Chapter 7 of 12 · 21 min read

Chapter 5: AC Through R, L and C

What you will learn

  • How current and voltage behave in a pure resistor, a pure inductor and a pure capacitor on AC.

  • Inductive reactance XL = ωL and capacitive reactance XC = 1/ωC, derived step by step.

  • The phase relations: in phase for R, current lagging by 90° for L, current leading by 90° for C.

  • How reactance changes with frequency, and why a capacitor blocks DC while an inductor passes it.

  • How to write the current equation for each element from a given voltage.

In this chapter each element is "pure": the resistor has no inductance, the coil has no resistance, and the capacitor has no leakage. The source is v = V0 sin ωt throughout.

5.1 AC through a pure resistor

Kirchhoff's loop rule at any instant gives v = iR. So:

i=V0Rsin⁡ωt=I0sin⁡ωt,I0=V0Ri = \frac{V_0}{R}\sin\omega t = I_0\sin\omega t, \qquad I_0 = \frac{V_0}{R}

Current and voltage rise and fall together. They are in phase. Ohm's law holds for peak values and for rms values: Irms = Vrms/R. The resistance does not depend on frequency.

The instantaneous power is vi = V0I0 sin² ωt. Its average over a cycle is V0I0/2 = VrmsIrms. A resistor always takes power from the source and turns it into heat.

5.2 AC through a pure inductor

Now connect a coil of inductance L and no resistance. The source emf must balance the back emf of the coil at every instant:

V0sin⁡ωt=LdidtV_0\sin\omega t = L\frac{di}{dt}

Integrate both sides with respect to time:

i=−V0ωLcos⁡ωt=V0ωLsin⁡(ωt−π2)i = -\frac{V_0}{\omega L}\cos\omega t = \frac{V_0}{\omega L}\sin\left(\omega t - \frac{\pi}{2}\right)

(The constant of integration is zero, since there is no steady DC part.) So the peak current is I0 = V0/(ωL), and:

  • The current lags the voltage by π/2 (90°), a quarter cycle.

  • The opposition ωL plays the role of resistance. It is called the inductive reactance.

XL=ωL=2πfLX_L = \omega L = 2\pi f L

XL is measured in ohm. It grows in proportion to frequency. For DC (f = 0), XL = 0: a pure coil is a plain wire for steady current. At high frequency the coil strongly opposes current. That is why coils are used as "chokes" to block high-frequency signals.

Why the lag? The back emf depends on how fast the current changes. The current changes fastest when it passes through zero. So the voltage is at its peak when the current is zero, and the current reaches its peak a quarter cycle later.

Power: vi = V0I0 sin ωt × (−cos ωt) = −½V0I0 sin 2ωt. Its average over a cycle is zero. The coil stores energy in its field for a quarter cycle and returns it in the next.

5.3 AC through a pure capacitor

Connect a capacitor C across the source. At every instant the charge is q = Cv = CV0 sin ωt. The current is the rate of flow of charge:

i=dqdt=ωCV0cos⁡ωt=V01/ωCsin⁡(ωt+π2)i = \frac{dq}{dt} = \omega C V_0\cos\omega t = \frac{V_0}{1/\omega C}\sin\left(\omega t + \frac{\pi}{2}\right)

So I0 = V0/(1/ωC), and:

  • The current leads the voltage by π/2 (90°).

  • The opposition 1/ωC is the capacitive reactance.

XC=1ωC=12πfCX_C = \frac{1}{\omega C} = \frac{1}{2\pi f C}

XC falls as frequency rises. For DC (f = 0), XC is infinite: once charged, a capacitor allows no steady current. At high frequency it acts almost like a short circuit.

Why the lead? Current into a capacitor is largest when its voltage is changing fastest, which is when the voltage is passing through zero. So the current peaks a quarter cycle before the voltage does.

No charge actually crosses the gap between the plates. The plates charge one way, discharge, then charge the other way. The current flows in the connecting wires, back and forth. The average power is again zero.

5.4 The three elements side by side

Figure 5.1 · Phasor diagrams for pure R, pure L and pure C
Figure 5.1 · Phasor diagrams for pure R, pure L and pure C

With V drawn along the reference line and rotation anticlockwise, the current phasor sits on V for R, a quarter turn behind for L, and a quarter turn ahead for C.

PropertyPure RPure LPure C
OppositionRXL = ωLXC = 1/ωC
Depends on f?NoRises in proportion to fFalls as 1/f
Graph against fHorizontal lineStraight line through originRectangular hyperbola
Phase of current vs voltageIn phaseLags by 90°Leads by 90°
Behaviour with DCSame RShort (zero opposition)Open (blocks)
Average powerVrmsIrmsZeroZero

A memory aid: in ELI, the voltage E comes before the current I in a coil L. In ICE, the current I comes before E in a capacitor C.

Two results follow from the formulas:

  • The product XL × XC = (ωL)(1/ωC) = L/C. It does not depend on frequency.

  • In both L and C, current and voltage are 90° apart. So (v/V0)² + (i/I0)² = 1 at every instant. When one is at its peak, the other is zero.

Worked example 5.1: A 100 Ω resistor is connected to 220 V, 50 Hz mains. Find the rms and peak currents.

Solution: Irms = 220/100 = 2.2 A. I0 = 2.2 × √2 = 3.11 A.

Worked example 5.2: A 0.5 H coil of negligible resistance is connected to 220 V, 50 Hz mains. Find XL and the rms current.

Solution: XL = 2π × 50 × 0.5 = 157 Ω. Irms = 220/157 = 1.40 A.

Worked example 5.3: A 20 μF capacitor is connected to 220 V, 50 Hz mains. Find XC and the rms current.

Solution: XC = 1/(2π × 50 × 20 × 10⁻⁶) = 159 Ω. Irms = 220/159 = 1.38 A.

Worked example 5.4: At what frequency does a 0.2 H inductor have a reactance of 100 Ω?

Solution: f = XL/(2πL) = 100/(2π × 0.2) = 79.6 Hz.

Worked example 5.5: The supply frequency is doubled at the same voltage. What happens to the current through (i) a pure inductor (ii) a pure capacitor?

Solution: (i) XL doubles, so the current halves. (ii) XC halves, so the current doubles.

Worked example 5.6: A voltage v = 200 sin(100πt) V is applied across a pure inductor of (1/π) H. Write the current.

Solution: XL = 100π × (1/π) = 100 Ω. I0 = 200/100 = 2 A. The current lags by π/2: i = 2 sin(100πt − π/2) A = −2 cos(100πt) A.

Worked example 5.7: A voltage v = 100 sin(1000t) V is applied across a 10 μF capacitor. Write the current. What is the current when the voltage is at its peak?

Solution: XC = 1/(1000 × 10⁻⁵) = 100 Ω. I0 = 1 A. i = sin(1000t + π/2) = cos(1000t) A. When v is at its peak, sin(1000t) = 1, so cos(1000t) = 0. The current is zero.

Worked example 5.8 (NEET-hard): A pure coil draws 2 A (rms) from 220 V, 50 Hz mains. Find L. What current does it draw from a 220 V, 60 Hz supply?

Solution: XL = 220/2 = 110 Ω, so L = 110/(2π × 50) = 0.35 H. At 60 Hz, XL = 110 × 60/50 = 132 Ω. Irms = 220/132 = 1.67 A.

Quick revision

  • R: in phase; I = V/R; no frequency dependence.

  • L: XL = ωL = 2πfL; current lags by 90°; zero opposition to DC.

  • C: XC = 1/ωC = 1/(2πfC); current leads by 90°; blocks DC.

  • Average power is zero in pure L and pure C.

  • XL × XC = L/C, independent of f.

  • For L or C: (v/V0)² + (i/I0)² = 1.

  • ELI the ICE man: voltage leads in L, current leads in C.

NEET traps

  • Swapping lead and lag between L and C.

  • Using f instead of ω = 2πf in XL or XC.

  • Saying a capacitor conducts DC at f = 0. XC is infinite.

  • Forgetting to convert μF to F (1 μF = 10⁻⁶ F) or mH to H.

  • Applying I0 = V0/X and then mixing peak with rms in the same step.

  • Thinking pure L or C wastes power. They store and return it.

Practice MCQs: Chapter 5

Level 1: Concept check

1. In a purely resistive AC circuit, the phase difference between voltage and current is (a) π/2 (b) zero (c) π (d) π/4

2. In a purely inductive AC circuit, the current (a) leads the voltage by π/2 (b) is in phase with the voltage (c) lags the voltage by π/2 (d) lags the voltage by π

3. The capacitive reactance of a capacitor C at angular frequency ω is (a) 1/ωC (b) ωC (c) ωL (d) 1/ωL

4. The inductive reactance of a pure coil for a steady DC is (a) infinite (b) equal to its resistance (c) equal to L (d) zero

5. A capacitor blocks steady DC because, at zero frequency, its reactance is (a) zero (b) infinite (c) equal to 1 Ω (d) equal to C

6. A graph of inductive reactance against frequency is (a) a rectangular hyperbola (b) a parabola (c) a straight line through the origin (d) a horizontal line

7. The SI unit of reactance is (a) ohm (b) henry (c) farad (d) siemens

8. In a purely capacitive AC circuit, the current (a) lags the voltage by π/2 (b) is in phase with the voltage (c) leads the voltage by π (d) leads the voltage by π/2

9. A graph of capacitive reactance against frequency is (a) a straight line through the origin (b) a rectangular hyperbola (c) a parabola (d) a horizontal line

10. The average power taken by a pure inductor from an AC source over one cycle is (a) VrmsIrms (b) V0I0/2 (c) zero (d) V0I0

Level 2: NEET standard

11. The reactance of a 0.2 H inductor at 50 Hz is about (a) 62.8 Ω (b) 31.4 Ω (c) 10 Ω (d) 6.28 Ω

12. The reactance of a 10 μF capacitor at 50 Hz is about (a) 31.8 Ω (b) 3180 Ω (c) 159 Ω (d) 318 Ω

13. A pure inductor of (1/π) H is connected to 220 V, 50 Hz mains. The rms current is (a) 1.1 A (b) 2.2 A (c) 3.11 A (d) 22 A

14. The supply frequency across a capacitor is doubled, keeping the voltage the same. The current (a) halves (b) stays the same (c) doubles (d) becomes four times

15. A capacitor of (100/π) μF is connected to 220 V, 50 Hz mains. The peak current is about (a) 3.11 A (b) 2.2 A (c) 1.56 A (d) 4.4 A

16. A voltage v = 100 sin(500t) V is applied across a pure 0.4 H coil. The current, in ampere, is (a) 0.5 sin(500t) (b) 0.5 sin(500t + π/2) (c) 250 sin(500t − π/2) (d) 0.5 sin(500t − π/2)

17. A 0.1 H inductor has a reactance of 314 Ω at a frequency of about (a) 50 Hz (b) 500 Hz (c) 5000 Hz (d) 1000 Hz

18. A 1 μF capacitor has a reactance of 1 kΩ at a frequency of about (a) 1000 Hz (b) 15.9 Hz (c) 159 Hz (d) 1590 Hz

19. A pure coil draws 2 A from a 50 Hz source. The same rms voltage at 100 Hz makes it draw (a) 1 A (b) 4 A (c) 2 A (d) 0.5 A

20. A capacitor draws 1 A from a 50 Hz source. The same rms voltage at 200 Hz makes it draw (a) 0.25 A (b) 2 A (c) 1 A (d) 4 A

21. Which element lets steady DC pass easily but strongly opposes high-frequency AC? (a) A capacitor (b) An inductor (c) Both (d) Neither

22. In a pure inductor on AC, at the instant the current is at its maximum, the voltage across it is (a) maximum (b) half the maximum (c) zero (d) 1/√2 of the maximum

Level 3: Challenge

23. An inductor and a capacitor have equal reactances at 1 kHz. At 2 kHz, the ratio XL : XC is (a) 4 : 1 (b) 2 : 1 (c) 1 : 4 (d) 1 : 1

24. For L = 0.1 H and C = 10 μF, the product XL × XC at 50 Hz is (a) 10² Ω² (b) 10⁶ Ω² (c) depends on π (d) 10⁴ Ω²

25. A pure capacitor is connected to v = V0 sin ωt. When the instantaneous voltage is V0/2, the magnitude of the current is (I0 = peak current) (a) I0/2 (b) (√3/2)I0 (c) I0 (d) I0/√2

26. A pure inductor draws 2 A (rms) from 220 V, 50 Hz mains. Its inductance is about (a) 0.7 H (b) 0.175 H (c) 0.35 H (d) 1.1 H

27. A capacitor draws 0.69 A (rms) from 220 V, 50 Hz mains. Its capacitance is about (a) 10 μF (b) 1 μF (c) 20 μF (d) 100 μF

28. The rms current through a circuit element, at a fixed rms voltage, rises in proportion to the frequency. The element is (a) a resistor (b) a capacitor (c) an inductor (d) a diode

29. Assertion (A): A capacitor lets AC through but blocks steady DC. Reason (R): Capacitive reactance is inversely proportional to frequency. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: The reactance of an inductor does not depend on the frequency of the supply. Statement II: The average power taken by a pure capacitor over a complete cycle is zero. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1bv = iR at every instant
2ci = −(V0/ωL) cos ωt
3aXC = 1/ωC
4dXL = ωL = 0 when ω = 0
5b1/ωC becomes infinite at ω = 0
6cXL = 2πfL is linear in f
7aReactance is V/I, in ohm
8di = ωCV0 cos ωt
9bXC × f is constant
10cAverage of sin 2ωt is zero
11a2π × 50 × 0.2 = 62.8 Ω
12d1/(2π × 50 × 10⁻⁵) = 318 Ω
13bXL = 100 Ω; 220/100
14cXC halves
15aXC = 100 Ω; I0 = 311/100
16dXL = 200 Ω, I0 = 0.5 A, current lags
17bf = 314/(2π × 0.1) ≈ 500 Hz
18cf = 1/(2π × 10⁻⁶ × 10³)
19aXL doubles
20dXC becomes one-fourth
21bXL is small at low f, large at high f
22cv and i are 90° apart
23aXL doubles, XC halves
24dXL × XC = L/C = 0.1/10⁻⁵
25b(v/V0)² + (i/I0)² = 1
26cXL = 110 Ω; L = 110/(100π)
27aC = I/(ωV) = 0.69/(314 × 220)
28bI = ωCV rises with f
29aInfinite XC at f = 0 explains blocking DC
30dXL = ωL depends on f; II is true

Chapter 5 revision sheet

One-page summary

  • Pure R: i = (V0/R) sin ωt. Current and voltage are in phase. Average power = Vrms Irms.

  • Pure L: i = (V0/ωL) sin(ωt − π/2). Current lags voltage by 90° (a quarter period, T/4).

  • Inductive reactance XL = ωL = 2πfL, in ohm. XL rises in proportion to f and is zero for DC.

  • Pure C: i = ωCV0 sin(ωt + π/2). Current leads voltage by 90°.

  • Capacitive reactance XC = 1/(ωC) = 1/(2πfC), in ohm. XC falls as f rises and is infinite for DC.

  • A capacitor blocks steady DC but passes AC; an inductor passes DC freely but opposes high-frequency AC.

  • In pure L or pure C, average power over a cycle is zero: energy taken in one quarter cycle is returned in the next.

  • Instantaneous power in pure L or C oscillates at 2ω with zero mean.

  • In pure C, current is maximum when voltage is zero (and the capacitor is uncharged).

  • In pure L, current is maximum when voltage is zero; the magnetic energy is then maximum, ½LI0².

  • Ohm's-law forms: Irms = Vrms/XL or Vrms/XC.

  • Graphs: XL against f is a straight line through the origin; XC against f is a rectangular hyperbola; R against f is a horizontal line.

  • A real coil has both R and L: on DC only R limits current; on AC the combination Z = √(R² + XL²) does.

Must-remember table

ElementOppositionPhase of i relative to vAverage power
Pure RRIn phaseVrms Irms
Pure LXL = ωLLags by 90°0
Pure CXC = 1/ωCLeads by 90°0
L on DCXL = 0—acts as a plain wire
C on DCXC infinite—no steady current

Memory aids

  • "ELI the ICE man": in an inductor (L), voltage E comes before current I; in a capacitor (C), current I comes before voltage E.

  • "L loves low, C craves high": an inductor passes low frequencies, a capacitor passes high frequencies.

  • "XL climbs, XC slides": XL goes up with f, XC goes down with f.

  • "Pure L and C pay no bill": they draw no average power from the supply.

Concept connections

  • Capacitor charge q = CV and energy ½CV² come from Physics Book 11: Electrostatics.

  • Self inductance and back emf come from Chapter 3 of this book.

  • Frequency-dependent filtering with L and C is used in rectifier circuits of Physics Book 19: Electronic Devices.

Practice MCQs: Chapter 5, Level 4 (new NEET pattern)

31. Match the element (List I) with its behaviour (List II).

List I:

  • A. Pure resistor on AC

  • B. Pure inductor on AC

  • C. Pure capacitor on AC

  • D. Ideal capacitor on steady DC

List II:

  • (i) Current leads voltage by 90°

  • (ii) Current in phase with voltage

  • (iii) No steady current flows

  • (iv) Current lags voltage by 90°

(a) A-ii, B-iv, C-i, D-iii (b) A-ii, B-i, C-iv, D-iii (c) A-iii, B-iv, C-i, D-ii (d) A-ii, B-iv, C-iii, D-i

32. Match each reactance (List I) with its value (List II).

List I:

  • A. XL of 0.1 H at 50 Hz

  • B. XC of 20 μF at 50 Hz

  • C. XL of 0.1 H at 100 Hz

  • D. XC of 20 μF at 100 Hz

List II:

  • (i) 31.4 Ω

  • (ii) 62.8 Ω

  • (iii) 79.6 Ω

  • (iv) 159 Ω

(a) A-ii, B-iv, C-i, D-iii (b) A-i, B-iii, C-ii, D-iv (c) A-i, B-iv, C-ii, D-iii (d) A-iv, B-i, C-iii, D-ii

33. Match the graph (List I) with its shape (List II).

List I:

  • A. XL against f

  • B. XC against f

  • C. R against f

  • D. Instantaneous power against time for a pure inductor

List II:

  • (i) Rectangular hyperbola

  • (ii) Sinusoid at twice the source frequency with zero mean

  • (iii) Straight line through the origin

  • (iv) Line parallel to the f-axis

(a) A-i, B-iii, C-iv, D-ii (b) A-iii, B-i, C-iv, D-ii (c) A-iii, B-iv, C-i, D-ii (d) A-iii, B-i, C-ii, D-iv

34. Match the situation (List I) with the result (List II).

List I:

  • A. Inductor carrying steady DC

  • B. Capacitor connected to steady DC (after charging)

  • C. Inductor, supply frequency doubled

  • D. Capacitor, supply frequency doubled

List II:

  • (i) Zero reactance

  • (ii) Reactance halves

  • (iii) Infinite reactance

  • (iv) Reactance doubles

(a) A-iii, B-i, C-iv, D-ii (b) A-i, B-iii, C-ii, D-iv (c) A-i, B-iv, C-iii, D-ii (d) A-i, B-iii, C-iv, D-ii

35. How many of the following statements are correct?

  • A. In a pure inductor, the average power over a cycle is zero.

  • B. XC = ωC.

  • C. A capacitor blocks DC and passes AC.

  • D. In a pure resistor, Ohm's law holds for instantaneous values.

  • E. The unit of reactance is henry.

(a) 2 (b) 3 (c) 4 (d) 1

36. A pure capacitor C is connected to v = V0 sin ωt. Choose the correct set.

  • A. i = ωCV0 cos ωt.

  • B. The current is maximum when the voltage is zero.

  • C. The current is maximum when the voltage is maximum.

  • D. The rms current doubles if the frequency doubles at the same voltage.

(a) A and C only (b) B and C only (c) A, B and D only (d) A, B, C and D

37. How many of the following statements about an inductor on AC are correct?

  • A. In a pure inductor, the current peak comes T/4 after the voltage peak.

  • B. XL is zero for DC.

  • C. A coil with resistance dissipates some average power.

  • D. The instantaneous power in a pure inductor is always zero.

(a) 4 (b) 2 (c) 1 (d) 3

38. Choose the correct set of statements.

  • A. For a capacitor, XC is inversely proportional to f.

  • B. The resistance of an ideal resistor changes with frequency.

  • C. A choke is mainly an inductor.

  • D. A capacitor that draws AC from 220 V mains draws no steady current from a 220 V battery.

(a) A, C and D only (b) A and B only (c) B, C and D only (d) C and D only

39. A graph of XC against f for a capacitor passes through (100 Hz, 80 Ω). The reactance at 400 Hz and the capacitance are: (a) 320 Ω, 20 μF (b) 20 Ω, 20 μF (c) 20 Ω, 2 μF (d) 40 Ω, 20 μF

40. A single unknown element is connected to a 10 V rms source of variable frequency.

f (Hz)100200400
Irms (mA)502512.5

The element and its value are: (a) capacitor, 8 μF (b) resistor, 200 Ω (c) inductor, 3.2 H (d) inductor, 0.32 H

41. On a graph of v and i against time for one element, the current reaches its positive peak a quarter period after the voltage does. The element is: (a) a resistor (b) a capacitor (c) an inductor (d) cannot be decided

Case for Q42–43: A 50 μF capacitor is used across 220 V, 50 Hz mains in a fan regulator test. Its leakage is negligible.

42. The rms current is about: (a) 3.46 A (b) 4.89 A (c) 2.44 A (d) 0.35 A

43. If the same capacitor is used on a 220 V, 100 Hz supply, the rms current becomes about: (a) 1.73 A (b) 3.46 A (c) 6.91 A (d) 13.8 A

44. A pure 0.2 H inductor is connected to v = 200 sin(100t) volt. The maximum energy stored in it is: (a) 5 J (b) 10 J (c) 20 J (d) 2 J

45. A coil draws 4 A from a 12 V battery and 2.4 A from a 12 V rms, 50 Hz supply. Its inductance is about: (a) 12.7 mH (b) 4 mH (c) 25.5 mH (d) 1.27 mH

Level 4 answer key

QAnsReason
31aR in phase, L lags, C leads, C blocks steady DC
32c2π × 50 × 0.1 = 31.4; 1/(2π × 50 × 20 μF) = 159; doubled f doubles XL to 62.8 and halves XC to 79.6
33bXL ∝ f, XC ∝ 1/f, R constant, p = −½V0I0 sin 2ωt
34dXL = 0 and XC infinite for DC; XL ∝ f, XC ∝ 1/f
35bA, C, D true; XC = 1/ωC; reactance is in ohm
36ci = C dv/dt = ωCV0 cos ωt; it is maximum when v = 0
37dA, B, C true; instantaneous power swings, only its average is zero
38aAn ideal resistor does not depend on frequency
39bXC ∝ 1/f gives 80/4 = 20 Ω; C = 1/(2π × 100 × 80) = 19.9 μF
40dI ∝ 1/f means XL ∝ f; XL = 10/0.05 = 200 Ω at 100 Hz, L = 200/(200π) = 0.32 H
41cCurrent lagging by T/4 means an inductor
42aXC = 1/(2π × 50 × 50 μF) = 63.7 Ω; 220/63.7 = 3.46 A
43cDoubling f halves XC, so current doubles to 6.91 A
44bXL = 100 × 0.2 = 20 Ω, I0 = 10 A, U = ½ × 0.2 × 100 = 10 J
45aR = 3 Ω, Z = 5 Ω, XL = 4 Ω, L = 4/(100π) = 12.7 mH
21 min left
‹
›