Unit Test: Electronic Devices
Time: 50 minutes. Marking: +4 for a correct answer, −1 for a wrong answer, 0 if left blank. Use hc ≈ 1240 eV nm and e = 1.6 × 10⁻¹⁹ C. Take diodes as ideal unless a forward drop is given.
1. Germanium has n_i = 2.4 × 10¹⁹ m⁻³. It is doped with acceptors at 4.8 × 10²³ m⁻³. The electron concentration is (a) 2.4 × 10¹⁹ m⁻³ (b) 1.2 × 10¹⁵ m⁻³ (c) 4.8 × 10²³ m⁻³ (d) 5 × 10⁴ m⁻³
2. Light of wavelength 1500 nm can create electron-hole pairs in (E_g: Si 1.1 eV, Ge 0.7 eV) (a) Si only (b) both Si and Ge (c) Ge only (d) neither
3. Which dopant makes silicon n-type? (a) Antimony (b) Gallium (c) Boron (d) Indium
4. An intrinsic sample has n_i = 1.6 × 10¹⁶ m⁻³, μ_e = 0.14 and μ_h = 0.05 m² V⁻¹ s⁻¹. Its conductivity is about (a) 2.2 × 10⁻⁴ S m⁻¹ (b) 4.9 × 10⁻² S m⁻¹ (c) 3.6 × 10⁻⁴ S m⁻¹ (d) 4.9 × 10⁻⁴ S m⁻¹
5. A junction has barrier potential 0.5 V across a depletion layer 0.25 μm wide. The average field is (a) 1.25 × 10⁵ V m⁻¹ (b) 2 × 10⁶ V m⁻¹ (c) 5 × 10⁵ V m⁻¹ (d) 2 × 10⁵ V m⁻¹
6. A diode carries 10 mA at 0.72 V and 30 mA at 0.76 V. Its dynamic resistance is (a) 2 Ω (b) 0.5 Ω (c) 25 Ω (d) 72 Ω
7. A silicon diode (0.7 V) is forward biased by 6 V through 265 Ω. The current is (a) 22.6 mA (b) 2.6 mA (c) 20 mA (d) 17.4 mA
8. Below breakdown, the reverse saturation current of a diode depends mainly on (a) the reverse voltage (b) the series resistance (c) the size of the battery (d) the temperature
9. 230 V rms mains feeds a 23 : 1 step-down transformer and a half-wave rectifier. The dc output is about (a) 10 V (b) 4.5 V (c) 14.1 V (d) 9.0 V
10. The input to a full-wave rectifier is v = 50 sin(120πt) volt. The output frequency is (a) 60 Hz (b) 30 Hz (c) 120 Hz (d) 240 Hz
11. In a centre-tap rectifier, each half of the secondary gives 15 V rms. The peak inverse voltage on each diode is about (a) 42.4 V (b) 21.2 V (c) 30 V (d) 15 V
12. An LED material has E_g = 2.1 eV. The emitted wavelength is about (a) 480 nm (b) 650 nm (c) 2600 nm (d) 590 nm
13. A photodiode is operated in reverse bias because (a) light cannot enter in forward bias (b) it has no forward current (c) the photocurrent is then a large fraction of the total current (d) the band gap is reduced in reverse bias
14. A solar cell has V_oc = 0.62 V, I_sc = 4 A and fill factor 0.7. Its maximum power is about (a) 2.48 W (b) 1.74 W (c) 1.24 W (d) 3.54 W
15. A regulator has V_in = 20 V, V_z = 12 V, R_s = 200 Ω and R_L = 1.2 kΩ. The Zener current is (a) 30 mA (b) 40 mA (c) 10 mA (d) 50 mA
16. A 9 V Zener is used with V_in = 12 V, R_s = 2 kΩ and R_L = 4 kΩ. The load voltage is (a) 9 V (b) 12 V (c) 3 V (d) 8 V
17. A gate gives outputs 0, 0, 0, 1 for inputs (A, B) = 00, 01, 10, 11. It is (a) OR (b) NAND (c) AND (d) NOR
18. The expression A + A·B simplifies to (a) B (b) A (c) A·B (d) 1
19. Over four intervals, A is 0, 1, 0, 1 and B is 0, 0, 1, 1. The output of a NOR gate is (a) 0, 1, 1, 1 (b) 1, 1, 1, 0 (c) 0, 0, 0, 1 (d) 1, 0, 0, 0
20. In a sample, n_e = 16 n_h and n_i = 2 × 10¹⁶ m⁻³. The hole concentration is (a) 5 × 10¹⁵ m⁻³ (b) 8 × 10¹⁶ m⁻³ (c) 1.25 × 10¹⁵ m⁻³ (d) 2 × 10¹⁶ m⁻³
21. On heating, the resistance of a copper wire and of a pure silicon rod (a) both increase (b) both decrease (c) increases and decreases respectively (d) decreases and increases respectively
22. A full-wave rectifier on 50 Hz has V_m = 10 V, R_L = 1 kΩ and C = 1000 μF. The estimated ripple is (a) 0.2 V (b) 0.1 V (c) 1 V (d) 0.01 V
23. The peak output of a half-wave rectifier is 24 V. The rms value of the output is (a) 17 V (b) 7.6 V (c) 24 V (d) 12 V
24. A germanium junction (V₀ = 0.3 V) is forward biased with 0.2 V. The effective barrier is (a) 0.1 V (b) 0.5 V (c) 0.3 V (d) 0.2 V
25. The least number of NOR gates needed to make an OR gate is (a) 1 (b) 3 (c) 2 (d) 4
26. An LED emits 3 mW of light at 413 nm. The number of photons per second is about (a) 1.0 × 10¹⁶ (b) 6.25 × 10¹⁵ (c) 3.1 × 10¹⁵ (d) 1.9 × 10¹⁶
27. A solar panel of area 0.02 m² gives a maximum power of 2.4 W in sunlight of 1000 W m⁻². Its efficiency is (a) 24% (b) 2.4% (c) 8.3% (d) 12%
28. A 9.1 V Zener has a power rating of 0.455 W. Its maximum safe current is (a) 50 mA (b) 20 mA (c) 4.1 mA (d) 0.5 A
29. A 12 V battery, a lamp and an ideal diode are in series, with the diode reverse biased. The lamp current is (a) the same as without the diode (b) half of that without the diode (c) zero (d) very large
30. For Y = A·B + Ā·B̄ with A = 1 and B = 0, the output is (a) 1 (b) 0 (c) A (d) undefined
31. An n-type sample has n_e = 2 × 10²² m⁻³ and μ_e = 0.125 m² V⁻¹ s⁻¹. Neglecting holes, its resistivity is (a) 400 Ω m (b) 4 × 10⁻³ Ω m (c) 2.5 × 10⁻² Ω m (d) 2.5 × 10⁻³ Ω m
32. A half-wave rectifier with a silicon diode (0.7 V) has input peak 15 V and load 2 kΩ. The peak load current is (a) 7.15 mA (b) 7.5 mA (c) 7.85 mA (d) 0.35 mA
33. In a bridge rectifier, the number of diodes conducting during each half cycle is (a) 1 (b) 4 (c) 2 (d) 3
34. The material commonly used for blue LEDs is (a) GaAs (b) GaN (c) Si (d) Ge
35. A photodiode is operated in which quadrant of its I-V graph? (a) First (b) Second (c) Fourth (d) Third
36. Breakdown in a heavily doped Zener at about 4 V is mainly due to (a) a strong field pulling electrons from covalent bonds (b) impact ionisation by fast carriers only (c) melting of the junction (d) light falling on the junction
37. A 6 V Zener rated 0.3 W is used with a 16 V supply. The least series resistance that keeps it safe with no load is (a) 100 Ω (b) 320 Ω (c) 200 Ω (d) 50 Ω
38. For Y = NOT((A + B)·C) with A = 0, B = 0, C = 1, the output is (a) 0 (b) 1 (c) C (d) undefined
39. Silicon (n_i = 1.5 × 10¹⁶ m⁻³) has 6 × 10²² m⁻³ donors and 2 × 10²² m⁻³ acceptors. The hole concentration is about (a) 1.5 × 10¹⁶ m⁻³ (b) 3.75 × 10⁹ m⁻³ (c) 4 × 10²² m⁻³ (d) 5.6 × 10⁹ m⁻³
40. Two ideal diodes are in series with a 10 V battery and a resistor. One diode points with the current and the other against it. The current is (a) zero (b) 10 V divided by the resistance (c) half of 10 V divided by the resistance (d) very large
41. A solar cell has V_oc = 0.6 V and I_sc = 2.8 A. Its maximum power point is at 0.48 V and 2.5 A. The fill factor is about (a) 0.80 (b) 0.86 (c) 0.71 (d) 0.60
42. A full-wave rectifier has peak output 14.14 V. The rms value of the output is about (a) 7.07 V (b) 10 V (c) 9 V (d) 14.14 V
43. Assertion (A): An LED must be reverse biased to give out light. Reason (R): Light is emitted when electrons and holes recombine across the band gap. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true
44. Assertion (A): Below breakdown, the reverse current of a p-n junction is almost independent of the applied voltage. Reason (R): The reverse current is carried by minority carriers whose number is fixed mainly by temperature. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true
45. Statement I: The NOR gate is a universal gate. Statement II: In Boolean algebra, A + Ā = 0. (a) Both true (b) Both false (c) I true, II false (d) I false, II true
Answer key with reasons
| Q | Ans | Reason |
|---|---|---|
| 1 | b | n_e = (2.4 × 10¹⁹)²/(4.8 × 10²³) = 1.2 × 10¹⁵. |
| 2 | c | Photon energy 1240/1500 ≈ 0.83 eV: above 0.7, below 1.1. |
| 3 | a | Antimony is pentavalent, a donor. |
| 4 | d | 1.6 × 10⁻¹⁹ × 1.6 × 10¹⁶ × 0.19 ≈ 4.9 × 10⁻⁴ S/m. |
| 5 | b | 0.5/(0.25 × 10⁻⁶) = 2 × 10⁶ V/m. |
| 6 | a | 0.04 V/0.02 A = 2 Ω. |
| 7 | c | (6 − 0.7)/265 = 20 mA. |
| 8 | d | Minority carrier supply is set by temperature. |
| 9 | b | Secondary 10 V rms, V_m ≈ 14.14 V, V_dc = V_m/π ≈ 4.5 V. |
| 10 | c | Input 60 Hz; full-wave output 120 Hz. |
| 11 | a | V_m = 21.2 V; PIV = 2V_m ≈ 42.4 V. |
| 12 | d | 1240/2.1 ≈ 590 nm. |
| 13 | c | Small dark current makes the light signal stand out. |
| 14 | b | 0.7 × 0.62 × 4 ≈ 1.74 W. |
| 15 | a | I_s = 40 mA, I_L = 10 mA, I_z = 30 mA. |
| 16 | d | Divider gives 12 × 4/6 = 8 V, below 9 V, so the Zener is off. |
| 17 | c | 1 only when both inputs are 1. |
| 18 | b | Absorption: A + A·B = A. |
| 19 | d | NOR is 1 only in the first interval (0, 0). |
| 20 | a | 16 n_h² = n_i², so n_h = n_i/4 = 5 × 10¹⁵. |
| 21 | c | Metals: more scattering; semiconductors: more carriers. |
| 22 | b | ΔV ≈ 10/(100 × 1000 × 10⁻³) = 0.1 V. |
| 23 | d | Half-wave V_rms = V_m/2 = 12 V. |
| 24 | a | 0.3 − 0.2 = 0.1 V. |
| 25 | c | NOR then NOR-as-NOT. |
| 26 | b | E = 3.0 eV = 4.8 × 10⁻¹⁹ J; 3 × 10⁻³/4.8 × 10⁻¹⁹ = 6.25 × 10¹⁵. |
| 27 | d | Input 20 W; 2.4/20 = 12%. |
| 28 | a | 0.455/9.1 = 0.05 A. |
| 29 | c | A reverse-biased ideal diode is an open circuit. |
| 30 | b | A·B = 0 and Ā·B̄ = 0, so Y = 0. |
| 31 | d | σ = 400 S/m, ρ = 2.5 × 10⁻³ Ω m. |
| 32 | a | (15 − 0.7)/2000 = 7.15 mA. |
| 33 | c | Two diodes in series conduct in each half. |
| 34 | b | GaN has a gap near 3 eV. |
| 35 | d | Reverse voltage and reverse current: third quadrant. |
| 36 | a | Low-voltage breakdown is Zener (field) breakdown. |
| 37 | c | I_max = 0.3/6 = 50 mA; R_s = 10/0.05 = 200 Ω. |
| 38 | b | (0 + 0)·1 = 0, NOT gives 1. |
| 39 | d | n_e ≈ 4 × 10²²; n_h = 2.25 × 10³²/4 × 10²² ≈ 5.6 × 10⁹. |
| 40 | a | The reverse-biased diode blocks the whole series path. |
| 41 | c | (0.48 × 2.5)/(0.6 × 2.8) = 1.2/1.68 ≈ 0.71. |
| 42 | b | Full-wave V_rms = V_m/√2 = 10 V. |
| 43 | d | LEDs glow in forward bias; R is correct. |
| 44 | a | Fixed minority supply is why the current is flat. |
| 45 | c | NOR is universal; A + Ā = 1, not 0. |