Chapter 4 of 12 · 22 min read

Chapter 2: Ohm's Law, Resistance and Resistivity

Resistance tells you how hard a conductor fights the current. Resistivity tells you how hard the material itself fights, whatever its shape.

What you will learn

  • State Ohm's law and derive it from the drift picture.

  • Separate resistance (depends on shape) from resistivity (depends on material and temperature).

  • Read V-I graphs of ohmic and non-ohmic devices.

  • Handle stretched, drawn and cut wires quickly.

  • Read a carbon resistor colour code.

2.1 Ohm's law

At a fixed temperature, the current through a metal conductor is proportional to the potential difference across it:

V=IRV = IR

R is the resistance. Its SI unit is the ohm (Ω): 1 Ω = 1 V/A. The dimensional formula of R is [ML²T⁻³A⁻²].

Now derive it from Chapter 1. Take a wire of length L and area A with potential difference V. The field inside is E = V/L. We found J = σE with σ = ne²τ/m. So:

I=JA=σAVL⇒V=(LσA)II = JA = \sigma A\frac{V}{L} \quad\Rightarrow\quad V = \left(\frac{L}{\sigma A}\right) I

Comparing with V = IR:

R=ρLA,ρ=1σ=mne2τR = \frac{\rho L}{A}, \qquad \rho = \frac{1}{\sigma} = \frac{m}{ne^2\tau}

The reciprocal of resistance is conductance, G = 1/R. Its unit is the siemens (S), which is Ω⁻¹.

2.2 Resistance and resistivity are different

Resistance belongs to an object. Resistivity belongs to a material. A long thin copper wire and a short thick copper rod have very different resistances but the same resistivity.

QuantitySymbol and unitDepends onDoes not depend on
ResistanceR, ohmMaterial, temperature, length, areaCurrent or voltage (for ohmic conductors)
Resistivityρ, ohm metreMaterial, temperatureLength, area, shape
Conductivityσ, S m⁻¹Material, temperatureLength, area, shape

Why does a longer wire resist more? Electrons must cross more of the lattice. Why does a thicker wire resist less? More free electrons share the flow, like more lanes on a highway.

Typical resistivities at room temperature:

MaterialClassρ (Ω m), approximate
SilverConductor1.6 × 10⁻⁸
CopperConductor1.7 × 10⁻⁸
NichromeAlloy1.0 × 10⁻⁶
Silicon (pure)Semiconductorabout 2 × 10³
GlassInsulator10¹⁰ to 10¹⁴

This is why house wiring uses copper and a room heater coil uses nichrome.

2.3 V-I characteristics

If you plot I against V for a conductor, the shape tells you whether it obeys Ohm's law.

An ohmic conductor gives a straight line through the origin. On an I-V graph (I vertical), the slope is 1/R. A steeper line means a smaller resistance. On a V-I graph (V vertical), the slope is R itself, so read the axes first.

A non-ohmic device breaks Ohm's law in one of three ways:

  1. The graph is not a straight line. A filament bulb is the classic case. As current rises, the filament heats up and its resistance rises, so the curve bends towards the V axis.

  2. The graph depends on the sign of V. A p-n junction diode lets current through easily one way and hardly at all the other way.

  3. The same current can occur at more than one voltage. Gallium arsenide shows a region where current falls as V rises.

Figure 2.1 · I-V graphs of ohmic and non-ohmic devices
Figure 2.1 · I-V graphs of ohmic and non-ohmic devices

The metal wire gives a straight line of slope 1/R; the filament curve flattens as it heats, and the diode passes almost no current for negative V.

For a curved graph, two resistances can be defined at a point:

Rstatic=VI,Rdynamic=dVdIR_{static} = \frac{V}{I}, \qquad R_{dynamic} = \frac{dV}{dI}

For an ohmic conductor both are equal. For a non-ohmic device they differ.

2.4 Stretched, drawn and cut wires

When a wire is stretched or drawn through a die, its volume stays the same. So LA = constant.

If the length becomes n times, the area becomes 1/n times:

R′=ρnLA/n=n2RR' = \rho\frac{nL}{A/n} = n^2 R

If the radius becomes 1/k times, the area becomes 1/k² and the length becomes k² times:

R′=k4RR' = k^4 R

For a small stretch, take logs of R = ρL²/(volume):

ΔRR=2 ΔLL\frac{\Delta R}{R} = 2\,\frac{\Delta L}{L}

This works only for small changes, below about 5 per cent. For a 10 per cent stretch, use 1.1² = 1.21, a 21 per cent rise.

For wires of the same material, it often helps to write R in terms of mass M and density d:

R=ρL2dM=ρMdA2R = \frac{\rho L^2 d}{M} = \frac{\rho M}{d A^2}

Cutting is different from stretching. Cut a wire of resistance R into n equal pieces and each piece has R/n. The resistivity of each piece is unchanged.

2.5 Carbon resistor colour code

The colour code is not named in the NMC 2026 list, so treat this as a quick reference only. Four bands are read from the end nearest a band:

  • Bands 1 and 2: digits. Band 3: power of ten multiplier. Band 4: tolerance.

  • Digits 0 to 9: black, brown, red, orange, yellow, green, blue, violet, grey, white.

  • Tolerance: gold 5 per cent, silver 10 per cent, no band 20 per cent.

Worked example 2.1: An electric toaster draws 4 A from a 220 V supply. Find its resistance and conductance.

Solution: R = V/I = 220/4 = 55 Ω. G = 1/55 ≈ 0.018 S.

Worked example 2.2: A copper wire is 50 m long with a cross-section of 1 mm². Take ρ = 1.7 × 10⁻⁸ Ω m. Find its resistance.

Solution: R = ρL/A = 1.7 × 10⁻⁸ × 50 / 10⁻⁶ = 0.85 Ω.

Worked example 2.3: A 5 Ω wire is stretched to three times its length. Find the new resistance.

Solution: R' = n²R = 9 × 5 = 45 Ω.

Worked example 2.4: A wire is drawn until its radius is half the original. Its resistance was 2 Ω. Find the new resistance.

Solution: k = 2, so R' = k⁴R = 16 × 2 = 32 Ω.

Worked example 2.5: A wire is stretched so that its length increases by 0.5 per cent. By what percentage does its resistance change?

Solution: ΔR/R = 2 × 0.5 = 1 per cent increase.

Worked example 2.6: A carbon block measures 1 cm × 2 cm × 4 cm. Find the ratio of the largest to the smallest resistance between opposite faces.

Solution: Largest R: current along the 4 cm side, through the 1 × 2 face. R = ρ × 4/2 = 2ρ (in cm units). Smallest R: current along the 1 cm side, through the 2 × 4 face. R = ρ × 1/8. Ratio = 2 ÷ (1/8) = 16.

Worked example 2.7: A carbon resistor has bands yellow, violet, red, gold. Find its value.

Solution: Yellow = 4, violet = 7, red = multiplier 10². So R = 47 × 100 = 4.7 kΩ, with tolerance 5 per cent.

Worked example 2.8: Two wires of the same metal have masses in the ratio 1 : 2 and lengths in the ratio 2 : 1. Find the ratio of their resistances.

Solution: R ∝ L²/M. R₁/R₂ = (4/1) × (2/1) = 8. So R₁ : R₂ = 8 : 1.

Worked example 2.9: A device obeys I = 0.02V² (SI units). At V = 5 V, find its static and dynamic resistance.

Solution: I = 0.02 × 25 = 0.5 A, so R_static = 5/0.5 = 10 Ω. dI/dV = 0.04V = 0.2 S, so R_dynamic = 1/0.2 = 5 Ω. The device is non-ohmic.

Quick revision

  • V = IR at constant temperature for ohmic conductors.

  • R = ρL/A; ρ = m/(ne²τ) depends only on material and temperature.

  • Conductance G = 1/R in siemens; conductivity σ = 1/ρ in S m⁻¹.

  • Ohmic: straight I-V line through origin. Filament, diode, GaAs are non-ohmic.

  • Stretch to n times length: R becomes n²R. Radius to 1/k: R becomes k⁴R.

  • Small stretch: ΔR/R = 2ΔL/L.

  • Cut into n equal parts: each part R/n.

NEET traps

  • Saying resistivity changes when a wire is stretched. Only resistance changes.

  • Using ΔR/R = 2ΔL/L for a large stretch like 10 per cent. Use n².

  • Mixing up slopes: on an I-V graph slope is 1/R, on a V-I graph slope is R.

  • Forgetting that the area also changes when length changes at fixed volume.

  • Converting mm² to m² wrongly. 1 mm² = 10⁻⁶ m², not 10⁻³.

  • Using diameter in place of radius in A = πr².

Practice MCQs: Chapter 2

Level 1: Concept check

1. The SI unit of resistivity is (a) Ω m⁻¹ (b) Ω m⁻² (c) Ω m (d) Ω⁻¹ m

2. The resistivity of a wire depends on (a) its material and temperature (b) its length only (c) its area only (d) its length and area

3. The SI unit of conductance is (a) ohm (b) ohm metre (c) volt per ampere (d) siemens

4. For an ohmic conductor at constant temperature, the I-V graph is (a) a parabola (b) a straight line through the origin (c) a hyperbola (d) a straight line parallel to the V axis

5. Which of these is non-ohmic? (a) A p-n junction diode (b) A copper wire at constant temperature (c) A nichrome wire at constant temperature (d) A manganin wire at constant temperature

6. The resistance of a uniform wire of length L and area A is (a) ρA/L (b) ρ/(LA) (c) ρL/A (d) LA/ρ

7. In terms of electron density n and relaxation time τ, resistivity is (a) ne²τ/m (b) m/(ne²τ) (c) neτ/m (d) m/(neτ)

8. The dimensional formula of resistance is (a) [ML²T⁻²A⁻²] (b) [ML²T⁻³A⁻¹] (c) [MLT⁻³A⁻²] (d) [ML²T⁻³A⁻²]

9. A wire is cut into two equal halves. The resistivity of each half is (a) halved (b) doubled (c) unchanged (d) four times

10. A 12 V battery drives 0.5 A through a resistor. Its resistance is (a) 24 Ω (b) 6 Ω (c) 12 Ω (d) 0.04 Ω

Level 2: NEET standard

11. A copper wire 100 m long has a cross-section of 2 mm². With ρ = 1.7 × 10⁻⁸ Ω m, its resistance is (a) 0.17 Ω (b) 0.85 Ω (c) 1.7 Ω (d) 8.5 Ω

12. An 8 Ω wire is stretched to twice its length. Its new resistance is (a) 16 Ω (b) 4 Ω (c) 8 Ω (d) 32 Ω

13. A 2 Ω wire is drawn so that its radius becomes half. The new resistance is (a) 32 Ω (b) 8 Ω (c) 16 Ω (d) 4 Ω

14. A wire is stretched so its length increases by 2 per cent. Its resistance increases by (a) 2 per cent (b) 1 per cent (c) about 4 per cent (d) 8 per cent

15. Two wires of the same metal have lengths in the ratio 1 : 2 and diameters in the ratio 2 : 1. Their resistances are in the ratio (a) 1 : 2 (b) 2 : 1 (c) 8 : 1 (d) 1 : 8

16. A carbon resistor has bands brown, black, orange, silver. Its value is (a) 1 kΩ ± 10 per cent (b) 10 kΩ ± 10 per cent (c) 10 kΩ ± 5 per cent (d) 100 kΩ ± 10 per cent

17. On an I-V graph (I vertical, V horizontal), the line for wire P is steeper than the line for wire Q. Then (a) R_P is less than R_Q (b) R_P is greater than R_Q (c) R_P equals R_Q (d) they cannot be compared

18. The I-V graph of a filament bulb bends because (a) its resistivity falls on heating (b) Ohm's law fails for all metals (c) its resistance rises as the filament heats up (d) the supply is AC

19. A 20 Ω wire is cut into four equal pieces. The resistance of each piece is (a) 80 Ω (b) 5 Ω (c) 20 Ω (d) 1.25 Ω

20. A metal block measures 1 cm × 2 cm × 3 cm. The ratio of its largest to smallest resistance between opposite faces is (a) 3 (b) 6 (c) 4.5 (d) 9

21. Two wires of the same metal have equal mass. Their lengths are in the ratio 1 : 3. Their resistances are in the ratio (a) 1 : 9 (b) 1 : 3 (c) 3 : 1 (d) 9 : 1

22. A metal has n = 8 × 10²⁸ m⁻³ and τ = 2.5 × 10⁻¹⁴ s. Taking m = 9.1 × 10⁻³¹ kg, its conductivity is about (a) 5.6 × 10⁵ S/m (b) 1.8 × 10⁻⁸ S/m (c) 5.6 × 10⁷ S/m (d) 2.8 × 10⁷ S/m

Level 3: Challenge

23. A wire is stretched so its length increases by 10 per cent. Its resistance increases by (a) 10 per cent (b) 20 per cent (c) 11 per cent (d) 21 per cent

24. A metal pipe of length L has inner radius r₁ and outer radius r₂. Its resistance along its length is (a) ρL/(πr₂²) (b) ρL/[π(r₂² − r₁²)] (c) ρL/[π(r₂ − r₁)²] (d) ρL/(2πr₁)

25. Wire A has length L and diameter d. Wire B, of the same metal, has length 2L and diameter 2d. The same potential difference is applied across each. The ratio of currents I_A : I_B is (a) 2 : 1 (b) 1 : 1 (c) 1 : 2 (d) 1 : 4

26. A 4 Ω wire is drawn until its radius is one-third of the original. Its new resistance is (a) 324 Ω (b) 36 Ω (c) 108 Ω (d) 12 Ω

27. A device obeys I = 0.05V² (SI units). Its dynamic resistance at V = 4 V is (a) 5 Ω (b) 20 Ω (c) 0.4 Ω (d) 2.5 Ω

28. In a metal, the free electron density doubles while the relaxation time halves. The resistivity (a) doubles (b) does not change (c) halves (d) becomes four times

29. Assertion (A): The resistance of a metal wire increases when it is stretched. Reason (R): The resistivity of a metal increases when the wire is stretched. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: The static resistance V/I of a filament lamp is the same at every voltage. Statement II: A p-n junction diode conducts far more easily in one direction than in the other. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1cρ = RA/L, so Ω m
2aResistivity is a material property
3dG = 1/R, unit siemens
4bI is proportional to V
5aDiode current depends on direction
6cR = ρL/A
7bρ = 1/σ = m/(ne²τ)
8dR = V/I = [ML²T⁻³A⁻¹]/[A]
9cMaterial and temperature unchanged
10a12/0.5 = 24 Ω
11b1.7 × 10⁻⁸ × 100/(2 × 10⁻⁶) = 0.85 Ω
12dn = 2, R' = 4 × 8
13ak = 2, R' = 16 × 2
14cΔR/R = 2 × 2 per cent (exactly 4.04)
15dR ∝ L/d² = (1/4) : (2/1)
16b1, 0, ×10³, silver 10 per cent
17aSlope of I-V is 1/R
18cHotter filament has higher resistance
19b20/4 = 5 Ω
20d(3/2) ÷ (1/6) = 9
21aEqual mass: R ∝ L²
22cσ = ne²τ/m ≈ 5.6 × 10⁷ S/m
23d1.1² = 1.21
24bArea of the ring = π(r₂² − r₁²)
25cR_B = ρ(2L)/(4A) = R_A/2, so I_B = 2I_A
26ak = 3, 81 × 4 = 324 Ω
27ddI/dV = 0.1V = 0.4 S, R = 2.5 Ω
28bρ = m/(ne²τ), nτ unchanged
29cResistivity is unchanged; L rises and A falls
30dLamp R rises with V; diode is one-way

Chapter 2 revision sheet

One-page summary

  • Ohm's law: at fixed temperature and physical state, V = IR for an ohmic conductor.

  • Resistance of a wire: R = ρL/A. Resistivity ρ depends only on the material and temperature, not on size or shape.

  • From the drift model, ρ = m/(ne²τ) and conductivity σ = 1/ρ.

  • Conductance G = 1/R, unit siemens (S). Conductivity unit S m⁻¹.

  • Ohmic devices give a straight V-I line through the origin. Diodes, bulbs at high current and thermistors are non-ohmic.

  • Static resistance = V/I; dynamic resistance = dV/dI (slope). They are equal only for ohmic devices.

  • Stretching at constant volume: length n times gives R' = n²R; radius 1/k times gives R' = k⁴R.

  • A small stretch of x% raises R by about 2x%.

  • Cutting a wire into n equal parts gives R/n each; joining them in parallel gives R/n².

  • For wires of the same material, R = ρL²/(volume), so R ∝ L²/M for given density.

  • Colour code digits 0–9: black, brown, red, orange, yellow, green, blue, violet, grey, white.

  • Band 1 and 2 give digits, band 3 the power of ten, band 4 the tolerance: gold ±5%, silver ±10%, none ±20%.

  • Good conductors: ρ ~ 10⁻⁸ Ω m; alloys like nichrome ~ 10⁻⁶ Ω m; insulators like glass 10¹⁰ to 10¹⁴ Ω m.

R=ρLA,ρ=mne2τ,R′=n2R (stretch),ΔRR=2ΔLLR = \frac{\rho L}{A}, \quad \rho = \frac{m}{ne^2\tau}, \quad R' = n^2 R \ (\text{stretch}), \quad \frac{\Delta R}{R} = 2\frac{\Delta L}{L}

Must-remember table

QuantityFormulaSI unitDimensions
ResistanceR = V/IΩ[M L² T⁻³ A⁻²]
Resistivityρ = RA/LΩ m[M L³ T⁻³ A⁻²]
ConductanceG = 1/RS[M⁻¹ L⁻² T³ A²]
Conductivityσ = 1/ρS m⁻¹[M⁻¹ L⁻³ T³ A²]
Stretch, length × nR' = n²RΩ—
Draw, radius ÷ kR' = k⁴RΩ—

Memory aids

  • "B B ROY Goes to Bombay Via Grey Wagon": Black 0, Brown 1, Red 2, Orange 3, Yellow 4, Green 5, Blue 6, Violet 7, Grey 8, White 9.

  • "Gold 5, Silver 10, Nothing 20": tolerance bands ±5%, ±10%, ±20%.

  • "Stretch squares, squeeze fours": length n times gives n²; radius 1/k gives k⁴.

  • "Rho is the material's ID card": ρ belongs to the material (and temperature), never to the wire's length or area.

Concept connections

  • Resistivity in terms of n and τ comes from the drift model in Chapter 1 of this book.

  • Dimensional formulas of R and ρ are tested along with Physics Book 1: Physics and Measurement.

  • Non-ohmic V-I curves of diodes are studied in Physics Book 19: Electronic Devices.

Practice MCQs: Chapter 2, Level 4 (new NEET pattern)

31. Match the colour bands in List I with the resistance in List II.

  • List I: A. Brown, black, red, gold; B. Red, red, orange, silver; C. Yellow, violet, brown, gold; D. Green, blue, black, no fourth band

  • List II: (i) 470 Ω ± 5%; (ii) 56 Ω ± 20%; (iii) 1 kΩ ± 5%; (iv) 22 kΩ ± 10%

(a) A-i, B-iv, C-iii, D-ii (b) A-iii, B-ii, C-i, D-iv (c) A-iii, B-iv, C-i, D-ii (d) A-iv, B-iii, C-ii, D-i

32. A uniform wire has resistance 8 Ω. Match the change in List I with the new resistance in List II.

  • List I: A. Stretched to 3 times its length; B. Cut into 4 equal parts which are joined in parallel; C. Drawn so its radius halves; D. Folded in half so the two halves are in parallel

  • List II: (i) 2 Ω; (ii) 128 Ω; (iii) 0.5 Ω; (iv) 72 Ω

(a) A-iv, B-ii, C-iii, D-i (b) A-iv, B-iii, C-ii, D-i (c) A-ii, B-iii, C-iv, D-i (d) A-i, B-iii, C-ii, D-iv

33. Match the material in List I with the order of its resistivity at room temperature in List II.

  • List I: A. Copper; B. Nichrome; C. Pure silicon; D. Glass

  • List II: (i) 10⁻⁶ Ω m; (ii) 10¹² Ω m; (iii) 10⁻⁸ Ω m; (iv) 10³ Ω m

(a) A-i, B-iii, C-iv, D-ii (b) A-iii, B-iv, C-i, D-ii (c) A-iii, B-i, C-ii, D-iv (d) A-iii, B-i, C-iv, D-ii

34. Match the quantity in List I with its dimensions in List II.

  • List I: A. Resistance; B. Resistivity; C. Conductance; D. Conductivity

  • List II: (i) [M L³ T⁻³ A⁻²]; (ii) [M⁻¹ L⁻³ T³ A²]; (iii) [M L² T⁻³ A⁻²]; (iv) [M⁻¹ L⁻² T³ A²]

(a) A-iii, B-i, C-iv, D-ii (b) A-i, B-iii, C-ii, D-iv (c) A-iii, B-i, C-ii, D-iv (d) A-iv, B-ii, C-iii, D-i

35. How many of the following statements are correct?

  • A. Resistivity of a wire depends on its length and area.

  • B. Resistance of a wire depends on its material, length, area and temperature.

  • C. For an ohmic conductor at constant temperature, the V-I graph is a straight line through the origin.

  • D. A junction diode is a non-ohmic device.

  • E. Static resistance V/I and dynamic resistance dV/dI are equal for every device.

(a) 5 (b) 2 (c) 4 (d) 3

36. A wire is stretched uniformly so that its length increases by 0.5% while its volume stays the same. Choose the correct set of statements.

  • A. Its resistance increases by about 1%.

  • B. Its resistivity increases by about 1%.

  • C. Its cross-sectional area decreases by about 0.5%.

  • D. Its resistance increases by about 0.25%.

(a) A and B only (b) B and D only (c) A and C only (d) A, B and C only

37. Choose the correct set of statements about resistivity ρ = m/(ne²τ).

  • A. ρ of a metal rises with temperature mainly because τ falls.

  • B. ρ of a semiconductor falls with temperature mainly because n rises.

  • C. A thick and a thin wire of the same metal at the same temperature have the same ρ.

  • D. Doubling the length of a wire doubles its resistivity.

(a) A and D only (b) B and C only (c) A, B and D only (d) A, B and C only

38. How many of the following statements about the carbon resistor colour code are correct?

  • A. A gold fourth band means a tolerance of ±5%.

  • B. The third band gives the multiplier (power of ten).

  • C. A silver fourth band means a tolerance of ±20%.

  • D. Grey stands for the digit 8.

(a) 2 (b) 3 (c) 4 (d) 1

39. V-I graphs (V on the y-axis, I on the x-axis) of two wires P and Q of the same material and length are straight lines through the origin. Line P makes 60° and line Q makes 30° with the I-axis. The ratio of their cross-sectional areas A_P : A_Q is

(a) 1 : 3 (b) 3 : 1 (c) 1 : √3 (d) √3 : 1

40. A device gives these readings. Its dynamic resistance between 0.7 V and 0.8 V is

V (V)I (mA)
0.50
0.65
0.725
0.865

(a) 12.3 Ω (b) 4 Ω (c) 28 Ω (d) 2.5 Ω

41. Graphs of resistance R (y-axis) against length L (x-axis) are drawn for three wires of the same material with diameters 1 mm, 2 mm and 3 mm. All three are straight lines through the origin. Which wire has the steepest line, and what is the ratio of the slope for 1 mm to that for 3 mm?

(a) 3 mm wire, 9 : 1 (b) 1 mm wire, 9 : 1 (c) 1 mm wire, 3 : 1 (d) 3 mm wire, 1 : 9

Passage for Q42–Q43: A student repairing a room heater has 2.0 m of nichrome wire of diameter 0.50 mm. Nichrome has resistivity 1.0 × 10⁻⁶ Ω m.

42. The resistance of the wire is about

(a) 10.2 Ω (b) 2.5 Ω (c) 40.7 Ω (d) 5.1 Ω

43. The same wire is drawn out uniformly to 4.0 m. Its new resistance is about

(a) 20.4 Ω (b) 40.7 Ω (c) 81.5 Ω (d) 10.2 Ω

44. Two wires A and B of the same material have masses in the ratio 1 : 2 and lengths in the ratio 2 : 1. The ratio R_A : R_B is

(a) 2 : 1 (b) 4 : 1 (c) 1 : 8 (d) 8 : 1

45. A uniform wire of resistance 4 Ω is drawn until its radius is half the original. It is then cut into 4 equal pieces, which are joined in parallel. The final resistance is

(a) 1 Ω (b) 16 Ω (c) 4 Ω (d) 64 Ω

Level 4 answer key

QAnsReason
31c10 × 10² = 1 kΩ; 22 × 10³ = 22 kΩ; 47 × 10 = 470 Ω; 56 × 1 = 56 Ω with ±20%
32b3² × 8 = 72; 8/4² = 0.5; 2⁴ × 8 = 128; 8/2² = 2
33dCu ~10⁻⁸, nichrome ~10⁻⁶, pure Si ~10³, glass ~10¹² Ω m
34aρ = RA/L adds one L; G and σ are the reciprocals
35dB, C, D are correct; ρ is a material property, and static and dynamic resistance differ for non-ohmic devices
36cΔR/R = 2ΔL/L = 1%; A falls by the same 0.5% as L rises; ρ does not change
37dD is wrong: length changes R, not ρ
38bA, B, D are correct; silver means ±10%
39aR_P/R_Q = tan 60°/tan 30° = 3, and R ∝ 1/A, so A_P : A_Q = 1 : 3
40ddV/dI = 0.1 V/0.040 A = 2.5 Ω
41bSlope = ρ/A ∝ 1/d², so the thinnest wire is steepest; (3/1)² = 9 : 1
42aA = π(0.25 × 10⁻³)² = 1.96 × 10⁻⁷ m²; R = 10⁻⁶ × 2/1.96 × 10⁻⁷ = 10.2 Ω
43bLength doubles at constant volume, so R becomes 4 × 10.2 = 40.7 Ω
44dR ∝ L²/M: (2²)/(1/2) = 8, so 8 : 1
45cRadius halved gives 16 × 4 = 64 Ω; four pieces of 16 Ω in parallel give 4 Ω
22 min left
‹
›