Chapter 6 of 10 · 24 min read

Chapter 4: Special Diodes: LED, Photodiode and Solar Cell

What you will learn

  • How light and a p-n junction interact in three devices: photodiode, LED and solar cell.

  • Why a photodiode is used in reverse bias, and how its I-V curves change with light.

  • How an LED makes light, and how its band gap fixes its colour (λ = hc/E_g).

  • How a solar cell makes an emf with no battery, and the meaning of V_oc, I_sc and fill factor.

  • How to choose semiconductor materials for each device.

4.1 Three optoelectronic junction devices

All three devices are p-n junctions. They differ in which way energy flows and in how they are biased.

DeviceEnergy conversionBiasWorking region of I-V curve
PhotodiodeLight to electrical signalReverseThird quadrant
LEDElectrical energy to lightForwardFirst quadrant
Solar cellLight to electrical powerNone (it is the source)Fourth quadrant

The common rule is photon energy against band gap. A photon can create an electron-hole pair only if:

hν≥Eg⇔λ≤hcEgh\nu \ge E_g \quad \Leftrightarrow \quad \lambda \le \frac{hc}{E_g}

And when an electron and a hole recombine across the gap, the energy released is about E_g. With hc ≈ 1240 eV nm:

λ (nm)≈1240Eg (eV)\lambda\,(\text{nm}) \approx \frac{1240}{E_g\,(\text{eV})}

4.2 Photodiode

A photodiode is a p-n junction with a window that lets light reach the junction. It is operated in reverse bias.

Working.

  1. A photon with hν ≥ E_g is absorbed in or near the depletion region.

  2. It creates an electron-hole pair.

  3. The strong field of the depletion layer separates them before they recombine. Electrons go to the n side, holes to the p side.

  4. Electrons collecting on the n side and holes on the p side give an emf. In an external circuit, this adds to the reverse current.

More light means more pairs, so the reverse current (the photocurrent) rises in proportion to the light intensity.

Why reverse bias? Think of hearing a whisper. In a quiet library you notice it at once; at a cricket stadium you do not. In reverse bias the dark current is tiny (microamps), like the quiet library. The photocurrent is then a large fraction of the total, easy to measure. In forward bias, the majority current is already milliamps, and the light's small extra current is hard to notice.

Figure 4.1 · Photodiode I-V characteristics in reverse bias for three light intensities
Figure 4.1 · Photodiode I-V characteristics in reverse bias for three light intensities

Each curve is nearly flat in reverse voltage; a brighter light shifts the whole curve to a larger reverse current.

The I-V curves are drawn in the third quadrant. For each intensity, the reverse current is almost flat with voltage, and higher intensity gives a larger current.

Uses: detecting light in remote controls and optical fibre receivers, light meters, and counting objects on a conveyor belt.

Worked example 4.1: A photodiode is made from a semiconductor with E_g = 2.5 eV. Can it detect light of wavelength 600 nm? What is the longest wavelength it can detect?

Solution: Photon energy at 600 nm = 1240/600 ≈ 2.07 eV, which is less than 2.5 eV. So it cannot detect 600 nm light. The longest detectable wavelength is 1240/2.5 = 496 nm.

4.3 Light emitting diode (LED)

An LED is a heavily doped p-n junction that gives out light when forward biased.

Working.

  1. Forward bias pushes electrons from n to p and holes from p to n.

  2. Near the junction, there are now many extra minority carriers on both sides.

  3. They recombine with majority carriers. An electron drops from the CB to the VB.

  4. The energy released, about E_g, comes out as a photon.

As forward current rises, more recombination happens and brightness rises. Past a point, heating lowers the output again.

I-V characteristic. It looks like an ordinary diode curve, but the knee voltage is larger and depends on colour: about 1.8 V for red and about 3 V for blue. The reverse breakdown voltage of an LED is low, around 5 V, so it must not be reverse biased carelessly.

Choice of material. For visible light (about 400 nm to 700 nm), E_g must lie between about 1.8 eV and 3.1 eV. Silicon (1.1 eV) and germanium (0.7 eV) have gaps that are too small, and in them recombination mostly gives heat. So LEDs use compound semiconductors.

MaterialApprox. E_g (eV)Approx. λ (nm)Colour
GaAs1.4886Infrared (TV remotes)
GaAsP1.9650Red
GaP2.3540Green
GaN2.6 to 3.4365 to 480Blue to ultraviolet

A white LED is usually a blue LED coated with a yellow phosphor. The mix of blue and yellow looks white.

LEDs against filament bulbs.

  • Low working voltage and low power.

  • Switch on and off very fast, with no warm-up.

  • Long life and rugged; no filament to break.

  • Nearly single-colour light, with bandwidth of about 10 nm to 50 nm.

Worked example 4.2: A GaAsP LED has E_g = 1.9 eV. Find the wavelength it emits and its colour.

Solution: λ = 1240/1.9 ≈ 653 nm. This is red light.

Worked example 4.3: A blue LED emits at 470 nm. Estimate the band gap of its material.

Solution: E_g ≈ 1240/470 ≈ 2.64 eV.

Worked example 4.4: An LED gives out 5 mW of light at 620 nm. How many photons does it emit per second?

Solution: Photon energy = 1240/620 = 2.0 eV = 3.2 × 10⁻¹⁹ J.

N=PE=5×10−33.2×10−19≈1.56×1016 s−1N = \frac{P}{E} = \frac{5 \times 10^{-3}}{3.2 \times 10^{-19}} \approx 1.56 \times 10^{16}\ \text{s}^{-1}

Worked example 4.5 (NEET-hard): An LED carries 20 mA at 2.0 V. It emits 620 nm photons, and only one electron in four that crosses the junction produces a photon. Find the light power and the efficiency.

Solution: Electrons per second = I/e = 0.02/(1.6 × 10⁻¹⁹) = 1.25 × 10¹⁷. Photons per second = 1.25 × 10¹⁷/4 = 3.125 × 10¹⁶. Each photon carries 3.2 × 10⁻¹⁹ J.

Plight=3.125×1016×3.2×10−19=0.01 WP_{light} = 3.125 \times 10^{16} \times 3.2 \times 10^{-19} = 0.01\ \text{W}

Electrical input = 2.0 × 0.02 = 0.04 W. Efficiency = 0.01/0.04 = 25%.

4.4 Solar cell

A solar cell is a p-n junction that produces an emf when light falls on it. It needs no battery; it is the source.

Construction. A thick p-type silicon wafer (about 300 μm) carries a very thin n-type layer on top (about 0.3 μm). Thin metal fingers on top collect current without blocking much light. A metal layer covers the back. The top layer is thin so that light reaches the depletion region.

Three steps.

  1. Generation: photons with hν ≥ E_g create electron-hole pairs near the junction.

  2. Separation: the depletion field sends electrons to the n side and holes to the p side.

  3. Collection: electrons reach the front contact and holes the back contact. The n side becomes negative and the p side positive, giving a photovoltage.

Connect a load and a current flows from the p side, through the load, to the n side. Inside the cell, this current flows from n to p, opposite to the forward current of a diode. That is why the I-V curve sits in the fourth quadrant. Books usually redraw it in the first quadrant by flipping the current axis.

Figure 4.2 · Solar cell I-V characteristic with V_oc, I_sc and the maximum power point
Figure 4.2 · Solar cell I-V characteristic with V_oc, I_sc and the maximum power point

The curve meets the current axis at I_sc and the voltage axis at V_oc; the largest rectangle that fits under it marks the maximum power V_m × I_m.

Key points on the curve.

  • Open-circuit voltage V_oc: the voltage with no load (I = 0). For Si it is around 0.5 V to 0.6 V.

  • Short-circuit current I_sc: the current with the terminals shorted (V = 0). It is proportional to light intensity.

  • Maximum power point: the point where the product V × I is largest, near the knee of the curve.

Pmax=VmIm,FF=VmImVocIscP_{max} = V_m I_m, \qquad FF = \frac{V_m I_m}{V_{oc} I_{sc}}

The fill factor FF tells how "square" the curve is. Good cells have FF around 0.7 to 0.85. Efficiency compares output with the light power falling on the cell:

η=PmaxIlight×A\eta = \frac{P_{max}}{I_{light} \times A}

Choice of material. The sun's spectrum peaks near 1.5 eV. A good solar cell material has:

  • E_g between about 1.0 eV and 1.8 eV (ideally near 1.5 eV),

  • strong light absorption,

  • good electrical conductivity,

  • low cost and easy availability.

Si (1.1 eV) and GaAs (1.43 eV) are widely used. A gap far above 2 eV wastes most of sunlight. A gap far below 1 eV wastes the extra energy of each photon as heat.

Worked example 4.6: A solar cell has V_oc = 0.6 V, I_sc = 3 A and fill factor 0.75. Find its maximum power. If its area is 100 cm² and sunlight gives 1000 W m⁻², find its efficiency.

Solution: P_max = FF × V_oc × I_sc = 0.75 × 0.6 × 3 = 1.35 W. Light power = 1000 × 0.01 = 10 W. Efficiency = 1.35/10 = 13.5%.

Worked example 4.7: Each cell of a rooftop panel has V_oc = 0.5 V. How many cells in series give an open-circuit voltage of 18 V?

Solution: n = 18/0.5 = 36 cells.

Quick revision

  • Photodiode: reverse bias, light to signal, current rises with intensity, third quadrant.

  • LED: forward bias, recombination gives photons with energy about E_g.

  • λ (nm) ≈ 1240/E_g (eV); visible LEDs need E_g from about 1.8 eV to 3.1 eV.

  • Si and Ge are not used for visible LEDs: gaps too small, energy lost as heat.

  • Solar cell: no bias, generation, separation, collection; fourth-quadrant I-V.

  • I_sc is proportional to intensity; P_max = V_m I_m; FF = V_m I_m/(V_oc I_sc).

  • Best solar cell gap is about 1.5 eV; Si and GaAs are common.

NEET traps

  • Saying a photodiode works in forward bias. It works in reverse bias.

  • Using E_g in joules with 1240. The shortcut 1240/E_g needs E_g in eV and gives λ in nm.

  • Thinking a solar cell needs a battery. It is itself the source.

  • Placing the solar cell curve in the first quadrant without noting the axis flip.

  • Saying LED colour depends on current. Colour is set by band gap; current changes brightness.

  • Choosing the largest band gap for a solar cell. Too large a gap wastes most of sunlight.

Practice MCQs: Chapter 4

Level 1: Concept check

1. An LED gives out light when it is (a) reverse biased (b) forward biased (c) unbiased (d) in breakdown

2. A photodiode is normally operated (a) in forward bias (b) with no bias at all (c) in breakdown (d) in reverse bias

3. A solar cell produces electrical power (a) without any external bias (b) only in forward bias (c) only in reverse bias (d) only in the dark

4. The colour of light from an LED is decided mainly by (a) the current through it (b) the applied voltage polarity (c) the band gap of its material (d) the size of the chip

5. The I-V characteristic of a solar cell lies in the (a) first quadrant (b) fourth quadrant (c) second quadrant (d) third quadrant only

6. Silicon is not used to make visible LEDs mainly because (a) it is too costly (b) it cannot be doped (c) it is a conductor (d) its band gap is too small and recombination gives mostly heat

7. The reverse current of a photodiode increases when (a) the light intensity increases (b) the light is switched off (c) the reverse voltage is reduced to zero (d) the window is covered

8. The device that changes light directly into electrical power without any battery is the (a) LED (b) Zener diode (c) solar cell (d) rectifier diode

9. The short-circuit current of a solar cell is (a) independent of light intensity (b) proportional to light intensity (c) inversely proportional to light intensity (d) zero in bright light

10. The best band gap for a solar cell material is close to (a) 0.1 eV (b) 5 eV (c) 10 eV (d) 1.5 eV

Level 2: NEET standard

11. An LED is made from a material with E_g = 2.0 eV. The emitted wavelength is about (a) 620 nm (b) 496 nm (c) 2480 nm (d) 310 nm

12. A green LED emits at 540 nm. The band gap of its material is about (a) 1.80 eV (b) 2.00 eV (c) 2.30 eV (d) 2.80 eV

13. A photodiode material has E_g = 2.8 eV. Which wavelength can it detect? (a) 700 nm (b) 600 nm (c) 500 nm (d) 400 nm

14. A solar cell has V_oc = 0.55 V, I_sc = 2 A and fill factor 0.8. Its maximum power is (a) 1.10 W (b) 0.88 W (c) 1.38 W (d) 0.69 W

15. A solar cell of area 200 cm² gives a maximum power of 2 W in light of intensity 800 W m⁻². Its efficiency is (a) 12.5% (b) 25% (c) 8% (d) 1.25%

16. An LED emits 4 mW of light at 496 nm. The number of photons emitted per second is about (a) 2.5 × 10¹⁶ (b) 4 × 10¹⁵ (c) 1 × 10¹⁶ (d) 1 × 10¹⁹

17. A photodiode gives a photocurrent of 15 μA in light of intensity 2 mW cm⁻². Neglecting dark current, at 5 mW cm⁻² the photocurrent is (a) 15 μA (b) 6 μA (c) 30 μA (d) 37.5 μA

18. An LED with a forward drop of 2 V must carry 20 mA from a 9 V supply. The series resistance needed is (a) 450 Ω (b) 350 Ω (c) 100 Ω (d) 550 Ω

19. A photodiode is used in reverse bias because (a) the fractional change in current due to light is much larger than in forward bias (b) it cannot conduct in forward bias (c) light cannot reach the junction in forward bias (d) the band gap rises in reverse bias

20. For a solar cell at the open-circuit point (a) the power output is maximum (b) the current is maximum (c) the current is zero, so the power is zero (d) the voltage is zero

21. Each cell of a panel has V_oc = 0.6 V. To get an open-circuit voltage of 18 V, the number of cells in series is (a) 18 (b) 20 (c) 25 (d) 30

22. For an LED to emit visible light, its band gap should lie roughly between (a) 0.5 eV and 1.0 eV (b) 1.8 eV and 3.1 eV (c) 4 eV and 6 eV (d) 6 eV and 9 eV

Level 3: Challenge

23. An LED carries 25 mA. It emits 590 nm photons, and 40% of the electrons crossing the junction produce a photon. The light power output is about (a) 8.4 mW (b) 52.5 mW (c) 21 mW (d) 10.5 mW

24. A photodiode responds to wavelengths up to 1.0 μm and no longer. The band gap of its material is about (a) 1.24 eV (b) 0.62 eV (c) 2.48 eV (d) 1.10 eV

25. Four points on a solar cell's I-V curve are (0.40 V, 2.8 A), (0.45 V, 2.6 A), (0.50 V, 2.2 A) and (0.55 V, 1.2 A). The largest power among these is (a) 1.12 W (b) 1.10 W (c) 0.66 W (d) 1.17 W

26. A red LED has E_g = 1.9 eV and a blue LED has E_g = 2.8 eV. The ratio of the red wavelength to the blue wavelength is about (a) 0.68 (b) 1.47 (c) 2.17 (d) 1.00

27. In a solar cell, the top layer is made very thin so that (a) the cell is lighter (b) the band gap becomes smaller (c) light can reach the depletion region and create pairs there (d) the reverse current is reduced

28. An LED made from GaAs (E_g ≈ 1.4 eV) emits radiation of wavelength about (a) 886 nm, in the infrared (b) 620 nm, red (c) 443 nm, blue (d) 1771 nm, far infrared

29. Assertion (A): A photodiode is used in forward bias to detect light. Reason (R): The photocurrent is easiest to notice when the dark current is very small. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: The short-circuit current of a solar cell increases as the light intensity increases. Statement II: A white LED is commonly a blue LED coated with a yellow phosphor. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1bForward bias drives recombination, which emits photons.
2dReverse bias keeps dark current tiny.
3aThe cell itself is the source.
4cPhoton energy is about E_g.
5bCell drives current opposite to diode forward current at positive V.
6dSi gap is 1.1 eV (infrared) and recombination is mostly non-radiative.
7aMore photons, more pairs, more photocurrent.
8cSolar cell is a photovoltaic source.
9bI_sc rises in proportion to the number of photons.
10dSun's spectrum peaks near 1.5 eV.
11a1240/2.0 = 620 nm.
12c1240/540 ≈ 2.30 eV.
13dCut-off is 1240/2.8 ≈ 443 nm; only 400 nm is shorter.
14b0.8 × 0.55 × 2 = 0.88 W.
15aInput 800 × 0.02 = 16 W; 2/16 = 12.5%.
16cE = 2.5 eV = 4 × 10⁻¹⁹ J; 4 × 10⁻³/4 × 10⁻¹⁹ = 10¹⁶.
17dPhotocurrent is proportional to intensity: 15 × 5/2 = 37.5 μA.
18bR = (9 − 2)/0.02 = 350 Ω.
19aSmall dark current makes the light-induced change stand out.
20cI = 0 at V_oc, so P = 0.
21d18/0.6 = 30.
22bVisible range 400 to 700 nm maps to about 3.1 to 1.8 eV.
23c0.4 × 0.025/e = 6.25 × 10¹⁶ photons/s × 2.10 eV ≈ 21 mW.
24aE_g = 1240/1000 = 1.24 eV.
25d0.45 × 2.6 = 1.17 W is the largest product.
26bλ is inversely proportional to E_g: 2.8/1.9 ≈ 1.47.
27cLight must reach the junction field to separate pairs.
28a1240/1.4 ≈ 886 nm, infrared.
29dPhotodiodes work in reverse bias; R is a true fact.
30aBoth are correct facts.

Chapter 4 revision sheet

One-page summary

  • All three devices rest on one rule: a photon makes (or comes from) an electron-hole pair only when hν is at least E_g.

  • λ (nm) ≈ 1240/E (eV); larger band gap means shorter wavelength.

  • Photodiode: reverse biased, light makes pairs in the depletion region, the field sweeps them out as photocurrent.

  • Photocurrent is nearly proportional to light intensity and almost independent of reverse voltage; I-V curves lie in the third quadrant.

  • Reverse bias is used because the light makes a large fractional change in the small reverse current.

  • Uses of photodiodes: light detection, remote-control receivers, optical communication.

  • LED: forward biased, electrons and holes recombine at the junction and give photons of energy about E_g.

  • LED I-V looks like an ordinary diode but with a higher knee (about 1.8 V for red, about 3 V for blue).

  • Visible LEDs need E_g from about 1.8 eV to 3.1 eV, so they use GaAsP, GaN and similar compounds, not Si or Ge.

  • LEDs: low voltage, long life, fast switching, little heat; light is nearly single-colour but not coherent.

  • Solar cell: no external bias; three steps are generation, separation and collection of carriers.

  • Solar cell I-V lies in the fourth quadrant; key points are V_oc (no current) and I_sc (shorted).

  • P_max = V_m I_m; fill factor FF = V_m I_m/(V_oc I_sc); efficiency η = P_max/P_in.

  • Best solar-cell gap is about 1.5 eV; Si (1.1 eV) and GaAs (1.4 eV) are common.

  • Cells in series add voltage; cells in parallel add current.

Must-remember table

DeviceBiasI-V quadrantKey formula or value
PhotodiodeReverseThirdI_photo proportional to intensity; needs hν ≥ E_g
LEDForwardFirstλ (nm) = 1240/E_g (eV)
Solar cellNoneFourthFF = V_m I_m/(V_oc I_sc); η = P_max/P_in
Photon count——N = P/E per second
Red, green, blue gaps——about 1.9, 2.3, 2.7 eV (about 650, 540, 460 nm)
Ideal solar gap——about 1.5 eV

Memory aids

  • "LED Lights Forward, Photodiode Prefers Reverse, Solar Supplies itself": the bias of each device.

  • "1-3-4": LED curve in the 1st quadrant, photodiode in the 3rd, solar cell in the 4th.

  • "Gap up, colour Blue": a bigger band gap pushes the colour from red towards blue.

  • "GSC": Generation, Separation, Collection, the three steps inside a solar cell.

  • "1240 makes it simple": divide 1240 by eV to get nm, or by nm to get eV.

Concept connections

  • Photon energy, photon flux and the threshold idea come from Physics Book 17: Dual Nature of Matter and Radiation.

  • Colours and wavelengths of visible light link to Physics Book 15: Electromagnetic Waves.

  • Plants also turn light into usable energy in photosynthesis, covered in Biology Book 4: Plant Physiology.

Practice MCQs: Chapter 4, Level 4 (new NEET pattern)

31. Match List I (device) with List II (how it is operated).

  • List I: A. Photodiode · B. LED · C. Solar cell · D. Zener regulator

  • List II: i. forward bias · ii. no external bias, I-V in the fourth quadrant · iii. reverse bias in breakdown · iv. reverse bias below breakdown

(a) A-iv, B-i, C-ii, D-iii (b) A-i, B-iv, C-ii, D-iii (c) A-iv, B-i, C-iii, D-ii (d) A-iii, B-i, C-ii, D-iv

32. Match the LED band gap (List I) with the emitted wavelength (List II).

  • List I: A. 1.9 eV · B. 2.3 eV · C. 2.7 eV · D. 1.4 eV

  • List II: i. about 460 nm (blue) · ii. about 890 nm (infrared) · iii. about 650 nm (red) · iv. about 540 nm (green)

(a) A-iv, B-iii, C-i, D-ii (b) A-iii, B-iv, C-ii, D-i (c) A-iii, B-iv, C-i, D-ii (d) A-i, B-iv, C-iii, D-ii

33. Match List I (solar cell term) with List II (meaning).

  • List I: A. Open-circuit voltage · B. Short-circuit current · C. Fill factor · D. Efficiency

  • List II: i. P_max/(V_oc I_sc) · ii. voltage when no current is drawn · iii. P_max divided by incident light power · iv. current when the terminals are joined by a wire

(a) A-iv, B-ii, C-i, D-iii (b) A-ii, B-iv, C-iii, D-i (c) A-i, B-iv, C-ii, D-iii (d) A-ii, B-iv, C-i, D-iii

34. Match List I with List II (hc = 1240 eV nm, 1 eV = 1.6 × 10⁻¹⁹ J).

  • List I: A. Energy of a 620 nm photon · B. Photons per second in a 2 mW beam of 620 nm · C. Wavelength of a 2.48 eV photon · D. Energy of a 1240 nm photon

  • List II: i. 6.25 × 10¹⁵ s⁻¹ · ii. 2.0 eV · iii. 1.0 eV · iv. 500 nm

(a) A-i, B-ii, C-iv, D-iii (b) A-ii, B-i, C-iv, D-iii (c) A-ii, B-iv, C-i, D-iii (d) A-iii, B-i, C-iv, D-ii

35. How many of the following statements are correct?

  • A. An LED is a forward-biased p-n junction.

  • B. The photocurrent of a photodiode is nearly proportional to the light intensity.

  • C. A solar cell needs an external battery to work.

  • D. Visible LEDs are usually made of silicon.

(a) one (b) two (c) three (d) four

36. Choose the correct set of statements.

  • A. A photodiode is run in reverse bias because light changes the reverse current by a much larger fraction.

  • B. The I-V curve of a solar cell is drawn in the fourth quadrant.

  • C. The light from an LED is coherent like a laser beam.

  • D. A solar cell has a large junction area facing the light.

(a) A and B only (b) B, C and D only (c) A, B and D only (d) A and C only

37. How many of the following statements are correct?

  • A. Visible LEDs need a band gap of roughly 1.8 eV to 3.1 eV.

  • B. Silicon is the ideal material for a visible LED.

  • C. The ideal band gap for a solar cell is about 1.5 eV.

  • D. A photodiode cannot detect photons whose energy is below its band gap.

(a) one (b) two (c) three (d) four

38. Choose the correct set of statements about a photodiode.

  • A. In the dark, its reverse current is the small leakage current.

  • B. Shining light on it increases its reverse current.

  • C. It detects light through changes in its forward current.

  • D. At fixed light intensity, raising the reverse voltage greatly increases the photocurrent.

(a) A and B only (b) A, B and C only (c) B and D only (d) C and D only

39. A graph shows the reverse-bias I-V curves of a photodiode for three light intensities I₁, I₂ and I₃. Each curve is almost a flat horizontal line in the third quadrant, at −10 µA, −20 µA and −30 µA respectively. The ratio I₃ : I₁ is about

(a) 1 : 3 (b) 9 : 1 (c) √3 : 1 (d) 3 : 1

40. A solar cell's I-V curve gives V_oc = 0.6 V and I_sc = 3.0 A. The maximum power point is at 0.48 V and 2.5 A. The fill factor is about

(a) 0.80 (b) 0.67 (c) 0.50 (d) 1.5

41. Turn-on voltages of four LEDs are given.

LEDRedGreenBlueInfrared
Voltage (V)1.82.23.01.2

One of them, in series with 160 Ω across a 5 V supply, carries 20 mA. It is the

(a) red LED (b) green LED (c) blue LED (d) infrared LED

Case for Q42–43. A rooftop panel in Jaipur has 36 identical cells in series, each with V_oc = 0.6 V. The panel area is 0.5 m². At noon, sunlight brings 1000 W m⁻² and the panel's maximum output is 75 W.

42. The open-circuit voltage of the panel is

(a) 0.6 V (b) 18 V (c) 60 V (d) 21.6 V

43. The efficiency of the panel is

(a) 7.5% (b) 75% (c) 15% (d) 30%

44. A red LED emits photons of energy 2.0 eV. It carries 10 mA, and only 25% of the electrons crossing the junction produce a photon. The light power emitted is

(a) 20 mW (b) 5 mW (c) 2.5 mW (d) 10 mW

45. A silicon photodiode (E_g = 1.1 eV) is lit in turn by sources of 650 nm, 1000 nm and 1300 nm. A photocurrent appears for

(a) 650 nm and 1000 nm only (b) 650 nm only (c) all three (d) 1300 nm only

Level 4 answer key

QAnsReason
31aPhotodiode reverse (no breakdown), LED forward, solar cell unbiased in fourth quadrant, Zener in breakdown
32c1240/1.9 ≈ 653 nm, 1240/2.3 ≈ 539 nm, 1240/2.7 ≈ 459 nm, 1240/1.4 ≈ 886 nm
33dV_oc at zero current, I_sc at zero voltage, FF and η as defined
34b1240/620 = 2.0 eV; 2 × 10⁻³/(3.2 × 10⁻¹⁹) = 6.25 × 10¹⁵; 1240/2.48 = 500 nm; 1240/1240 = 1.0 eV
35bA and B true; a solar cell makes its own emf (C false); Si's gap is too small for visible light (D false)
36cLED light is not coherent (C false)
37cA, C, D true; Si is not used for visible LEDs (B false)
38aDetection uses reverse current (C false); photocurrent hardly depends on reverse voltage (D false)
39dPhotocurrent is proportional to intensity: 30/10 = 3
40bFF = (0.48 × 2.5)/(0.6 × 3.0) = 1.2/1.8 ≈ 0.67
41aLED voltage = 5 − 0.020 × 160 = 5 − 3.2 = 1.8 V, the red LED
42dSeries cells add: 36 × 0.6 = 21.6 V
43cP_in = 1000 × 0.5 = 500 W; η = 75/500 = 15%
44bPhotons/s = 0.25 × I/e; power = 0.25 × 0.010 A × 2.0 V = 5 mW
45aPhoton energies 1.91, 1.24 and 0.95 eV; only the first two exceed 1.1 eV
24 min left
‹
›