Chapter 7 of 10 · 23 min read

Chapter 5: Zener Diode and Voltage Regulation

What you will learn

  • What makes a Zener diode different from an ordinary diode.

  • How Zener and avalanche breakdown happen.

  • The Zener I-V characteristic and why its voltage stays fixed in breakdown.

  • How a Zener regulator holds the load voltage steady against changes in input and load.

  • How to solve regulator numericals: currents, power, and the limits on R_s and R_L.

5.1 The Zener diode

A Zener diode is a p-n junction made to work in reverse breakdown without damage. Both sides are heavily doped. So the depletion layer is very thin, and even a few volts give a huge field across it.

Its symbol is a diode arrow with a bent bar (like a Z) at the cathode. It is connected in reverse bias in circuits: cathode to the higher potential.

The reverse voltage at which breakdown starts is the Zener voltage V_z. Manufacturers make Zeners with V_z from about 2 V to a few hundred volts, by choosing the doping.

5.2 How breakdown happens

Zener breakdown (field emission). In a heavily doped junction, the depletion layer is very thin. A small reverse voltage then sets up a field of the order of 10⁶ to 10⁷ V/m or more. Such a field can pull electrons straight out of covalent bonds on the p side. These extra carriers make the reverse current jump. This happens at low V_z, roughly below 5 V to 6 V.

Avalanche breakdown. In a lightly doped junction, the layer is wider. Minority carriers are accelerated by the field and gain enough energy to knock electrons out of bonds when they collide. Each freed electron is accelerated in turn and frees more, like a cascade. This dominates at higher breakdown voltages.

For NEET, remember: heavier doping gives a thinner layer, a stronger field and a lower breakdown voltage.

5.3 The I-V characteristic

Figure 5.1 · Zener diode I-V characteristic with the breakdown voltage V_z
Figure 5.1 · Zener diode I-V characteristic with the breakdown voltage V_z

Past −V_z the curve drops almost vertically: the current can change a lot while the voltage stays at V_z.

  • Forward bias: just like an ordinary silicon diode. Current rises after about 0.7 V.

  • Reverse bias below V_z: a tiny reverse saturation current flows.

  • Reverse bias at V_z: current rises sharply, while the voltage stays almost exactly at V_z.

The last point is the key. In breakdown, a big change in Zener current makes only a tiny change in Zener voltage. The dynamic resistance in that region is very small. This is what lets a Zener hold a voltage steady.

The current must stay below a maximum set by the power rating:

Iz,max=PmaxVzI_{z,max} = \frac{P_{max}}{V_z}

5.4 Zener diode as a voltage regulator

A rectifier with a filter gives dc that still changes with mains fluctuation and with load. A Zener regulator fixes this.

Circuit. The unregulated dc input V_in feeds a series resistor R_s. After R_s, the Zener (reverse biased) and the load R_L are in parallel.

Figure 5.2 · Zener voltage regulator: series resistor, Zener and load in parallel
Figure 5.2 · Zener voltage regulator: series resistor, Zener and load in parallel

The series current I_s splits at the node: I_L goes to the load and the rest, I_z, goes through the Zener, which holds the load voltage at V_z.

Because the Zener and the load are in parallel, the load voltage equals V_z whenever the Zener is in breakdown. Three currents follow:

Is=Vin−VzRs,IL=VzRL,Iz=Is−ILI_s = \frac{V_{in} - V_z}{R_s}, \qquad I_L = \frac{V_z}{R_L}, \qquad I_z = I_s - I_L

How it regulates.

  • Input rises: I_s rises. The load voltage is held at V_z, so I_L is unchanged. The extra current goes into the Zener. The extra voltage drops across R_s.

  • Input falls: I_s falls, and the Zener current falls by the same amount. The load still sees V_z.

  • Load draws more current (R_L falls): I_s stays the same, so I_z falls to make room.

Think of a dam with a spillway. The water level (V_z) stays at the spillway height. Extra inflow (higher input) just spills over (Zener current). Too little inflow and the level drops below the spillway (Zener leaves breakdown).

Is the Zener in breakdown? Check first. Remove the Zener and find the voltage across R_L by the potential divider rule:

VL,open=Vin RLRs+RLV_{L,open} = V_{in}\,\frac{R_L}{R_s + R_L}

If this is at least V_z, the Zener is in breakdown and V_L = V_z. If it is less, the Zener is off, I_z = 0, and V_L = V_L,open.

Limits.

  • I_z must stay above a small minimum I_z,min to remain in breakdown.

  • I_z must stay below I_z,max to avoid overheating. The worst case is the largest input with no load.

ConditionEffect on I_sEffect on I_LEffect on I_z
V_in increasesIncreasesUnchangedIncreases
V_in decreasesDecreasesUnchangedDecreases
R_L decreasesUnchangedIncreasesDecreases
Load removedUnchangedBecomes zeroEquals I_s (largest)

Worked example 5.1: A Zener regulator has V_in = 12 V, V_z = 6 V, R_s = 200 Ω and R_L = 1 kΩ. Find I_s, I_L, I_z and the Zener power.

Solution: Check: V_L,open = 12 × 1000/1200 = 10 V, above 6 V, so the Zener is in breakdown.

Is=12−6200=30 mA,IL=61000=6 mA,Iz=24 mAI_s = \frac{12 - 6}{200} = 30\ \text{mA}, \quad I_L = \frac{6}{1000} = 6\ \text{mA}, \quad I_z = 24\ \text{mA}

Zener power = 6 × 0.024 = 0.144 W.

Worked example 5.2: A 9 V Zener must supply a 10 mA load from a 15 V source, with 20 mA flowing in the Zener. Find R_s.

Solution: I_s = 10 + 20 = 30 mA. R_s = (15 − 9)/0.03 = 200 Ω.

Worked example 5.3: The input of a regulator varies from 10 V to 14 V. V_z = 6 V, R_s = 100 Ω and R_L = 300 Ω. Find the range of Zener current.

Solution: I_L = 6/300 = 20 mA, fixed. I_s goes from (10 − 6)/100 = 40 mA to (14 − 6)/100 = 80 mA. So I_z goes from 20 mA to 60 mA. The load voltage stays at 6 V throughout.

Worked example 5.4: V_in = 10 V, V_z = 8 V, R_s = 1 kΩ and R_L = 2 kΩ. Find the load voltage.

Solution: V_L,open = 10 × 2000/3000 ≈ 6.67 V. This is less than 8 V, so the Zener never reaches breakdown. I_z = 0 and V_L ≈ 6.67 V. Using 8 V here would be a mistake.

Worked example 5.5: V_in = 20 V, V_z = 10 V and R_s = 500 Ω. Treating I_z,min as zero, find the smallest load resistance for which the output stays at 10 V.

Solution: I_s = (20 − 10)/500 = 20 mA. The load can take at most all of it: I_L,max = 20 mA. So R_L,min = 10/0.02 = 500 Ω.

Worked example 5.6 (NEET-hard): A 5 V Zener has a power rating of 0.5 W. It is used with a 15 V supply. Find the least R_s that keeps it safe even if the load is disconnected.

Solution: I_z,max = 0.5/5 = 0.1 A. With no load, all of I_s flows in the Zener: I_s ≤ 0.1 A.

Rs,min=15−50.1=100 ΩR_{s,min} = \frac{15 - 5}{0.1} = 100\ \Omega

Worked example 5.7 (NEET-hard): Two Zeners, of 5 V and 7 V, are in series and both reverse biased. They are connected to a 20 V supply through a 400 Ω resistor. Find the current.

Solution: Both are in breakdown, since 20 V exceeds 5 + 7 = 12 V. The resistor takes 20 − 12 = 8 V. I = 8/400 = 20 mA.

Quick revision

  • Zener: heavily doped, thin depletion layer, used in reverse breakdown.

  • Heavier doping, lower V_z. Low V_z: Zener (field) breakdown; high V_z: avalanche.

  • In breakdown the voltage stays at V_z over a wide range of current.

  • Regulator: R_s in series, Zener parallel to load.

  • I_s = (V_in − V_z)/R_s, I_L = V_z/R_L, I_z = I_s − I_L.

  • Check breakdown first with the divider V_in R_L/(R_s + R_L).

  • I_z,max = P_max/V_z; worst case is maximum input with no load.

NEET traps

  • Connecting the Zener forward biased and still writing V_z. Forward biased, it is just a 0.7 V diode.

  • Taking V_L = V_z without checking that the Zener is actually in breakdown.

  • Forgetting that I_z = I_s − I_L, not I_s.

  • Thinking the series resistor is optional. Without R_s the Zener current is unlimited.

  • Saying load current changes when only the input changes. With the Zener in breakdown, I_L stays V_z/R_L.

Practice MCQs: Chapter 5

Level 1: Concept check

1. A Zener diode used as a regulator works in (a) forward bias (b) reverse bias below breakdown (c) reverse breakdown (d) zero bias

2. Compared with an ordinary diode, a Zener diode is (a) heavily doped on both sides (b) lightly doped on both sides (c) undoped (d) doped only on the n side

3. In a Zener regulator, the Zener diode is connected (a) in series with the load (b) in series with the source only (c) across the series resistor (d) in parallel with the load

4. In the breakdown region, the voltage across a Zener diode (a) rises in proportion to current (b) stays nearly constant (c) falls to zero (d) reverses sign

5. The series resistor in a Zener regulator (a) raises the output voltage (b) stores charge (c) limits the current and drops the extra voltage (d) makes the Zener forward biased

6. Zener breakdown in a heavily doped junction is caused by (a) heating of the leads (b) recombination of carriers (c) light falling on the junction (d) a strong field pulling electrons out of covalent bonds

7. A Zener diode in forward bias behaves like (a) an ordinary diode (b) an open circuit always (c) a constant V_z source (d) a capacitor

8. In a working Zener regulator, if the input voltage rises, the Zener current (a) decreases (b) increases (c) stays the same (d) becomes zero

9. A Zener diode is mainly used as a (a) rectifier (b) light source (c) voltage regulator (d) light detector

10. Heavier doping of a Zener junction makes its breakdown voltage (a) higher (b) unchanged (c) infinite (d) lower

Level 2: NEET standard

11. A 6 V Zener is fed from 10 V through a 100 Ω resistor, with no load. The Zener current is (a) 40 mA (b) 60 mA (c) 100 mA (d) 16 mA

12. A regulator has V_in = 15 V, V_z = 5 V, R_s = 250 Ω and R_L = 1 kΩ. The Zener current is (a) 40 mA (b) 45 mA (c) 35 mA (d) 5 mA

13. In Question 12, the power dissipated in the Zener is (a) 0.20 W (b) 0.175 W (c) 0.525 W (d) 0.025 W

14. A 6.2 V Zener has a power rating of 1.24 W. Its maximum safe current is (a) 0.5 A (b) 7.7 A (c) 0.02 A (d) 0.2 A

15. An 8 V Zener is to supply 10 mA to a load from a 12 V source, with 10 mA through the Zener. The series resistance needed is (a) 200 Ω (b) 400 Ω (c) 100 Ω (d) 800 Ω

16. In a regulator with V_z = 6 V and R_s = 200 Ω, the input rises from 10 V to 12 V with the load fixed. The Zener current rises by (a) 5 mA (b) 10 mA (c) 20 mA (d) 30 mA

17. A 6 V Zener, R_s = 1 kΩ and R_L = 1 kΩ are used with V_in = 9 V. The load voltage is (a) 6.0 V (b) 3.0 V (c) 4.5 V (d) 9.0 V

18. In a working regulator, the load resistance is reduced (more load current). The Zener current (a) increases (b) stays the same (c) doubles (d) decreases

19. A Zener with V_z = 4 V has a depletion layer 0.8 μm wide at breakdown. The average field in it is (a) 5 × 10⁶ V m⁻¹ (b) 3.2 × 10⁶ V m⁻¹ (c) 5 × 10⁵ V m⁻¹ (d) 2 × 10⁵ V m⁻¹

20. A 12 V Zener in breakdown is part of a regulator fed with 18 V. The output voltage is (a) 18 V (b) 12 V (c) 6 V (d) 30 V

21. V_in = 20 V, V_z = 10 V and R_s = 500 Ω. Taking I_z,min as zero, the least load resistance for regulation is (a) 250 Ω (b) 1000 Ω (c) 500 Ω (d) 2000 Ω

22. V_in = 16 V, V_z = 10 V, R_s = 300 Ω and R_L = 2 kΩ. The Zener current is (a) 20 mA (b) 5 mA (c) 25 mA (d) 15 mA

Level 3: Challenge

23. A 5 V Zener rated 0.5 W is used with a 15 V supply. The least series resistance that keeps it safe with the load removed is (a) 50 Ω (b) 100 Ω (c) 150 Ω (d) 200 Ω

24. The input of a regulator varies from 12 V to 18 V. V_z = 9 V, R_s = 150 Ω and R_L = 900 Ω. The Zener current varies from (a) 10 mA to 50 mA (b) 20 mA to 60 mA (c) 0 to 40 mA (d) 10 mA to 60 mA

25. A 9 V Zener must regulate for a 30 mA load when the input falls to its lowest value of 12 V. The Zener needs at least 5 mA. The largest allowed R_s is about (a) 100 Ω (b) 300 Ω (c) 75 Ω (d) 86 Ω

26. Zeners of 5 V and 7 V are in series, both reverse biased, across a 20 V supply through 400 Ω. The current is (a) 50 mA (b) 30 mA (c) 20 mA (d) 12.5 mA

27. A 6 V Zener (silicon, 0.7 V forward drop) is connected forward biased in series with 465 Ω across a 10 V supply. The current is (a) 20 mA (b) 8.6 mA (c) 21.5 mA (d) zero

28. A regulator has V_in = 24 V, R_s = 400 Ω and V_z = 12 V. The load can be anything from open circuit down to 2 kΩ. The largest power the Zener must handle is (a) 0.29 W (b) 0.36 W (c) 0.72 W (d) 0.07 W

29. Assertion (A): A Zener diode is heavily doped on both sides. Reason (R): In forward bias, a Zener diode behaves like an ordinary diode. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: A Zener diode used as a voltage regulator works in forward bias. Statement II: In a heavily doped junction, breakdown happens at a low voltage because the thin depletion layer carries a very strong field. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1cRegulation uses the flat voltage of reverse breakdown.
2aHeavy doping gives a thin layer and low V_z.
3dThe load voltage equals V_z only if they are in parallel.
4bLarge current change, tiny voltage change.
5cR_s takes V_in − V_z and limits I_s.
6dField emission from bonds in a thin, high-field layer.
7aForward biased, it is a normal p-n diode.
8bExtra I_s goes into the Zener.
9cIts fixed breakdown voltage regulates.
10dThinner layer, stronger field, earlier breakdown.
11a(10 − 6)/100 = 40 mA, all through the Zener.
12cI_s = 40 mA, I_L = 5 mA, I_z = 35 mA.
13b5 × 0.035 = 0.175 W.
14d1.24/6.2 = 0.2 A.
15a(12 − 8)/0.020 = 200 Ω.
16bΔI_s = 2/200 = 10 mA; I_L fixed.
17cDivider gives 4.5 V, below 6 V, so the Zener is off.
18dI_s fixed, I_L up, so I_z down.
19a4/(0.8 × 10⁻⁶) = 5 × 10⁶ V/m.
20bOutput is held at V_z.
21cI_s = 20 mA; R_L,min = 10/0.02 = 500 Ω.
22dI_s = 20 mA, I_L = 5 mA, I_z = 15 mA.
23bI_z,max = 0.1 A; R_s = 10/0.1 = 100 Ω.
24aI_L = 10 mA; I_s from 20 to 60 mA; I_z from 10 to 50 mA.
25dR_s = (12 − 9)/(0.030 + 0.005) ≈ 86 Ω.
26c(20 − 12)/400 = 20 mA.
27aForward biased: (10 − 0.7)/465 = 20 mA.
28bWorst case no load: I_z = 12/400 = 30 mA; 12 × 0.03 = 0.36 W.
29bBoth true, but forward behaviour says nothing about why it is doped heavily.
30dRegulation uses reverse breakdown; II is correct.

Chapter 5 revision sheet

One-page summary

  • A Zener diode is a heavily doped p-n junction built to work safely in reverse breakdown.

  • Heavy doping gives a very thin depletion region, so a few volts make a huge field there.

  • Zener breakdown: the strong field pulls electrons straight out of bonds; it occurs in heavily doped diodes with low V_z.

  • Avalanche breakdown: in lightly doped diodes, carriers speed up and knock out more carriers by collision.

  • I-V curve: forward like a normal diode; reverse, a tiny leakage current until −V_z, then a near-vertical rise.

  • In breakdown the voltage stays almost fixed at V_z over a wide range of current. That is why it regulates.

  • Maximum safe current: I_z,max = P_z,max/V_z.

  • Regulator circuit: series resistor R_s, then the Zener (reverse biased) in parallel with the load R_L.

  • First check the Zener is on: V_in × R_L/(R_s + R_L) must exceed V_z.

  • When on: V_L = V_z, I_s = (V_in − V_z)/R_s, I_L = V_z/R_L, I_z = I_s − I_L.

  • If V_in rises, I_s and I_z rise; the extra voltage drops across R_s and V_L stays at V_z.

  • If R_L falls, I_L rises and I_z falls by the same amount; I_s does not change.

  • Regulation fails if I_z drops to zero or rises above I_z,max.

  • Zener power P_z = V_z × I_z; the minimum safe R_s = (V_in,max − V_z)/I_z,max (with no load).

  • In forward bias a Zener behaves like an ordinary diode (about 0.7 V for Si).

Must-remember table

QuantityFormulaUnit
Zener-on checkV_in R_L/(R_s + R_L) greater than V_zV
Series currentI_s = (V_in − V_z)/R_sA
Load currentI_L = V_z/R_LA
Zener currentI_z = I_s − I_LA
Zener powerP_z = V_z I_zW
Maximum Zener currentI_z,max = P_z,max/V_zA
Minimum series resistorR_s,min = (V_in,max − V_z)/I_z,maxΩ
Dynamic resistance in breakdownr_z = ΔV/ΔI (a few ohms)Ω

Memory aids

  • "S = Z + L": Supply current splits into Zener current and Load current.

  • "Heavy, Thin, Zener; Light, Wide, Avalanche": doping, depletion width and the breakdown type go together.

  • "Check before you calc": always test V_in R_L/(R_s + R_L) against V_z first.

  • "Load grabs, Zener gives": when the load takes more current, the Zener takes less; I_s stays the same.

  • "Zener sits backwards": in a regulator the Zener's p side goes to the negative rail.

Concept connections

  • Series and parallel resistors and Kirchhoff's current law at the regulator node come from Physics Book 12: Current Electricity.

  • Breakdown fields of the order of 10⁷ to 10⁸ V m⁻¹ link to field and potential ideas in Physics Book 11: Electrostatics.

  • The Zener regulator follows the rectifier and filter in a power supply, and that supply starts from mains ac and a transformer, covered in Physics Book 14: Electromagnetic Induction and Alternating Currents.

Practice MCQs: Chapter 5, Level 4 (new NEET pattern)

31. Match List I with List II.

  • List I: A. Zener breakdown · B. Avalanche breakdown · C. Zener in a regulator · D. Series resistor in a regulator

  • List II: i. drops the extra voltage V_in − V_z · ii. heavy doping, thin depletion region, field pulls electrons out · iii. reverse biased in breakdown · iv. light doping, carriers multiply by collisions

(a) A-iv, B-ii, C-iii, D-i (b) A-ii, B-iv, C-i, D-iii (c) A-ii, B-iv, C-iii, D-i (d) A-iii, B-iv, C-ii, D-i

32. A regulator has V_z = 6 V, V_in = 12 V, R_s = 100 Ω and R_L = 150 Ω. Match List I with List II.

  • List I: A. I_s · B. I_L · C. I_z · D. Zener power

  • List II: i. 0.12 W · ii. 40 mA · iii. 60 mA · iv. 20 mA

(a) A-ii, B-iii, C-iv, D-i (b) A-iii, B-ii, C-iv, D-i (c) A-iii, B-iv, C-ii, D-i (d) A-iv, B-ii, C-iii, D-i

33. Match each region of a silicon Zener's I-V curve (List I) with its behaviour (List II).

  • List I: A. Forward bias above about 0.7 V · B. Reverse bias below V_z · C. Reverse bias at V_z · D. Reverse current above I_z,max

  • List II: i. current rises sharply while voltage stays nearly constant · ii. conducts like an ordinary diode · iii. diode overheats and may be damaged · iv. only a tiny leakage current

(a) A-ii, B-iv, C-i, D-iii (b) A-iv, B-ii, C-i, D-iii (c) A-ii, B-i, C-iv, D-iii (d) A-ii, B-iv, C-iii, D-i

34. Each combination (List I) carries a small current in the stated direction. Match it with the voltage across it (List II). Take 0.7 V for a forward silicon junction.

  • List I: A. Two 5 V Zeners in series, both in reverse breakdown · B. A 5 V Zener in breakdown in series with a forward silicon diode · C. A 5 V Zener in forward bias · D. A 5 V and an 8 V Zener in parallel, both reverse biased

  • List II: i. 0.7 V · ii. 5 V · iii. 5.7 V · iv. 10 V

(a) A-iii, B-iv, C-i, D-ii (b) A-iv, B-iii, C-ii, D-i (c) A-i, B-iii, C-iv, D-ii (d) A-iv, B-iii, C-i, D-ii

35. How many of the following statements are correct?

  • A. Zener breakdown occurs in heavily doped diodes with a low breakdown voltage.

  • B. Avalanche breakdown occurs in lightly doped diodes.

  • C. In breakdown, the Zener current stays fixed while its voltage changes widely.

  • D. A Zener gives a steady V_z when used in forward bias.

(a) one (b) two (c) three (d) four

36. In a working Zener regulator, V_in rises while R_L stays the same. Choose the correct set of statements.

  • A. I_s increases.

  • B. I_z increases.

  • C. I_L increases.

  • D. The voltage across R_s increases.

(a) A, B and D only (b) A and C only (c) B and C only (d) A, B, C and D

37. In a working Zener regulator, R_L is reduced while V_in stays the same. How many of the following statements are correct?

  • A. I_L increases.

  • B. I_z decreases.

  • C. I_s changes greatly.

  • D. If I_z falls to zero, regulation is lost.

(a) one (b) two (c) three (d) four

38. Choose the correct set of statements.

  • A. A Zener diode is heavily doped on both sides.

  • B. The depletion region of a Zener diode is wide.

  • C. Zener diodes are normally used as rectifiers.

  • D. A Zener diode has a sharp breakdown.

(a) A and B only (b) B and C only (c) A, C and D only (d) A and D only

39. Reverse readings of a Zener diode are given.

Reverse voltage (V)268.18.28.3
Reverse current0.01 µA0.02 µA1 mA20 mA40 mA

The dynamic resistance between 20 mA and 40 mA is

(a) 2.5 Ω (b) 5 Ω (c) 205 Ω (d) 410 Ω

40. A 5 V Zener regulator has R_s = 50 Ω and R_L = 100 Ω. It is tested at three inputs.

V_in (V)7911

Which input fails to switch the Zener on, and what is I_z at 11 V?

(a) 9 V fails; 120 mA (b) 7 V fails; 120 mA (c) 7 V fails; 70 mA (d) none fail; 70 mA

41. A 5 V Zener is rated 0.5 W. With no load and V_in = 15 V, the smallest safe series resistor is

(a) 30 Ω (b) 50 Ω (c) 150 Ω (d) 100 Ω

Case for Q42–43. A small charger in Kochi gets a rectified supply that varies from 10 V to 14 V. It uses a 6 V Zener, R_s = 80 Ω and a load of 200 Ω.

42. The smallest Zener current (at 10 V input) is

(a) 20 mA (b) 30 mA (c) 50 mA (d) 70 mA

43. The largest power the Zener must handle (at 14 V input) is

(a) 0.60 W (b) 0.42 W (c) 0.18 W (d) 1.4 W

44. A 4 V Zener and a 6 V Zener are in series, both in reverse breakdown, with R_s = 250 Ω across a 15 V supply. There is no load. The power in the 6 V Zener is

(a) 0.08 W (b) 0.20 W (c) 0.36 W (d) 0.12 W

45. A regulator has V_in = 12 V, V_z = 5 V and R_s = 70 Ω. The Zener needs at least 10 mA to stay in breakdown. The smallest load resistance that keeps regulation is about

(a) 56 Ω (b) 50 Ω (c) 71 Ω (d) 120 Ω

Level 4 answer key

QAnsReason
31cZener: heavy doping, field emission; avalanche: collisions; Zener is reverse biased; R_s drops V_in − V_z
32bCheck: 12 × 150/250 = 7.2 V > 6 V. I_s = 6/100 = 60 mA; I_L = 6/150 = 40 mA; I_z = 20 mA; P = 6 × 0.02 = 0.12 W
33aForward like a diode, leakage below V_z, sharp rise at V_z, damage above I_z,max
34d5 + 5 = 10 V; 5 + 0.7 = 5.7 V; forward Zener 0.7 V; in parallel the 5 V Zener breaks down first and holds 5 V
35bA and B true; voltage stays fixed, current varies (C false); forward bias gives only about 0.7 V (D false)
36aV_L stays V_z, so I_L is unchanged (C false); the extra current goes into the Zener
37cI_s = (V_in − V_z)/R_s does not change (C false)
38dHeavy doping makes the depletion region thin (B false); rectifiers use ordinary diodes (C false)
39br_z = (8.3 − 8.2)/(0.040 − 0.020) = 0.1/0.02 = 5 Ω
40cAt 7 V: 7 × 100/150 = 4.67 V < 5 V, off. At 11 V: I_s = 6/50 = 120 mA, I_L = 50 mA, I_z = 70 mA
41dI_z,max = 0.5/5 = 0.1 A; R_s = (15 − 5)/0.1 = 100 Ω
42aI_s = 4/80 = 50 mA; I_L = 6/200 = 30 mA; I_z = 20 mA
43bI_s = 8/80 = 100 mA; I_z = 70 mA; P = 6 × 0.07 = 0.42 W
44dI = (15 − 10)/250 = 20 mA; P = 6 × 0.02 = 0.12 W
45aI_s = 7/70 = 100 mA; I_L,max = 90 mA; R_L = 5/0.09 ≈ 56 Ω; (b) forgets the 10 mA
23 min left
‹
›