Chapter 1: Electric Current, Drift Velocity and Mobility
Current is charge on the move. In a metal wire, the charges that move are free electrons, and they move far more slowly than most students expect.
What you will learn
Define electric current, average and instantaneous, and find charge from an I-t graph.
Define current density and see why it is a vector while current is not.
Picture free electrons in a metal and understand relaxation time.
Derive drift velocity and the relation I = neAv_d.
Define mobility and connect it to drift velocity and conductivity.
1.1 Electric current
When charge crosses a section of a wire, we say current flows. Current is the rate at which charge crosses that section.
If charge Δq crosses in time Δt, the average current is:
If the flow changes with time, we take the limit and get the instantaneous current:
The SI unit is the ampere (A). One ampere means one coulomb crossing every second. Since charge comes in packets of e, a charge q is always q = ne, where n is a whole number.
Two useful results follow from I = dq/dt:
The charge that flows between two times is the area under the I-t graph.
The slope of a q-t graph at any instant gives the current at that instant.
Current has a direction, but it is a scalar. When two currents meet at a junction, they simply add as numbers. They do not follow the triangle law. By convention, current points the way positive charge would move. In a metal, electrons move opposite to this.
Current also flows without wires. A charge q going round a circle f times per second crosses any point f times each second, so it is a current:
1.2 Current density
Current tells you the total flow. Current density tells you how crowded that flow is. For a current I spread evenly and normal to an area A:
Its unit is A m⁻². Current density is a vector, pointing along the flow at that point. In general:
Think of a pressure cooker vent. The same steam rushes faster through a narrow nozzle. In a wire whose cross-section changes, the current is the same at every section, but J is larger where the wire is thinner.
1.3 Free electrons in a metal
In a metal like copper, each atom gives up one or more outer electrons. These free electrons wander through a fixed lattice of positive ions. At room temperature they move randomly at about 10⁵ m/s.
They keep colliding with the vibrating ions. Each collision sends them off in a random new direction. With no field, the velocities point every which way, so their average is zero:
So random motion alone gives no current, however fast it is. The average time between two successive collisions is called the relaxation time, τ. For metals at room temperature, τ is of the order of 10⁻¹⁴ s.
1.4 Drift velocity
Now apply a potential difference, so there is a field E inside the wire. Each electron feels a force −eE and gains an acceleration:
Just after a collision, electron i has velocity uᵢ. After time tᵢ it has:
Average this over all the electrons. The average of uᵢ is zero, and the average of tᵢ is τ. So the average velocity, called the drift velocity, is:
The minus sign shows the drift is opposite to E. Its size is tiny, of the order of 10⁻⁴ m/s in household wires. That is slower than an ant.

One electron's fast zig-zag path between ions ends up shifted slightly to the left, opposite to E, while conventional current points along E.
| Feature | Random thermal motion | Drift motion |
|---|---|---|
| Cause | Temperature | Applied electric field |
| Typical speed | About 10⁵ m/s | About 10⁻⁴ m/s |
| Direction | Random | Opposite to E |
| Average velocity | Zero | v_d, not zero |
| Net current | None | Yes |
If drift is so slow, why does a ceiling fan start the moment you press the switch? The wire is already full of free electrons. The field is set up through the whole circuit almost at the speed of light, so electrons everywhere start drifting together.
1.5 Relation between current and drift velocity
Take a wire of cross-section A with n free electrons per unit volume, each drifting at speed v_d. In time Δt each electron moves a distance v_dΔt.
So all electrons inside a length v_dΔt cross a given section in that time. That length holds a volume Av_dΔt and nAv_dΔt electrons. The charge crossing is:
Divide by Δt:
For copper, n is about 8.5 × 10²⁸ m⁻³. Because n is huge, a small v_d still gives a large current.
Two quick results NEET loves:
In one wire with uneven cross-section, I and n are fixed, so v_d ∝ 1/A.
For a fixed potential difference V across length L, E = V/L, so v_d ∝ V/L.
1.6 Mobility
Mobility tells you how easily a charge carrier drifts in a field. It is the drift speed per unit field:
The SI unit is m² V⁻¹ s⁻¹. Mobility is positive by definition. It depends on the material and its temperature, not on the field applied.
Now combine J = nev_d with v_d = μE:
So J is proportional to E. The constant ne²τ/m is the conductivity σ of the material. This is Ohm's law in its basic form, which we build on in Chapter 2.
In semiconductors, both electrons and holes carry current. Electrons usually have a higher mobility than holes.
Worked example 1.1: A charge of 3.2 C passes through a torch bulb filament in 4 s. Find the current and the number of electrons passing per second.
Solution: I = q/t = 3.2/4 = 0.8 A. Electrons per second = I/e = 0.8/(1.6 × 10⁻¹⁹) = 5 × 10¹⁸.
Worked example 1.2: The current in a wire varies as I = (4 + 2t) A. How much charge flows from t = 0 to t = 3 s?
Solution: q = ∫(4 + 2t)dt from 0 to 3 = [4t + t²] = 12 + 9 = 21 C. Note that you cannot simply multiply the current at 3 s by 3 s, because the current is not constant.
Worked example 1.3: A copper wire of cross-section 1.0 mm² carries 1.7 A. Take n = 8.5 × 10²⁸ m⁻³. Find the drift speed.
Solution: v_d = I/(neA) = 1.7 / (8.5 × 10²⁸ × 1.6 × 10⁻¹⁹ × 1.0 × 10⁻⁶) = 1.7/13600 = 1.25 × 10⁻⁴ m/s.
Worked example 1.4: In Worked example 1.3, how long does an electron take to drift 1 m along the wire?
Solution: t = 1/(1.25 × 10⁻⁴) = 8000 s, which is about 2 h 13 min. The lamp still glows at once because the field, not the electron, travels fast.
Worked example 1.5: In a conductor, a field of 0.5 V/m produces a drift speed of 2 × 10⁻⁴ m/s. Find the mobility and the relaxation time. Take m = 9.1 × 10⁻³¹ kg.
Solution: μ = v_d/E = 2 × 10⁻⁴/0.5 = 4 × 10⁻⁴ m² V⁻¹ s⁻¹. Then τ = μm/e = 4 × 10⁻⁴ × 9.1 × 10⁻³¹ / 1.6 × 10⁻¹⁹ ≈ 2.3 × 10⁻¹⁵ s.
Worked example 1.6: A wire has two sections whose diameters are in the ratio 1 : 2. The same current flows through both. Find the ratio of drift speeds.
Solution: v_d ∝ 1/A ∝ 1/d². Area ratio is 1 : 4, so v₁ : v₂ = 4 : 1. The thin part has the faster drift.
Worked example 1.7: A plastic ring carrying 5 μC spins at 20 revolutions per second about its axis. What current does it make?
Solution: I = qf = 5 × 10⁻⁶ × 20 = 1 × 10⁻⁴ A = 100 μA.
Worked example 1.8: A wire is connected across a fixed potential difference V. It is then stretched to twice its length, volume unchanged, and connected across the same V. What happens to the drift speed and the current?
Solution: v_d = μE = μV/L. L doubles, so v_d halves. The area halves too, since volume is fixed. So I = neAv_d becomes (1/2)(1/2) = 1/4 of the original. You will get the same answer in Chapter 2, since the resistance becomes 4 times.
Quick revision
I = dq/dt. Charge = area under I-t graph. Current is a scalar.
J = I/A is a vector, unit A m⁻².
Random thermal motion gives zero average velocity and no current.
v_d = eEτ/m, opposite to E, about 10⁻⁴ m/s.
I = neAv_d and J = nev_d.
μ = v_d/E = eτ/m, unit m² V⁻¹ s⁻¹.
σ = ne²τ/m = neμ.
A charge q going round f times per second is a current qf.
NEET traps
Treating current as a vector because it has a direction. It does not follow vector addition.
Using I × t for charge when I changes with time. Integrate, or use area under the graph.
Thinking a thicker part of a wire carries more current. Current is the same; only J and v_d change.
Forgetting that stretching a wire changes both L and A.
Confusing thermal speed (10⁵ m/s) with drift speed (10⁻⁴ m/s).
Writing v_d ∝ V without checking whether L also changed.
Practice MCQs: Chapter 1
Level 1: Concept check
1. The SI unit of current density is (a) A m (b) A m⁻² (c) A m² (d) C m⁻²
2. A current of 0.4 A flows for 1 minute. The charge that passes is (a) 0.4 C (b) 2.4 C (c) 24 C (d) 240 C
3. The number of electrons crossing a section per second in a current of 1 A is (a) 6.25 × 10¹⁸ (b) 1.6 × 10¹⁹ (c) 6.25 × 10¹⁷ (d) 1.6 × 10⁻¹⁹
4. The drift speed of electrons in a household copper wire is of the order of (a) 3 × 10⁸ m/s (b) 10⁵ m/s (c) 1 m/s (d) 10⁻⁴ m/s
5. Mobility of a charge carrier is defined as (a) drift velocity per unit current (b) current per unit field (c) drift velocity per unit electric field (d) charge per unit drift velocity
6. Electric current is a scalar because (a) it does not obey the laws of vector addition (b) it has no direction (c) it is always constant (d) charge is a vector
7. In a metal with no applied field, the average velocity of free electrons is (a) equal to their thermal speed (b) zero (c) equal to drift speed (d) equal to the speed of light
8. The SI unit of mobility is (a) m s⁻¹ V⁻¹ (b) m V s⁻¹ (c) V m⁻² s (d) m² V⁻¹ s⁻¹
9. The current I in a wire in terms of drift speed v_d is (a) neAv_d (b) neA/v_d (c) nev_d/A (d) nAv_d/e
10. In a metal wire, free electrons drift (a) along the electric field (b) perpendicular to the field (c) opposite to the electric field (d) in random directions with no preference
Level 2: NEET standard
11. A wire of cross-section 2 mm² has 5 × 10²⁸ free electrons per m³ and carries 3.2 A. The drift speed is (a) 2 × 10⁻³ m/s (b) 4 × 10⁻⁴ m/s (c) 1 × 10⁻⁴ m/s (d) 2 × 10⁻⁴ m/s
12. The current in a conductor is I = 2t² + t (SI units). The charge that flows from t = 0 to t = 3 s is (a) 18 C (b) 22.5 C (c) 21 C (d) 63 C
13. A steady current flows through a metal wire whose cross-section decreases along its length. The quantity that stays the same at every section is (a) current (b) current density (c) drift speed (d) electric field
14. Two wires of the same metal carry equal currents. Their diameters are in the ratio 1 : 3. The ratio of their drift speeds is (a) 1 : 3 (b) 3 : 1 (c) 9 : 1 (d) 1 : 9
15. An electron moves in a circle of radius r with speed v. The equivalent current is (a) ev/r (b) ev/(2πr) (c) 2πre/v (d) evr/(2π)
16. If the relaxation time of electrons in a metal doubles, other things unchanged, the mobility (a) halves (b) stays the same (c) becomes four times (d) doubles
17. The potential difference across a given wire is doubled. The drift speed of electrons (a) doubles (b) halves (c) does not change (d) becomes four times
18. A wire of a given cross-section is replaced by a longer wire of the same material and cross-section, twice as long, across the same potential difference. The drift speed (a) doubles (b) does not change (c) halves (d) becomes one-fourth
19. The charge through a wire varies as q = 3t² + 2t (SI units). The current at t = 2 s is (a) 16 A (b) 12 A (c) 8 A (d) 14 A
20. Electrons in a sample have mobility 5 × 10⁻³ m² V⁻¹ s⁻¹. In a field of 200 V/m, their drift speed is (a) 0.1 m/s (b) 1 m/s (c) 10 m/s (d) 4 × 10⁴ m/s
21. A wire carries a current density of 2 × 10⁶ A m⁻². It has 8 × 10²⁸ free electrons per m³. The drift speed is about (a) 1.56 × 10⁻⁵ m/s (b) 6.4 × 10⁻⁴ m/s (c) 1.56 × 10⁻⁴ m/s (d) 3.1 × 10⁻⁴ m/s
22. Which statement about free electrons in a current-carrying wire is correct? (a) Drift speed is much smaller than the random thermal speed (b) Drift speed equals thermal speed (c) Drift speed is close to the speed of light (d) Thermal motion alone produces a net current
Level 3: Challenge
23. A thin ring of radius r carries charge q spread on it and spins about its axis with angular speed ω. The current is (a) qω (b) 2πqω (c) qω/π (d) qω/(2π)
24. A copper wire of cross-section 1 mm² carries 4 A. Take n = 8.5 × 10²⁸ m⁻³. The time an electron takes to drift 1.5 m is about (a) 8.5 min (b) 85 min (c) 42.5 min (d) 170 min
25. A wire across a fixed potential difference is stretched to three times its length (volume constant) and reconnected across the same potential difference. The drift speed becomes (a) one-third (b) one-ninth (c) three times (d) unchanged
26. For a metal, σ = 5.8 × 10⁷ S/m and n = 8.5 × 10²⁸ m⁻³. Taking m = 9.1 × 10⁻³¹ kg, the relaxation time is about (a) 2.4 × 10⁻¹⁰ s (b) 4.2 × 10⁻¹⁴ s (c) 2.4 × 10⁻¹⁴ s (d) 2.4 × 10⁻¹⁸ s
27. The current in a wire rises steadily from 0 to 6 A in 4 s and then stays at 6 A for 2 s more. The average current over the 6 s is (a) 3 A (b) 6 A (c) 5 A (d) 4 A
28. Two wires A and B of the same metal are joined end to end and carry a steady current. The radius of A is twice that of B. The ratio of the electric fields inside them, E_A : E_B, is (a) 4 : 1 (b) 1 : 4 (c) 1 : 2 (d) 2 : 1
29. Assertion (A): Drift speed of electrons is only about 10⁻⁴ m/s, yet a room bulb glows almost the moment the switch is pressed. Reason (R): The electric field is set up through the whole circuit almost at the speed of light, so free electrons everywhere start drifting together. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true
30. Statement I: For an ohmic conductor, the mobility of electrons does not depend on the applied electric field. Statement II: Current density is a scalar quantity. (a) Both true (b) Both false (c) I true, II false (d) I false, II true
Answer key with reasons
| Q | Ans | Reason |
|---|---|---|
| 1 | b | J = I/A |
| 2 | c | q = 0.4 × 60 = 24 C |
| 3 | a | 1/(1.6 × 10⁻¹⁹) = 6.25 × 10¹⁸ |
| 4 | d | Drift is very slow, about 10⁻⁴ m/s |
| 5 | c | μ = v_d/E |
| 6 | a | Currents add as numbers at a junction |
| 7 | b | Random velocities average to zero |
| 8 | d | (m/s)/(V/m) = m² V⁻¹ s⁻¹ |
| 9 | a | Derived in 1.5 |
| 10 | c | Force on electron is −eE |
| 11 | d | 3.2/(5 × 10²⁸ × 1.6 × 10⁻¹⁹ × 2 × 10⁻⁶) = 2 × 10⁻⁴ |
| 12 | b | [2t³/3 + t²/2] from 0 to 3 = 18 + 4.5 |
| 13 | a | Charge is not piling up, so I is the same |
| 14 | c | v_d ∝ 1/d² = 9 : 1 |
| 15 | b | I = e/T, T = 2πr/v |
| 16 | d | μ = eτ/m |
| 17 | a | E = V/L doubles, v_d = μE |
| 18 | c | E = V/L halves |
| 19 | d | I = 6t + 2 = 14 A |
| 20 | b | v_d = 5 × 10⁻³ × 200 = 1 m/s |
| 21 | c | v_d = J/(ne) = 2 × 10⁶/1.28 × 10¹⁰ |
| 22 | a | 10⁻⁴ m/s versus 10⁵ m/s |
| 23 | d | f = ω/2π, I = qf |
| 24 | b | v_d = 2.94 × 10⁻⁴ m/s, t = 5100 s = 85 min |
| 25 | a | E = V/L falls to one-third |
| 26 | c | τ = σm/(ne²) ≈ 2.4 × 10⁻¹⁴ s |
| 27 | d | Area = 12 + 12 = 24 C, 24/6 = 4 A |
| 28 | b | E = J/σ, J ∝ 1/r², so 1 : 4 |
| 29 | a | R is the reason the bulb lights at once |
| 30 | c | μ = eτ/m is field-free; J is a vector |
Chapter 1 revision sheet
One-page summary
Current is the rate of flow of charge: I = q/t (steady) or I = dq/dt (changing).
1 A = 1 C/s. A current of 1.6 A means 10¹⁹ electrons cross a section every second.
A charge q going round f times per second makes a current I = qf.
Conventional current flows from + to −; electrons drift the opposite way.
Current is a scalar (it adds like numbers). Current density J = I/A is a vector, unit A m⁻².
With no field, free electrons move randomly at high speed but their average velocity is zero.
In a field E, each electron gets acceleration eE/m between collisions.
Relaxation time τ is the average time between collisions, about 10⁻¹⁴ s in metals.
Drift speed v_d = eEτ/m, about 10⁻⁴ m/s in household wires.
Link between current and drift speed: I = neAv_d. In a wire of varying thickness, I is the same everywhere but v_d ∝ 1/A.
Mobility μ = v_d/E = eτ/m, unit m² V⁻¹ s⁻¹.
Ohm's law at the micro level: J = σE with σ = ne²τ/m = neμ.
A bulb lights at once because the field sets up along the wire almost at the speed of light, not because electrons rush to it.
Raising the temperature of a metal lowers τ, so mobility and conductivity fall.
Must-remember table
| Quantity | Formula | SI unit | Typical value (copper) |
|---|---|---|---|
| Current | I = dq/dt | A | 1–10 A at home |
| Current density | J = I/A | A m⁻² | about 10⁶ A m⁻² |
| Free-electron density | n | m⁻³ | 8.5 × 10²⁸ m⁻³ |
| Relaxation time | τ | s | about 10⁻¹⁴ s |
| Drift speed | v_d = I/(neA) | m s⁻¹ | about 10⁻⁴ m s⁻¹ |
| Mobility | μ = v_d/E = eτ/m | m² V⁻¹ s⁻¹ | about 4 × 10⁻³ |
| Conductivity | σ = ne²τ/m | S m⁻¹ | about 6 × 10⁷ S m⁻¹ |
Memory aids
"NEAV" (say "navy"): I = N·E·A·V_d, number density, electron charge, area, drift velocity.
"Slow walkers, fast news": electrons walk slowly (10⁻⁴ m/s) but the news of the field travels at nearly light speed.
"Thin pipe, fast flow": in a narrower part of the same wire, the same current needs a higher drift speed, like water in a narrow pipe.
"Hot metal, short tau": heating a metal shortens τ, so μ and σ both drop.
Concept connections
The field E inside the wire and the charge e come from Physics Book 11: Electrostatics.
Moving charges in wires create magnetic fields and feel forces, the subject of Physics Book 13: Magnetic Effects of Current and Magnetism.
Mobility of electrons and holes in semiconductors returns in Physics Book 19: Electronic Devices.
Practice MCQs: Chapter 1, Level 4 (new NEET pattern)
31. Match List I (quantity) with List II (SI unit).
List I: A. Current density; B. Mobility; C. Conductivity; D. Relaxation time
List II: (i) s; (ii) A m⁻²; (iii) m² V⁻¹ s⁻¹; (iv) S m⁻¹
(a) A-iii, B-ii, C-iv, D-i (b) A-ii, B-iii, C-iv, D-i (c) A-ii, B-iv, C-iii, D-i (d) A-i, B-iii, C-iv, D-ii
32. Match List I (quantity for copper at room temperature) with List II (order of magnitude).
List I: A. Relaxation time; B. Free-electron density; C. Drift speed for 1 A in a 1 mm² wire; D. Speed at which the electric field sets up along the wire
List II: (i) 10⁻⁴ m s⁻¹; (ii) 10⁸ m s⁻¹; (iii) 10⁻¹⁴ s; (iv) 10²⁹ m⁻³
(a) A-i, B-iv, C-iii, D-ii (b) A-iii, B-ii, C-i, D-iv (c) A-iv, B-iii, C-i, D-ii (d) A-iii, B-iv, C-i, D-ii
33. A copper wire is connected to a cell of fixed voltage V. Match the change in List I with its effect on drift speed in List II.
List I: A. Length doubled, same area; B. Area doubled, same length; C. Voltage doubled; D. Wire heated, same voltage
List II: (i) unchanged; (ii) doubles; (iii) decreases because τ falls; (iv) halves
(a) A-iv, B-i, C-ii, D-iii (b) A-i, B-iv, C-ii, D-iii (c) A-iv, B-ii, C-i, D-iii (d) A-iii, B-i, C-ii, D-iv
34. Match the situation in List I with the current in List II.
List I: A. 5 × 10¹⁸ electrons cross a section in 2 s; B. q = 3t² + 2t coulomb, at t = 1 s; C. A ring carrying 2 μC spins at 50 rev/s; D. Current density 2 × 10⁵ A m⁻² through 1 mm²
List II: (i) 8 A; (ii) 0.2 A; (iii) 0.4 A; (iv) 0.1 mA
(a) A-ii, B-i, C-iv, D-iii (b) A-iii, B-iv, C-i, D-ii (c) A-iii, B-i, C-iv, D-ii (d) A-i, B-iii, C-iv, D-ii
35. How many of the following statements are correct?
A. Drift velocity of electrons is opposite to the applied field.
B. Current density is a vector, but current is a scalar.
C. With no applied field, the average velocity of free electrons in a metal is zero.
D. Mobility of electrons in a metal increases when the metal is heated.
E. In a wire of non-uniform thickness carrying a steady current, drift speed is greatest at the thinnest part.
(a) 2 (b) 3 (c) 4 (d) 5
36. A steady current flows through a wire whose cross-section narrows along its length. Choose the correct set of statements.
A. The current is the same at every section.
B. The current density is the same at every section.
C. The electric field is larger in the thinner part.
D. The drift speed is the same at every section.
(a) A and B only (b) A and C only (c) B and D only (d) A, C and D only
37. Choose the correct set of statements about the relaxation time τ in a metal.
A. It is the average time between successive collisions of a free electron.
B. For copper at room temperature it is of the order of 10⁻¹⁴ s.
C. Conductivity is given by σ = ne²τ/m.
D. τ increases as the temperature rises.
(a) A and B only (b) A, B and C only (c) B, C and D only (d) A, B, C and D
38. How many of the following statements are correct?
A. 1 ampere equals 1 coulomb per second.
B. A current of 1.6 A means 10¹⁹ electrons cross a section each second.
C. The SI unit of mobility is m² V⁻¹ s⁻¹.
D. A ceiling fan starts at once because electrons travel from the switch to the fan at nearly the speed of light.
(a) 1 (b) 2 (c) 3 (d) 4
39. A graph of charge q (y-axis) through a wire against time t (x-axis) is a straight line from the origin to 12 C at t = 4 s. After that it stays flat at 12 C up to t = 6 s. The currents at t = 2 s and t = 5 s are
(a) 3 A and 0 (b) 3 A and 3 A (c) 6 A and 0 (d) 0 and 3 A
40. A current–time graph rises in a straight line from 0 to 4 A between t = 0 and t = 2 s. It stays at 4 A until t = 5 s, then falls in a straight line to zero at t = 6 s. The total charge that flows is
(a) 16 C (b) 20 C (c) 18 C (d) 24 C
41. Four wires of the same material carry currents as listed. In which wire is the drift speed greatest?
| Wire | Current (A) | Diameter (mm) |
|---|---|---|
| P | 2 | 1.0 |
| Q | 4 | 2.0 |
| R | 1 | 0.5 |
| S | 3 | 0.8 |
(a) P (b) Q (c) R (d) S
Passage for Q42–Q43: A home inverter uses a copper strip of cross-section 2 mm × 5 mm to carry 17 A from the battery. Take n = 8.5 × 10²⁸ m⁻³ and e = 1.6 × 10⁻¹⁹ C.
42. The drift speed of electrons in the strip is
(a) 1.25 × 10⁻⁴ m/s (b) 1.25 × 10⁻³ m/s (c) 2.5 × 10⁻⁴ m/s (d) 6.25 × 10⁻⁵ m/s
43. The time an electron takes to drift 1 m along the strip is about
(a) 800 s (b) 80 s (c) 1.25 × 10⁴ s (d) 8.0 × 10³ s
44. Two copper wires A and B are joined in series across a battery. The diameter of A is twice that of B. The ratios v_d(A) : v_d(B) and E_A : E_B are
(a) 4 : 1 and 1 : 4 (b) 1 : 4 and 1 : 4 (c) 1 : 2 and 1 : 2 (d) 1 : 4 and 4 : 1
45. In a metal, τ = 2.5 × 10⁻¹⁴ s and n = 8.5 × 10²⁸ m⁻³. Take m = 9.1 × 10⁻³¹ kg and e = 1.6 × 10⁻¹⁹ C. The electron mobility and the conductivity are about
(a) 4.4 × 10⁻³ m² V⁻¹ s⁻¹ and 6.0 × 10⁶ S/m (b) 2.2 × 10⁻³ m² V⁻¹ s⁻¹ and 3.0 × 10⁷ S/m (c) 4.4 × 10⁻³ m² V⁻¹ s⁻¹ and 6.0 × 10⁷ S/m (d) 8.8 × 10⁻³ m² V⁻¹ s⁻¹ and 1.2 × 10⁸ S/m
Level 4 answer key
| Q | Ans | Reason |
|---|---|---|
| 31 | b | J in A m⁻², μ in m² V⁻¹ s⁻¹, σ in S m⁻¹, τ in s |
| 32 | d | τ ~ 10⁻¹⁴ s, n ~ 10²⁹ m⁻³, v_d = 1/(neA) ≈ 7 × 10⁻⁵ m/s ~ 10⁻⁴, field sets up near light speed |
| 33 | a | v_d = μV/L: longer L halves it, area has no effect, double V doubles it, heating lowers τ |
| 34 | c | 5 × 10¹⁸ × 1.6 × 10⁻¹⁹/2 = 0.4 A; dq/dt = 6t + 2 = 8 A; qf = 10⁻⁴ A; JA = 0.2 A |
| 35 | c | A, B, C, E are correct; heating lowers τ, so mobility falls |
| 36 | b | I is constant; J = I/A and E = J/σ are larger where A is small; v_d ∝ 1/A |
| 37 | b | τ falls with temperature because collisions become more frequent |
| 38 | c | A, B, C are correct; the field, not the electrons, travels at nearly light speed |
| 39 | a | Slope of q-t is current: 12/4 = 3 A, then the flat part gives 0 |
| 40 | c | Area under I-t: 4 + 12 + 2 = 18 C |
| 41 | d | v_d ∝ I/d²: P 2, Q 1, R 4, S 4.69 |
| 42 | a | v_d = 17/(8.5 × 10²⁸ × 1.6 × 10⁻¹⁹ × 10⁻⁵) = 1.25 × 10⁻⁴ m/s |
| 43 | d | t = 1/(1.25 × 10⁻⁴) = 8000 s, over two hours |
| 44 | b | Same I, v_d ∝ 1/d² gives 1 : 4; E = J/σ also ∝ 1/d² |
| 45 | c | μ = eτ/m = 4.4 × 10⁻³; σ = neμ = 5.98 × 10⁷ S/m |