Chapter 5 of 10 · 23 min read

Chapter 3: Diode as a Rectifier

What you will learn

  • Why a diode can turn alternating current into one-way current.

  • How the half-wave rectifier works, with its output waveform and frequency.

  • How the centre-tap full-wave rectifier works, and why its output frequency doubles.

  • Peak, average (dc) and rms values of rectified output, and peak inverse voltage.

  • How a capacitor filter smooths the output, and what ripple means.

3.1 Why rectify?

The mains supply in Indian homes is about 220 V rms at 50 Hz. Its direction reverses 100 times every second. A mobile charger, an LED bulb's driver or a radio needs steady one-way (dc) voltage at a few volts.

So a power supply does three jobs:

  1. A transformer steps 220 V down to a small ac voltage.

  2. A rectifier lets current through in one direction only.

  3. A filter smooths the bumps.

A diode does job 2. It conducts when forward biased and blocks when reverse biased. For rectifier problems we usually treat it as ideal unless a knee voltage is given.

If the secondary rms voltage is V_rms, its peak is:

Vm=2 VrmsV_m = \sqrt{2}\, V_{rms}

3.2 Half-wave rectifier

Circuit. The transformer secondary, one diode and the load resistor R_L are in series.

Working.

  • Positive half cycle: end A of the secondary is positive. The diode is forward biased and conducts. Current flows through R_L and the output follows the input.

  • Negative half cycle: end A is negative. The diode is reverse biased and blocks. No current flows and the output is zero.

Figure 3.1 · Half-wave rectifier circuit with input and output waveforms
Figure 3.1 · Half-wave rectifier circuit with input and output waveforms

The diode conducts only while end A is positive, so the load sees one half-sine pulse per cycle and zero in between.

The output is a train of positive half-sine pulses with gaps between them. It is one-way, but far from steady. We call it pulsating dc.

Output frequency. One pulse comes per input cycle. So the output repeats at the input frequency: 50 Hz for 50 Hz mains.

Peak inverse voltage (PIV). In the negative half, the full reverse voltage of the secondary appears across the diode. The diode must survive a reverse voltage of V_m.

Average (dc) value. Over one period T, the output is V_m sin ωt for half the time and zero for the other half:

Vdc=1T∫0T/2Vmsin⁡ωt dt=VmωT[−cos⁡ωt]0T/2=Vm2π(1+1)=VmπV_{dc} = \frac{1}{T}\int_0^{T/2} V_m \sin \omega t \, dt = \frac{V_m}{\omega T}\Big[-\cos \omega t\Big]_0^{T/2} = \frac{V_m}{2\pi}(1+1) = \frac{V_m}{\pi}

rms value. The mean of V_m² sin² ωt over a half cycle is V_m²/2. Over a full cycle with one half empty, the mean square is V_m²/4. So:

Vrms=Vm2V_{rms} = \frac{V_m}{2}

The half-wave rectifier wastes the whole negative half. That is its main weakness.

Worked example 3.1: Mains at 220 V rms, 50 Hz, feeds a step-down transformer with turns ratio 10 : 1. The secondary drives a half-wave rectifier with an ideal diode. Find the peak output, the dc output and the output frequency.

Solution: Secondary rms = 220/10 = 22 V. Peak V_m = 22 × 1.414 ≈ 31.1 V.

Vdc=Vmπ=31.13.14≈9.9 VV_{dc} = \frac{V_m}{\pi} = \frac{31.1}{3.14} \approx 9.9\ \text{V}

Output frequency = 50 Hz.

Worked example 3.2: A half-wave rectifier uses a silicon diode (0.7 V). The input peak is 10 V and the load is 1 kΩ. Find the peak output voltage and the peak load current.

Solution: While conducting, the diode takes 0.7 V. Peak output = 10 − 0.7 = 9.3 V. Peak current = 9.3/1000 = 9.3 mA.

3.3 Full-wave rectifier (centre-tap)

Circuit. The transformer secondary has a centre tap C. The two ends A and B each feed a diode, D1 and D2. Both diode outputs join at one end of R_L. The other end of R_L goes to C.

The voltages of A and B, measured from C, are always equal and opposite.

Working.

  • Positive half cycle: A is positive and B negative (with respect to C). D1 conducts, D2 blocks. Current flows through R_L from top to bottom.

  • Negative half cycle: B is positive and A negative. D2 conducts, D1 blocks. Current again flows through R_L from top to bottom.

So both halves give an output pulse in the same direction.

Figure 3.2 · Centre-tap full-wave rectifier with input and output waveforms
Figure 3.2 · Centre-tap full-wave rectifier with input and output waveforms

D1 conducts in one half cycle and D2 in the other, both sending current the same way through R_L, so the output has two pulses per input cycle.

Output frequency. Two pulses come per input cycle. The output repeats at twice the input frequency: 100 Hz for 50 Hz mains.

Average and rms values. The output is like two half-wave outputs placed back to back:

Vdc=2Vmπ,Vrms=Vm2V_{dc} = \frac{2V_m}{\pi}, \qquad V_{rms} = \frac{V_m}{\sqrt{2}}

Here V_m is the peak voltage of each half of the secondary (from the centre tap to one end).

PIV. When D1 is off, its cathode sits at +V_m (through the conducting D2 and the load), and its anode at −V_m. So each diode must withstand 2V_m in a centre-tap rectifier.

Bridge rectifier (for awareness). Four diodes arranged in a bridge give full-wave output without a centre tap. Two diodes conduct in each half, so with silicon diodes the output peak is V_m − 1.4 V. Each diode faces a PIV of V_m.

FeatureHalf-waveFull-wave (centre-tap)
Diodes12
Halves usedOneBoth
Output frequency (50 Hz input)50 Hz100 Hz
V_dcV_m/π ≈ 0.318 V_m2V_m/π ≈ 0.637 V_m
V_rmsV_m/2V_m/√2
PIV per diodeV_m2V_m
Ripple factorabout 1.21about 0.48
Maximum efficiencyabout 40.6%about 81.2%

Worked example 3.3: A centre-tap transformer gives 12 V rms from the centre tap to each end. With ideal diodes, find V_dc and the PIV of each diode.

Solution: V_m = 12 × 1.414 ≈ 16.97 V.

Vdc=2×16.97π≈10.8 V,PIV=2Vm≈33.9 VV_{dc} = \frac{2 \times 16.97}{\pi} \approx 10.8\ \text{V}, \qquad \text{PIV} = 2V_m \approx 33.9\ \text{V}

Worked example 3.4: The input to a rectifier is v = 20 sin(100πt) volt. Find the output frequency and the dc output for (i) a half-wave and (ii) a full-wave rectifier, using ideal diodes. For (ii) take 20 V as the peak of each half.

Solution: ω = 100π, so input f = 50 Hz.

  • Half-wave: output 50 Hz, V_dc = 20/π ≈ 6.37 V.

  • Full-wave: output 100 Hz, V_dc = 40/π ≈ 12.7 V.

3.4 Ripple and the capacitor filter

Rectified output still rises and falls. The ac part riding on the dc level is called ripple. A measure of it is the ripple factor:

r=Vac, rmsVdcr = \frac{V_{ac,\,rms}}{V_{dc}}

Half-wave gives r ≈ 1.21, full-wave r ≈ 0.48. Smaller is better.

Capacitor filter. Put a large capacitor C in parallel with R_L.

  1. As the output rises, the capacitor charges quickly through the diode, up to nearly V_m.

  2. As the input falls below the capacitor voltage, the diode turns off.

  3. The capacitor now discharges slowly through R_L, with time constant R_L C.

  4. Before it falls far, the next pulse arrives and tops it up.

The result is a nearly flat voltage close to V_m with a small saw-tooth ripple. Think of a water tank on the roof: the municipal supply comes in bursts, but the tap below runs steadily.

For good smoothing, the time constant must be much longer than the time between pulses:

RLC≫1frR_L C \gg \frac{1}{f_r}

Here f_r is the ripple frequency (f for half-wave, 2f for full-wave). A useful estimate of the peak-to-peak ripple, when R_L C is large, is:

ΔV≈VmfrRLC\Delta V \approx \frac{V_m}{f_r R_L C}

So ripple falls when C or R_L rises, and a full-wave rectifier (higher f_r) is easier to smooth. A heavier load (smaller R_L) means more ripple.

Worked example 3.5: A full-wave rectifier on 50 Hz mains has V_m = 15 V, R_L = 500 Ω and C = 1000 μF. Estimate the ripple.

Solution: f_r = 100 Hz and R_L C = 500 × 10⁻³ = 0.5 s, much longer than 0.01 s.

ΔV≈15100×0.5=0.3 V\Delta V \approx \frac{15}{100 \times 0.5} = 0.3\ \text{V}

Worked example 3.6: A half-wave rectifier on 50 Hz feeds a 1 kΩ load. The designer wants R_L C to be at least 10 times the ripple period. Find the least capacitance.

Solution: Ripple period = 1/50 = 0.02 s. Need R_L C ≥ 0.2 s. So C ≥ 0.2/1000 = 2 × 10⁻⁴ F = 200 μF.

Worked example 3.7 (NEET-hard): A half-wave rectifier with a silicon diode (0.7 V) is fed by v = 20 sin ωt volt. For what fraction of each cycle does the diode conduct?

Solution: The diode conducts while the input exceeds 0.7 V. So it starts at sin θ = 0.7/20 = 0.035, θ ≈ 2.0°, and stops at 180° − 2.0° = 178.0°.

fraction=178.0−2.0360≈0.489\text{fraction} = \frac{178.0 - 2.0}{360} \approx 0.489

So about 48.9% of the time, slightly less than half.

Quick revision

  • Diode conducts one way only, so it rectifies ac.

  • Half-wave: 1 diode, output at f, V_dc = V_m/π, V_rms = V_m/2, PIV = V_m.

  • Full-wave centre-tap: 2 diodes, output at 2f, V_dc = 2V_m/π, V_rms = V_m/√2, PIV = 2V_m.

  • Bridge: 4 diodes, two conduct at a time, PIV = V_m.

  • Output without a filter is pulsating dc.

  • Capacitor in parallel with load smooths output; need R_L C much greater than 1/f_r.

  • Ripple ΔV ≈ V_m/(f_r R_L C): larger C or R_L, less ripple.

NEET traps

  • Saying full-wave output frequency equals input frequency. It is double.

  • Using rms in place of peak. Convert with V_m = √2 V_rms first.

  • Putting the filter capacitor in series with the load. It goes in parallel.

  • Forgetting that a centre-tap diode faces PIV of 2V_m, not V_m.

  • In a bridge rectifier with Si diodes, subtracting only 0.7 V; two diodes conduct, so subtract 1.4 V.

  • Thinking the output of a rectifier is pure dc without a filter.

Practice MCQs: Chapter 3

Level 1: Concept check

1. A rectifier converts (a) ac into pulsating dc (b) dc into ac (c) low ac voltage into high ac voltage (d) dc into higher dc

2. In a half-wave rectifier, the output during the negative half cycle of the input is (a) equal to the input (b) inverted (c) zero (d) doubled

3. The number of diodes in a centre-tap full-wave rectifier is (a) 1 (b) 2 (c) 3 (d) 4

4. For 50 Hz input, the output frequency of a full-wave rectifier is (a) 25 Hz (b) 50 Hz (c) 0 Hz (d) 100 Hz

5. In a capacitor filter, the capacitor is connected (a) in series with the load (b) in parallel with the load (c) in series with the diode only (d) across the primary of the transformer

6. The output of a rectifier without any filter is (a) pure dc (b) pure ac (c) pulsating dc (d) square wave ac

7. In a centre-tap full-wave rectifier, the two diodes (a) conduct together in each half cycle (b) never conduct (c) conduct only in the positive half (d) conduct alternately, one in each half cycle

8. With the load fixed, increasing the filter capacitance makes the ripple (a) smaller (b) larger (c) unchanged (d) first larger then smaller

9. For 60 Hz input, the output frequency of a half-wave rectifier is (a) 30 Hz (b) 60 Hz (c) 120 Hz (d) 0 Hz

10. A bridge rectifier uses (a) 1 diode (b) 2 diodes (c) 4 diodes (d) 6 diodes

Level 2: NEET standard

11. A half-wave rectifier with an ideal diode has input peak 12 V. Its dc output is about (a) 6.0 V (b) 8.5 V (c) 7.6 V (d) 3.8 V

12. A full-wave rectifier with ideal diodes has 11 V peak from the centre tap to each end. Its dc output is about (a) 3.5 V (b) 7.0 V (c) 7.8 V (d) 11 V

13. 220 V rms mains feeds a step-down transformer of turns ratio 11 : 1, then a half-wave rectifier with an ideal diode. The peak output is about (a) 28.3 V (b) 20 V (c) 14.1 V (d) 40 V

14. A half-wave rectifier with a silicon diode (0.7 V) has input peak 5 V and load 430 Ω. The peak load current is (a) 11.6 mA (b) 8.4 mA (c) 10 mA (d) 1.6 mA

15. In a centre-tap rectifier, the peak voltage from the centre tap to each end is 10 V. The peak inverse voltage on each diode is (a) 5 V (b) 10 V (c) 14.1 V (d) 20 V

16. A half-wave rectifier is fed with 7.07 V rms. The peak inverse voltage on the ideal diode is about (a) 7.07 V (b) 10 V (c) 14.1 V (d) 20 V

17. The peak output of a half-wave rectifier is 18 V. The rms value of the output is (a) 9 V (b) 12.7 V (c) 5.7 V (d) 18 V

18. A full-wave rectifier runs on 60 Hz mains. The ripple frequency is (a) 30 Hz (b) 60 Hz (c) 120 Hz (d) 240 Hz

19. In an ideal half-wave rectifier, the diode conducts for (a) the whole cycle (b) one quarter of the cycle (c) three quarters of the cycle (d) half of the cycle

20. A full-wave rectifier on 50 Hz feeds a 2 kΩ load. For R_L C to be at least 10 times the ripple period, the least capacitance is (a) 100 μF (b) 50 μF (c) 25 μF (d) 500 μF

21. A full-wave rectifier on 50 Hz has V_m = 12 V, R_L = 600 Ω and C = 2000 μF. The estimated ripple is about (a) 0.1 V (b) 0.2 V (c) 1.0 V (d) 0.05 V

22. In a centre-tap full-wave rectifier on 50 Hz mains, one diode burns out and becomes an open circuit. The output now (a) becomes zero (b) becomes pure dc (c) is half-wave with frequency 50 Hz (d) is full-wave with frequency 100 Hz

Level 3: Challenge

23. The input to a half-wave rectifier is v = 30 sin(200πt) volt. With an ideal diode, the dc output and the output frequency are (a) 19.1 V, 200 Hz (b) 9.55 V, 100 Hz (c) 9.55 V, 200 Hz (d) 19.1 V, 100 Hz

24. For the same peak voltage V_m, the ratio of dc output of a full-wave rectifier to that of a half-wave rectifier is (a) 1/2 (b) 1 (c) √2 (d) 2

25. A half-wave rectifier with a silicon diode (0.7 V) is fed by v = 10 sin ωt volt. The diode conducts for about what fraction of each cycle? (a) 50% (b) 45.1% (c) 47.8% (d) 46.5%

26. A centre-tap transformer gives 30 V rms from end to end. With silicon diodes (0.7 V), the peak output of the full-wave rectifier is about (a) 20.5 V (b) 41.7 V (c) 21.2 V (d) 14.3 V

27. A bridge rectifier with silicon diodes (0.7 V each) is fed from 12 V rms. The peak output voltage is about (a) 17.0 V (b) 16.3 V (c) 10.6 V (d) 15.6 V

28. A half-wave rectifier on 50 Hz has V_m = 20 V, R_L = 1 kΩ and C = 500 μF. The estimated ripple is about (a) 0.4 V (b) 0.8 V (c) 1.6 V (d) 8 V

29. Assertion (A): The output frequency of a full-wave rectifier is twice the input frequency. Reason (R): In a full-wave rectifier, both half cycles of the input give output pulses in the same direction. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: The output of a capacitor filter approaches the peak value V_m when R_L C is much larger than the ripple period. Statement II: In a half-wave rectifier, the peak inverse voltage across the diode is 2V_m. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1aA rectifier gives one-way (pulsating dc) output from ac.
2cThe diode is reverse biased and blocks.
3bOne diode per half of the secondary.
4dTwo pulses per cycle: 2 × 50 = 100 Hz.
5bThe capacitor sits across the load to store and release charge.
6cOne-way but varying output.
7dD1 conducts in one half, D2 in the other.
8aΔV ≈ V_m/(f_r R_L C) falls as C rises.
9bOne pulse per input cycle.
10cFour diodes form the bridge.
11dV_dc = 12/π ≈ 3.8 V.
12bV_dc = 2 × 11/π ≈ 7.0 V.
13aSecondary 20 V rms, peak 20√2 ≈ 28.3 V.
14c(5 − 0.7)/430 = 10 mA.
15dCentre-tap PIV = 2V_m = 20 V.
16bV_m = 1.414 × 7.07 ≈ 10 V = PIV.
17aHalf-wave V_rms = V_m/2 = 9 V.
18cFull-wave ripple at 2f = 120 Hz.
19dOnly the positive half conducts.
20bPeriod 0.01 s; R_L C ≥ 0.1 s; C ≥ 0.1/2000 = 50 μF.
21aΔV ≈ 12/(100 × 600 × 0.002) = 0.1 V.
22cOnly one diode works, so it acts as a half-wave rectifier.
23bf = 100 Hz; V_dc = 30/π ≈ 9.55 V.
24d(2V_m/π)/(V_m/π) = 2.
25csin θ = 0.07, θ ≈ 4.0°; (180 − 8.0)/360 ≈ 47.8%.
26aEach half 15 V rms, V_m ≈ 21.2 V; 21.2 − 0.7 ≈ 20.5 V.
27dV_m ≈ 16.97 V; two diodes drop 1.4 V: about 15.6 V.
28bΔV ≈ 20/(50 × 1000 × 5 × 10⁻⁴) = 0.8 V.
29aSame-direction pulses in both halves double the frequency.
30cHalf-wave PIV is V_m, not 2V_m.

Chapter 3 revision sheet

One-page summary

  • A rectifier turns ac into pulsating dc because a diode conducts in one direction only.

  • Peak of a sine supply: V_m = √2 × V_rms (230 V rms mains has V_m ≈ 325 V).

  • Half-wave: one diode, conducts only in the positive half cycle; output frequency = f.

  • Half-wave: V_dc = V_m/π, V_rms = V_m/2, PIV = V_m, ripple factor 1.21, maximum efficiency 40.6%.

  • Centre-tap full-wave: two diodes take turns, each for one half cycle; needs a centre-tapped secondary.

  • Full-wave: output frequency = 2f, V_dc = 2V_m/π, V_rms = V_m/√2, ripple factor 0.48, maximum efficiency 81.2%.

  • Centre-tap PIV = 2V_m (V_m = peak of each half of the secondary).

  • Bridge: four diodes, two conduct in each half cycle, no centre tap needed, PIV = V_m.

  • With real Si diodes, a bridge loses about 1.4 V (two diodes) from each peak; half-wave and centre-tap lose about 0.7 V.

  • Ripple factor r = (rms of ac part)/(dc value); smaller r means smoother dc.

  • A capacitor across the load charges near each peak and discharges slowly through R_L between peaks.

  • Good smoothing needs R_L C much greater than 1/f_r, where f_r is the ripple frequency.

  • Ripple voltage ΔV ≈ V_m/(f_r R_L C): larger C, larger R_L or higher f_r give less ripple.

  • With a capacitor filter, each diode conducts only for a short time near the peak.

Must-remember table

QuantityHalf-waveCentre-tap full-waveBridge
Diodes124
Output frequencyf2f2f
V_dcV_m/π2V_m/π2V_m/π
V_rmsV_m/2V_m/√2V_m/√2
PIV per diodeV_m2V_mV_m
Ripple factor1.210.480.48
Maximum efficiency40.6%81.2%81.2%

Memory aids

  • "Half keeps, Full doubles": half-wave output keeps the input frequency f; full-wave doubles it to 2f.

  • "1-2-4": one diode for half-wave, two for centre-tap, four for bridge.

  • "One pi alone, two pi together": V_dc is V_m/π for half-wave and 2V_m/π for full-wave.

  • "Centre-tap carries the double load": centre-tap diodes face PIV 2V_m; the other two types face V_m.

  • "Efficiency doubles, ripple drops": 40.6% becomes 81.2%; 1.21 falls to 0.48.

Concept connections

  • Peak, rms and average values of a sine wave, and transformers, come from Physics Book 14: Electromagnetic Induction and Alternating Currents.

  • Capacitor charging and discharging through a resistor (time constant RC) comes from Physics Book 11: Electrostatics.

  • Power P = V²/R and Ohm's law for the load come from Physics Book 12: Current Electricity.

Practice MCQs: Chapter 3, Level 4 (new NEET pattern)

31. The input is 50 Hz ac. Match List I with List II.

  • List I: A. Output frequency of a half-wave rectifier · B. Output frequency of a full-wave rectifier · C. Ripple factor of a half-wave rectifier · D. Maximum efficiency of a full-wave rectifier

  • List II: i. 1.21 · ii. 100 Hz · iii. 81.2% · iv. 50 Hz

(a) A-ii, B-iv, C-i, D-iii (b) A-iv, B-ii, C-iii, D-i (c) A-iv, B-i, C-ii, D-iii (d) A-iv, B-ii, C-i, D-iii

32. Match List I with List II (V_m is the peak input to the diode).

  • List I: A. V_dc of half-wave · B. V_dc of full-wave · C. V_rms of half-wave · D. V_rms of full-wave

  • List II: i. V_m/π · ii. V_m/2 · iii. 2V_m/π · iv. V_m/√2

(a) A-i, B-iii, C-ii, D-iv (b) A-iii, B-i, C-ii, D-iv (c) A-i, B-iii, C-iv, D-ii (d) A-ii, B-iii, C-i, D-iv

33. With ideal diodes and V_m = 20 V, match List I with List II.

  • List I: A. V_dc of half-wave · B. V_dc of full-wave · C. V_rms of half-wave · D. V_rms of full-wave

  • List II: i. 10 V · ii. 6.37 V · iii. 14.1 V · iv. 12.7 V

(a) A-iv, B-ii, C-i, D-iii (b) A-ii, B-iv, C-iii, D-i (c) A-ii, B-iv, C-i, D-iii (d) A-i, B-iv, C-ii, D-iii

34. Match List I with List II.

  • List I: A. Half-wave rectifier · B. Centre-tap full-wave rectifier · C. Bridge rectifier · D. Capacitor filter

  • List II: i. one diode, output at input frequency · ii. charges near each peak, discharges slowly through the load · iii. four diodes, no centre tap · iv. two diodes, centre-tapped secondary

(a) A-i, B-iii, C-iv, D-ii (b) A-i, B-iv, C-iii, D-ii (c) A-iv, B-i, C-iii, D-ii (d) A-ii, B-iv, C-iii, D-i

35. How many of the following statements are correct?

  • A. In a bridge rectifier, two diodes conduct in each half cycle.

  • B. In a centre-tap rectifier, each diode conducts for half of every cycle.

  • C. The output of a half-wave rectifier has no ac component.

  • D. A larger filter capacitor gives a smaller ripple.

(a) one (b) two (c) three (d) four

36. Choose the correct set of statements (ideal diodes).

  • A. A full-wave rectifier fed from 50 Hz mains has a ripple frequency of 100 Hz.

  • B. The maximum efficiency of a half-wave rectifier is 81.2%.

  • C. Each diode of a bridge rectifier faces a PIV of V_m.

  • D. The rms value of full-wave output equals the rms value of the input sine of the same peak.

(a) A and B only (b) B and C only (c) A and C only (d) A, C and D only

37. Choose the correct set of statements about a capacitor-input filter.

  • A. Good smoothing needs R_L C much greater than 1/f_r.

  • B. Drawing more load current (smaller R_L) increases the ripple.

  • C. With the capacitor, each diode conducts for the whole half cycle.

  • D. The ripple voltage is about V_m/(f_r R_L C).

(a) A, B and D only (b) A and C only (c) B, C and D only (d) A, B, C and D

38. How many of the following statements are correct?

  • A. 230 V rms mains has a peak of about 325 V.

  • B. A 10:1 step-down transformer gives about 23 V rms from 230 V rms mains.

  • C. The dc value of a full-wave rectifier's output is V_m/π.

  • D. A half-wave rectifier uses both half cycles of the input.

(a) one (b) two (c) three (d) four

39. An oscilloscope shows the input as a 50 Hz sine wave. The output across the load is a train of identical positive half-sine humps with no gaps between them, 100 humps every second. The circuit and its ripple frequency are

(a) full-wave rectifier, 100 Hz (b) half-wave rectifier, 50 Hz (c) half-wave rectifier, 100 Hz (d) full-wave rectifier, 50 Hz

40. A full-wave rectifier (f_r = 100 Hz, V_m = 12 V, R_L = 1 kΩ) is tested with three filter capacitors.

C (µF)1004701000
Ripple ΔV (V)1.2?0.12

The missing ripple voltage is about

(a) 2.6 V (b) 0.56 V (c) 0.26 V (d) 0.026 V

41. A bridge rectifier uses silicon diodes (0.7 V each when on). The secondary peak voltage is 15 V. The peak voltage across the load is

(a) 15 V (b) 14.3 V (c) 7.5 V (d) 13.6 V

Case for Q42–43. A mobile-charger kit runs from 230 V rms, 50 Hz mains. A 20:1 step-down transformer feeds a bridge rectifier with ideal diodes and a 1 kΩ load. There is no filter.

42. The dc voltage across the load is about

(a) 16.3 V (b) 10.4 V (c) 5.2 V (d) 11.5 V

43. The dc load current and the output ripple frequency are

(a) 10.4 mA, 100 Hz (b) 10.4 mA, 50 Hz (c) 16.3 mA, 100 Hz (d) 5.2 mA, 50 Hz

44. An ideal half-wave rectifier has V_m = 50 V and R_L = 1 kΩ. The dc power delivered to the load is about

(a) 1.25 W (b) 0.63 W (c) 0.50 W (d) 0.25 W

45. A full-wave rectifier runs on 50 Hz with R_L = 2 kΩ. The ripple voltage must be at most 2% of V_m. Using ΔV ≈ V_m/(f_r R_L C), the smallest filter capacitor is

(a) 25 µF (b) 125 µF (c) 250 µF (d) 500 µF

Level 4 answer key

QAnsReason
31dHalf-wave keeps 50 Hz, full-wave gives 100 Hz; half-wave ripple 1.21; full-wave efficiency 81.2%
32aV_m/π and V_m/2 for half-wave; 2V_m/π and V_m/√2 for full-wave
33c20/π = 6.37 V; 40/π = 12.7 V; 20/2 = 10 V; 20/√2 = 14.1 V
34bOne diode for half-wave, two with centre tap, four in a bridge; the capacitor stores charge near peaks
35cA, B, D true; half-wave output is strongly pulsating, so it has a large ac part (C false)
36dHalf-wave maximum efficiency is 40.6% (B false); full-wave V_rms = V_m/√2, same as the input
37aThe diode conducts only briefly near each peak (C false)
38bA and B true (230√2 ≈ 325 V); full-wave V_dc = 2V_m/π; half-wave uses one half only
39aHumps every half cycle mean full-wave; 2 × 50 = 100 Hz
40cΔV = 12/(100 × 1000 × 470 × 10⁻⁶) ≈ 0.26 V
41dTwo diodes conduct in series: 15 − 1.4 = 13.6 V
42bSecondary 11.5 V rms, V_m = 11.5√2 ≈ 16.3 V, V_dc = 2V_m/π ≈ 10.4 V
43aI_dc = 10.4 V/1 kΩ = 10.4 mA; bridge output is at 2 × 50 = 100 Hz
44dV_dc = 50/π ≈ 15.9 V; P = V_dc²/R = 0.25 W; (b) uses V_rms = 25 V
45c1/(f_r R_L C) ≤ 0.02 with f_r = 100 Hz: C ≥ 1/(100 × 2000 × 0.02) = 250 µF; (d) wrongly uses 50 Hz
23 min left
‹
›
Chapter 3: Diode as a | NEET Physics Book 19: Electronic…