Last-Week Revision Kit
Use this kit in the final week: one pass through the tables, the facts and the checklist each day, and Mock Test 2 once under exam timing.
Book-at-a-glance sheet
Chapter 1: Conductors, Insulators and Semiconductors
| Item | Key formula or fact |
|---|---|
| Band gaps | Conductor 0 (overlap); Ge 0.7 eV; Si 1.1 eV; diamond about 5.4 eV; insulator above about 3 eV |
| Intrinsic | n_e = n_h = n_i; insulator at 0 K |
| n-type / p-type | Group 15 donor, electrons majority / group 13 acceptor, holes majority; both neutral |
| Mass action law | n_e n_h = n_i²; minority = n_i²/N |
| Conductivity | σ = e(n_e μ_e + n_h μ_h); ρ = 1/σ; ρ falls as T rises |
| Cut-off wavelength | λ_max (nm) = 1240/E_g (eV) |
Chapter 2: The p-n Junction
| Item | Key formula or fact |
|---|---|
| Depletion region | Immobile ions, no free carriers; field from n to p |
| Barrier | Si 0.7 V, Ge 0.3 V; forward V₀ − V, reverse V₀ + V |
| Currents | Diffusion by majority carriers; drift by minority carriers |
| Forward bias | Width narrows, mA current after knee |
| Reverse bias | Width grows, µA or nA current, rises with T; breakdown at high V |
| Dynamic resistance | r_d = ΔV/ΔI |
| Field | E ≈ V/d |
Chapter 3: Diode as a Rectifier
| Item | Half-wave | Full-wave (centre-tap / bridge) |
|---|---|---|
| Diodes | 1 | 2 / 4 |
| Output frequency | f | 2f |
| V_dc | V_m/π | 2V_m/π |
| V_rms | V_m/2 | V_m/√2 |
| PIV | V_m | 2V_m / V_m |
| Ripple factor, efficiency | 1.21, 40.6% | 0.48, 81.2% |
| Capacitor ripple | ΔV ≈ V_m/(f_r R_L C) | same, with f_r = 2f |
Chapter 4: Special Diodes: LED, Photodiode and Solar Cell
| Device | Bias, quadrant | Key formula or fact |
|---|---|---|
| Photodiode | Reverse, third | Photocurrent proportional to intensity; needs hν ≥ E_g |
| LED | Forward, first | λ = 1240/E_g; visible needs about 1.8–3.1 eV |
| Solar cell | None, fourth | FF = V_m I_m/(V_oc I_sc); η = P_max/P_in; best gap about 1.5 eV |
| Photon rate | — | N = P/E |
Chapter 5: Zener Diode and Voltage Regulation
| Item | Key formula or fact |
|---|---|
| Breakdown types | Zener: heavy doping, thin region, low V_z; avalanche: light doping, collisions |
| On check | V_in R_L/(R_s + R_L) greater than V_z |
| Currents | I_s = (V_in − V_z)/R_s; I_L = V_z/R_L; I_z = I_s − I_L |
| Power and limits | P_z = V_z I_z; I_z,max = P_z,max/V_z; R_s,min = (V_in,max − V_z)/I_z,max |
Chapter 6: Logic Gates
| Gate | Expression | Output for 00, 01, 10, 11 |
|---|---|---|
| OR | A + B | 0, 1, 1, 1 |
| AND | A·B | 0, 0, 0, 1 |
| NAND | NOT(A·B) | 1, 1, 1, 0 |
| NOR | NOT(A + B) | 1, 0, 0, 0 |
| NOT | Ā | 1 → 0, 0 → 1 |
| De Morgan | NOT(A + B) = Ā·B̄; NOT(A·B) = Ā + B̄ | — |
| NAND count | NOT 1, AND 2, OR 3, NOR 4 | — |
40 rapid-fire facts
A semiconductor's band gap is below about 3 eV; an insulator's is above it.
Silicon's band gap is about 1.1 eV and germanium's about 0.7 eV in this book's convention.
In a conductor the valence and conduction bands overlap.
Pure silicon behaves as an insulator at 0 K.
In an intrinsic semiconductor, n_e = n_h = n_i.
A hole acts as a positive charge +e and drifts along the field.
Phosphorus, arsenic and antimony are donors and make n-type silicon.
Boron, aluminium, gallium and indium are acceptors and make p-type silicon.
A donor level lies just below the conduction band; an acceptor level just above the valence band.
Both n-type and p-type crystals are electrically neutral.
The mass action law is n_e n_h = n_i² at a fixed temperature.
Electron mobility in silicon is larger than hole mobility.
A semiconductor's resistivity falls as temperature rises; a metal's rises.
The depletion region holds immobile ions and no free carriers.
The junction field points from the n side to the p side.
The barrier potential cannot be measured with a voltmeter.
Forward bias lowers the barrier and narrows the depletion region.
Reverse bias raises the barrier and widens the depletion region.
Forward current is mainly diffusion of majority carriers.
Reverse saturation current comes from minority carriers and rises with temperature.
A diode does not obey Ohm's law; its I-V curve is non-linear.
A half-wave rectifier's output has the same frequency as its input.
A full-wave rectifier's output has twice the input frequency.
A bridge rectifier uses four diodes, two conducting in each half cycle.
A centre-tap rectifier's diodes face a PIV of 2V_m.
The maximum efficiency of a half-wave rectifier is 40.6%; of a full-wave rectifier, 81.2%.
A capacitor filter is connected in parallel with the load.
A photodiode is operated in reverse bias.
Photocurrent is nearly proportional to light intensity.
An LED is operated in forward bias and emits photons of energy about E_g.
Silicon and germanium are not used for visible LEDs.
A solar cell needs no external bias and works in the fourth quadrant.
The ideal band gap for a solar cell is about 1.5 eV.
Solar cells in series add their voltages.
A Zener diode is heavily doped and works in reverse breakdown.
Zener breakdown happens in heavily doped diodes; avalanche breakdown in lightly doped ones.
In a regulator, I_s = I_z + I_L and the load voltage stays at V_z.
NAND and NOR are universal gates.
A NAND gate gives 0 only when all inputs are 1.
A NOR gate gives 1 only when all inputs are 0.
Common mistakes checklist
I don't say an n-type semiconductor is negatively charged; it is neutral.
I don't confuse the donor level (near the conduction band) with the acceptor level (near the valence band).
I can find the minority carrier density with n_i²/N without mixing up which carrier is majority.
I don't confuse diffusion current (majority carriers) with drift current (minority carriers).
I subtract 0.7 V per conducting silicon diode before using Ohm's law, unless the diode is ideal.
I don't confuse the output frequency of a half-wave rectifier (f) with a full-wave one (2f).
I can tell that centre-tap PIV is 2V_m while bridge PIV is V_m.
I don't put a photodiode in forward bias or an LED in reverse bias.
I check that the Zener is actually in breakdown before writing V_L = V_z.
I don't confuse NAND with NOR; I check the output codes 1110 and 1000.
Mock Test 2: New-pattern paper
Time: 35 minutes. 30 questions. +4 for a correct answer, −1 for a wrong one, 0 if left blank. Take hc = 1240 eV nm, e = 1.6 × 10⁻¹⁹ C and 0.7 V for a conducting silicon diode unless stated.
1. Germanium with n_i = 2.4 × 10¹⁹ m⁻³ is doped with acceptors to N_A = 4.8 × 10²¹ m⁻³. The electron density is about
(a) 1.2 × 10¹⁹ m⁻³ (b) 1.2 × 10¹⁷ m⁻³ (c) 2.4 × 10¹⁹ m⁻³ (d) 4.8 × 10²¹ m⁻³
2. How many of the following statements are correct?
A. A trivalent impurity creates an acceptor level just above the valence band.
B. In n-type silicon, holes are the minority carriers.
C. Pure silicon at room temperature has equal electron and hole densities.
D. Diamond conducts well at room temperature.
(a) one (b) two (c) three (d) four
3. Match List I with List II.
List I: A. Free electron in n-type Si · B. Hole in p-type Si · C. Ionised donor · D. Ionised acceptor
List II: i. immobile negative charge · ii. mobile positive majority carrier · iii. immobile positive charge · iv. mobile negative majority carrier
(a) A-iv, B-ii, C-iii, D-i (b) A-ii, B-iv, C-iii, D-i (c) A-iv, B-ii, C-i, D-iii (d) A-iii, B-ii, C-iv, D-i
4. Assertion (A): Doping silicon with arsenic increases its conductivity. Reason (R): Arsenic supplies extra holes to the valence band.
(a) Both A and R are true and R explains A (b) Both A and R are true but R does not explain A (c) A is true but R is false (d) A is false but R is true
5. The longest wavelength that can create electron-hole pairs in a material with E_g = 2.48 eV is
(a) 250 nm (b) 500 nm (c) 620 nm (d) 1000 nm
6. A silicon diode, forward biased, is in series with a 460 Ω resistor and a 3 V battery. The current is
(a) 5 mA (b) 6.5 mA (c) 4.3 mA (d) zero
7. A diode's reverse I-V graph shows the current fixed at about −1 µA from −1 V to −50 V, then rising steeply near −60 V. The graph shows that
(a) the diode obeys Ohm's law in reverse bias (b) breakdown occurs at −1 V (c) reverse current is proportional to reverse voltage (d) the saturation current is about 1 µA and breakdown is near 60 V
8. Choose the correct set of statements about a p-n junction.
A. In reverse bias, the depletion region widens.
B. In forward bias, the barrier height increases.
C. Diffusion current is carried by majority carriers.
D. At equilibrium, no carriers cross the junction at all.
(a) A and B only (b) A and C only (c) B and D only (d) A, C and D only
9. A 12 V battery is connected through a 4 Ω resistor to two parallel branches. Each branch has an 8 Ω resistor and an ideal diode. The diode in branch 1 is forward biased; the diode in branch 2 is reverse biased. The battery current is
(a) 1 A (b) 1.5 A (c) 3 A (d) 0.75 A
10. The forward voltage of a diode rises from 0.65 V to 0.70 V, and its current rises from 10 mA to 35 mA. The dynamic resistance is
(a) 20 Ω (b) 0.5 Ω (c) 2 Ω (d) 28 Ω
11. Match List I with List II.
List I: A. Bridge rectifier · B. Half-wave rectifier · C. Centre-tap rectifier · D. Capacitor filter
List II: i. PIV = 2V_m · ii. PIV = V_m, output at input frequency · iii. reduces ripple · iv. four diodes, PIV = V_m
(a) A-ii, B-iv, C-i, D-iii (b) A-iv, B-i, C-ii, D-iii (c) A-iv, B-ii, C-iii, D-i (d) A-iv, B-ii, C-i, D-iii
12. An ideal full-wave rectifier runs on a 60 Hz supply with V_m = 30 V. The dc output voltage and ripple frequency are
(a) 9.5 V, 60 Hz (b) 19.1 V, 120 Hz (c) 19.1 V, 60 Hz (d) 21.2 V, 120 Hz
13. How many of the following statements are correct?
A. A bridge rectifier needs no centre-tapped transformer.
B. The maximum efficiency of a half-wave rectifier is 40.6%.
C. The ripple factor of a full-wave rectifier is 0.48.
D. A capacitor filter makes the output exactly constant.
(a) one (b) two (c) three (d) four
Case for Q14–15. A hostel lamp supply uses 230 V rms, 50 Hz mains and a centre-tap full-wave rectifier with ideal diodes. Each half of the secondary gives 12 V rms.
14. The peak inverse voltage across each diode is about
(a) 33.9 V (b) 17.0 V (c) 24 V (d) 12 V
15. The dc output voltage is about
(a) 5.4 V (b) 12 V (c) 17.0 V (d) 10.8 V
16. Match the wavelength (List I) with the photon energy (List II).
List I: A. 413 nm · B. 827 nm · C. 564 nm · D. 1127 nm
List II: i. 1.1 eV · ii. 2.2 eV · iii. 3.0 eV · iv. 1.5 eV
(a) A-iv, B-iii, C-ii, D-i (b) A-iii, B-ii, C-iv, D-i (c) A-iii, B-iv, C-ii, D-i (d) A-i, B-iv, C-ii, D-iii
17. Assertion (A): The I-V curve of a solar cell is drawn in the fourth quadrant. Reason (R): A solar cell delivers power, so its current flows opposite to the forward-diode direction while its voltage is positive.
(a) Both A and R are true and R explains A (b) Both A and R are true but R does not explain A (c) A is true but R is false (d) A is false but R is true
18. An LED gives 1 mW of light with photon energy 2.5 eV. The number of photons emitted per second is
(a) 4.0 × 10¹⁵ (b) 2.5 × 10¹⁶ (c) 6.25 × 10¹⁵ (d) 2.5 × 10¹⁵
19. A solar cell's I-V graph shows V_oc = 0.55 V and I_sc = 2 A. If the light intensity is doubled, the new graph would show
(a) I_sc = 2 A, V_oc = 1.1 V (b) both I_sc and V_oc doubled (c) I_sc about 4 A, V_oc only slightly higher (d) I_sc halved
20. Choose the correct set of statements.
A. A photodiode's reverse current depends on light intensity.
B. The colour of an LED is set mainly by its band gap.
C. Solar cells are reverse biased by a battery.
D. A photodiode responds to photons with energy below its band gap.
(a) A, B and C only (b) A and B only (c) B and D only (d) A, B, C and D
21. An 8 V Zener regulator has V_in = 20 V, R_s = 400 Ω and R_L = 1 kΩ. The Zener current is
(a) 30 mA (b) 8 mA (c) 38 mA (d) 22 mA
22. A 10 V Zener regulator has V_in = 15 V and R_s = 100 Ω. It is tried with three loads.
| R_L (Ω) | 500 | 250 | 100 |
|---|
The load for which the Zener stops regulating is
(a) 100 Ω (b) 250 Ω (c) 500 Ω (d) none of them
23. Assertion (A): In avalanche breakdown, fast carriers break bonds by collision and multiply. Reason (R): Avalanche breakdown occurs in heavily doped junctions.
(a) Both A and R are true and R explains A (b) Both A and R are true but R does not explain A (c) A is true but R is false (d) A is false but R is true
24. How many of the following statements are correct?
A. The breakdown voltage of a Zener diode is set by its doping.
B. A regulator keeps V_L at V_z while I_z stays between its minimum and maximum values.
C. The series resistor of a regulator can be removed safely.
D. Zener power equals V_in × I_z.
(a) one (b) two (c) three (d) four
25. Match each expression (List I) with the gate it represents (List II).
List I: A. NOT(Ā·B̄) · B. NOT(Ā + B̄) · C. Ā·B̄ · D. Ā + B̄
List II: i. AND · ii. NAND · iii. OR · iv. NOR
(a) A-iii, B-i, C-iv, D-ii (b) A-i, B-iii, C-iv, D-ii (c) A-iii, B-i, C-ii, D-iv (d) A-iv, B-i, C-iii, D-ii
26. Over four intervals the inputs are A = 1, 0, 1, 0 and B = 1, 1, 0, 0. The output is Y = 0, 0, 0, 1. The gate is
(a) AND (b) NAND (c) OR (d) NOR
27. A and B feed an AND gate. Its output and A feed a NOR gate, whose output is Y. Then Y equals
(a) A (b) Ā (c) A·B (d) NOT(A·B)
28. Choose the correct set of statements.
A. A two-input NOR gate gives 1 for exactly one input combination.
B. A NOT gate can be made from one NOR gate.
C. The OR gate is a universal gate.
D. A·Ā = 1
(a) A, B and C only (b) B and D only (c) A and B only (d) A and D only
29. A red LED needs 2.0 V across it and should carry 14 mA from a 9 V battery. The series resistor needed is
(a) 500 Ω (b) 643 Ω (c) 143 Ω (d) 786 Ω
30. A factory conveyor has two photodiode sensors. Each gives logic 1 when light falls on it. An alarm must ring (Y = 1) only when neither sensor is lit. The gate to use is
(a) AND (b) OR (c) NAND (d) NOR
Mock Test 2 answer key
| Q | Ans | Reason |
|---|---|---|
| 1 | b | n_e = n_i²/N_A = 5.76 × 10³⁸/4.8 × 10²¹ = 1.2 × 10¹⁷ m⁻³ |
| 2 | c | A, B, C true; diamond's 5.4 eV gap makes it an insulator |
| 3 | a | Free carriers are mobile; ionised donors are fixed + and acceptors fixed − |
| 4 | c | Arsenic is a donor; it supplies electrons, not holes |
| 5 | b | λ = 1240/2.48 = 500 nm |
| 6 | a | (3 − 0.7)/460 = 5 mA |
| 7 | d | Flat reverse current is saturation current; the steep rise marks breakdown |
| 8 | b | Forward bias lowers the barrier (B false); carriers cross both ways in balance (D false) |
| 9 | a | Only branch 1 conducts: 12/(4 + 8) = 1 A; (b) assumes both conduct |
| 10 | c | r_d = 0.05 V/0.025 A = 2 Ω |
| 11 | d | Bridge four diodes with PIV V_m; half-wave PIV V_m at f; centre-tap 2V_m; filter cuts ripple |
| 12 | b | V_dc = 2 × 30/π ≈ 19.1 V; ripple at 2 × 60 = 120 Hz |
| 13 | c | A, B, C true; some ripple always remains (D false) |
| 14 | a | V_m = 12√2 ≈ 17.0 V; PIV = 2V_m ≈ 33.9 V |
| 15 | d | V_dc = 2V_m/π = 2 × 17.0/π ≈ 10.8 V |
| 16 | c | 1240/413 ≈ 3.0, 1240/827 ≈ 1.5, 1240/564 ≈ 2.2, 1240/1127 ≈ 1.1 eV |
| 17 | a | Positive V with current out of the cell (negative in diode convention) puts the curve in the fourth quadrant |
| 18 | d | N = 10⁻³/(2.5 × 1.6 × 10⁻¹⁹) = 2.5 × 10¹⁵ s⁻¹ |
| 19 | c | I_sc is proportional to intensity; V_oc grows only slowly |
| 20 | b | Solar cells need no bias (C false); photons below E_g make no pairs (D false) |
| 21 | d | Check: 20 × 1000/1400 ≈ 14.3 V > 8 V. I_s = 12/400 = 30 mA; I_L = 8 mA; I_z = 22 mA |
| 22 | a | With 100 Ω: 15 × 100/200 = 7.5 V < 10 V, so the Zener is off; the others give 12.5 V and 10.7 V |
| 23 | c | Avalanche breakdown happens in lightly doped junctions (R false) |
| 24 | b | A and B true; without R_s the Zener current is unlimited (C false); P_z = V_z I_z (D false) |
| 25 | a | By De Morgan: NOT(Ā·B̄) = A + B; NOT(Ā + B̄) = A·B; Ā·B̄ = NOT(A + B); Ā + B̄ = NOT(A·B) |
| 26 | d | A + B = 1, 1, 1, 0; complement 0, 0, 0, 1 is NOR |
| 27 | b | Y = NOT(A·B + A) = NOT(A) by absorption |
| 28 | c | NOR is 1 only for 00; joined-input NOR is NOT; OR is not universal; A·Ā = 0 |
| 29 | a | R = (9 − 2.0)/0.014 = 500 Ω |
| 30 | d | Y = 1 only when both inputs are 0: that is NOR |