbed in the isothermal expansion 1 → 2 (ΔU = 0, so Q = W):

Q1=nRT1ln⁡V2V1Q_1 = nRT_1 \ln\frac{V_2}{V_1}

Step 2. Heat rejected in the isothermal compression 3 → 4:

Q2=nRT2ln⁡V3V4Q_2 = nRT_2 \ln\frac{V_3}{V_4}

Step 3. For the adiabatic steps, TV^(γ−1) = constant:

T1V2γ−1=T2V3γ−1,T1V1γ−1=T2V4γ−1T_1 V_2^{\gamma-1} = T_2 V_3^{\gamma-1}, \qquad T_1 V_1^{\gamma-1} = T_2 V_4^{\gamma-1}

Step 4. Divide the first by the second: (V₂/V₁)^(γ−1) = (V₃/V₄)^(γ−1). So V₂/V₁ = V₃/V₄, and the log terms in Steps 1 and 2 are equal.

Step 5. Therefore:

Q2Q1=T2T1⇒ηCarnot=1−T2T1\frac{Q_2}{Q_1} = \frac{T_2}{T_1} \quad\Rightarrow\quad \eta_{\text{Carnot}} = 1 - \frac{T_2}{T_1}

Points to remember:

  • η depends only on T₁ and T₂, both in kelvin.

  • η = 1 only if T₂ = 0 K, which cannot be reached. So even a Carnot engine is less than 100% efficient.

  • If T₁ = T₂, η = 0. You cannot get work from a single reservoir.

6.5 Carnot's theorem

  1. No engine working between two given temperatures can be more efficient than a Carnot (reversible) engine working between the same temperatures.

  2. All reversible engines working between the same two temperatures have the same efficiency, whatever the working substance.

So 1 − T₂/T₁ is the upper limit for every real engine. A claim of higher efficiency breaks the second law.

Which helps more? For a Carnot engine, lowering the sink by ΔT raises η more than raising the source by the same ΔT. This is because η depends on the ratio T₂/T₁, and a change in the smaller number T₂ changes the ratio more.

6.6 Carnot refrigerator

Run the Carnot cycle backwards. With Q₂/Q₁ = T₂/T₁:

βCarnot=T2T1−T2\beta_{\text{Carnot}} = \frac{T_2}{T_1 - T_2}

The COP is large when the two temperatures are close. A freezer set very cold needs more work per joule removed.

Link between a Carnot engine and the same machine run as a refrigerator between the same reservoirs:

β=1−ηη\beta = \frac{1 - \eta}{\eta}

6.7 Engine and refrigerator compared

FeatureHeat engineRefrigeratorHeat pump
PurposeGet work from heatRemove heat from cold bodyGive heat to warm body
Heat taken fromHot source (Q₁)Cold body (Q₂)Cold outside (Q₂)
WorkDone by engineDone on deviceDone on device
Figure of meritη = W/Q₁β = Q₂/WQ₁/W
Carnot value1 − T₂/T₁T₂/(T₁ − T₂)T₁/(T₁ − T₂)
Range0 to less than 1Can exceed 1Always above 1

Worked example 6.1: An engine takes 1200 J of heat per cycle and rejects 900 J. Find the work per cycle and the efficiency.

Solution: W = Q₁ − Q₂ = 1200 − 900 = 300 J. η = W/Q₁ = 300/1200 = 0.25 = 25%.

Worked example 6.2: Find the efficiency of a Carnot engine working between 527 °C and 127 °C.

Solution: T₁ = 800 K, T₂ = 400 K. η = 1 − 400/800 = 0.5 = 50%. Using Celsius values would give 1 − 127/527 = 76%, which is wrong.

Worked example 6.3: A Carnot engine with its sink at 300 K has an efficiency of 40%. By how much must the source temperature be raised to make the efficiency 50%?

Solution: 0.4 = 1 − 300/T₁ gives T₁ = 500 K. For 50%, 0.5 = 1 − 300/T₁ gives T₁ = 600 K. The source must be raised by 100 K.

Worked example 6.4: A Carnot engine absorbs 2000 J per cycle from a source at 600 K. The sink is at 300 K. Find the work done and the heat rejected per cycle.

Solution: η = 1 − 300/600 = 0.5. W = ηQ₁ = 1000 J. Q₂ = Q₁ − W = 1000 J. Check: Q₂/Q₁ = T₂/T₁ = 0.5.

Worked example 6.5: A freezer is kept at −13 °C in a room at 27 °C. Find the Carnot COP. If it removes 1300 J of heat each second, find the least power needed.

Solution: T₂ = 260 K, T₁ = 300 K. β = 260/(300 − 260) = 6.5. W = Q₂/β = 1300/6.5 = 200 J each second, that is 200 W.

Worked example 6.6: A Carnot engine has efficiency 1/5. Find its COP when run as a refrigerator between the same reservoirs.

Solution: β = (1 − η)/η = (4/5)/(1/5) = 4. Check with temperatures: η = 1/5 means T₂/T₁ = 4/5, so β = T₂/(T₁ − T₂) = 4/(5 − 4) = 4.

Worked example 6.7: A 1-ton window AC removes 3.5 kW of heat from a room. Its actual COP is 3.5. Find the electrical power it uses and the heat it throws outside each second.

Solution: W = Q₂/β = 3.5/3.5 = 1.0 kW. Q₁ = Q₂ + W = 4.5 kW goes out to the street. That is why the air near an AC outdoor unit is so hot.

Worked example 6.8: A Carnot engine has efficiency 1/4. When its sink temperature is lowered by 75 K, keeping the source fixed, the efficiency becomes 1/2. Find the source and sink temperatures.

Solution: First: T₂/T₁ = 3/4. Second: (T₂ − 75)/T₁ = 1/2. Subtract: 75/T₁ = 3/4 − 1/2 = 1/4. So T₁ = 300 K and T₂ = 225 K.

Worked example 6.9: Two Carnot engines A and B run in series. A takes heat from a source at 800 K and gives its rejected heat to B at temperature T. B rejects heat to a sink at 200 K. Find T if (i) the two efficiencies are equal, (ii) the two works are equal.

Solution: (i) 1 − T/800 = 1 − 200/T gives T² = 800 × 200, so T = 400 K. (ii) W(A) = Q₁ − Q, W(B) = Q − Q₂, and each Q is proportional to its temperature. Equal works give 800 − T = T − 200, so T = 500 K.

Quick revision

  • Engine: W = Q₁ − Q₂, η = W/Q₁ = 1 − Q₂/Q₁ < 1.

  • Refrigerator: Q₁ = Q₂ + W, β = Q₂/W. Heat pump: Q₁/W = 1 + β.

  • Carnot cycle: isothermal expansion, adiabatic expansion, isothermal compression, adiabatic compression.

  • Carnot: Q₂/Q₁ = T₂/T₁, η = 1 − T₂/T₁, β = T₂/(T₁ − T₂). Kelvin only.

  • β = (1 − η)/η for the same reversible machine.

  • No engine beats Carnot; all reversible engines between the same temperatures are equally efficient.

  • Engines in series: equal η gives T = √(T₁T₂); equal work gives T = (T₁ + T₂)/2.

NEET traps

  • Using Celsius in 1 − T₂/T₁. Always convert to kelvin.

  • Writing COP as W/Q₂ or Q₁/W for a refrigerator. For a refrigerator it is Q₂/W.

  • Thinking COP must be less than 1, like efficiency.

  • Thinking the Carnot efficiency depends on the gas used.

  • Forgetting that the heat given out by a fridge (Q₁) is more than the heat it removes (Q₂).

  • Believing that a claim of efficiency higher than the Carnot value could be right with a better design. It breaks the second law.

Practice MCQs: Chapter 6

Level 1: Concept check

1. The efficiency of a heat engine is (a) W/Q₁ (b) Q₂/Q₁ (c) Q₁/W (d) W/Q₂

2. The efficiency of a Carnot engine depends on (a) the working substance (b) the source and sink temperatures only (c) the size of the engine (d) the speed of the engine

3. The Carnot cycle consists of (a) two isobaric and two isochoric steps (b) four isothermal steps (c) two isothermal and two adiabatic steps (d) two isochoric and two adiabatic steps

4. The coefficient of performance of a refrigerator is (a) Q₁/W (b) W/Q₂ (c) Q₂/Q₁ (d) Q₂/W

5. A Carnot engine works between 400 K and 300 K. Its efficiency is (a) 75% (b) 25% (c) 33% (d) 57%

6. The efficiency of a Carnot engine would be 100% if (a) T₁ = T₂ (b) T₁ = 2T₂ (c) the source were at 0 K (d) the sink were at 0 K

7. In a refrigerator, the heat given out to the surroundings is (a) Q₂ (b) W (c) Q₂ + W (d) Q₂ − W

8. For an ideal Carnot engine, the working substance (a) can be anything, as the efficiency does not depend on it (b) must be a monatomic gas (c) must be steam (d) must be a diatomic gas

9. No engine working between two given temperatures can be more efficient than a (a) diesel engine (b) petrol engine (c) Carnot engine (d) steam engine

10. The COP of a Carnot refrigerator working between T₂ (cold) and T₁ (hot) is (a) T₂/(T₁ − T₂) (b) T₁/(T₁ − T₂) (c) (T₁ − T₂)/T₁ (d) T₂/T₁

Level 2: NEET standard

11. An engine absorbs 1500 J per cycle and rejects 1050 J. Its efficiency is (a) 70% (b) 30% (c) 43% (d) 25%

12. A Carnot engine works between 227 °C and 27 °C. Its efficiency is (a) 88% (b) 60% (c) 40% (d) 12%

13. A Carnot engine has efficiency 50% and its sink is at 27 °C. The source temperature is (a) 54 °C (b) 600 °C (c) 300 °C (d) 327 °C

14. A Carnot refrigerator keeps its inside at −23 °C in a room at 27 °C. Its COP is (a) 5 (b) 6 (c) 0.2 (d) 1.2

15. A Carnot engine absorbs 1000 J per cycle from a source at 500 K. The sink is at 300 K. The work done per cycle is (a) 600 J (b) 400 J (c) 1000 J (d) 250 J

16. A Carnot engine has efficiency 25%. Run as a refrigerator between the same reservoirs, its COP is (a) 4 (b) 0.33 (c) 3 (d) 0.75

17. A refrigerator with COP 4 removes 800 J of heat from its inside. The heat it gives to the room is (a) 800 J (b) 200 J (c) 600 J (d) 1000 J

18. A Carnot engine with its sink at 300 K has efficiency 40%. To raise its efficiency to 50% with the same sink, the source temperature must be raised by (a) 100 K (b) 50 K (c) 150 K (d) 200 K

19. An air conditioner removes 3.5 kW of heat from a room and has a COP of 3.5. The electrical power it draws is (a) 3.5 kW (b) 12.25 kW (c) 1.0 kW (d) 0.29 kW

20. A Carnot heat pump warms a room at 27 °C using outside air at 7 °C. Its COP as a heat pump (Q₁/W) is (a) 14 (b) 15 (c) 1.07 (d) 0.067

21. Two Carnot engines run in series between 900 K and 100 K. Their efficiencies are equal. The intermediate temperature is (a) 500 K (b) 450 K (c) 400 K (d) 300 K

22. In Q21, if instead the two engines do equal work, the intermediate temperature is (a) 500 K (b) 300 K (c) 450 K (d) 400 K

Level 3: Challenge

23. A Carnot engine has efficiency 1/4. If the sink temperature is lowered by 80 K with the source fixed, the efficiency becomes 1/2. The source and sink temperatures are (a) 400 K and 300 K (b) 320 K and 240 K (c) 240 K and 180 K (d) 480 K and 360 K

24. A Carnot engine works between 500 K and 300 K. If the sink is lowered by 50 K with the source fixed, the new efficiency is (a) 45.5% (b) 40% (c) 50% (d) 55%

25. A Carnot engine working between 800 K and 300 K does 1000 J of work per cycle. The heat rejected per cycle is (a) 375 J (b) 1600 J (c) 1000 J (d) 600 J

26. A Carnot refrigerator works between −3 °C and 27 °C. The work needed to remove 900 J of heat from the cold side is (a) 100 J (b) 90 J (c) 1000 J (d) 81 J

27. An inventor claims an engine working between 127 °C and 27 °C with an efficiency of 30%. The claim is (a) possible (b) impossible, as the maximum is 25% (c) possible only with an ideal gas (d) impossible, as the maximum is 75%

28. A Carnot engine with its sink at 300 K has efficiency 40%. Keeping the source fixed, the sink is cooled to 240 K. The new efficiency is (a) 48% (b) 60% (c) 50% (d) 52%

29. Assertion (A): The coefficient of performance of a refrigerator can be greater than 1. Reason (R): COP is the ratio of heat removed from the cold body to the work done, and the heat removed can exceed the work. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: The efficiency of a Carnot engine depends on the working substance. Statement II: The efficiency of a Carnot engine increases if the sink temperature is lowered while the source temperature is fixed. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1aUseful work over heat taken in
2bη = 1 − T₂/T₁
3cTwo isotherms, two adiabats
4dHeat removed per unit work
5b1 − 300/400 = 0.25
6dT₂ = 0 K makes T₂/T₁ = 0
7cQ₁ = Q₂ + W
8aCarnot's theorem
9cCarnot's theorem
10aQ₂/(Q₁ − Q₂) with Q ∝ T
11bW = 450 J; 450/1500 = 0.30
12c1 − 300/500 = 0.40
13dT₁ = 300/0.5 = 600 K = 327 °C
14a250/(300 − 250) = 5
15bη = 0.4; W = 400 J
16c(1 − 0.25)/0.25 = 3
17dW = 800/4 = 200 J; Q₁ = 1000 J
18aT₁ goes from 500 K to 600 K
19c3.5/3.5 = 1.0 kW
20b300/(300 − 280) = 15
21d√(900 × 100) = 300 K
22a(900 + 100)/2 = 500 K
23b80/T₁ = 1/4 gives T₁ = 320 K, T₂ = 240 K
24c1 − 250/500 = 0.50
25dη = 5/8; Q₁ = 1600 J; Q₂ = 600 J
26aβ = 270/30 = 9; W = 900/9 = 100 J
27bCarnot limit 1 − 300/400 = 25%
28dT₁ = 500 K; 1 − 240/500 = 0.52
29aR explains why β can exceed 1
30dCarnot η is independent of the substance

Chapter 6 revision sheet

One-page summary

  • A heat engine takes Q₁ from a hot source, does work W, and rejects Q₂ to a cold sink, in a cycle.

  • W = Q₁ − Q₂ and efficiency η = W/Q₁ = 1 − Q₂/Q₁. By the second law η < 1.

  • Petrol and diesel engines burn fuel inside the cylinder (internal combustion). A steam engine burns fuel outside (external combustion).

  • A refrigerator takes Q₂ from the cold inside, uses work W, and rejects Q₁ = Q₂ + W to the room.

  • COP of a refrigerator β = Q₂/W = Q₂/(Q₁ − Q₂). It can be greater than 1.

  • Heat pump COP = Q₁/W = 1 + β.

  • Carnot cycle: isothermal expansion at T₁, adiabatic expansion to T₂, isothermal compression at T₂, adiabatic compression back to T₁.

  • For a Carnot engine Q₂/Q₁ = T₂/T₁, so η = 1 − T₂/T₁ (T in kelvin).

  • Carnot theorem: no engine between two reservoirs beats a reversible engine; all reversible engines between them have the same η, whatever the working substance.

  • η = 1 only if T₂ = 0 K, which cannot be reached.

  • Carnot refrigerator: β = T₂/(T₁ − T₂). Carnot heat pump: T₁/(T₁ − T₂).

  • Link between engine and fridge on the same reservoirs: β = (1 − η)/η.

  • Lowering T₂ by some amount raises η more than raising T₁ by the same amount.

  • Two Carnot engines in series (T₁ to T to T₃): equal efficiencies need T = √(T₁T₃); equal work needs T = (T₁ + T₃)/2.

  • Smaller temperature gap gives a bigger COP, so a fridge works harder on a hot day.

Must-remember table

DeviceMeasureGeneral formulaCarnot (ideal) value
Heat engineηW/Q₁ = 1 − Q₂/Q₁1 − T₂/T₁
RefrigeratorβQ₂/WT₂/(T₁ − T₂)
Heat pumpCOPQ₁/W = 1 + βT₁/(T₁ − T₂)
Engine and fridge, same T₁, T₂Linkβ = (1 − η)/η
Carnot heat ratioQ₂/Q₁T₂/T₁
Series engines, equal ηMiddle T√(T₁T₃)
Series engines, equal WMiddle T(T₁ + T₃)/2

Memory aids

  • "I-A-I-A, Expand then Compress": Carnot steps go Isothermal, Adiabatic, Isothermal, Adiabatic; first two expand, last two compress.

  • "Cold over Gap": Carnot fridge COP = T(cold)/(T gap).

  • "Hot over Gap for the Home heater": heat pump COP = T(hot)/(T gap).

  • "Kelvin or Kaput": always convert to kelvin before using T₂/T₁.

  • "Geometric for Gains equal, Arithmetic for Amount equal": series engines with equal η use the geometric mean, equal W uses the arithmetic mean.

Concept connections

  • Chemistry Book 4: Chemical Thermodynamics uses the same second-law ideas (entropy, spontaneity) to judge reactions.

  • Physics Book 9: Kinetic Theory of Gases supplies PV = nRT, used in deriving Q₂/Q₁ = T₂/T₁.

  • Physics Book 12: Current Electricity gives power P = W/t, used when a fridge or AC is rated in watts.

Practice MCQs: Chapter 6, Level 4 (new NEET pattern)

31. Match List I with List II.

List I:

  • A. Efficiency of any heat engine

  • B. Efficiency of a Carnot engine

  • C. COP of a Carnot refrigerator

  • D. COP of a Carnot heat pump

List II:

  • (i) T₁/(T₁ − T₂)

  • (ii) 1 − Q₂/Q₁

  • (iii) T₂/(T₁ − T₂)

  • (iv) 1 − T₂/T₁

(a) A-ii, B-iv, C-iii, D-i (b) A-iv, B-ii, C-iii, D-i (c) A-ii, B-iv, C-i, D-iii (d) A-ii, B-iii, C-iv, D-i

32. Reversible devices work between 500 K and 300 K. Match List I with List II.

List I:

  • A. Efficiency of the engine

  • B. COP of the refrigerator

  • C. COP of the heat pump

  • D. Ratio Q₂/Q₁ for the engine

List II:

  • (i) 1.5

  • (ii) 0.6

  • (iii) 2.5

  • (iv) 0.4

(a) A-ii, B-i, C-iii, D-iv (b) A-iv, B-iii, C-i, D-ii (c) A-iv, B-i, C-iii, D-ii (d) A-iv, B-ii, C-iii, D-i

33. Match each stage of the Carnot cycle with what happens to the gas.

List I:

  • A. Isothermal expansion at T₁

  • B. Adiabatic expansion

  • C. Isothermal compression at T₂

  • D. Adiabatic compression

List II:

  • (i) Rejects heat to the sink

  • (ii) Temperature rises with no heat exchange

  • (iii) Absorbs heat from the source

  • (iv) Temperature falls with no heat exchange

(a) A-iii, B-ii, C-i, D-iv (b) A-iii, B-iv, C-i, D-ii (c) A-i, B-iv, C-iii, D-ii (d) A-iv, B-iii, C-i, D-ii

34. Match List I with List II.

List I:

  • A. Source

  • B. Sink

  • C. Working substance

  • D. Cold reservoir of a household refrigerator

List II:

  • (i) The food compartment

  • (ii) Steam or gas that runs through the cycle

  • (iii) Reservoir at higher temperature that supplies heat

  • (iv) Reservoir at lower temperature that takes the rejected heat

(a) A-iv, B-iii, C-ii, D-i (b) A-iii, B-iv, C-i, D-ii (c) A-ii, B-iv, C-iii, D-i (d) A-iii, B-iv, C-ii, D-i

35. How many of the following statements are correct?

  • A. The efficiency of a Carnot engine depends only on the reservoir temperatures.

  • B. The efficiency of a Carnot engine depends on the working substance.

  • C. A Carnot engine would have efficiency 1 only if its sink were at 0 K.

  • D. The COP of a refrigerator can be greater than 1.

(a) One (b) Two (c) Three (d) Four

36. Choose the correct set of statements about Carnot devices.

  • A. Lowering T₂ by 10 K raises the efficiency more than raising T₁ by 10 K.

  • B. With the inside fixed, the COP of a Carnot refrigerator rises as the room gets hotter.

  • C. For an engine and a refrigerator on the same two reservoirs, β = (1 − η)/η.

  • D. The COP of a heat pump equals 1 + β.

(a) A, C and D only (b) A and B only (c) B, C and D only (d) C and D only

37. How many of the following statements are correct?

  • A. A real engine working between 500 K and 300 K can have an efficiency of 45%.

  • B. All reversible engines between the same two reservoirs have the same efficiency.

  • C. A petrol engine is an internal combustion engine.

  • D. A refrigerator rejects less heat to the room than it takes from the inside.

(a) One (b) Two (c) Three (d) Four

38. Choose the correct set of statements about refrigerators.

  • A. Heat rejected to the room = heat taken from inside + work input.

  • B. A Carnot freezer at 260 K in a room at 300 K has COP 6.5.

  • C. A fridge of COP 5 that removes 1000 J from inside needs 200 J of work.

  • D. The same fridge rejects 800 J to the room.

(a) A and D only (b) B and C only (c) A, B and D only (d) A, B and C only

39. For a Carnot engine with a fixed source temperature, efficiency η (y-axis) is plotted against sink temperature T₂ (x-axis). The graph is a straight line that meets η = 0 at T₂ = 600 K. The source temperature, and η when T₂ = 150 K, are: (a) 300 K and 0.50 (b) 600 K and 0.25 (c) 600 K and 0.75 (d) 750 K and 0.80

40. Three engines work between 400 K and 300 K. Each takes in 1000 J per cycle.

EngineWork per cycle (J)
E1200
E2250
E3300

Which statement is correct? (a) All three are possible (b) E1 is possible, E2 only if it is reversible, E3 is impossible (c) Only E3 is possible because it is most efficient (d) E2 and E3 are impossible

41. For a Carnot refrigerator with room temperature T₁ fixed, the COP is plotted against the inside temperature T₂ (from well below T₁ up towards T₁). The graph: (a) rises faster and faster, growing without limit as T₂ approaches T₁ (b) is a straight line with slope 1/T₁ (c) falls as T₂ rises (d) is constant

Case for Q42–43: On a Delhi summer afternoon the outside air is at 42 °C. An air conditioner keeps a room at 24 °C. It must remove 3.3 kW of heat from the room to hold that temperature. Treat it as an ideal Carnot refrigerator.

42. The ideal COP of the air conditioner is: (a) 1.3 (b) 0.57 (c) 17.5 (d) 16.5

43. The least electrical power the air conditioner needs is: (a) 3.3 kW (b) 200 W (c) 1.65 kW (d) 20 W

44. Two Carnot engines work in series. The first runs between 800 K and T, and the second between T and 200 K, using all the heat the first rejects. If both deliver the same work, T is: (a) 400 K (b) 600 K (c) 500 K (d) 300 K

45. A Carnot engine with its sink at 300 K has efficiency 40%. To raise the efficiency to 50% with the same sink, the source temperature must be raised by: (a) 100 K (b) 50 K (c) 60 K (d) 200 K

Level 4 answer key

QAnsReason
31aStandard engine, fridge and heat pump formulas
32cη = 0.4, β = 300/200, heat pump 500/200, Q₂/Q₁ = 300/500
33bHeat in at T₁, cools adiabatically, heat out at T₂, warms adiabatically
34dFridge takes heat from the food compartment
35cA, C, D true; Carnot η is independent of the gas
36aSmaller gap means bigger COP, so B is false
37bB and C true; max η = 40%; fridge rejects Q₂ + W
38dQ₁ = 1000 + 200 = 1200 J
39cη = 0 when T₂ = T₁ = 600 K; 1 − 150/600 = 0.75
40bCarnot limit is 25% = 250 J
41aβ = T₂/(T₁ − T₂) blows up as the gap shrinks
42d297/(315 − 297) = 297/18 = 16.5
43bW = 3300/16.5 = 200 W
44cEqual work: T₁ − T = T − T₃, so T = 500 K
45aT₁ = 300/0.6 = 500 K; new T₁ = 300/0.5 = 600 K
25 min left
‹
›