Chapter 7 of 12 · 23 min read

Chapter 5: Cells, EMF and Internal Resistance

A real cell is an ideal emf E with a small resistance r hidden inside it. That one picture explains why a torch dims as you draw more current and why a short circuit heats a battery.

What you will learn

  • Define emf and separate it from terminal potential difference.

  • Use V = E − Ir while discharging and V = E + Ir while charging.

  • Find E and r from graphs and from two readings.

  • Combine cells in series, in parallel and in mixed groups.

  • Apply the maximum power transfer theorem and find efficiency.

In this chapter E is the emf, r is the internal resistance, R is the external resistance and V is the terminal potential difference.

5.1 EMF of a cell

Inside a cell, chemical reactions push positive charge from the negative plate to the positive plate, against the field. The work the cell does per unit charge in doing this is its emf:

E=WqE = \frac{W}{q}

The unit is the volt. Despite its name, emf is not a force. It equals the potential difference between the terminals when no current is drawn, that is, on open circuit. A good voltmeter across an unused cell reads its emf, very nearly.

5.2 Internal resistance and terminal voltage

Current inside the cell must pass through the electrolyte. This gives the cell an internal resistance r. It depends on:

  • the nature and concentration of the electrolyte,

  • the distance between the plates (more distance, more r),

  • the area of the plates dipped in it (more area, less r),

  • the temperature (warmer electrolyte, less r).

It does not depend on the external circuit.

With an external resistance R, the total resistance is R + r:

I=ER+rI = \frac{E}{R + r}

The potential difference across the terminals is what is left after the drop inside:

V=E−Ir=ERR+rV = E - Ir = \frac{ER}{R + r}
Figure 5.1 · A cell of emf E and internal resistance r driving current through R
Figure 5.1 · A cell of emf E and internal resistance r driving current through R

The dashed box is the real cell: an ideal emf E in series with r. Only what is left after the drop Ir appears across its terminals and across R.

Three special cases:

  • Open circuit (I = 0): V = E.

  • Short circuit (R = 0): I = E/r, the largest possible current, and V = 0.

  • Charging (current forced into the + terminal): V = E + Ir, so V is more than E.

The V-I graph of a discharging cell is a straight line. It meets the V axis at E. Its slope is −r. It meets the I axis at the short-circuit current E/r.

From two readings you can find r. If the cell reads E on open circuit and V across R:

r=R(EV−1)r = R\left(\frac{E}{V} - 1\right)

5.3 Cells in series

Join the + of one cell to the − of the next. The emfs add and the internal resistances add:

Eeq=E1+E2+…,req=r1+r2+…E_{eq} = E_1 + E_2 + \dots, \qquad r_{eq} = r_1 + r_2 + \dots

If a cell is put in the wrong way round, its emf subtracts but its internal resistance still adds. With n identical cells and m of them reversed:

Eeq=(n−2m)E,req=nrE_{eq} = (n - 2m)E, \qquad r_{eq} = nr

5.4 Cells in parallel

Join all + terminals together and all − terminals together. For two cells:

Eeq=E1r2+E2r1r1+r2,req=r1r2r1+r2E_{eq} = \frac{E_1 r_2 + E_2 r_1}{r_1 + r_2}, \qquad r_{eq} = \frac{r_1 r_2}{r_1 + r_2}

Derivation in brief: with terminal voltage V, the cell currents are I₁ = (E₁ − V)/r₁ and I₂ = (E₂ − V)/r₂. Adding them, I = (E₁/r₁ + E₂/r₂) − V(1/r₁ + 1/r₂). Rearranging into V = E_eq − I r_eq gives the results above.

For n identical cells in parallel, the emf stays E and the internal resistance becomes r/n.

Grouping of n identical cellsE_eqr_eqCurrent through RBest when
SeriesnEnrnE/(R + nr)R much larger than r
ParallelEr/nE/(R + r/n)R much smaller than r
m rows of n in seriesnEnr/mnE/(R + nr/m)R = nr/m gives the most current

If R = r, series and parallel give the same current.

5.5 Mixed grouping

Arrange N = mn identical cells in m parallel rows, each row having n cells in series. The current through R is:

I=nER+nrm=mnEmR+nrI = \frac{nE}{R + \dfrac{nr}{m}} = \frac{mnE}{mR + nr}

For fixed mn, the denominator mR + nr is smallest when mR = nr. So the current is largest when the external resistance equals the internal resistance of the group: R = nr/m.

5.6 Maximum power transfer

The power delivered to R is:

P=I2R=E2R(R+r)2P = I^2 R = \frac{E^2 R}{(R + r)^2}

Set dP/dR = 0. This gives (R + r) − 2R = 0, so R = r. The maximum power is:

Pmax=E24rP_{max} = \frac{E^2}{4r}

Efficiency is useful power over total power:

η=I2RI2(R+r)=RR+r=VE\eta = \frac{I^2 R}{I^2(R + r)} = \frac{R}{R + r} = \frac{V}{E}

At maximum power, η = 50 per cent and V = E/2. Half the energy is wasted as heat in the cell. A phone charger or a power station is not run at maximum power transfer; it is run at high efficiency instead.

If the same power is delivered to two different resistances R₁ and R₂, then r = √(R₁R₂).

Worked example 5.1: A 12 V battery with internal resistance 0.5 Ω drives a 5.5 Ω lamp. Find the current and the terminal voltage.

Solution: I = 12/(5.5 + 0.5) = 2 A. V = 12 − 2 × 0.5 = 11 V.

Worked example 5.2: A cell reads 1.5 V on open circuit and 1.25 V across a 2.5 Ω resistor. Find its internal resistance.

Solution: r = R(E/V − 1) = 2.5(1.5/1.25 − 1) = 2.5 × 0.2 = 0.5 Ω.

Worked example 5.3: A 12 V car battery of internal resistance 0.4 Ω is being charged with a current of 5 A. What is its terminal voltage?

Solution: While charging, V = E + Ir = 12 + 5 × 0.4 = 14 V. The charger must supply more than 12 V.

Worked example 5.4: A cell's V-I graph meets the V axis at 6 V and the I axis at 3 A. Find E and r.

Solution: E = 6 V. The short-circuit current E/r = 3 A, so r = 2 Ω.

Worked example 5.5: Six cells, each 1.5 V and 0.2 Ω, are joined in series to a 4.8 Ω resistor. One cell is put in the wrong way round. Find the current.

Solution: E_eq = (6 − 2) × 1.5 = 6 V. r_eq = 6 × 0.2 = 1.2 Ω. I = 6/(4.8 + 1.2) = 1 A.

Worked example 5.6: A 2 V cell (r = 1 Ω) and a 4 V cell (r = 2 Ω) are joined in parallel, like terminals together, across a 2 Ω resistor. Find the current in the resistor.

Solution: E_eq = (2 × 2 + 4 × 1)/3 = 8/3 V. r_eq = 2/3 Ω. I = (8/3)/(2 + 2/3) = (8/3)/(8/3) = 1 A.

Worked example 5.7: You have 24 cells, each 2 V with r = 0.5 Ω, and an external resistance of 3 Ω. How should you arrange them for the largest current, and what is it?

Solution: Need mn = 24 and nr/m = R, so 0.5n = 3m, giving n = 6m. Then 6m² = 24, m = 2 and n = 12. Two rows of 12 cells. I = 12 × 2/(3 + 3) = 4 A.

Worked example 5.8: A source has E = 10 V and r = 2 Ω. Find the largest power it can deliver to a load and the efficiency then.

Solution: Choose R = r = 2 Ω. P_max = 100/(4 × 2) = 12.5 W. Efficiency = 2/4 = 50 per cent.

Worked example 5.9: A cell delivers the same power to a 2 Ω resistor and to an 8 Ω resistor. Find its internal resistance.

Solution: E² × 2/(2 + r)² = E² × 8/(8 + r)². Taking square roots, (8 + r) = 2(2 + r), so r = 4 Ω. This matches r = √(2 × 8).

Quick revision

  • Emf is work per unit charge; it equals terminal voltage on open circuit.

  • I = E/(R + r). Discharging: V = E − Ir. Charging: V = E + Ir.

  • Short circuit: I = E/r, V = 0.

  • Series: emfs add, r adds; a reversed cell subtracts 2E.

  • Parallel (two cells): E_eq = (E₁r₂ + E₂r₁)/(r₁ + r₂), r_eq = r₁r₂/(r₁ + r₂).

  • Mixed grouping: largest current when R = nr/m.

  • Maximum power when R = r: P_max = E²/4r, efficiency 50 per cent.

  • Equal power in R₁ and R₂ means r = √(R₁R₂).

NEET traps

  • Writing V = E − Ir for a cell being charged. It is E + Ir.

  • Subtracting the internal resistance of a reversed cell. Only its emf subtracts.

  • Adding emfs of cells in parallel.

  • Thinking efficiency is highest at maximum power. It is only 50 per cent there.

  • Saying internal resistance depends on the external load.

  • Reading slope of the V-I graph as +r. It is −r.

Practice MCQs: Chapter 5

Level 1: Concept check

1. The emf of a cell is (a) a force (b) the work done by the cell per unit charge (c) the current it gives (d) the power it gives

2. The terminal voltage of a cell delivering current I is (a) E + Ir (b) E (c) Ir (d) E − Ir

3. The internal resistance of a cell does NOT depend on (a) the external resistance (b) the nature of the electrolyte (c) the distance between the plates (d) the temperature

4. The short-circuit current of a cell of emf E and internal resistance r is (a) Er (b) zero (c) E/r (d) r/E

5. The terminal voltage of a cell equals its emf when (a) it is being charged (b) it is short-circuited (c) it gives its largest current (d) no current is drawn

6. n identical cells (E, r) in series have (a) emf E, resistance r/n (b) emf nE, resistance nr (c) emf nE, resistance r/n (d) emf E, resistance nr

7. n identical cells (E, r) in parallel have (a) emf nE, resistance nr (b) emf nE, resistance r/n (c) emf E, resistance r/n (d) emf E, resistance nr

8. A cell gives the largest power to an external resistance R when (a) R = r (b) R = 2r (c) R = r/2 (d) R is very large

9. At maximum power transfer, the efficiency is (a) 100 per cent (b) 50 per cent (c) 25 per cent (d) 75 per cent

10. A 2 V cell with r = 1 Ω is connected to 3 Ω. The current is (a) 2 A (b) 0.67 A (c) 1 A (d) 0.5 A

Level 2: NEET standard

11. A cell reads 1.6 V on open circuit and 1.2 V across a 3 Ω resistor. Its internal resistance is (a) 0.5 Ω (b) 2 Ω (c) 3 Ω (d) 1 Ω

12. A 6 V battery with r = 0.5 Ω is being charged with 2 A. Its terminal voltage is (a) 7 V (b) 5 V (c) 6 V (d) 8 V

13. A cell's V-I graph meets the V axis at 4.5 V and the I axis at 1.5 A. Its internal resistance is (a) 4.5 Ω (b) 1.5 Ω (c) 3 Ω (d) 6.75 Ω

14. Eight cells, each 1.5 V and 0.25 Ω, are in series across 4 Ω. Two cells are reversed. The current is (a) 2 A (b) 1 A (c) 1.5 A (d) 0.75 A

15. A 3 V cell (r = 1 Ω) and a 6 V cell (r = 2 Ω) are joined in parallel, like terminals together. The equivalent emf is (a) 4 V (b) 4.5 V (c) 9 V (d) 3 V

16. A 12 V source with r = 3 Ω can deliver at most (a) 48 W (b) 24 W (c) 6 W (d) 12 W

17. A cell gives the same power to a 4 Ω resistor and to a 9 Ω resistor. Its internal resistance is (a) 5 Ω (b) 6 Ω (c) 6.5 Ω (d) 13 Ω

18. A 2 V cell with r = 0.5 Ω delivers 0.8 A. Its terminal voltage is (a) 2.4 V (b) 2 V (c) 1.6 V (d) 0.4 V

19. For a discharging cell, the graph of terminal voltage V against current I is (a) a straight line of negative slope, with V-intercept E (b) a straight line of positive slope (c) a hyperbola (d) a horizontal line

20. n identical cells give the same current through R whether joined in series or in parallel. Then (a) R = nr (b) R = r/n (c) R = n²r (d) R = r

21. A cell with r = 1 Ω supplies a 4 Ω resistor. The efficiency is (a) 20 per cent (b) 25 per cent (c) 80 per cent (d) 75 per cent

22. Twelve cells, each 2 V and 1 Ω, are arranged in 3 parallel rows of 4 cells in series, across 2 Ω. The current in the 2 Ω resistor is (a) 2 A (b) 2.4 A (c) 3 A (d) 4 A

Level 3: Challenge

23. Sixteen cells, each 1.5 V and 0.5 Ω, are to drive the largest current through 2 Ω. That largest current is (a) 2 A (b) 3 A (c) 4 A (d) 6 A

24. A cell gives a terminal voltage of 4 V across 2 Ω and 5 V across 5 Ω. Its emf is (a) 6 V (b) 5 V (c) 7 V (d) 4.5 V

25. A cell of internal resistance r is connected to R = 3r. The power in R, as a fraction of the maximum possible, is (a) 1/2 (b) 1/4 (c) 9/16 (d) 3/4

26. A 10 V battery (r = 1 Ω) is charged from a 15 V supply through a 4 Ω resistor. The terminal voltage of the battery during charging is (a) 10 V (b) 9 V (c) 11 V (d) 15 V

27. A battery of 10 identical cells (E, r) in series has one cell reversed. Its emf and internal resistance are (a) 8E, 10r (b) 9E, 9r (c) 8E, 8r (d) 10E, 10r

28. A 6 V cell (r = 1 Ω) and a 3 V cell (r = 2 Ω) are joined in parallel, like terminals together, with no external load. The common terminal voltage is (a) 4.5 V (b) 5 V (c) 4 V (d) 6 V

29. Assertion (A): The terminal voltage of a cell is always less than its emf. Reason (R): When a cell is being charged, its terminal voltage is E + Ir. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: When a cell delivers maximum power to a load, its terminal voltage is half its emf. Statement II: The internal resistance of a cell does not depend on the external resistance. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1bE = W/q
2dDrop Ir inside the cell
3ar is a property of the cell
4cR = 0, I = E/r
5dNo current, no internal drop
6bBoth add
7cSame emf, r shared
8adP/dR = 0 at R = r
9bR/(R + r) = 1/2
10d2/4
11d3(1.6/1.2 − 1) = 1 Ω
12a6 + 2 × 0.5
13c4.5/1.5
14bE = 4 × 1.5 = 6 V, r = 2 Ω, 6/6
15a(3 × 2 + 6 × 1)/3
16d144/12
17br = √(4 × 9)
18c2 − 0.8 × 0.5
19aV = E − Ir
20dnE/(R + nr) = E/(R + r/n) gives R = r
21c4/5
22b8/(2 + 4/3) = 2.4 A
23bm = 2, n = 8: 12/(2 + 2)
24a4(2 + r) = 2E and 5 + r = E give r = 1, E = 6
25d3r/(4r)² ÷ 1/(4r) = 3/4
26cI = 5/5 = 1 A, V = 10 + 1
27a(10 − 2)E, r still adds
28bCirculating 1 A; 6 − 1 = 5 V
29dFalse on charging; R is true
30aV = E/2 at R = r; r is internal

Chapter 5 revision sheet

One-page summary

  • EMF E is the work done by the source per unit charge in taking it once round the complete circuit. It is the terminal voltage on open circuit.

  • Internal resistance r opposes current inside the cell. It grows as the cell ages and with lower electrolyte concentration.

  • Current with external R: I = E/(R + r).

  • Terminal voltage while discharging: V = E − Ir. While charging: V = E + Ir. Ir is the "lost volts".

  • Open circuit: V = E. Short circuit: V = 0 and I = E/r (maximum current).

  • Finding r from a voltmeter: r = R(E/V − 1).

  • V-I graph of a cell is a straight line: y-intercept E, slope −r, x-intercept E/r.

  • n identical cells in series: I = nE/(R + nr). One cell reversed: net emf (n − 2)E, resistance still nr.

  • n identical cells in parallel: E_eq = E, r_eq = r/n, I = E/(R + r/n).

  • Mixed grouping (m rows of n in series): I = mnE/(mR + nr); maximum when R = nr/m.

  • Two different cells in parallel: E_eq = (E_1r_2 + E_2r_1)/(r_1 + r_2), r_eq = r_1r_2/(r_1 + r_2).

  • Maximum power to R when R = r: P_max = E²/4r, efficiency 50%.

  • Efficiency in general: η = V/E = R/(R + r).

I=ER+r,V=E−Ir,Pmax=E24r,Imixed=mnEmR+nrI = \frac{E}{R + r}, \quad V = E - Ir, \quad P_{max} = \frac{E^2}{4r}, \quad I_{mixed} = \frac{mnE}{mR + nr}

Must-remember table

SituationE_eqr_eqCurrent in R
Single cellErE/(R + r)
n in seriesnEnrnE/(R + nr)
n in series, one reversed(n − 2)Enr(n − 2)E/(R + nr)
n in parallelEr/nnE/(nR + r)
m rows of n in seriesnEnr/mmnE/(mR + nr)
Two unlike cells in parallel(E_1r_2 + E_2r_1)/(r_1 + r_2)r_1r_2/(r_1 + r_2)E_eq/(R + r_eq)

Memory aids

  • "Dis-charge, Dip; Re-charge, Rise": discharging V = E − Ir, charging V = E + Ir.

  • "Match to Max": match R to r for maximum power; you get only half the energy (50% efficiency).

  • "One wrong costs two": one reversed cell in a series string takes away 2E from the net emf.

  • "Short gives E over r": the short-circuit current of a cell is E/r.

Concept connections

  • EMF is work per unit charge, building on potential in Physics Book 11: Electrostatics.

  • Chemical reactions that set up a cell's emf are covered in Chemistry Book 7: Redox Reactions and Electrochemistry.

  • The maximum power idea returns for matching loads in Physics Book 14: Electromagnetic Induction and Alternating Currents.

Practice MCQs: Chapter 5, Level 4 (new NEET pattern)

31. A cell of emf 12 V and internal resistance 2 Ω is used. Match List I with List II.

  • List I: A. Current through an external 4 Ω; B. Terminal voltage with 4 Ω connected; C. Short-circuit current; D. Maximum power that can be given to an external resistor

  • List II: (i) 8 V; (ii) 6 A; (iii) 18 W; (iv) 2 A

(a) A-iv, B-i, C-ii, D-iii (b) A-i, B-iv, C-ii, D-iii (c) A-iv, B-ii, C-i, D-iii (d) A-iv, B-i, C-iii, D-ii

32. Identical cells (emf E, internal resistance r) send current through an external R. Match the arrangement in List I with the current in List II.

  • List I: A. n cells in series; B. n cells in parallel; C. n cells in series with one cell reversed; D. m parallel rows, each of n cells in series

  • List II: (i) nE/(nR + r); (ii) mnE/(mR + nr); (iii) nE/(R + nr); (iv) (n − 2)E/(R + nr)

(a) A-i, B-iii, C-iv, D-ii (b) A-iii, B-i, C-iv, D-ii (c) A-iii, B-iv, C-i, D-ii (d) A-ii, B-i, C-iv, D-iii

33. Match the condition of a cell (emf E, internal resistance r, current I) in List I with its terminal voltage in List II.

  • List I: A. Open circuit; B. Short circuit; C. Discharging with current I; D. Being charged with current I

  • List II: (i) E + Ir; (ii) E; (iii) E − Ir; (iv) zero

(a) A-iii, B-iv, C-ii, D-i (b) A-ii, B-i, C-iii, D-iv (c) A-ii, B-iv, C-i, D-iii (d) A-ii, B-iv, C-iii, D-i

34. Cell 1 has E_1 = 6 V, r_1 = 1 Ω; cell 2 has E_2 = 3 V, r_2 = 2 Ω. Match List I with List II.

  • List I: A. Net emf in series, aiding; B. Net emf in series, opposing; C. Internal resistance of the series pair; D. Equivalent emf in parallel (like terminals together)

  • List II: (i) 5 V; (ii) 9 V; (iii) 3 Ω; (iv) 3 V

(a) A-ii, B-iv, C-iii, D-i (b) A-iv, B-ii, C-iii, D-i (c) A-ii, B-iii, C-iv, D-i (d) A-i, B-iv, C-iii, D-ii

35. How many of the following statements are correct?

  • A. EMF is the work done by the source per unit charge in taking it once round the complete circuit.

  • B. The terminal voltage of a discharging cell is less than its emf.

  • C. The emf of a cell depends on the external resistance.

  • D. The internal resistance of a cell increases as it ages.

  • E. While a cell is being charged, its terminal voltage is more than its emf.

(a) 2 (b) 3 (c) 4 (d) 5

36. A cell of emf E and internal resistance r delivers power to an external resistor R. Choose the correct set of statements.

  • A. Power in R is maximum when R = r.

  • B. The maximum power is E²/4r.

  • C. The efficiency at maximum power is 50%.

  • D. The efficiency at maximum power is 100%.

(a) A, B and C only (b) A and D only (c) B and C only (d) A, B and D only

37. Choose the correct set of statements for a cell connected to a variable external resistor R.

  • A. As R increases, I decreases and V increases.

  • B. As R becomes very large, V approaches E.

  • C. As R becomes zero, V approaches E.

  • D. The lost volts inside the cell equal Ir.

(a) A and C only (b) A, B and D only (c) B and C only (d) A, B, C and D

38. Four identical cells, each 1.5 V and 0.5 Ω, are in series with an external 4 Ω resistor. How many statements are correct?

  • A. The current is 1 A.

  • B. The voltage across the external resistor is 4 V.

  • C. If one cell is reversed, the current becomes 0.5 A.

  • D. The power wasted inside the battery is 2 W.

(a) 1 (b) 2 (c) 3 (d) 4

39. The terminal voltage V (y-axis) of a cell against current I (x-axis) is a straight line from V = 9 V at I = 0 down to V = 0 at I = 4.5 A. The emf and internal resistance are

(a) 9 V, 0.5 Ω (b) 4.5 V, 2 Ω (c) 9 V, 2 Ω (d) 4.5 V, 0.5 Ω

40. A voltmeter across a cell reads these values for two external resistors. The emf and internal resistance are

R (Ω)V (V)
21.00
51.25

(a) 1.25 V, 1 Ω (b) 1.5 V, 1 Ω (c) 1.5 V, 0.5 Ω (d) 2.0 V, 2 Ω

41. The graph of power P in an external resistor against its resistance R rises, peaks at R = 3 Ω where P = 12 W, and then falls. The emf and internal resistance of the source are

(a) 12 V, 3 Ω (b) 6 V, 3 Ω (c) 12 V, 6 Ω (d) 24 V, 3 Ω

Passage for Q42–Q43: A car battery has emf 12 V and internal resistance 0.05 Ω. On a cold winter morning the starter motor draws 100 A. Later the battery is put on a charger that pushes 20 A into it.

42. The terminal voltage while the starter motor runs is

(a) 12 V (b) 17 V (c) 5 V (d) 7 V

43. The terminal voltage while it is being charged is

(a) 13 V (b) 11 V (c) 12 V (d) 14 V

44. Twenty-four cells, each of emf 2 V and internal resistance 1 Ω, are to send the largest possible current through an external 6 Ω resistor. The best grouping and the current are

(a) 6 rows of 4 cells, 2 A (b) 2 rows of 12 cells, 4 A (c) 2 rows of 12 cells, 2 A (d) 4 rows of 6 cells, 1.5 A

45. Cell 1 (2 V, 1 Ω) and cell 2 (1 V, 1 Ω) are connected in parallel with like terminals together, and the pair drives a 1.5 Ω resistor. The current in the resistor is

(a) 1.5 A (b) 0.75 A (c) 1.0 A (d) 0.5 A

Level 4 answer key

QAnsReason
31a12/6 = 2 A; 12 − 4 = 8 V; 12/2 = 6 A; 144/8 = 18 W
32bSeries adds E and r; parallel divides r by n; a reversed cell removes 2E; mixed gives mnE/(mR + nr)
33dOpen E, short zero, discharging E − Ir, charging E + Ir
34a6 + 3 = 9 V; 6 − 3 = 3 V; 1 + 2 = 3 Ω; (6 × 2 + 3 × 1)/3 = 5 V
35cA, B, D, E are correct; emf does not depend on R
36aAt R = r half the power is lost inside, so efficiency is 50%
37bAt R = 0, V = 0, so C is wrong
38dI = 6/(4 + 2) = 1 A; V = 4 V; reversed: 3/6 = 0.5 A; I² × 2 = 2 W. All four correct
39cE = 9 V (y-intercept); r = 9/4.5 = 2 Ω
40b1 = 2E/(2 + r) and 1.25 = 5E/(5 + r) give r = 1 Ω, E = 1.5 V
41aPeak at R = r = 3 Ω; E²/(4 × 3) = 12 gives E = 12 V
42d12 − 100 × 0.05 = 7 V
43a12 + 20 × 0.05 = 13 V
44cNeed nr/m = 6 with mn = 24, so n = 12, m = 2; I = 48/(12 + 12) = 2 A
45bE_eq = (2 + 1)/2 = 1.5 V, r_eq = 0.5 Ω; I = 1.5/2 = 0.75 A
23 min left
‹
›