Chapter 4 of 12 · 28 min read

Chapter 2: Lenz's Law, Motional EMF and Eddy Currents

What you will learn

  • How Lenz's law fixes the direction of an induced current, and why it follows from energy conservation.

  • Motional emf e = Bvl, derived two ways: from flux and from the force on charges.

  • The sliding rod on rails: current, magnetic drag, power and terminal velocity.

  • The emf of a rod or disc rotating in a field: e = ½Bωl².

  • Eddy currents: where they come from, how to reduce them, and where we use them.

2.1 Lenz's law

Faraday's law gives the size of the emf. Lenz's law (1834) gives its direction:

The induced current flows in such a direction that it opposes the change in flux that produces it.

Notice the word change. The induced current does not oppose the flux. It opposes the change.

  • Flux through a loop increasing: the induced current makes a field opposite to the applied field.

  • Flux decreasing: the induced current makes a field along the applied field, trying to keep the flux up.

Take a bar magnet with its N-pole moving towards a coil. The flux into the coil grows. The coil reacts by making its near face an N-pole, which repels the magnet. Seen from the magnet's side, a face with anticlockwise current is an N-pole. So the current is anticlockwise as seen from the magnet.

Figure 2.1 · Lenz's law: N-pole approaching a coil
Figure 2.1 · Lenz's law: N-pole approaching a coil

The coil's near face becomes an N-pole to repel the incoming magnet, so seen from the magnet the induced current runs anticlockwise.

Pull the magnet away and the near face becomes an S-pole. It now attracts the magnet, again opposing the motion. Either way, you must do work against the coil's push or pull. That work appears as electrical energy, and finally as heat in the coil.

Why Lenz's law must be true. Suppose the induced current helped the change. Then a tiny push on the magnet would increase the current, which would pull the magnet faster, which would increase the current further. Energy would appear from nowhere. That breaks conservation of energy. So Lenz's law is the law of energy conservation applied to induction. This is also the meaning of the minus sign in e = −N dΦ/dt.

A quick method for Lenz problems

  1. Find the direction of the applied field through the loop.

  2. Decide whether the flux is increasing or decreasing.

  3. Increasing: induced field is opposite. Decreasing: induced field is along.

  4. Use the right-hand thumb rule (thumb along induced field, fingers curl along current).

2.2 Motional emf: the rod on rails

Place two parallel metal rails a distance l apart, joined at one end through a resistor R. A uniform field B points into the page. A metal rod lies across the rails and slides to the right with speed v.

Figure 2.2 · Rod sliding on rails in a field into the page
Figure 2.2 · Rod sliding on rails in a field into the page

As the rod moves right the enclosed area and the into-page flux grow, so the induced current runs anticlockwise and the force on the rod points against v.

Derivation from flux. Let x be the distance of the rod from the resistor end. The enclosed area is lx, so Φ = Blx. The rod moves, so dx/dt = v:

e=dΦdt=Bldxdt=Blve = \frac{d\Phi}{dt} = Bl\frac{dx}{dt} = Blv

Derivation from force on charges. Each free electron in the rod moves with the rod at speed v. The Lorentz force qvB acts along the rod. Charges pile up at the ends until the electric field they make balances the magnetic push: qE = qvB, so E = vB. The potential difference across length l is El = Bvl. Both routes give the same answer.

If the rod's velocity makes an angle with the rod, or the rod is bent, use the effective length: the straight-line distance between the ends, measured perpendicular to v (and to B). A semicircular wire of radius r moving perpendicular to its diameter has e = B(2r)v.

Current, drag force and power. The circuit resistance is R, so:

I=BvlR,Fmag=BIl=B2l2vRI = \frac{Bvl}{R}, \qquad F_{mag} = BIl = \frac{B^2l^2v}{R}

By Lenz's law, this force on the current-carrying rod points against v. It is a drag. To keep v constant you must push with an equal force F. Your power input is:

P=Fv=B2l2v2R=I2RP = Fv = \frac{B^2l^2v^2}{R} = I^2R

The mechanical power you put in equals the heat produced in R. Energy is conserved, just as Lenz's law demands.

Terminal velocity. Suppose a constant force F pulls the rod, starting from rest. The drag grows with speed. The rod speeds up until drag equals F. Then:

vt=FRB2l2v_t = \frac{FR}{B^2l^2}

For a rod of mass m sliding down vertical rails (field horizontal, perpendicular to the rails' plane), F = mg, so v_t = mgR/(B²l²).

Rod given a push and then left alone. The only force is drag, m dv/dt = −B²l²v/R. Writing dv/dt = v dv/dx gives m dv = −(B²l²/R) dx. So the rod stops after a distance x = mv0R/(B²l²). All its kinetic energy, ½mv0², turns into heat.

2.3 Rotating rod and rotating disc

A metal rod of length l rotates with angular speed ω about one end, in a plane perpendicular to a uniform field B. Different parts of the rod move at different speeds. A small piece dr at distance r from the pivot moves at speed ωr, so its emf is B(ωr)dr. Add up all pieces:

e=∫0lBωr dr=12Bωl2e = \int_0^l B\omega r\,dr = \frac{1}{2}B\omega l^2

Another way: in one revolution (time 2π/ω) the rod sweeps area πl². So e = Bπl² ÷ (2π/ω) = ½Bωl².

  • A metal disc of radius r rotating about its axis gives the same emf between centre and rim: ½Bωr². This is Faraday's disc, a simple DC generator.

  • A rod rotating about its midpoint: each half gives ½Bω(l/2)², both pointing outward from the centre. The two ends are at the same potential, so the emf between the ends is zero.

  • Ceiling-fan blades rotating in the vertical component of the Earth's field have a tiny emf between hub and tip.

2.4 Eddy currents

Induced currents are not limited to wires. Whenever a solid piece of metal sits in a changing flux, or moves through a field, loops of current swirl inside it. These are eddy currents (also called Foucault currents), named for their likeness to eddies in a river.

By Lenz's law, eddy currents oppose the motion or change that causes them. They also heat the metal (I²R loss).

Reducing eddy currents. Large loops of current need a large continuous metal path. Break the path and the loops shrink.

  • Make transformer and motor cores from thin, insulated sheets (lamination). The insulating layer blocks current between sheets.

  • Cut slots in a moving metal plate. A slotted pendulum swings much longer through a magnet than a solid one.

  • Use materials of high resistivity, such as ferrites, at high frequencies.

Uses of eddy currents

ApplicationHow eddy currents help
Magnetic braking (metro trains, some roller coasters)Strong magnets near the rails or wheels set up eddy currents that oppose motion; smooth braking with no rubbing
Electromagnetic damping in galvanometersCoil wound on a metal frame; eddy currents stop the needle quickly at its reading (dead-beat galvanometer)
Induction furnaceHigh-frequency AC heats and melts metal by eddy currents; used to make alloys
Induction cooktopAC in a coil under the glass makes eddy currents in the vessel base, which heats the food
Electric power meters and speedometersA rotating aluminium disc or cup is dragged by eddy currents in proportion to current or speed

A magnet dropped through a vertical copper pipe falls slowly, at an acceleration much less than g. Through a PVC pipe it falls freely. The difference is eddy currents in the copper.

Worked example 2.1: A bar magnet is held with its S-pole facing a coil and is pulled away. Find the direction of the induced current, seen from the magnet.

Solution: Moving the S-pole away reduces the flux. The coil tries to keep the magnet close, so its near face must attract an S-pole: it becomes an N-pole. An N-face has anticlockwise current when seen from outside. So the current is anticlockwise as seen from the magnet.

Worked example 2.2: A rod 0.5 m long slides at 4 m/s on rails in a 0.2 T field perpendicular to the plane. The circuit resistance is 2 Ω. Find the emf, current, the force needed to keep the speed constant, and the power.

Solution: e = Bvl = 0.2 × 4 × 0.5 = 0.4 V. I = 0.4/2 = 0.2 A. F = BIl = 0.2 × 0.2 × 0.5 = 0.02 N. P = Fv = 0.08 W. Check: I²R = 0.04 × 2 = 0.08 W.

Worked example 2.3: An aircraft with wingspan 30 m flies level at 250 m/s. The vertical component of the Earth's field there is 4 × 10⁻⁵ T. Find the emf between the wing tips.

Solution: Only the vertical component cuts the wings in level flight. e = Bvl = 4 × 10⁻⁵ × 250 × 30 = 0.3 V. This cannot drive a current through a meter on board, because the meter's leads move with the plane and get the same emf.

Worked example 2.4: A semicircular wire of radius 10 cm moves at 2 m/s perpendicular to its diameter, in a 0.5 T field perpendicular to its plane. Find the emf between its ends.

Solution: Effective length = diameter = 0.2 m. e = 0.5 × 2 × 0.2 = 0.2 V. The curved length (πr) is not used.

Worked example 2.5: A copper rod 1 m long rotates about one end at 20 rad/s in a plane perpendicular to a 0.5 T field. Find the emf between its ends.

Solution: e = ½Bωl² = 0.5 × 0.5 × 20 × 1 = 5 V.

Worked example 2.6: A ceiling fan has blades 0.6 m long and turns at 300 rpm. The vertical component of the Earth's field is 3 × 10⁻⁵ T. Find the emf between the hub and a blade tip.

Solution: ω = 2π × 300/60 = 10π rad/s. e = ½ × 3 × 10⁻⁵ × 10π × (0.6)² = 1.7 × 10⁻⁴ V, about 0.17 mV. Far too small to notice.

Worked example 2.7: A rod of mass 20 g and length 0.5 m slides down smooth vertical rails joined by a 0.5 Ω resistor. A horizontal field of 0.4 T is perpendicular to the plane of the rails. Find the terminal velocity. (g = 10 m/s²)

Solution: v_t = mgR/(B²l²) = 0.02 × 10 × 0.5 / (0.16 × 0.25) = 0.1/0.04 = 2.5 m/s.

Worked example 2.8 (NEET-hard): A constant force of 0.5 N pulls a rod of length 0.5 m along smooth rails in a 1 T field. The circuit resistance is 2 Ω. Find the terminal velocity and the current then. Check energy.

Solution: v_t = FR/(B²l²) = 0.5 × 2 / (1 × 0.25) = 4 m/s. I = Bv_tl/R = 1 × 4 × 0.5 / 2 = 1 A. Power input Fv_t = 2 W. Heat I²R = 1 × 2 = 2 W. They match.

Quick revision

  • Lenz: induced current opposes the change in flux. It is energy conservation in action.

  • Motional emf e = Bvl (B, v, l mutually perpendicular). Use effective length for bent wires.

  • Rod on rails: I = Bvl/R, drag F = B²l²v/R, power B²l²v²/R.

  • Terminal velocity v_t = FR/(B²l²); vertical rails F = mg.

  • Rotating rod about one end or disc: e = ½Bωl². About midpoint: zero between ends.

  • Eddy currents heat and drag; reduce with laminations and slots; used in braking, damping, furnaces, cooktops, meters.

NEET traps

  • Saying the induced current opposes the flux. It opposes the change in flux.

  • Using the arc length of a curved wire in Bvl. Use the straight distance between the ends.

  • Writing Bωl² for a rotating rod and forgetting the ½.

  • Forgetting that a rod moving along B, or along its own length, has zero emf.

  • Thinking a rod rotating about its centre gives an emf between its ends. It gives zero.

  • Thinking eddy currents are always unwanted. Brakes, dampers and cooktops depend on them.

Practice MCQs: Chapter 2

Level 1: Concept check

1. Lenz's law is a consequence of the conservation of (a) charge (b) momentum (c) energy (d) mass

2. The induced current in a closed loop flows in a direction that (a) aids the change in flux (b) opposes the change in flux (c) is always clockwise (d) is always along the field

3. A rod of length l moves with speed v perpendicular to a uniform field B and to its own length. The emf across it is (a) Bv/l (b) Bvl (c) Bl/v (d) ½Bvl

4. Eddy current losses in a transformer core are reduced by (a) using a laminated core (b) using a thick solid iron core (c) raising the supply frequency (d) using a copper core

5. A rod of length l rotates about one end with angular speed ω in a plane perpendicular to B. The emf between its ends is (a) Bωl² (b) 2Bωl² (c) Bωl (d) ½Bωl²

6. A small magnet is dropped down a long vertical copper pipe. Its acceleration, after it enters the pipe, is (a) greater than g (b) equal to g (c) less than g (d) always exactly zero

7. Which of these does NOT depend on eddy currents? (a) Induction cooktop (b) Glowing of a bulb filament (c) Magnetic braking of a metro train (d) Dead-beat galvanometer

8. A 2 m rod moves at 5 m/s perpendicular to a 0.1 T field and to its length. The emf is (a) 1 V (b) 10 V (c) 0.1 V (d) 0.5 V

9. The N-pole of a magnet is pushed towards a coil. The face of the coil nearer the magnet becomes (a) an S-pole (b) neutral (c) an N-pole (d) alternately N and S

10. A straight rod moves parallel to a uniform magnetic field. The emf across it is (a) Bvl (b) maximum (c) Bvl/2 (d) zero

Level 2: NEET standard

11. A rod of length 0.4 m slides at 5 m/s on rails in a 0.5 T field perpendicular to the plane. The circuit resistance is 2 Ω. The current is (a) 0.25 A (b) 0.5 A (c) 1 A (d) 2 A

12. For the rod in Q11, the external force needed to keep its speed constant is (a) 0.1 N (b) 0.2 N (c) 0.05 N (d) 1 N

13. An aircraft of wingspan 40 m flies level at 900 km/h where the vertical component of the Earth's field is 5 × 10⁻⁵ T. The emf between the wing tips is (a) 5 V (b) 0.05 V (c) 0.5 V (d) 1 V

14. A rod 0.5 m long rotates about one end at 10 revolutions per second, in a plane perpendicular to a 0.2 T field. The emf between its ends is about (a) 3.14 V (b) 0.785 V (c) 6.28 V (d) 1.57 V

15. A metal disc of radius 0.2 m spins at 50 rad/s about its axis, which is along a 0.4 T field. The emf between centre and rim is (a) 0.4 V (b) 0.8 V (c) 0.2 V (d) 4 V

16. A semicircular wire of radius 5 cm moves at 4 m/s perpendicular to its diameter, in a 0.5 T field perpendicular to its plane. The emf between its ends is (a) 0.1 V (b) 0.314 V (c) 0.2 V (d) 0.4 V

17. A rod 1 m long moves in its own plane, perpendicular to a 0.5 T field, at 2 m/s. Its velocity makes 60° with the length of the rod. The emf is about (a) 0.5 V (b) 0.87 V (c) 1 V (d) zero

18. A rod of mass 10 g and length 0.2 m slides down smooth vertical rails joined by a 1 Ω resistor, in a 0.5 T horizontal field perpendicular to the rails. Its terminal velocity is (g = 10 m/s²) (a) 5 m/s (b) 2.5 m/s (c) 20 m/s (d) 10 m/s

19. A long straight wire in the plane of the page carries an increasing current upward. A rectangular loop lies in the page to the right of the wire. The induced current in the loop, as seen by the reader, is (a) clockwise (b) anticlockwise (c) zero (d) alternating

20. The N-pole of a magnet is moved the same way towards a copper ring and towards an identical wooden ring. Which is correct? (a) Emf is induced in both, current flows only in the copper ring (b) Emf and current in both (c) Emf only in the copper ring (d) Neither has an emf

21. A rod of length 0.5 m moves at 2 m/s on rails in a 1 T field. The circuit resistance is 0.5 Ω. The power dissipated is (a) 1 W (b) 4 W (c) 2 W (d) 0.5 W

22. A bar magnet, N-pole downward, falls towards a horizontal copper ring. Seen from above, the induced current in the ring while the magnet approaches is (a) clockwise (b) zero (c) clockwise, then anticlockwise (d) anticlockwise

Level 3: Challenge

23. A rod of mass 0.1 kg lies on smooth horizontal rails 0.5 m apart, joined by a 1 Ω resistor, in a 1 T vertical field. It is given a speed of 4 m/s and released. The distance it travels before stopping is (a) 0.8 m (b) 1.6 m (c) 3.2 m (d) it never stops

24. In Q23, the total heat produced in the resistor is (a) 0.4 J (b) 1.6 J (c) 0.8 J (d) 0.2 J

25. A metal rod of length l rotates about an axis through its midpoint, perpendicular to the rod and parallel to a uniform field B, with angular speed ω. The emf between its two ends is (a) zero (b) ½Bωl² (c) ⅛Bωl² (d) ¼Bωl²

26. A ceiling fan with 0.5 m blades turns at 360 rpm. The vertical component of the Earth's field is 4 × 10⁻⁵ T. The emf between the hub and a blade tip is about (a) 1.9 mV (b) 0.38 mV (c) 19 mV (d) 0.19 mV

27. A square loop of side 0.1 m and resistance 0.02 Ω enters a region of 0.4 T field (perpendicular to the loop) at a steady 0.5 m/s. The current while it is entering is (a) 0.5 A (b) 1 A (c) 2 A (d) 0.1 A

28. Two pendulums, one with a solid copper plate and one with a copper plate cut with many slots, swing between the poles of a strong magnet. Which is correct? (a) Both stop at the same time (b) The slotted plate stops first (c) The solid plate stops first (d) Neither is affected

29. Assertion (A): A magnet falls more slowly through a vertical copper pipe than through a PVC pipe of the same size. Reason (R): Eddy currents induced in the copper pipe oppose the motion of the magnet. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: The emf between the ends of a rod rotating about one end in a perpendicular field is Bωl². Statement II: Lenz's law follows from the law of conservation of energy. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1cAiding the change would create energy from nothing
2bStatement of Lenz's law
3be = Bvl
4aInsulated sheets break eddy current paths
5dIntegrate Bωr dr from 0 to l
6cEddy currents in the pipe oppose the fall
7bA filament glows by ordinary Joule heating of its own current
8a0.1 × 5 × 2 = 1 V
9cLike poles repel the approaching magnet
10dv parallel to B gives no force on charges
11be = 0.5 × 5 × 0.4 = 1 V; I = 0.5 A
12aF = BIl = 0.5 × 0.5 × 0.4
13c900 km/h = 250 m/s; 5 × 10⁻⁵ × 250 × 40
14dω = 20π; ½ × 0.2 × 20π × 0.25 = 1.57 V
15a½ × 0.4 × 50 × 0.04
16cEffective length 0.1 m; 0.5 × 4 × 0.1
17bEffective length l sin 60° = 0.866 m
18dmgR/(B²l²) = 0.1/0.01
19bInto-page flux rises, induced field out of page
20aEmf needs only flux change; current needs a conductor
21ce = 1 V; P = e²/R = 2 W
22dUpper face becomes N to repel; anticlockwise from above
23bx = mv0R/(B²l²) = 0.4/0.25
24cAll kinetic energy ½ × 0.1 × 16 becomes heat
25aBoth halves give equal emf from centre outward
26dω = 12π; ½ × 4 × 10⁻⁵ × 12π × 0.25 = 1.9 × 10⁻⁴ V
27bI = Bav/R = 0.02/0.02
28cSlots cut eddy current loops in the slotted plate
29aEddy current drag is the cause
30dCorrect emf is ½Bωl²; II is true

Chapter 2 revision sheet

One-page summary

  • Lenz's law: the induced current flows so as to oppose the change in flux that produces it.

  • Lenz's law is a result of energy conservation: if the induced current helped the change, energy would come from nowhere.

  • N-pole approaching a coil: the near face becomes N (repels). N-pole leaving: the near face becomes S (attracts back).

  • A magnet falling through a closed ring has a < g; through a ring with a cut, a = g (no current).

  • Motional emf of a rod moving perpendicular to B and to itself: e = Bvl.

  • For a rod at an angle, use only the components of v and l that are perpendicular to B and to each other (effective length).

  • Origin of motional emf: the magnetic force qvB pushes free charges along the rod.

  • Rod on rails with total resistance R: I = Bvl/R, retarding force F = B²l²v/R, power P = B²l²v²/R = I²R.

  • Constant pulling force F: rod reaches terminal speed v = FR/(B²l²). Falling rod on vertical rails: v = mgR/(B²l²).

  • Rod of length l rotating about one end with angular speed ω: e = ½Bωl². A disc of radius r gives ½Bωr² between centre and rim.

  • A rod rotating about its midpoint has zero emf between its two ends.

  • Eddy currents: induced loops of current in bulk metal; they heat the metal and oppose motion.

  • Reduce eddy currents with laminated cores or slotted plates. Uses: magnetic braking, induction furnace, dead-beat galvanometer, induction cooktop, electric power meters.

Must-remember table

Set-upemfOther results
Rod on rails, speed vBvlI = Bvl/R, F = B²l²v/R
Power to keep rod moving—P = B²l²v²/R
Constant force F on rod—v terminal = FR/(B²l²)
Rod falling on vertical rails—v terminal = mgR/(B²l²)
Rod rotating about one end½Bωl²Same for disc, centre to rim
Rod rotating about midpoint0 between endsEach half gives ½Bω(l/2)²
Aircraft wings, span lBv v lBv = vertical component of Earth's field

Memory aids

  • "Nature hates change": whatever the flux is doing, the induced current tries to undo it. More flux in? Push it out. Flux leaving? Pull it back.

  • "Near face copies the visitor": the coil face near an approaching pole takes the same pole and repels it; for a leaving pole it takes the opposite pole.

  • "BVL is a bus line": B, v, l must all be at right angles, like three roads meeting at a corner; if any two are parallel, emf is zero.

  • "Half Bowl": ½ B ω l² for anything spinning about one end (blade, spoke, disc).

  • "Slots stop swirls": cutting slots or laminating breaks up eddy current loops.

Concept connections

  • Force on a current-carrying rod (F = BIl) and the Lorentz force come from Physics Book 13: Magnetic Effects of Current and Magnetism.

  • Terminal velocity and energy balance use ideas from Physics Book 3: Laws of Motion and Physics Book 4: Work, Energy and Power.

  • Rotating rods and discs use angular speed from Physics Book 5: Rotational Motion.

Practice MCQs: Chapter 2, Level 4 (new NEET pattern)

31. A rod of length 0.4 m is in a uniform field B = 0.5 T, with the rod perpendicular to B. Match each motion (List I) with the emf between its ends (List II).

List I:

  • A. Moves at 5 m/s perpendicular to itself and to B

  • B. Rotates at 10 rad/s about one end, in a plane perpendicular to B

  • C. Rotates at 10 rad/s about its midpoint, in a plane perpendicular to B

  • D. Moves at 5 m/s perpendicular to B, at 30° to its own length

List II:

  • (i) 0

  • (ii) 0.4 V

  • (iii) 1.0 V

  • (iv) 0.5 V

(a) A-ii, B-iii, C-i, D-iv (b) A-iii, B-iv, C-i, D-ii (c) A-iv, B-ii, C-i, D-iii (d) A-iii, B-ii, C-i, D-iv

32. Match the device (List I) with the physics behind it (List II).

List I:

  • A. Induction furnace

  • B. Magnetic braking in trains

  • C. Dead-beat galvanometer

  • D. Laminated transformer core

List II:

  • (i) Eddy current force opposes motion of metal

  • (ii) Eddy currents are kept small

  • (iii) Heat from eddy currents melts metal

  • (iv) Eddy currents in a metal frame damp the swings of the coil

(a) A-i, B-iii, C-iv, D-ii (b) A-iii, B-i, C-iv, D-ii (c) A-iii, B-iv, C-i, D-ii (d) A-ii, B-i, C-iv, D-iii

33. A rod of length l slides at constant speed v on rails in a field B; the total resistance is R. Match List I with List II.

List I:

  • A. Induced emf

  • B. Induced current

  • C. Magnetic force on the rod

  • D. Power needed to keep it moving

List II:

  • (i) B²l²v/R

  • (ii) Bvl

  • (iii) B²l²v²/R

  • (iv) Bvl/R

(a) A-ii, B-i, C-iv, D-iii (b) A-iv, B-ii, C-i, D-iii (c) A-ii, B-iv, C-i, D-iii (d) A-ii, B-iv, C-iii, D-i

34. A bar magnet is dropped N-pole first through a horizontal copper ring. Match the stage (List I) with what happens (List II).

List I:

  • A. Magnet approaching the ring from above

  • B. Magnet's centre exactly at the ring

  • C. Magnet leaving the ring below

  • D. Ring has a narrow cut in it

List II:

  • (i) Ring attracts the magnet back, a < g

  • (ii) Ring repels the magnet, a < g

  • (iii) No induced current at any stage

  • (iv) Induced current is zero for an instant

(a) A-ii, B-iv, C-i, D-iii (b) A-i, B-iv, C-ii, D-iii (c) A-ii, B-iii, C-i, D-iv (d) A-iv, B-ii, C-i, D-iii

35. How many of the following statements are correct?

  • A. Lenz's law follows from conservation of energy.

  • B. The induced current always opposes the magnetic field of the magnet.

  • C. Laminating a core reduces eddy currents.

  • D. Motional emf arises from the magnetic force on free charges in the moving rod.

  • E. A rod moving along its own length in a field has an emf Bvl.

(a) 3 (b) 4 (c) 2 (d) 5

36. A rod on smooth horizontal rails is pulled by a constant force F in a vertical field B; the circuit resistance is R. Choose the correct set.

  • A. The rod reaches a terminal speed FR/(B²l²).

  • B. At terminal speed, the power F v equals I²R.

  • C. The acceleration of the rod stays constant.

  • D. The current grows and then becomes constant.

(a) A and C only (b) A, B and D only (c) B and C only (d) A, B, C and D

37. A rod of length l rotates about one end in a plane perpendicular to a uniform field B. How many statements are correct?

  • A. The emf between the ends is ½Bωl².

  • B. The midpoint of the rod is at the highest potential.

  • C. Doubling the length makes the emf four times.

  • D. If it rotates about its midpoint instead, the emf between its two ends is zero.

  • E. The emf between the pivot and the midpoint is one-fourth of the emf between the pivot and the free end.

(a) 2 (b) 3 (c) 5 (d) 4

38. An aircraft flies horizontally. The emf between its wing tips depends on:

  • A. The vertical component of Earth's field

  • B. The horizontal component of Earth's field

  • C. The wingspan

  • D. The speed of the aircraft

(a) B, C and D only (b) A and C only (c) A, C and D only (d) A, B, C and D

39. A square loop of side 0.1 m and resistance 0.5 Ω moves at a constant 2 m/s into, through and out of a field region of width 0.3 m (B = 0.5 T, normal to the loop). Take t = 0 as the moment the front edge enters. Which emf–time description is correct? (a) 0.1 V throughout 0 to 0.2 s (b) +0.1 V for 0–0.05 s, zero for 0.05–0.15 s, −0.1 V for 0.15–0.20 s (c) +0.1 V for 0–0.1 s, −0.1 V for 0.1–0.2 s (d) zero for 0–0.05 s, +0.1 V for 0.05–0.15 s, zero after

40. A rod of mass 0.02 kg and length 0.5 m slides down smooth vertical rails in a horizontal field B; the circuit resistance is 0.2 Ω (g = 10 m/s²). Its speed is recorded:

t (s)00.20.40.81.62.4
v (m/s)01.62.53.53.94.0

The field B is: (a) 0.1 T (b) 0.4 T (c) 0.2 T (d) 0.02 T

41. For a rod moving on rails at speed v, the graphs of magnetic retarding force against v and of power dissipated against v are: (a) a straight line through the origin; a parabola through the origin (b) a parabola; a straight line (c) both straight lines through the origin (d) a hyperbola; a straight line

Case for Q42–43: A ceiling fan has three metal blades, each 0.6 m long from hub to tip. It turns at 300 rpm in a horizontal plane. The vertical component of Earth's field there is 4 × 10⁻⁵ T.

42. The emf between the hub and the tip of one blade is about: (a) 0.11 mV (b) 0.45 mV (c) 2.3 mV (d) 0.23 mV

43. The emf between the tips of two different blades is: (a) 0 (b) 0.23 mV (c) 0.45 mV (d) 0.68 mV

44. A rod of length 1 m moves at 4 m/s on rails in a field of 0.5 T; the circuit resistance is 2 Ω. The power needed to keep it moving is P1. If the speed is doubled and the resistance is also doubled, the power is P2. Then P1 and P2 are: (a) 2 W, 8 W (b) 4 W, 8 W (c) 2 W, 4 W (d) 1 W, 2 W

45. A copper disc of radius 0.2 m spins at 50 rev/s about its axis, which is parallel to a uniform 0.1 T field. A 2 Ω resistor is connected between the axle and the rim (neglect the disc's own resistance). The current is about: (a) 0.157 A (b) 0.314 A (c) 0.628 A (d) 3.14 A

Level 4 answer key

QAnsReason
31dBvl = 1.0 V; ½Bωl² = 0.4 V; about midpoint 0; 1.0 × sin 30° = 0.5 V
32bFurnace heats, brake opposes motion, galvanometer is damped, lamination reduces eddy currents
33ce = Bvl, I = e/R, F = BIl, P = Fv
34aApproach: repel; at centre flux is maximum so rate is zero; leaving: attract; cut ring: no current
35aA, C, D true; current opposes the change, not the field; v along l gives no emf
36bAcceleration falls as current grows, so C is false
37dA, C, D, E true; potential changes steadily from pivot to tip, so B is false
38cOnly the vertical component is cut by horizontal wings moving horizontally
39bEntry 0.05 s with emf 0.5 × 2 × 0.1 = 0.1 V; fully inside 0.1 s with no change; exit reverses sign
40cv terminal = mgR/(B²l²) = 4, so B² = 0.04/(0.25 × 4) = 0.04, B = 0.2 T
41aF = B²l²v/R is linear in v; P = B²l²v²/R is quadratic
42dω = 10π rad/s; ½ × 4 × 10⁻⁵ × 31.4 × 0.36 = 2.3 × 10⁻⁴ V
43aAll tips are at the same potential relative to the hub
44ce = 2 V, P1 = e²/R = 2 W; P ∝ v²/R gives 4/2 = 2 times, so 4 W
45be = ½ × 0.1 × 100π × 0.04 = 0.628 V; I = 0.628/2 = 0.314 A
28 min left
‹
›