Chapter 5 of 12 · 21 min read

Chapter 3: Temperature Dependence of Resistance

Heat a metal and its resistance rises. Heat a semiconductor and its resistance falls. One formula, ρ = m/(ne²τ), explains both.

What you will learn

  • Explain why metals and semiconductors respond to heat in opposite ways.

  • Use R = R₀(1 + αΔT) and define the temperature coefficient α.

  • Read ρ-T graphs for metals and semiconductors.

  • Know why alloys like manganin and nichrome are chosen for special jobs.

  • Find the effective α of series and parallel combinations.

3.1 Why temperature matters

Recall from Chapter 2:

ρ=mne2τ\rho = \frac{m}{ne^2\tau}

Temperature can change n (how many carriers there are) or τ (how long they travel between collisions).

In a metal, n is fixed by the atoms. Heating makes the ions vibrate harder, so electrons collide more often. τ falls, so ρ rises.

In a semiconductor, heating frees many more charge carriers. n rises sharply, far faster than τ falls. So ρ falls.

Think of a crowded railway platform at rush hour. More jostling (vibrating ions) slows each commuter. But if many more gates open (more carriers), the total flow can still go up.

3.2 Temperature coefficient of resistance

For metals over a moderate range of temperature, resistivity rises almost linearly:

ρT=ρ0[1+α(T−T0)]\rho_T = \rho_0\left[1 + \alpha (T - T_0)\right]

If the size of the wire hardly changes, the same holds for resistance:

RT=R0[1+α(T−T0)]R_T = R_0\left[1 + \alpha (T - T_0)\right]

α is the temperature coefficient of resistivity. It is the fractional change in resistance per degree:

α=RT−R0R0 (T−T0)\alpha = \frac{R_T - R_0}{R_0\,(T - T_0)}

Its unit is K⁻¹ or °C⁻¹. Both give the same number, since a step of 1 K equals a step of 1 °C. For metals α is positive. For semiconductors and carbon it is negative.

When R₀ is given at 0 °C and you know R at two other temperatures t₁ and t₂, use the exact ratio:

R1R2=1+αt11+αt2\frac{R_1}{R_2} = \frac{1 + \alpha t_1}{1 + \alpha t_2}

For small α and a small range, the quick form R₂ ≈ R₁[1 + α(t₂ − t₁)] is close enough. If a question names 0 °C as the reference, use the exact form.

3.3 Graphs of ρ against T

For a metal, the ρ-T graph is close to a straight line with a positive slope over a wide range. At very low temperatures it bends and levels off at a small leftover value. This residual resistivity comes from impurities and defects.

For a semiconductor, ρ falls steeply, roughly exponentially, as T rises.

Figure 3.1 · Resistivity against temperature for a metal and a semiconductor
Figure 3.1 · Resistivity against temperature for a metal and a semiconductor

The metal's curve levels off at a small residual value when cold and rises almost linearly when warm; the semiconductor's curve falls steeply as T rises.

Material typeExampleαMain effect of heating
Pure metalCopper, about 4 × 10⁻³ °C⁻¹Positive, fairly largeτ falls
AlloyNichrome, about 1.7 × 10⁻⁴ °C⁻¹Positive, smallτ falls slightly
AlloyManganin, about 2 × 10⁻⁶ °C⁻¹Positive, very smallAlmost no change
SemiconductorSiliconNegativen rises sharply
Non-metalCarbonNegativen rises

3.4 Uses of alloys

Alloys such as manganin, constantan and nichrome have a high resistivity and a low α. This suits two jobs:

  • Standard resistors and resistance boxes use manganin or constantan, because their value barely drifts with room temperature.

  • Heater coils in an electric iron or immersion rod use nichrome. Its high resistivity gives a lot of resistance in a short coil, and it does not oxidise easily when red hot.

Tungsten filaments have a positive α. A cold filament has a much lower resistance than a glowing one. So a bulb draws its largest current at the instant it is switched on, which is when old bulbs usually fuse.

3.5 Effective α of combinations

Take two resistors R₁ and R₂ (measured at the reference temperature) with coefficients α₁ and α₂.

In series, R = R₁(1 + α₁ΔT) + R₂(1 + α₂ΔT). Comparing with (R₁ + R₂)(1 + αΔT):

αseries=R1α1+R2α2R1+R2\alpha_{series} = \frac{R_1\alpha_1 + R_2\alpha_2}{R_1 + R_2}

In parallel, for small αΔT, the same method gives:

αparallel=R1α2+R2α1R1+R2\alpha_{parallel} = \frac{R_1\alpha_2 + R_2\alpha_1}{R_1 + R_2}

Note the swap of subscripts in the parallel case. For two equal resistors, both reduce to the average (α₁ + α₂)/2.

To make a series pair whose total does not change with temperature, set R₁α₁ + R₂α₂ = 0. One material must have a negative α, such as carbon.

3.6 Resistance thermometer

The steady rise of a platinum wire's resistance with temperature makes it a thermometer. If R₀, R₁₀₀ and R_t are the resistances at 0 °C, 100 °C and the unknown t:

t=Rt−R0R100−R0×100 ∘Ct = \frac{R_t - R_0}{R_{100} - R_0} \times 100\ ^{\circ}\mathrm{C}

Worked example 3.1: A copper coil has resistance 10 Ω at 0 °C. Take α = 4 × 10⁻³ °C⁻¹. Find its resistance at 50 °C.

Solution: R = 10(1 + 4 × 10⁻³ × 50) = 10 × 1.2 = 12 Ω.

Worked example 3.2: A wire has resistance 5 Ω at 0 °C and 6 Ω at 50 °C. Find α.

Solution: α = (6 − 5)/(5 × 50) = 4 × 10⁻³ °C⁻¹.

Worked example 3.3: A wire reads 50 Ω at 20 °C and 60 Ω at 70 °C. Taking 0 °C as reference, find α and the resistance at 0 °C.

Solution: 50/60 = (1 + 20α)/(1 + 70α). So 60 + 1200α = 50 + 3500α, giving α = 10/2300 ≈ 4.35 × 10⁻³ °C⁻¹. Then R₀ = 50/(1 + 20α) = 50/1.087 ≈ 46 Ω. The quick form would give 4.0 × 10⁻³, which is close but not exact.

Worked example 3.4: A platinum thermometer reads 5.00 Ω at 0 °C, 5.39 Ω at 100 °C and 5.795 Ω in a hot oil bath. Find the bath temperature.

Solution: t = (5.795 − 5.00)/(5.39 − 5.00) × 100 = 0.795/0.39 × 100 ≈ 204 °C.

Worked example 3.5: A tungsten filament has resistance 40 Ω at 20 °C. When glowing it has 440 Ω. Taking α = 4.5 × 10⁻³ °C⁻¹ with 20 °C as reference, estimate the filament temperature.

Solution: 440 = 40[1 + 4.5 × 10⁻³ ΔT]. So 4.5 × 10⁻³ ΔT = 10 and ΔT ≈ 2222 °C. Filament temperature ≈ 2242 °C. The cold filament takes 11 times the running current at switch-on.

Worked example 3.6: A carbon resistor (α = −5 × 10⁻⁴ °C⁻¹) and an iron wire (α = 5 × 10⁻³ °C⁻¹) in series must give 11 Ω at every temperature. Find each resistance.

Solution: R_C × 5 × 10⁻⁴ = R_Fe × 5 × 10⁻³, so R_C = 10 R_Fe. With R_C + R_Fe = 11 Ω: R_Fe = 1 Ω and R_C = 10 Ω.

Worked example 3.7: Resistors of 2 Ω (α = 4 × 10⁻³ °C⁻¹) and 3 Ω (α = 1 × 10⁻³ °C⁻¹) are joined in series. Find the effective α.

Solution: α = (2 × 4 + 3 × 1) × 10⁻³ / 5 = 2.2 × 10⁻³ °C⁻¹.

Quick revision

  • Metals: τ falls on heating, ρ rises, α is positive.

  • Semiconductors: n rises on heating, ρ falls, α is negative.

  • R_T = R₀(1 + αΔT); α has unit °C⁻¹ or K⁻¹.

  • With 0 °C as reference: R₁/R₂ = (1 + αt₁)/(1 + αt₂).

  • Manganin, constantan: standard resistors. Nichrome: heaters.

  • Series α = (R₁α₁ + R₂α₂)/(R₁ + R₂); parallel swaps the subscripts.

  • Bulbs draw the largest current at switch-on.

NEET traps

  • Saying metals get more free electrons when hot. n stays fixed; τ falls.

  • Using the quick form when the question fixes 0 °C as reference.

  • Thinking α in °C⁻¹ and K⁻¹ are different numbers.

  • Using the series formula for α when the resistors are in parallel.

  • Forgetting that heater coils need high resistivity, not low.

  • Reporting ΔT as the final temperature. Add the starting temperature.

Practice MCQs: Chapter 3

Level 1: Concept check

1. When a metal wire is heated, its resistance (a) decreases (b) stays the same (c) first decreases, then increases (d) increases

2. When a semiconductor is heated, its resistivity (a) increases (b) decreases (c) stays the same (d) becomes zero

3. The main reason the resistivity of a metal rises with temperature is that (a) the relaxation time decreases (b) the number of free electrons rises (c) the electron mass rises (d) the electron charge falls

4. The SI unit of temperature coefficient of resistance is (a) Ω K⁻¹ (b) Ω m K⁻¹ (c) K⁻¹ (d) K

5. The material best suited for standard resistors is (a) copper (b) manganin (c) silicon (d) tungsten

6. For a semiconductor, the temperature coefficient of resistance is (a) positive (b) zero (c) infinite (d) negative

7. The resistivity of a semiconductor falls on heating because (a) the number of charge carriers rises sharply (b) the relaxation time rises sharply (c) the lattice stops vibrating (d) electrons become heavier

8. Nichrome is used in heater coils because it has (a) low resistivity and high α (b) a low melting point (c) high resistivity and low α (d) zero resistivity

9. Near room temperature, the ρ-T graph of a metal is (a) an exponential fall (b) a parabola through the origin (c) a horizontal line (d) nearly a straight line with positive slope

10. A coil has R₀ = 10 Ω at 0 °C and α = 0.004 °C⁻¹. Its resistance at 100 °C is (a) 10.4 Ω (b) 14 Ω (c) 4 Ω (d) 40 Ω

Level 2: NEET standard

11. A wire has resistance 4 Ω at 0 °C and 5 Ω at 100 °C. Its α is (a) 2.5 × 10⁻³ °C⁻¹ (b) 2.0 × 10⁻³ °C⁻¹ (c) 2.5 × 10⁻² °C⁻¹ (d) 4 × 10⁻³ °C⁻¹

12. A copper coil has 50 Ω at 0 °C and α = 4 × 10⁻³ °C⁻¹. Its resistance becomes 60 Ω at (a) 25 °C (b) 40 °C (c) 50 °C (d) 100 °C

13. A platinum thermometer reads 4.0 Ω at 0 °C, 4.6 Ω at 100 °C and 4.9 Ω in a furnace. The furnace temperature is (a) 75 °C (b) 150 °C (c) 125 °C (d) 200 °C

14. A carbon resistor (α = −4 × 10⁻⁴ °C⁻¹) and a copper wire (α = 4 × 10⁻³ °C⁻¹) in series give 22 Ω at all temperatures. The carbon resistor is (a) 2 Ω (b) 11 Ω (c) 10 Ω (d) 20 Ω

15. A 3 Ω resistor (α = 2 × 10⁻³ °C⁻¹) is in series with a 1 Ω resistor (α = 6 × 10⁻³ °C⁻¹). The effective α is (a) 3 × 10⁻³ °C⁻¹ (b) 4 × 10⁻³ °C⁻¹ (c) 8 × 10⁻³ °C⁻¹ (d) 2 × 10⁻³ °C⁻¹

16. Two equal resistors with coefficients α₁ and α₂ are joined in parallel. The effective coefficient is (a) α₁ + α₂ (b) α₁α₂/(α₁ + α₂) (c) (α₁ + α₂)/2 (d) √(α₁α₂)

17. A filament bulb draws its largest current (a) after it reaches full brightness (b) halfway to full brightness (c) equally at all times (d) at the instant it is switched on

18. A heater element has 100 Ω at 0 °C and α = 2 × 10⁻⁴ °C⁻¹. At 500 °C its resistance is (a) 101 Ω (b) 110 Ω (c) 200 Ω (d) 150 Ω

19. As a typical metal is cooled towards very low temperatures, its resistivity (a) becomes zero for every metal (b) becomes infinite (c) levels off at a small residual value (d) becomes negative

20. A copper wire has 30 Ω at 0 °C and α = 4 × 10⁻³ °C⁻¹. Its resistance doubles at (a) 250 °C (b) 500 °C (c) 125 °C (d) 400 °C

21. The R-T graph of a pure semiconductor is (a) a straight line with positive slope (b) a horizontal line (c) a rising curve (d) a falling curve

22. Which pair has high resistivity and a very small temperature coefficient? (a) Copper and aluminium (b) Manganin and constantan (c) Silicon and germanium (d) Silver and gold

Level 3: Challenge

23. A wire has 50 Ω at 20 °C and 60 Ω at 70 °C. Taking R = R₀(1 + αt) with R₀ at 0 °C, α is about (a) 4.3 × 10⁻³ °C⁻¹ (b) 4.0 × 10⁻³ °C⁻¹ (c) 3.3 × 10⁻³ °C⁻¹ (d) 5.0 × 10⁻³ °C⁻¹

24. A tungsten filament has 30 Ω at 20 °C and 300 Ω when glowing. With α = 4.5 × 10⁻³ °C⁻¹ and 20 °C as reference, the filament temperature is (a) 2000 °C (b) 1980 °C (c) 2020 °C (d) 4020 °C

25. A 2 Ω resistor (α = 4 × 10⁻³ °C⁻¹) and a 6 Ω resistor (α = 1 × 10⁻³ °C⁻¹) are joined in parallel. The effective α is (a) 1.75 × 10⁻³ °C⁻¹ (b) 3.25 × 10⁻³ °C⁻¹ (c) 2.5 × 10⁻³ °C⁻¹ (d) 5.0 × 10⁻³ °C⁻¹

26. On heating a metal, its relaxation time falls by 20 per cent while n stays fixed. Its resistivity rises by (a) 20 per cent (b) 80 per cent (c) 120 per cent (d) 25 per cent

27. A coil across a fixed potential difference draws 2 A at 0 °C. Its α is 5 × 10⁻³ °C⁻¹. At 100 °C it draws (a) 3 A (b) 2 A (c) 1.33 A (d) 1.5 A

28. A wire of resistance R₀ is stretched to twice its length and then heated so that αΔT = 0.25. Its resistance becomes (a) 5R₀ (b) 4R₀ (c) 2.5R₀ (d) 1.25R₀

29. Assertion (A): The resistance of a semiconductor decreases as its temperature rises. Reason (R): In a semiconductor, the relaxation time of carriers increases with temperature. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: Manganin is used in standard resistors because its resistance hardly changes with temperature. Statement II: Nichrome has a much higher resistivity than copper. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1dτ falls, so R rises
2bCarrier density rises
3aMore collisions, shorter τ
4cα = ΔR/(R₀ΔT)
5bVery small α
6dR falls as T rises
7an rises sharply
8cLarge R in short coil, stable value
9dρ rises nearly linearly
10b10(1 + 0.4) = 14 Ω
11a1/(4 × 100)
12c10 = 50 × 0.004 × t
13b(0.9/0.6) × 100
14dR_C = 10 R_Cu, total 22 gives 20 and 2
15a(3 × 2 + 1 × 6)/4 × 10⁻³
16cEqual R: average of α
17dCold filament has least R
18b100(1 + 0.1) = 110 Ω
19cImpurities leave residual ρ
20a1 + 0.004t = 2
21dNegative α
22bAlloys for standard resistors
23aExact ratio gives 10/2300
24cΔT = 9/(4.5 × 10⁻³) = 2000; add 20
25b(2 × 1 + 6 × 4)/8 × 10⁻³
26dρ ∝ 1/τ: 1/0.8 = 1.25
27cR rises 1.5 times, I = 2/1.5
28a4 × 1.25 = 5
29cτ falls; n rises
30aBoth are standard facts

Chapter 3 revision sheet

One-page summary

  • Over a limited range, R_T = R_0(1 + αΔT) and ρ_T = ρ_0(1 + αΔT).

  • Temperature coefficient α = ΔR/(R_0ΔT), unit K⁻¹ or °C⁻¹ (same number).

  • For two temperatures: R_2/R_1 = (1 + αt_2)/(1 + αt_1), with R_0 at 0 °C as reference.

  • Metals: α is positive, about a few times 10⁻³ per °C. Heating makes collisions more frequent, so τ falls and ρ rises; n stays nearly constant.

  • Semiconductors (Si, Ge, carbon): α is negative. Heating frees many more carriers, so n rises steeply and ρ falls.

  • Alloys such as nichrome, manganin and constantan have high ρ and very small α.

  • Manganin and constantan are used for standard resistors; nichrome for heating elements.

  • Thermistors are semiconductor devices with a large α, usually negative (NTC), used as temperature sensors.

  • Superconductors lose all resistance below a critical temperature; mercury does this near 4.2 K.

  • A tungsten filament has much lower resistance when cold, so the current at switch-on is larger than the running current.

  • Series pair with zero net temperature coefficient: R_1α_1 + R_2α_2 = 0 (one α must be negative).

  • Series pair in general: α_eq = (R_1α_1 + R_2α_2)/(R_1 + R_2).

RT=R0(1+αΔT),α=RT−R0R0ΔTR_T = R_0(1 + \alpha \Delta T), \quad \alpha = \frac{R_T - R_0}{R_0 \Delta T}

Must-remember table

Material typeSign of αTypical size of αMain reasonUse
Pure metal (Cu, Al, W)Positive~10⁻³ per °Cτ fallsWires, filaments
Alloy (manganin, constantan)PositiveVery small, ~10⁻⁵ or lessDisordered latticeStandard resistors
NichromePositive~10⁻⁴ per °CHigh ρ, does not oxidiseHeating elements
Semiconductor (Si, Ge, C)NegativeLargen risesThermistors, devices
Superconductor below T_c—R = 0Special stateStrong magnets

Memory aids

  • "Metal Plus, Semi Minus": metals have positive α, semiconductors negative α.

  • "MaCo stays calm": Manganin and Constantan hardly change resistance with temperature, so they make standard resistors.

  • "Nichrome Never Cools": nichrome is the heating-element alloy.

  • "Mercury at Four": mercury becomes a superconductor near 4 K (4.2 K).

Concept connections

  • Collisions and τ come from the drift model in Chapter 1 of this book and from Physics Book 9: Kinetic Theory of Gases (random thermal motion).

  • Why semiconductor carrier density rises with temperature is explained in Physics Book 19: Electronic Devices.

  • Heating of wires by current links to thermal expansion and heat ideas in Physics Book 8: Thermodynamics.

Practice MCQs: Chapter 3, Level 4 (new NEET pattern)

31. Match the material in List I with its behaviour in List II.

  • List I: A. Copper; B. Manganin; C. Germanium; D. Mercury below 4.2 K

  • List II: (i) resistance drops to zero; (ii) negative α; (iii) positive α of about 10⁻³ per K; (iv) very small α, used in standard resistors

(a) A-iv, B-iii, C-ii, D-i (b) A-iii, B-iv, C-ii, D-i (c) A-iii, B-ii, C-iv, D-i (d) A-i, B-iv, C-ii, D-iii

32. A wire has R_0 = 10 Ω at 0 °C and α = 4 × 10⁻³ per °C. Match the temperature in List I with its resistance in List II.

  • List I: A. 50 °C; B. 100 °C; C. 250 °C; D. −50 °C

  • List II: (i) 12 Ω; (ii) 8 Ω; (iii) 20 Ω; (iv) 14 Ω

(a) A-i, B-iv, C-iii, D-ii (b) A-iv, B-i, C-iii, D-ii (c) A-i, B-iii, C-iv, D-ii (d) A-ii, B-iv, C-iii, D-i

33. Match the quantity in List I with how it changes as temperature rises, in List II.

  • List I: A. Relaxation time in a metal; B. Free-electron density in a metal; C. Resistivity of a metal; D. Charge-carrier density in a semiconductor

  • List II: (i) increases roughly linearly; (ii) decreases; (iii) increases very rapidly; (iv) stays nearly constant

(a) A-ii, B-i, C-iv, D-iii (b) A-iv, B-ii, C-i, D-iii (c) A-ii, B-iv, C-i, D-iii (d) A-ii, B-iv, C-iii, D-i

34. Match the use in List I with the best material in List II.

  • List I: A. Heating element of an electric iron; B. Standard resistance coil; C. Fuse wire; D. House wiring

  • List II: (i) tin–lead alloy; (ii) nichrome; (iii) copper; (iv) manganin

(a) A-iv, B-ii, C-i, D-iii (b) A-ii, B-iv, C-i, D-iii (c) A-ii, B-i, C-iv, D-iii (d) A-iii, B-iv, C-i, D-ii

35. How many of the following statements are correct?

  • A. The resistance of a metal wire rises with temperature.

  • B. The resistance of pure silicon falls with temperature.

  • C. The α of nichrome is much smaller than that of copper.

  • D. An NTC thermistor has a negative temperature coefficient.

  • E. In metals, the number of free electrons rises sharply with temperature.

(a) 4 (b) 3 (c) 5 (d) 2

36. Choose the correct set of statements about superconductors.

  • A. Below the critical temperature, the resistance becomes zero.

  • B. Mercury becomes superconducting near 4.2 K.

  • C. A superconductor has a negative resistance.

  • D. A current set up in a superconducting ring can keep flowing without a battery.

(a) A and B only (b) A, B and C only (c) C and D only (d) A, B and D only

37. Choose the correct set of statements.

  • A. R_T = R_0(1 + αΔT) works well for metals over a limited temperature range.

  • B. The unit of α is K⁻¹ (or °C⁻¹).

  • C. The α of a semiconductor is negative.

  • D. The α of every material is positive.

(a) A only (b) A and D only (c) B and C only (d) A, B and C only

38. How many of the following statements about a tungsten bulb filament are correct?

  • A. Its cold resistance is less than its hot resistance.

  • B. At switch-on, the current is larger than the steady running current.

  • C. Its resistance stays constant because tungsten is ohmic at all temperatures.

  • D. The switch-on surge is one reason bulbs often fuse at the moment they are switched on.

(a) 2 (b) 3 (c) 4 (d) 1

39. Three resistivity–temperature curves are described. Curve 1: ρ has a small non-zero value near 0 K and rises roughly linearly at higher T. Curve 2: ρ is very large at low T and falls steeply as T rises. Curve 3: ρ drops suddenly to zero at a few kelvin. The materials are

(a) 1 copper, 2 silicon, 3 mercury (b) 1 silicon, 2 copper, 3 mercury (c) 1 mercury, 2 silicon, 3 copper (d) 1 copper, 2 mercury, 3 silicon

40. A coil gives these readings. Taking 20 °C as the reference, its temperature coefficient is

T (°C)R (Ω)
2050.0
6057.6
10065.2

(a) 7.6 × 10⁻³ per °C (b) 1.9 × 10⁻³ per °C (c) 3.8 × 10⁻³ per °C (d) 4.4 × 10⁻³ per °C

41. The R-T graph of a wire is a straight line with R = 20 Ω at 0 °C and R = 28 Ω at 100 °C. The temperature at which R = 25 Ω is

(a) 62.5 °C (b) 50 °C (c) 75 °C (d) 125 °C

Passage for Q42–Q43: A platinum resistance thermometer has R = 100 Ω at 0 °C. Take α = 3.9 × 10⁻³ per °C and assume R varies linearly. A student uses it in a hill-station kitchen and in a cold-storage room.

42. In boiling water in the kitchen it reads 137.05 Ω. The temperature of the boiling water is

(a) 100 °C (b) 37 °C (c) 98.5 °C (d) 95 °C

43. In the cold-storage room at −40 °C its resistance is

(a) 96.1 Ω (b) 115.6 Ω (c) 84.4 Ω (d) 61.0 Ω

44. A 6 Ω metal resistor with α = 4 × 10⁻³ per °C is joined in series with a carbon resistor with α = −5 × 10⁻⁴ per °C. For the total resistance to stay constant with small changes in temperature, the carbon resistor must be

(a) 12 Ω (b) 24 Ω (c) 6 Ω (d) 48 Ω

45. A tungsten filament has resistance 40 Ω at 20 °C and 480 Ω when glowing. Take α = 4.5 × 10⁻³ per °C with 20 °C as reference, and assume a linear law. The filament temperature is about

(a) 1220 °C (b) 2464 °C (c) 2667 °C (d) 3200 °C

Level 4 answer key

QAnsReason
31bCopper positive α; manganin tiny α; germanium negative α; Hg superconducts below 4.2 K
32a10(1 + 0.2) = 12; 10(1.4) = 14; 10(2.0) = 20; 10(0.8) = 8 Ω
33cτ falls, n of metal nearly fixed, ρ of metal rises linearly, n of semiconductor rises steeply
34bNichrome heats, manganin is stable, tin–lead melts easily, copper conducts best
35aA, B, C, D are correct; n in metals stays nearly constant
36dResistance becomes zero, never negative
37dSemiconductors have negative α, so D is wrong
38bA, B, D are correct; tungsten's R rises a lot when hot
39aMetal rises linearly, semiconductor falls steeply, mercury superconducts
40c(57.6 − 50)/(50 × 40) = 3.8 × 10⁻³; the 100 °C reading gives the same
41aα = 8/(20 × 100) = 4 × 10⁻³; 25 = 20(1 + 0.004t) gives t = 62.5 °C
42dt = (1.3705 − 1)/0.0039 = 95 °C (water boils below 100 °C at height)
43cR = 100(1 − 0.0039 × 40) = 84.4 Ω
44d6 × 4 × 10⁻³ = R × 5 × 10⁻⁴ gives R = 48 Ω
45b12 = 1 + 4.5 × 10⁻³ΔT gives ΔT = 2444 °C, so T ≈ 2464 °C
21 min left
‹
›