Chapter 10 of 12 · 24 min read

Chapter 8: Wheatstone Bridge and Metre Bridge

A Wheatstone bridge finds an unknown resistance by balancing it against known ones until a galvanometer reads zero. The metre bridge is the same idea built on a one-metre wire, and it is the version you use in the lab.

What you will learn

  • Derive the balance condition P/Q = R/S with Kirchhoff's laws.

  • Use the special properties of a balanced bridge to simplify networks.

  • Find the galvanometer current in an unbalanced bridge.

  • Find an unknown resistance and resistivity with a metre bridge.

  • Know the sources of error and why balance near the middle is best.

8.1 The Wheatstone bridge

Four resistors form a diamond ABCD: P from A to B, Q from B to C, R from A to D and S from D to C. A cell is connected across A and C. A galvanometer G is connected across B and D.

Figure 8.1 · Wheatstone bridge with arms P, Q, R, S
Figure 8.1 · Wheatstone bridge with arms P, Q, R, S

P and Q form the upper path from A to C, R and S the lower path, and the galvanometer G bridges the midpoints B and D.

The bridge is balanced when no current flows through G. Then B and D are at the same potential.

Derivation: with I_g = 0, the current I₁ through P also flows through Q, and the current I₂ through R also flows through S. Apply the loop rule to loop ABDA:

−I1P+I2R=0⇒I1P=I2R-I_1 P + I_2 R = 0 \quad\Rightarrow\quad I_1 P = I_2 R

Apply it to loop BCDB:

−I1Q+I2S=0⇒I1Q=I2S-I_1 Q + I_2 S = 0 \quad\Rightarrow\quad I_1 Q = I_2 S

Divide the first by the second:

PQ=RS\frac{P}{Q} = \frac{R}{S}

This is the balance condition. It does not involve the cell's emf or the galvanometer's resistance. If three arms are known, S = RQ/P.

8.2 Properties of a balanced bridge

  • No current flows in the B–D branch. You can remove it, or replace G by any resistor, and nothing else changes.

  • So the bridge becomes two series pairs in parallel. Its equivalent resistance between A and C is:

RAC=(P+Q)(R+S)P+Q+R+SR_{AC} = \frac{(P + Q)(R + S)}{P + Q + R + S}
  • Swapping the cell and the galvanometer keeps the bridge balanced.

  • Changing the cell's emf does not upset the balance.

  • The bridge is most sensitive when all four arms are of similar size.

When you see a diamond-shaped network in a question, check P/Q = R/S first. If it holds, delete the middle resistor and the problem becomes easy.

8.3 Unbalanced bridge

If P/Q is not equal to R/S, current flows through G. Its direction is from the higher of B and D to the lower. With A at potential V and C at zero, ignoring G for a quick check:

VB=VQP+Q,VD=VSR+SV_B = V\frac{Q}{P + Q}, \qquad V_D = V\frac{S}{R + S}

To find the actual galvanometer current, use the node method of Chapter 7 with V_B and V_D as unknowns.

8.4 The metre bridge

A metre bridge is a uniform wire AC, 1 m long, of an alloy such as constantan or manganin, stretched along a metre scale. Thick copper strips at the ends and in the middle leave two gaps. A known resistance R goes in the left gap and the unknown S in the right gap.

A galvanometer joins the middle strip (point B) to a sliding jockey D on the wire. A cell and key go across the ends of the wire.

Figure 8.2 · Metre bridge set-up
Figure 8.2 · Metre bridge set-up

The two lengths of wire on either side of the jockey act as the bridge's other two arms, so the balance length l fixes the ratio R : S.

The two parts of the wire act as the other two arms of the bridge. If the jockey balances at length l cm from the left end, the left part has resistance kl and the right part k(100 − l), where k is the resistance per cm. The balance condition gives:

RS=l100−l⇒S=R 100−ll\frac{R}{S} = \frac{l}{100 - l} \quad\Rightarrow\quad S = R\,\frac{100 - l}{l}

To find resistivity, measure the wire under test: length L and radius r. Then:

ρ=S πr2L\rho = \frac{S\,\pi r^2}{L}

8.5 Errors and good practice

Source of errorWhat it doesHow to reduce it
End resistance at the strips and jointsAdds unknown resistance at each endUse thick copper strips; interchange R and S and average
Non-uniform wireResistance not proportional to lengthUse a uniform alloy wire
Heating of the wireResistance drifts during the readingPress the key only while taking a reading
Balance near one endLarge percentage error in SChoose R so the balance falls near 50 cm

Why is the middle best? If the error in reading l is Δl, then:

ΔSS=Δl(1l+1100−l)=100 Δll(100−l)\frac{\Delta S}{S} = \Delta l\left(\frac{1}{l} + \frac{1}{100 - l}\right) = \frac{100\,\Delta l}{l(100 - l)}

The product l(100 − l) is largest at l = 50 cm, so the fractional error is smallest there.

After interchanging R and S, the new balance length is 100 − l.

Worked example 8.1: A bridge has P = 10 Ω, Q = 20 Ω and R = 15 Ω. Find S for balance.

Solution: S = RQ/P = 15 × 20/10 = 30 Ω.

Worked example 8.2: Four 4 Ω resistors form a bridge, with a 5 Ω galvanometer across the middle. Find the resistance across the cell terminals.

Solution: 4/4 = 4/4, so the bridge is balanced and the 5 Ω carries no current. R_AC = (8 × 8)/16 = 4 Ω.

Worked example 8.3: A bridge has P = 2 Ω, Q = 4 Ω, R = 3 Ω and S = 6 Ω, with a resistor in the middle branch. Find R_AC.

Solution: 2/4 = 3/6, so it is balanced. R_AC = (6 × 9)/15 = 3.6 Ω.

Worked example 8.4: An ideal 6 V cell is across A and C, with A positive. P = 1 Ω, Q = 2 Ω, R = 2 Ω, S = 1 Ω and the galvanometer is 1 Ω. Find the galvanometer current.

Solution: Take V_C = 0. Junction B: (6 − V_B)/1 = V_B/2 + (V_B − V_D)/1, giving 6 = 2.5V_B − V_D. Junction D: (6 − V_D)/2 + (V_B − V_D) = V_D/1, giving 3 + V_B = 2.5V_D. Solving, V_B = 24/7 V and V_D = 18/7 V. I_g = (24/7 − 18/7)/1 = 6/7 ≈ 0.86 A, from B to D.

Worked example 8.5: In a metre bridge, 4 Ω is in the left gap and balance is at 40 cm. Find the unknown resistance.

Solution: S = 4 × 60/40 = 6 Ω.

Worked example 8.6: The 6 Ω wire of Worked example 8.5 is 50 cm long with a radius of 0.2 mm. Find its resistivity.

Solution: ρ = 6 × π × (0.2 × 10⁻³)²/0.5 ≈ 1.5 × 10⁻⁶ Ω m. This is typical of an alloy like nichrome.

Worked example 8.7: A metre bridge balances at 40 cm with R in the left gap and S in the right. S is now shunted by an equal resistance. Find the new balance point.

Solution: R/S = 40/60, so R = 2S/3. The right gap becomes S/2. Now R/(S/2) = 4/3 = l/(100 − l). So 3l = 400 − 4l and l = 400/7 ≈ 57.1 cm.

Worked example 8.8: A metre bridge balances at 50 cm and the scale can be read to 0.1 cm. Find the percentage error in S.

Solution: ΔS/S = 0.1(1/50 + 1/50) = 0.004, which is 0.4 per cent. At l = 20 cm the same Δl gives 0.1(1/20 + 1/80) = 0.625 per cent.

Quick revision

  • Balance: P/Q = R/S, galvanometer current zero.

  • Balance does not depend on the emf or on G's resistance.

  • Balanced bridge: remove the middle branch; R_AC = (P + Q)(R + S)/(P + Q + R + S).

  • Swapping the cell and G keeps the balance.

  • Metre bridge: S = R(100 − l)/l, with R in the left gap.

  • Interchanging R and S moves balance to 100 − l.

  • Best accuracy with balance near 50 cm.

  • Thick strips and alloy wire cut errors.

NEET traps

  • Writing the balance as PQ = RS. It is P/Q = R/S, which is the same as PS = QR.

  • Using l and 100 − l the wrong way round. Match l with the gap on the same side.

  • Adding the galvanometer resistance into a balanced bridge's equivalent resistance.

  • Thinking a bigger emf changes the balance point.

  • Using copper for the bridge wire. It needs an alloy with high ρ and low α.

  • Forgetting that shunting a gap changes that gap's resistance before you re-balance.

Practice MCQs: Chapter 8

Level 1: Concept check

1. The balance condition of a Wheatstone bridge with arms P, Q, R, S (P and Q on one side) is (a) P/Q = R/S (b) PQ = RS (c) P/R = S/Q (d) P + Q = R + S

2. At balance, the current through the galvanometer is (a) maximum (b) equal to the cell current (c) half the cell current (d) zero

3. A Wheatstone bridge is most sensitive when (a) one arm is very large (b) all four arms have similar resistance (c) the galvanometer has zero resistance (d) the cell emf is very small

4. The metre bridge works on the principle of the (a) potentiometer (b) ammeter shunt (c) Wheatstone bridge (d) Joule heating effect

5. The wire of a metre bridge is usually made of (a) constantan or manganin (b) copper (c) iron (d) aluminium

6. Thick copper strips are used in a metre bridge to (a) increase the resistance (b) hold the wire tight (c) produce heat (d) keep the unaccounted strip resistance negligible

7. For best accuracy, the balance point should be (a) close to the 0 cm end (b) close to the 100 cm end (c) near the middle of the wire (d) anywhere; it makes no difference

8. In a balanced bridge, the cell and the galvanometer are interchanged. The bridge (a) becomes unbalanced (b) stays balanced (c) gives twice the galvanometer current (d) reverses the galvanometer current

9. In a metre bridge, R is in the left gap and balance is at l cm from the left end. The unknown S is (a) Rl/(100 − l) (b) R(100 + l)/l (c) Rl/100 (d) R(100 − l)/l

10. A bridge has P = 5 Ω, Q = 10 Ω and R = 8 Ω. For balance, S is (a) 16 Ω (b) 4 Ω (c) 6.25 Ω (d) 10 Ω

Level 2: NEET standard

11. A metre bridge has 3 Ω in the left gap and balances at 60 cm. The unknown resistance is (a) 4.5 Ω (b) 1.5 Ω (c) 2 Ω (d) 5 Ω

12. A bridge has all four arms 6 Ω and a 10 Ω galvanometer. The resistance across the cell terminals is (a) 6 Ω (b) 10 Ω (c) 3 Ω (d) 12 Ω

13. A metre bridge balances at 40 cm. R and S are interchanged. The new balance point is (a) 40 cm (b) 50 cm (c) 20 cm (d) 60 cm

14. A metre bridge has 5 Ω in the left gap and balances at 25 cm. The unknown resistance is (a) 5/3 Ω (b) 15 Ω (c) 20 Ω (d) 25 Ω

15. A bridge has P = 2 Ω, Q = 4 Ω, R = 3 Ω, S = 6 Ω and a 5 Ω resistor between B and D. The resistance between A and C is (a) 15 Ω (b) 2.5 Ω (c) 3.6 Ω (d) 4.5 Ω

16. A 1 m wire of cross-section 0.5 mm² is found to have 4 Ω resistance. Its resistivity is (a) 2 × 10⁻⁶ Ω m (b) 2 × 10⁻⁷ Ω m (c) 8 × 10⁻⁶ Ω m (d) 1.25 × 10⁻⁷ Ω m

17. A Wheatstone bridge is balanced. Which change keeps it balanced? (a) Changing P alone (b) Changing S alone (c) Changing the ratio P/Q alone (d) Changing the emf of the cell

18. A metre bridge has 2 Ω in the left gap and balances at 20 cm. The unknown resistance is (a) 0.5 Ω (b) 8 Ω (c) 10 Ω (d) 4 Ω

19. The percentage error in a metre bridge reading is least near the middle because (a) the wire resistance is highest there (b) the galvanometer current is largest there (c) end resistances vanish there (d) the term 1/l + 1/(100 − l) is least at l = 50 cm

20. A metre bridge balances at 50 cm and lengths are read to 0.1 cm. The percentage error in S is (a) 0.2 per cent (b) 0.1 per cent (c) 0.4 per cent (d) 0.8 per cent

21. A bridge has P = Q = R = 10 Ω and S = 12 Ω, with A positive and C at zero. Current in the galvanometer flows (a) from D to B (b) from B to D (c) nowhere; it is zero (d) back and forth

22. To balance the bridge of Q21, a resistance X is connected in parallel with S. X must be (a) 2 Ω (b) 10 Ω (c) 60 Ω (d) 120 Ω

Level 3: Challenge

23. A metre bridge balances at 40 cm with R in the left gap and S in the right. S is then shunted by an equal resistance. The new balance point is about (a) 40 cm (b) 57.1 cm (c) 50 cm (d) 66.7 cm

24. An ideal 10 V cell is across A and C. P = 2 Ω, Q = 3 Ω, R = 3 Ω, S = 2 Ω and the galvanometer is 1 Ω. The galvanometer current is (a) 0.5 A (b) 1 A (c) zero (d) 10/17 A

25. In a metre bridge with X in the left gap and Y in the right, balance is at 20 cm. When 12 Ω is added in series with X, balance moves to 50 cm. Y is (a) 16 Ω (b) 4 Ω (c) 12 Ω (d) 20 Ω

26. A network has A–B 1 Ω, B–C 2 Ω, A–D 2 Ω, D–C 4 Ω and B–D 5 Ω. The resistance between A and C is (a) 3 Ω (b) 6 Ω (c) 2 Ω (d) 1.5 Ω

27. A metre bridge gives 6 Ω for a wire 50 cm long of radius 0.2 mm. Its resistivity is about (a) 1.5 × 10⁻⁶ Ω m (b) 3.0 × 10⁻⁶ Ω m (c) 7.5 × 10⁻⁷ Ω m (d) 1.5 × 10⁻⁸ Ω m

28. In a balanced metre bridge, the cell and the galvanometer are interchanged. The balance point (a) moves to 100 − l (b) stays the same (c) moves to 50 cm (d) can no longer be found

29. Assertion (A): The connecting strips in a metre bridge are made of thick copper. Reason (R): Thick copper strips have negligible resistance, so they add almost no unaccounted resistance. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: A balanced Wheatstone bridge stays balanced if the galvanometer is replaced by a resistor. Statement II: In a metre bridge with R in the left gap, balance at 30 cm means S = 3R/7. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1aFrom I₁P = I₂R and I₁Q = I₂S
2dDefinition of balance
3bSimilar arms give largest response
4cWire parts act as two arms
5aHigh ρ, low α
6dStrip resistance must be tiny
7cLeast percentage error
8bReciprocity of the bridge
9dR/S = l/(100 − l)
10a8 × 10/5
11c3 × 40/60
12aBalanced: (12 × 12)/24
13d100 − 40
14b5 × 75/25
15cBalanced: (6 × 9)/15
16a4 × 0.5 × 10⁻⁶/1
17dBalance is independent of emf
18b2 × 80/20
19d100/[l(100 − l)] is least at 50
20c0.1 × (2/50)
21aV_D = 12/22 of V is above V_B = 1/2 of V
22c12X/(12 + X) = 10
23bR = 2S/3; 4/3 = l/(100 − l)
24dNode method: V_B = 90/17 V, V_D = 80/17 V
25aY = 4X and X + 12 = Y
26c1/2 = 2/4, balanced: (3 × 6)/9
27a6π(0.2 × 10⁻³)²/0.5
28bBalance condition unchanged
29aR gives the purpose of A
30cS = R × 70/30 = 7R/3

Chapter 8 revision sheet

One-page summary

  • A Wheatstone bridge has four arms P, Q, R, S, a cell across one diagonal and a galvanometer across the other.

  • Balance condition: P/Q = R/S. Then the two galvanometer ends are at the same potential and no current flows through it.

  • Balance does not depend on the cell's emf, the galvanometer resistance or any resistance in series with the cell.

  • In a balanced bridge, the galvanometer arm can be removed, shorted or replaced by any resistor without changing anything else.

  • Cell and galvanometer can be interchanged; the balance stays.

  • The bridge is most sensitive when all four arms have similar values. It is poor for very small resistances (lead and contact resistance) and very large ones.

  • If P/Q is not equal to R/S, find the potentials of the galvanometer ends; current flows from the higher to the lower one.

  • Metre bridge: a 1 m uniform wire forms two arms. Balance: R/S = l/(100 − l), with l in cm from the end next to R.

  • Resistivity from a metre bridge: ρ = S·πr²/L for the wire placed in the S gap.

  • Thick copper strips have negligible resistance; the bridge wire is manganin or constantan (high ρ, small α, uniform).

  • End error comes from extra resistance at the joints. Repeat with R and S interchanged and average.

  • The fractional error ΔS/S = 100Δl/[l(100 − l)] is smallest when l is near 50 cm.

  • Press the jockey gently, do not slide it while pressed, and pass current only while taking readings.

PQ=RS,RS=l100−l,ΔSS=100 Δll(100−l)\frac{P}{Q} = \frac{R}{S}, \quad \frac{R}{S} = \frac{l}{100 - l}, \quad \frac{\Delta S}{S} = \frac{100\,\Delta l}{l(100 - l)}

Must-remember table

ItemRule or value
Wheatstone balanceP/Q = R/S
Metre bridge balanceR/S = l/(100 − l)
Swap R and Snew l = 100 − l
Best null pointnear 50 cm
Bridge wire materialmanganin or constantan
Connecting stripsthick copper
Resistivity of test wireρ = Sπr²/L

Memory aids

  • "Pairs Quarrel Rarely Silently": P/Q = R/S, the balance ratio in order round the bridge.

  • "Middle gives Minimum error": a null point near 50 cm gives the least percentage error.

  • "Swap and Average": interchange R and S and average the results to cancel end error.

  • "Balanced? Bin the middle": in a balanced bridge, ignore the galvanometer arm.

Concept connections

  • The balance condition is proved with Kirchhoff's laws from Chapter 7 of this book.

  • The metre bridge is one of the listed practicals in Physics Book 20: Experimental Skills.

  • Percentage error in S uses the error rules from Physics Book 1: Physics and Measurement.

Practice MCQs: Chapter 8, Level 4 (new NEET pattern)

31. A metre bridge has R = 10 Ω in the left gap. Match the balance length l from the left end (List I) with the unknown S in the right gap (List II).

  • List I: A. 50 cm; B. 40 cm; C. 60 cm; D. 20 cm

  • List II: (i) 40 Ω; (ii) 20/3 Ω; (iii) 10 Ω; (iv) 15 Ω

(a) A-iv, B-iii, C-ii, D-i (b) A-iii, B-ii, C-iv, D-i (c) A-iii, B-iv, C-i, D-ii (d) A-iii, B-iv, C-ii, D-i

32. Match the feature of a metre bridge in List I with its purpose in List II.

  • List I: A. Thick copper strips; B. Bridge wire of manganin or constantan; C. Null point kept near the middle; D. Interchanging R and S and averaging

  • List II: (i) reduces the effect of end error; (ii) makes strip resistance negligible; (iii) small α, so the wire's resistance hardly changes when it warms; (iv) smallest percentage error

(a) A-iii, B-ii, C-iv, D-i (b) A-ii, B-iv, C-iii, D-i (c) A-ii, B-iii, C-iv, D-i (d) A-i, B-iii, C-iv, D-ii

33. Match the values of P, Q, R in List I with the value of S that balances the bridge in List II.

  • List I: A. 10 Ω, 20 Ω, 30 Ω; B. 5 Ω, 15 Ω, 4 Ω; C. 100 Ω, 10 Ω, 50 Ω; D. 3 Ω, 4 Ω, 6 Ω

  • List II: (i) 5 Ω; (ii) 8 Ω; (iii) 60 Ω; (iv) 12 Ω

(a) A-iv, B-iii, C-i, D-ii (b) A-iii, B-iv, C-i, D-ii (c) A-iii, B-i, C-iv, D-ii (d) A-ii, B-iv, C-i, D-iii

34. A bridge has P = 2 Ω, Q = 4 Ω, R = 3 Ω, S = 6 Ω and a 5 Ω galvanometer arm, driven by an ideal 9 V battery. Match List I with List II.

  • List I: A. Equivalent resistance; B. Battery current; C. Current in the galvanometer arm; D. Current through P

  • List II: (i) 1.5 A; (ii) 3.6 Ω; (iii) zero; (iv) 2.5 A

(a) A-ii, B-iv, C-iii, D-i (b) A-iv, B-ii, C-iii, D-i (c) A-ii, B-i, C-iii, D-iv (d) A-ii, B-iv, C-i, D-iii

35. How many of the following statements are correct?

  • A. At balance, no current flows through the galvanometer.

  • B. The balance condition does not depend on the emf of the cell.

  • C. Interchanging the cell and the galvanometer leaves the balance unchanged.

  • D. The balance condition depends on the galvanometer's resistance.

  • E. A metre bridge works on the Wheatstone bridge principle.

(a) 3 (b) 4 (c) 5 (d) 2

36. Choose the correct set of statements about a metre bridge experiment.

  • A. The jockey should be pressed gently and not slid while pressed.

  • B. Current should pass only while readings are being taken.

  • C. A null point at 5 cm gives a more accurate result than one at 50 cm.

  • D. The bridge wire should have a uniform cross-section.

(a) A and C only (b) B and C only (c) A, C and D only (d) A, B and D only

37. Choose the correct set of statements about the sensitivity and use of a Wheatstone bridge.

  • A. It is most sensitive when all four arms have similar resistances.

  • B. It cannot measure very small resistances accurately because of lead and contact resistance.

  • C. It is best suited for resistances like 0.001 Ω.

  • D. In a balanced bridge, the galvanometer arm can be replaced by any resistor without changing the equivalent resistance.

(a) A and C only (b) A, B and D only (c) C and D only (d) A, B, C and D

38. In a metre bridge, 4 Ω is in the left gap and the null point is at 40 cm. How many statements are correct?

  • A. The unknown resistance is 6 Ω.

  • B. If the two resistors are interchanged, the null point is at 60 cm.

  • C. If the unknown is shunted by another 6 Ω, the new null point is at about 57.1 cm.

  • D. Doubling the emf of the driving cell shifts the null point to 20 cm.

(a) 1 (b) 2 (c) 3 (d) 4

39. A student uses different known resistors R in the left gap with the same unknown S in the right gap. The unknown S, and the most reliable reading, are

R (Ω)l (cm)
225.0
440.0
650.0
857.1

(a) 4 Ω, the R = 2 Ω reading (b) 6 Ω, the R = 2 Ω reading (c) 8 Ω, the R = 8 Ω reading (d) 6 Ω, the R = 6 Ω reading

40. In bridge ABCD, P = AB = 10 Ω, Q = BC = 10 Ω, R = AD = 10 Ω and S = DC = 20 Ω. The cell makes A positive and C negative, and the galvanometer joins B and D. The direction of galvanometer current, and one way to balance the bridge, are

(a) B to D; change S to 40 Ω (b) D to B; connect 20 Ω in parallel with S (c) D to B; change P to 20 Ω (d) No current; the bridge is already balanced

41. For a metre bridge with a fixed S in the right gap, a graph of balance length l (y-axis) against R in the left gap (x-axis) passes through l = 50 cm at R = 5 Ω. The value of S and the balance length for R = 20 Ω are

(a) 5 Ω and 80 cm (b) 5 Ω and 20 cm (c) 10 Ω and 66.7 cm (d) 50 Ω and 28.6 cm

Passage for Q42–Q43: In the school lab, a wire 50 cm long with diameter 0.40 mm is placed in the right gap of a metre bridge. A 3 Ω resistor is in the left gap. The null point is found at 37.5 cm from the left end.

42. The resistance of the wire is

(a) 1.8 Ω (b) 3 Ω (c) 8 Ω (d) 5 Ω

43. The resistivity of the wire's material is about

(a) 1.26 × 10⁻⁶ Ω m (b) 5.03 × 10⁻⁶ Ω m (c) 1.26 × 10⁻⁷ Ω m (d) 2.51 × 10⁻⁶ Ω m

44. In a metre bridge the null point is at l = 25.0 cm, and l can be read to ±0.1 cm. The percentage error in the unknown S is about

(a) 0.40% (b) 0.53% (c) 0.13% (d) 0.27%

45. A balanced bridge has P = 4 Ω, Q = 8 Ω, R = 6 Ω, S = 12 Ω, and a 10 Ω galvanometer arm. An ideal 18 V battery drives it. The power used in Q is

(a) 9 W (b) 12 W (c) 18 W (d) 27 W

Level 4 answer key

QAnsReason
31dS = 10(100 − l)/l: 10, 15, 20/3, 40 Ω
32cStrips negligible, alloy wire stable, middle null least error, swapping cancels end error
33bS = QR/P: 60, 12, 5, 8 Ω
34aBalanced (2/4 = 3/6); (6 ∥ 9) = 3.6 Ω; I = 2.5 A; P–Q branch 9/6 = 1.5 A
35bA, B, C, E are correct; balance does not depend on galvanometer resistance
36dNull point near the middle gives the least error, so C is wrong
37bLead and contact resistance spoil readings of very small resistances, so C is wrong
38cS = 4 × 60/40 = 6 Ω; swap gives 60 cm; 4/3 = l/(100 − l) gives 57.1 cm; emf does not move the null point
39dEvery row gives S = R(100 − l)/l = 6 Ω; the 50 cm reading has the least error
40bV_B = V/2, V_D = 2V/3, so current flows D to B; 20 ∥ 20 = 10 Ω balances it
41al = 50 cm when R = S, so S = 5 Ω; l = 100 × 20/25 = 80 cm
42dS = 3 × 62.5/37.5 = 5 Ω
43aρ = 5 × π(0.2 × 10⁻³)²/0.5 = 1.26 × 10⁻⁶ Ω m
44b100 × 0.1/(25 × 75) = 0.0053, about 0.53%
45cP–Q branch current 18/12 = 1.5 A; 1.5² × 8 = 18 W
24 min left
‹
›