Last-Week Revision Kit
Use this kit in the final week: read the sheet, test yourself on the facts, tick the checklist, then sit Mock Test 2 against the clock.
Book-at-a-glance sheet
Chapters 1–3: current, resistance, temperature
| Chapter | Key formula or fact | Remember |
|---|---|---|
| 1 | I = dq/dt, I = qf | 1.6 A = 10¹⁹ electrons per second |
| 1 | I = neAv_d | v_d ∝ 1/A for the same current |
| 1 | v_d = eEτ/m, μ = eτ/m | v_d ~ 10⁻⁴ m/s, τ ~ 10⁻¹⁴ s |
| 1 | J = σE, σ = ne²τ/m | J is a vector, I is a scalar |
| 2 | V = IR, R = ρL/A | ρ depends on material and temperature only |
| 2 | Stretch n times: n²R; radius 1/k: k⁴R | Small stretch x% raises R by 2x% |
| 2 | Colour code 0–9 | Gold ±5%, silver ±10%, none ±20% |
| 3 | R = R_0(1 + αΔT) | Metals α positive, semiconductors α negative |
| 3 | Zero-drift series pair: R_1α_1 + R_2α_2 = 0 | Manganin, constantan: tiny α |
Chapters 4–5: combinations and cells
| Chapter | Key formula or fact | Remember |
|---|---|---|
| 4 | Series ΣR, parallel 1/R = Σ(1/R) | n equal: ratio series/parallel = n² |
| 4 | Two in parallel R_1R_2/(R_1 + R_2) | Current divides inversely as R |
| 4 | Ring R_0x(1 − x); cube 5r/6, 3r/4, 7r/12 | Use symmetry before Kirchhoff |
| 5 | I = E/(R + r), V = E − Ir | Charging: V = E + Ir |
| 5 | Short-circuit current E/r | Open circuit V = E |
| 5 | Mixed grouping mnE/(mR + nr) | Max current when R = nr/m |
| 5 | P_max = E²/4r at R = r | Efficiency 50% at maximum power |
Chapters 6–8: power, Kirchhoff, bridges
| Chapter | Key formula or fact | Remember |
|---|---|---|
| 6 | P = VI = I²R = V²/R, H = I²Rt | 1 kWh = 3.6 × 10⁶ J |
| 6 | R = V_r²/P_r, P = P_r(V/V_r)² | Half voltage gives quarter power |
| 6 | Series bulbs: lower watt brighter | Parallel bulbs: higher watt brighter |
| 6 | Coils: series t_1 + t_2; parallel t_1t_2/(t_1 + t_2) | Line loss P²R/V² |
| 7 | ΣI = 0 at a junction | Charge conservation |
| 7 | ΣΔV = 0 round a loop | Energy conservation; −IR with current, +E from − to + |
| 8 | P/Q = R/S | Independent of emf and galvanometer |
| 8 | R/S = l/(100 − l) | Best null point near 50 cm |
40 rapid-fire facts
The SI unit of current, the ampere, is a base unit.
1 A is a flow of 1 coulomb per second.
About 6.25 × 10¹⁸ electrons pass per second in a 1 A current.
Conventional current flows opposite to electron drift.
Current is a scalar even though it has a direction along the wire.
Current density J = I/A is a vector, unit A m⁻².
Copper has about 8.5 × 10²⁸ free electrons per cubic metre.
Drift speed in household wires is of the order of 10⁻⁴ m/s.
Relaxation time in metals is of the order of 10⁻¹⁴ s.
Mobility has the unit m² V⁻¹ s⁻¹.
In a wire of varying thickness, current is the same at every section.
Ohm's law holds only at constant temperature and physical conditions.
Resistivity of copper is about 1.7 × 10⁻⁸ Ω m.
Resistivity of a material does not depend on the length or area of the sample.
Doubling the length of a wire at constant volume makes its resistance 4 times.
Halving the radius of a wire at constant volume makes its resistance 16 times.
A gold fourth band on a resistor means ±5% tolerance.
Grey stands for 8 and violet for 7 in the colour code.
Metals have a positive temperature coefficient of resistance.
Semiconductors have a negative temperature coefficient of resistance.
Manganin and constantan are used in standard resistors because their α is very small.
Nichrome is used in heating elements.
Mercury becomes superconducting near 4.2 K.
Equivalent resistance in parallel is less than the smallest resistance present.
Household appliances are connected in parallel.
Two equal resistors in parallel give half of one resistor.
The emf of a cell equals its terminal voltage on open circuit.
Terminal voltage is less than emf while discharging and more while charging.
The short-circuit current of a cell is E/r.
The V-I graph of a cell has slope −r and y-intercept E.
Maximum power is drawn from a source when the load equals its internal resistance.
Efficiency at maximum power transfer is 50%.
1 kWh equals 3.6 × 10⁶ J.
A 220 V, 100 W bulb has a resistance of 484 Ω.
In series, the bulb with lower rated wattage glows brighter.
Power is transmitted at high voltage to reduce I²R losses.
Kirchhoff's junction rule comes from conservation of charge.
Kirchhoff's loop rule comes from conservation of energy.
A balanced Wheatstone bridge is not affected by the emf of the cell or the galvanometer resistance.
The metre bridge gives the least percentage error when the null point is near the middle of the wire.
Common mistakes checklist
I don't confuse resistance (depends on size) with resistivity (depends only on material and temperature).
I can find the new resistance of a stretched wire by keeping the volume constant.
I don't confuse drift speed (about 10⁻⁴ m/s) with the speed at which the electric signal travels.
I can read a four-band colour code, including the multiplier and tolerance bands.
I don't mix up the sign of α for metals and semiconductors.
I can tell which bulb glows brighter in series and in parallel without calculating.
I don't forget the internal resistance when a question gives r.
I can use V = E + Ir for a cell being charged and V = E − Ir for one discharging.
I can apply Kirchhoff's sign rules and treat a negative current as a reversed direction, not an error.
I check for a balanced bridge before writing long Kirchhoff equations.
Mock Test 2: New-pattern paper
30 questions, all chapters, time 35 minutes. Marking: +4 for a correct answer, −1 for a wrong one, 0 if left blank. For assertion–reason questions use these options: (a) Both A and R are true and R is the correct explanation of A; (b) Both A and R are true but R is not the correct explanation of A; (c) A is true but R is false; (d) A is false but R is true.
1. Match List I (quantity) with List II (SI unit).
List I: A. Conductivity; B. Mobility; C. Current density; D. Temperature coefficient of resistance
List II: (i) K⁻¹; (ii) A m⁻²; (iii) S m⁻¹; (iv) m² V⁻¹ s⁻¹
(a) A-iv, B-iii, C-ii, D-i (b) A-iii, B-iv, C-ii, D-i (c) A-iii, B-ii, C-iv, D-i (d) A-i, B-iv, C-ii, D-iii
2. A 2 m wire of resistance 6 Ω is stretched uniformly to 4 m. Its new resistance is
(a) 12 Ω (b) 6 Ω (c) 24 Ω (d) 48 Ω
3. Assertion (A): When a thick and a thin copper wire of the same length are joined in series, the drift speed is greater in the thin wire. Reason (R): The resistivity of copper does not depend on the dimensions of the wire.
(a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true
4. A cell of emf 6 V and internal resistance 1 Ω is connected to a 5 Ω resistor. Choose the correct set of statements.
A. The current is 1 A.
B. The terminal voltage is 5 V.
C. The power wasted inside the cell is 1 W.
D. The efficiency is 50%.
(a) A and B only (b) A, B and D only (c) C and D only (d) A, B and C only
5. I-V graphs (I on the y-axis, V on the x-axis) of the same metal wire at temperatures T_1 and T_2 are straight lines through the origin. The line for T_1 is steeper. Then
(a) T_1 > T_2 (b) T_1 = T_2 (c) it cannot be decided (d) T_1 < T_2
6. The maximum power a 12 V battery of internal resistance 0.5 Ω can give to an external resistor is
(a) 144 W (b) 36 W (c) 72 W (d) 288 W
Passage for Q7–Q8: A hostel room on a 220 V supply runs a 1100 W room heater for 3 hours every night during a 30-day winter month. Electricity costs Rs 7 per unit.
7. The current drawn by the heater is
(a) 0.2 A (b) 2 A (c) 5 A (d) 10 A
8. The heater's cost for the month is
(a) Rs 231 (b) Rs 99 (c) Rs 462 (d) Rs 693
9. The number of electrons crossing a section of a wire each second when it carries 3.2 A is
(a) 5 × 10¹⁹ (b) 3.2 × 10¹⁹ (c) 2 × 10¹⁹ (d) 2 × 10¹⁸
10. The equivalent resistance of 2 Ω, 3 Ω and 6 Ω in parallel is
(a) 11 Ω (b) 1 Ω (c) 2 Ω (d) 0.5 Ω
11. Match the rating in List I with the resistance in List II.
List I: A. 100 W, 200 V; B. 50 W, 200 V; C. 200 W, 100 V; D. 1000 W, 250 V
List II: (i) 62.5 Ω; (ii) 50 Ω; (iii) 800 Ω; (iv) 400 Ω
(a) A-iii, B-iv, C-ii, D-i (b) A-iv, B-ii, C-iii, D-i (c) A-iv, B-iii, C-ii, D-i (d) A-i, B-iii, C-ii, D-iv
12. In a metre bridge, 12 Ω is in the right gap and the null point is 60 cm from the left end. The resistance in the left gap is
(a) 8 Ω (b) 7.2 Ω (c) 20 Ω (d) 18 Ω
13. A copper coil has resistance 20 Ω at 20 °C. With α = 4 × 10⁻³ per °C (20 °C as reference), its resistance at 70 °C is
(a) 22 Ω (b) 24 Ω (c) 28 Ω (d) 25.6 Ω
14. Assertion (A): When two cells are joined in series in opposition, the net emf is the difference of their emfs. Reason (R): When two cells are in opposition in a loop, both cells always discharge.
(a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true
15. Six 6 Ω resistors form a regular hexagon. The resistance between two opposite corners is
(a) 9 Ω (b) 36 Ω (c) 1 Ω (d) 18 Ω
16. V-I graphs (V on the y-axis) are drawn for two cells. Cell X: a straight line from 6 V at I = 0 to zero at I = 3 A. Cell Y: a straight line from 4 V at I = 0 to zero at I = 4 A. Which is true?
(a) X has the larger emf, Y the larger internal resistance (b) Y has the larger emf and the larger internal resistance (c) X has the larger emf and the larger internal resistance (d) Both have the same internal resistance
17. How many of the following statements are correct?
A. For a given conductor at fixed temperature, drift speed is proportional to the applied field.
B. The resistivity of a metal is inversely proportional to the relaxation time.
C. The SI unit of conductivity is S m⁻¹.
D. In silicon, electrons usually have a higher mobility than holes.
(a) 4 (b) 3 (c) 2 (d) 1
Passage for Q18–Q19: A water heater has two identical coils, each of 55 Ω, and a switch that connects them in series or in parallel across the 220 V mains.
18. The power in the series setting is
(a) 1760 W (b) 880 W (c) 220 W (d) 440 W
19. The power in the parallel setting is
(a) 440 W (b) 880 W (c) 1760 W (d) 3520 W
20. A carbon resistor has bands red, violet, yellow, gold. Its value is
(a) 27 kΩ ± 5% (b) 270 kΩ ± 5% (c) 2.7 MΩ ± 10% (d) 270 kΩ ± 10%
21. Graphs of current density J (y-axis) against field E (x-axis) for metals P and Q at the same temperature are straight lines through the origin. The slope for P is twice that for Q. The ratio of resistivities ρ_P : ρ_Q is
(a) 2 : 1 (b) 1 : 1 (c) 1 : 2 (d) 4 : 1
22. A current of 1 A flows from X to Y through, in order, a 4 Ω resistor, a 10 V cell whose positive terminal faces Y, and a 2 Ω resistor. V_X − V_Y is
(a) 4 V (b) −4 V (c) 16 V (d) −16 V
23. Choose the correct set of statements.
A. The metre-bridge null point does not depend on the emf of the driving cell.
B. A Wheatstone bridge is balanced when the two ends of the galvanometer are at the same potential.
C. Changing the galvanometer for one of higher resistance changes the balance length.
D. The metre-bridge wire is usually made of manganin or constantan.
(a) A and C only (b) B and C only (c) A, B and C only (d) A, B and D only
24. Five cells, each 2 V and 0.4 Ω, are meant to be in series, but one is connected the wrong way round. They drive a 4 Ω resistor. The current is
(a) 1.67 A (b) 2 A (c) 0.5 A (d) 1 A
25. Assertion (A): Manganin is used to make standard resistance coils. Reason (R): Manganin has a very small temperature coefficient of resistance.
(a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true
26. Two 220 V, 100 W bulbs are connected in series across 220 V. The total power used is
(a) 200 W (b) 100 W (c) 50 W (d) 25 W
27. A cell has E = 1.5 V and r = 0.5 Ω. Match List I with List II.
List I: A. Short-circuit current; B. Terminal voltage on open circuit; C. Terminal voltage with a 1 Ω load; D. Current with a 2.5 Ω load
List II: (i) 3 A; (ii) 1 V; (iii) 0.5 A; (iv) 1.5 V
(a) A-i, B-iv, C-ii, D-iii (b) A-iii, B-iv, C-ii, D-i (c) A-i, B-ii, C-iv, D-iii (d) A-iv, B-i, C-ii, D-iii
28. A fixed volume of metal is drawn into wires of different lengths L. The graph of resistance R against L is
(a) a straight line through the origin (b) a rectangular hyperbola (c) a straight line with negative slope (d) a parabola through the origin
29. A battery sends 1 A through a 2 Ω resistor and 0.5 A through a 5 Ω resistor. Its emf and internal resistance are
(a) 3 V, 2 Ω (b) 3 V, 1 Ω (c) 1.5 V, 1 Ω (d) 6 V, 1 Ω
30. Twelve identical resistors R form the edges of a cube. The resistance between the two ends of a face diagonal is
(a) 5R/6 (b) 3R/4 (c) 7R/12 (d) R/2
Mock Test 2 answer key
| Q | Ans | Reason |
|---|---|---|
| 1 | b | σ in S m⁻¹, μ in m² V⁻¹ s⁻¹, J in A m⁻², α in K⁻¹ |
| 2 | c | Length doubled at constant volume gives 4 × 6 = 24 Ω |
| 3 | b | Both true; the thin wire is faster because v_d = I/(neA), not because of ρ |
| 4 | d | I = 6/6 = 1 A, V = 5 V, I²r = 1 W; efficiency 5/6 = 83%, so D is wrong |
| 5 | d | Steeper I-V line means smaller R, which for a metal means lower temperature |
| 6 | c | E²/4r = 144/2 = 72 W |
| 7 | c | 1100/220 = 5 A |
| 8 | d | 1.1 kW × 3 h × 30 = 99 units, × Rs 7 = Rs 693 |
| 9 | c | 3.2/(1.6 × 10⁻¹⁹) = 2 × 10¹⁹ |
| 10 | b | 1/2 + 1/3 + 1/6 = 1, so 1 Ω |
| 11 | c | R = V²/P: 400, 800, 50, 62.5 Ω |
| 12 | d | R/12 = 60/40, so R = 18 Ω |
| 13 | b | 20(1 + 0.004 × 50) = 24 Ω |
| 14 | c | A is true; in opposition the stronger cell discharges and the weaker one is charged |
| 15 | a | Two paths of 18 Ω in parallel give 9 Ω |
| 16 | c | X: E = 6 V, r = 2 Ω; Y: E = 4 V, r = 1 Ω |
| 17 | a | All four are correct |
| 18 | d | 220²/110 = 440 W |
| 19 | c | 220²/27.5 = 1760 W |
| 20 | b | 27 × 10⁴ Ω = 270 kΩ, gold ±5% |
| 21 | c | Slope of J-E is σ = 1/ρ, so ρ_P : ρ_Q = 1 : 2 |
| 22 | b | V_Y = V_X − 4 + 10 − 2 = V_X + 4, so V_X − V_Y = −4 V |
| 23 | d | Galvanometer resistance does not affect the balance, so C is wrong |
| 24 | d | Net emf (5 − 2) × 2 = 6 V, r = 2 Ω; I = 6/(4 + 2) = 1 A |
| 25 | a | Its tiny α keeps its resistance steady, which is exactly why it is used |
| 26 | c | R = 484 Ω each; 220²/968 = 50 W |
| 27 | a | E/r = 3 A; open circuit 1.5 V; 1.5/1.5 = 1 A gives V = 1 V; 1.5/3 = 0.5 A |
| 28 | d | R = ρL/A with A = vol/L gives R = ρL²/vol |
| 29 | b | 1(2 + r) = 0.5(5 + r) gives r = 1 Ω, E = 3 V |
| 30 | b | Standard cube result: face diagonal 3R/4 |