Chapter 6 of 12 · 21 min read

Chapter 4: Alternating Current Basics

What you will learn

  • What an alternating current is, and how to read i = I0 sin(ωt + φ).

  • Peak, average and rms values, with full derivations.

  • Why AC meters show rms values, and why mains "220 V" peaks at about 311 V.

  • Average and rms values of a few non-sine waveforms that NEET likes.

  • Phasors: rotating arrows that turn sine functions into simple geometry.

4.1 What is an alternating current?

A battery pushes charge one way only. That is direct current (DC). The supply in your home pushes charge back and forth, reversing direction many times a second. That is alternating current (AC).

The simplest AC varies as a sine function of time:

v=V0sin⁡ωt,i=I0sin⁡(ωt+ϕ)v = V_0\sin\omega t, \qquad i = I_0\sin(\omega t + \phi)
  • V0 and I0 are the peak values (amplitudes).

  • ω is the angular frequency in rad/s. Frequency f = ω/2π, time period T = 1/f.

  • φ is the phase constant. It tells where the wave starts.

Indian mains is quoted as 220 V (often 230 V), 50 Hz. So ω = 2π × 50 = 100π ≈ 314 rad/s and T = 20 ms. In one second the current reverses direction 100 times, since it passes through zero twice each cycle.

Why we use AC. AC voltage can be raised or lowered easily with a transformer (Chapter 8). Power is sent over long lines at very high voltage and low current, which cuts I²R loss. Then it is stepped down for homes. DC cannot be transformed so simply.

4.2 Average value

Over one full cycle, a sine current is positive for half the time and negative for the other half, by equal amounts. So its average over a full cycle is zero. That is why a DC ammeter (moving coil) shows zero for AC.

Over a half cycle, the average is not zero. Take i = I0 sin ωt from t = 0 to T/2:

Iavg=1T/2∫0T/2I0sin⁡ωt dt=2I0T[−cos⁡ωtω]0T/2=2I0π≈0.637 I0I_{avg} = \frac{1}{T/2}\int_0^{T/2} I_0\sin\omega t\,dt = \frac{2I_0}{T}\left[\frac{-\cos\omega t}{\omega}\right]_0^{T/2} = \frac{2I_0}{\pi} \approx 0.637\,I_0

(Use ωT = 2π, so cos(ωT/2) = cos π = −1.)

4.3 Root mean square (rms) value

A heater does not care which way the current flows. The heat depends on i², which is always positive. So we ask: what steady DC would give the same heat in the same resistor in the same time? That DC value is the rms value.

Heat in time dt is i²R dt. Average of i² over one cycle:

⟨i2⟩=1T∫0TI02sin⁡2ωt dt=I02T∫0T1−cos⁡2ωt2 dt=I022\langle i^2\rangle = \frac{1}{T}\int_0^T I_0^2\sin^2\omega t\,dt = \frac{I_0^2}{T}\int_0^T \frac{1-\cos 2\omega t}{2}\,dt = \frac{I_0^2}{2}

The cos 2ωt term averages to zero over a full cycle. Taking the square root:

Irms=⟨i2⟩=I02≈0.707 I0,Vrms=V02I_{rms} = \sqrt{\langle i^2\rangle} = \frac{I_0}{\sqrt{2}} \approx 0.707\,I_0, \qquad V_{rms} = \frac{V_0}{\sqrt{2}}

The name says the steps in reverse: square the current, take the mean, then the root.

AC ammeters and voltmeters (hot-wire or moving-iron types, and digital meters set to AC) are calibrated to read rms values. When we say mains is 220 V, we mean Vrms = 220 V. The peak is 220 × √2 ≈ 311 V, and the voltage swings from +311 V to −311 V. The peak-to-peak value is about 622 V. Insulation and capacitors on mains must be rated for the peak, not the rms.

The ratio rms/average (half cycle) is called the form factor. For a sine wave it is (I0/√2) ÷ (2I0/π) = π/(2√2) ≈ 1.11.

4.4 Other waveforms

The factors 0.707 and 0.637 belong to sine waves only. For other shapes, go back to the definitions: rms = √(mean of i²) and average = mean of i.

Waveform (peak I0)Average over full cycleAverage over positive halfRMS value
Sine02I0/πI0/√2
Square, switching between +I0 and −I00I0I0
Half-wave rectified sineI0/π2I0/πI0/2
Full-wave rectified sine2I0/π2I0/πI0/√2
Sawtooth, rising 0 to I0 and droppingI0/2I0/2I0/√3

For a DC part plus a sine part, i = A + B sin ωt, the cross term averages to zero. So the mean of i² is A² + B²/2, and Irms = √(A² + B²/2).

4.5 Phasors

Adding sine functions with different phases by trigonometry is slow. Phasors make it quick.

A phasor is an arrow of length equal to the peak value, rotating anticlockwise about the origin with angular speed ω. Its projection on the vertical axis at any time is the instantaneous value. An arrow of length V0 making angle ωt with the horizontal axis has vertical projection V0 sin ωt. That is exactly v.

  • Two quantities with the same ω keep a fixed angle between their phasors. That angle is their phase difference.

  • The arrow ahead (further anticlockwise) leads. The one behind lags.

  • To add two sine quantities of the same frequency, add their phasors as vectors. The resultant's length is the peak of the sum.

Example: v1 = 3 sin ωt and v2 = 4 cos ωt = 4 sin(ωt + π/2). The phasors are at right angles. The sum has peak √(3² + 4²) = 5. We will use this idea for every circuit in Chapters 5 and 6.

Worked example 4.1: Indian mains is 220 V rms. Find the peak and peak-to-peak voltage.

Solution: V0 = √2 × 220 ≈ 311 V. Peak-to-peak = 2V0 ≈ 622 V.

Worked example 4.2: A current is i = 10 sin(100πt) A. Find the peak, rms value, frequency and period.

Solution: I0 = 10 A. Irms = 10/√2 = 7.07 A. ω = 100π, so f = 50 Hz and T = 0.02 s.

Worked example 4.3: For the current in 4.2, find the average over a half cycle.

Solution: Iavg = 2I0/π = 20/π = 6.37 A.

Worked example 4.4: Mains frequency is 50 Hz. How long after passing through zero does the voltage reach half its peak?

Solution: sin ωt = 1/2 gives ωt = π/6. t = (π/6)/(100π) = 1/600 s ≈ 1.67 ms. That is T/12.

Worked example 4.5: An AC of rms value 2 A flows through a 50 Ω resistor for one minute. Find the heat produced.

Solution: H = Irms²Rt = 4 × 50 × 60 = 12000 J = 12 kJ. A steady 2 A DC would give the same heat; that is the meaning of rms.

Worked example 4.6: Find the instantaneous voltage at t = 1/600 s for v = 311 sin(100πt) V.

Solution: 100π × 1/600 = π/6. v = 311 × 0.5 = 155.5 V.

Worked example 4.7: v = 100 sin ωt volt and i = 5 sin(ωt − π/3) ampere in a circuit. Which leads, and by how much?

Solution: The voltage phase is ωt; the current phase is ωt − π/3. The voltage is ahead by π/3 = 60°. So the current lags the voltage by 60°.

Worked example 4.8 (NEET-hard): A current is i = (4 + 3 sin ωt) A. Find its rms value.

Solution: Mean of i² = 16 + 0 + 9/2 = 20.5. Irms = √20.5 ≈ 4.53 A. Note: the answer is not √(4² + 3²) = 5, and not 4 + 3/√2.

Quick revision

  • i = I0 sin(ωt + φ); ω = 2πf; Indian mains 220 V, 50 Hz, ω ≈ 314 rad/s.

  • Full-cycle average of a sine: zero. Half-cycle average: 2I0/π ≈ 0.637I0.

  • Irms = I0/√2 ≈ 0.707I0. AC meters read rms.

  • 220 V rms means about 311 V peak and 622 V peak-to-peak.

  • Form factor of a sine = 1.11.

  • Square wave: rms = peak. Half-wave rectified: rms = I0/2, average = I0/π.

  • Phasor: rotating arrow; vertical projection = instantaneous value; add phasors as vectors.

NEET traps

  • Treating 220 V as the peak value. Mains values are rms.

  • Using I0/√2 for a square or triangular wave. It is for sine waves only.

  • Giving 2I0/π as the full-cycle average. Over a full cycle a sine averages to zero.

  • Adding rms values of two phase-shifted voltages directly. Add phasors, not numbers.

  • Mixing f and ω: in sin(314t), f = 50 Hz, not 314 Hz.

  • For i = A + B sin ωt, writing rms as √(A² + B²). It is √(A² + B²/2).

Practice MCQs: Chapter 4

Level 1: Concept check

1. The frequency of the domestic AC supply in India is (a) 60 Hz (b) 50 Hz (c) 100 Hz (d) 25 Hz

2. The rms value of a sinusoidal current of peak I0 is (a) I0/2 (b) √2 I0 (c) I0/√2 (d) 2I0/π

3. The average value of a sinusoidal current over one complete cycle is (a) I0 (b) I0/√2 (c) 2I0/π (d) zero

4. An AC ammeter connected in a circuit reads the (a) rms value (b) peak value (c) average value over a full cycle (d) peak-to-peak value

5. The average value of a sinusoidal current over a positive half cycle is (a) I0/√2 (b) 2I0/π (c) I0/π (d) I0/2

6. The frequency of the current i = 5 sin(100πt) A is (a) 100 Hz (b) 100π Hz (c) 314 Hz (d) 50 Hz

7. The peak value of a 220 V (rms) supply is about (a) 156 V (b) 220 V (c) 311 V (d) 440 V

8. In a phasor diagram, the instantaneous value of a quantity is given by (a) the length of the phasor (b) the projection of the phasor on the vertical axis (c) the angle of the phasor (d) the area swept by the phasor

9. AC is preferred to DC for sending power over long distances mainly because (a) AC voltage can be stepped up and down by transformers (b) AC is safer to touch (c) AC travels faster in wires (d) AC has no heating loss

10. The peak-to-peak value of a 220 V (rms) supply is about (a) 440 V (b) 311 V (c) 880 V (d) 622 V

Level 2: NEET standard

11. An emf is e = 200 sin(314t) V. Its rms value is about (a) 141 V (b) 200 V (c) 100 V (d) 282 V

12. For a 50 Hz AC, the shortest time for the current to rise from zero to its peak is (a) 10 ms (b) 20 ms (c) 5 ms (d) 2.5 ms

13. For a 50 Hz AC, the shortest time for the current to rise from zero to half its peak value is about (a) 5 ms (b) 2.5 ms (c) 3.33 ms (d) 1.67 ms

14. An AC of rms value 3 A flows through a 20 Ω resistor for 2 minutes. The heat produced is (a) 10.8 kJ (b) 21.6 kJ (c) 43.2 kJ (d) 7.2 kJ

15. A sinusoidal current has a peak of 10 A. Its average over a half cycle is about (a) 6.37 A (b) 7.07 A (c) 5 A (d) 3.18 A

16. A square-wave current switches between +4 A and −4 A for equal times. Its rms value is (a) 2.83 A (b) 2 A (c) 4 A (d) zero

17. A half-wave rectified sine current has a peak of 10 A. Its rms value is (a) 7.07 A (b) 3.18 A (c) 10 A (d) 5 A

18. In a circuit, v = 50 sin(ωt + π/6) V and i = 2 sin(ωt − π/3) A. The current (a) leads the voltage by π/2 (b) lags the voltage by π/2 (c) lags the voltage by π/6 (d) is in phase with the voltage

19. For a sinusoidal current, the ratio of rms value to half-cycle average value is about (a) 1.11 (b) 0.90 (c) 1.41 (d) 0.637

20. The current in a wire is i = 4 sin ωt + 3 cos ωt ampere. Its rms value is (a) 5 A (b) 7/√2 A (c) 5/√2 A (d) 7 A

21. For v = 200 sin(100πt) V, the voltage at t = 1/300 s is about (a) 100 V (b) 141 V (c) 200 V (d) 173 V

22. A 60 W, 220 V bulb runs on AC mains. The peak current through it is about (a) 0.27 A (b) 0.39 A (c) 0.19 A (d) 0.55 A

Level 3: Challenge

23. A current is i = (3 + 4 sin ωt) A. Its rms value is (a) √17 A (b) 5 A (c) 7 A (d) √12.5 A

24. A sawtooth current rises uniformly from 0 to I0 over each period and then drops to zero instantly. Its rms value is (a) I0/√2 (b) I0/2 (c) I0/√3 (d) I0/3

25. A neon lamp lights only when the voltage across it (either sign) is at least 155.5 V. It is connected to 220 V, 50 Hz mains. For how long does it glow in each second? (a) 1/2 s (b) 2/3 s (c) 1/3 s (d) 3/4 s

26. For a 50 Hz sinusoidal current, the shortest time from zero to I0/√2 is (a) 5 ms (b) 1.25 ms (c) 3.33 ms (d) 2.5 ms

27. An AC of peak 2 A and a DC of 2 A pass through identical resistors for the same time. The ratio of heat produced (AC : DC) is (a) 1 : 2 (b) 2 : 1 (c) 1 : √2 (d) 1 : 1

28. Two sources v1 = 30 sin ωt and v2 = 40 cos ωt (in volts) are joined in series. The rms value of the total voltage is about (a) 70 V (b) 35.4 V (c) 50 V (d) 49.5 V

29. Assertion (A): The average value of a sinusoidal AC over one complete cycle is zero. Reason (R): AC voltmeters are calibrated to read rms values. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: The rms value of a sinusoidal current is about 70.7% of its peak value. Statement II: The half-cycle average of a sinusoidal current is greater than its rms value. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1bIndian grid runs at 50 Hz
2cMean of sin² is ½
3dPositive and negative halves cancel
4aAC meters are calibrated in rms
5bIntegral over half cycle gives 2I0/π
6df = 100π/2π = 50 Hz
7c220 × 1.414 ≈ 311 V
8bVertical projection of rotating arrow
9aTransformers work only with changing current
10d2 × 311 ≈ 622 V
11a200/√2 ≈ 141 V
12cT/4 = 20/4 ms
13dωt = π/6 gives t = T/12
14b9 × 20 × 120 = 21600 J
15a2 × 10/π = 6.37 A
16ci² is always 16, so rms = 4 A
17dMean of i² = I0²/4 over full cycle
18bPhase gap π/6 + π/3 = π/2, current behind
19aπ/(2√2) ≈ 1.11
20cPeak √(16 + 9) = 5 A
21d200 sin(π/3) = 173 V
22bIrms = 60/220 = 0.273 A; times √2
23a9 + 16/2 = 17
24cMean of (I0t/T)² = I0²/3
25b155.5 V is half of 311 V; sin above ½ for 2/3 of the time
26dωt = π/4 gives T/8 = 2.5 ms
27aAC rms is 2/√2, heat ∝ I²
28bPeak 50 V; 50/√2
29bBoth true, but meter calibration does not explain the zero average
30c0.637I0 is less than 0.707I0

Chapter 4 revision sheet

One-page summary

  • Sinusoidal AC: v = V0 sin ωt, with ω = 2πf = 2π/T. V0 is the peak (amplitude).

  • Indian mains: 220 V rms, 50 Hz, so V0 ≈ 311 V, ω = 100π rad/s, T = 20 ms.

  • A 50 Hz current changes direction 100 times each second (twice per cycle).

  • Average over a full cycle of a sine wave is zero.

  • Average over a half cycle: Iavg = 2I0/π ≈ 0.637 I0.

  • rms value: the steady current that gives the same heating. For a sine wave Irms = I0/√2 ≈ 0.707 I0.

  • AC meters (hot-wire, moving-iron) read rms. Ratings like 220 V and 5 A are rms values.

  • Form factor = rms/average (half cycle) = π/(2√2) ≈ 1.11 for a sine wave.

  • Other waves: square wave ±I0 has rms I0; half-wave rectified sine has rms I0/2 and average I0/π; triangular or sawtooth wave has rms I0/√3.

  • Mixed: for i = Idc + I0 sin ωt, Irms = √(Idc² + I0²/2). For a sin ωt + b cos ωt, amplitude is √(a² + b²).

  • Phasor: an arrow of length equal to the peak value, rotating anticlockwise at ω. Its projection on the vertical axis gives the instantaneous value.

  • The angle between two phasors is the phase difference; the one ahead (anticlockwise) leads.

  • AC is used because transformers can step its voltage up and down, which cuts transmission loss.

Must-remember table

WaveformrmsAverage
Sine, full cycleI0/√2 = 0.707 I00
Sine, half cycleI0/√22I0/π = 0.637 I0
Square wave ±I0I00 (full cycle)
Half-wave rectified sineI0/2I0/π = 0.318 I0
Full-wave rectified sineI0/√22I0/π
Triangular / sawtooth (peak I0)I0/√3 = 0.577 I00 for symmetric ± wave
Indian mains220 Vpeak 311 V, 50 Hz

Memory aids

  • "Seven-oh-seven goes rms": for a sine wave, rms is 0.707 of the peak, like a Boeing 707 that flies lower than its peak.

  • "Six-three-seven averages heaven": half-cycle average is 0.637 of peak (2/π).

  • "HALF-wave halves": rms of a half-wave rectified sine is exactly half the peak.

  • "Square is square": a square wave has rms equal to its peak because i² never changes.

  • "Anticlockwise is ahead": in a phasor diagram the arrow further anticlockwise leads.

Concept connections

  • Heating effect and power P = I²R come from Physics Book 12: Current Electricity.

  • Sine functions, phase and angular frequency are the same as in SHM in Physics Book 10: Oscillations and Waves.

  • Rectified waveforms reappear with diodes in Physics Book 19: Electronic Devices.

Practice MCQs: Chapter 4, Level 4 (new NEET pattern)

31. For i = I0 sin ωt with I0 = 10 A, match List I with List II.

List I:

  • A. rms value

  • B. Average over a full cycle

  • C. Average over a half cycle

  • D. Peak-to-peak value

List II:

  • (i) 0

  • (ii) 6.37 A

  • (iii) 20 A

  • (iv) 7.07 A

(a) A-ii, B-i, C-iv, D-iii (b) A-iv, B-i, C-ii, D-iii (c) A-iv, B-iii, C-ii, D-i (d) A-iii, B-i, C-ii, D-iv

32. Match the waveform (List I) with the ratio rms/peak (List II).

List I:

  • A. Sine wave

  • B. Symmetric square wave

  • C. Half-wave rectified sine

  • D. Symmetric triangular wave

List II:

  • (i) 1

  • (ii) 0.5

  • (iii) 0.707

  • (iv) 0.577

(a) A-i, B-iii, C-ii, D-iv (b) A-iii, B-i, C-iv, D-ii (c) A-iii, B-i, C-ii, D-iv (d) A-iv, B-i, C-ii, D-iii

33. For v = 311 sin(100πt) volt, match List I with List II.

List I:

  • A. Peak voltage

  • B. rms voltage

  • C. Frequency

  • D. Time period

List II:

  • (i) 50 Hz

  • (ii) 20 ms

  • (iii) 220 V

  • (iv) 311 V

(a) A-iii, B-iv, C-i, D-ii (b) A-iv, B-iii, C-ii, D-i (c) A-iv, B-i, C-iii, D-ii (d) A-iv, B-iii, C-i, D-ii

34. Match the need (List I) with the value of AC that answers it (List II).

List I:

  • A. The steady current that gives the same heating

  • B. The mean value over a complete cycle

  • C. The value used to find charge sent in one half cycle

  • D. The voltage that cable insulation must withstand

List II:

  • (i) Zero

  • (ii) Peak value

  • (iii) rms value

  • (iv) Half-cycle average

(a) A-iii, B-i, C-iv, D-ii (b) A-ii, B-i, C-iv, D-iii (c) A-iii, B-iv, C-i, D-ii (d) A-iv, B-i, C-iii, D-ii

35. How many of the following statements are correct?

  • A. For sinusoidal AC, Irms = 0.707 I0.

  • B. The average of a sinusoidal current over a full cycle is 2I0/π.

  • C. The 220 V of Indian mains is an rms value.

  • D. A 50 Hz current changes direction 100 times per second.

  • E. The form factor of a sine wave is about 1.11.

(a) 3 (b) 4 (c) 5 (d) 2

36. Choose the correct set of statements about phasors.

  • A. A phasor rotates anticlockwise with angular speed ω.

  • B. Its projection on the vertical axis gives the instantaneous value.

  • C. Two quantities in phase have phasors at 90° to each other.

  • D. The angle between two phasors is their phase difference.

(a) A and C only (b) B, C and D only (c) A, B, C and D (d) A, B and D only

37. How many of the following statements are correct?

  • A. The rms value of i = 3 + 4 sin ωt (A) is 5 A.

  • B. The rms value of a square wave of ±5 A is 5 A.

  • C. The rms value of a half-wave rectified sine of peak I0 is I0/2.

  • D. The average of a half-wave rectified sine of peak I0, over a full cycle, is I0/π.

(a) 3 (b) 2 (c) 4 (d) 1

38. Choose the correct set of statements.

  • A. AC voltage can be stepped up or down with a transformer.

  • B. Sending power at high voltage cuts I²R loss in the lines.

  • C. Electroplating can be done directly with AC.

  • D. The peak value of 220 V rms mains is about 311 V.

(a) A, B and D only (b) A and C only (c) B and D only (d) A, B, C and D

39. A current waveform is +4 A for the first half of each period and −2 A for the second half. Its average and rms values over a full period are: (a) 0, 3.16 A (b) 1 A, 3.16 A (c) 1 A, 3 A (d) 3 A, 3 A

40. A voltage v = V0 sin ωt (period T) is sampled:

t0T/12T/4T/2
v (V)0501000

The value at t = T/8 and the rms voltage are: (a) 50 V, 70.7 V (b) 70.7 V, 100 V (c) 86.6 V, 70.7 V (d) 70.7 V, 70.7 V

41. A phasor diagram shows the voltage phasor of length 10 V and a current phasor of length 2 A placed 60° anticlockwise from it. If v = 10 sin ωt, the current is: (a) i = 2 sin(ωt − π/3) (b) i = 2 cos(ωt + π/3) (c) i = 2 sin(ωt + π/3) (d) i = 2 sin(ωt + 2π/3)

Case for Q42–43: An electric kettle rated 1100 W, 220 V is used on 220 V (rms), 50 Hz mains. Treat it as a pure resistor.

42. The peak current through the kettle is about: (a) 5 A (b) 3.54 A (c) 10 A (d) 7.07 A

43. Starting from an instant when the current is zero, the least time for it to reach its peak is: (a) 5 ms (b) 10 ms (c) 2.5 ms (d) 20 ms

44. The rms value of i = 4 sin ωt + 3 cos ωt (in A) is: (a) 5 A (b) 4.95 A (c) 3.54 A (d) 7 A

45. For 50 Hz sinusoidal AC, the time taken for the current to rise from half its peak value to its peak value is: (a) 1.67 ms (b) 3.33 ms (c) 5 ms (d) 2.5 ms

Level 4 answer key

QAnsReason
31b10/√2 = 7.07 A; 0; 20/π = 6.37 A; 2 × 10 = 20 A
32c1/√2, 1, 1/2, 1/√3
33d311/√2 ≈ 220 V; 100π = 2πf gives 50 Hz; T = 1/50 s
34aHeating uses rms; full-cycle mean is zero; charge uses half-cycle average; insulation must stand the peak
35bA, C, D, E true; full-cycle average is zero
36dIn-phase quantities have phasors along the same line, so C is false
37aB, C, D true; rms of A is √(9 + 8) = 4.12 A
38aElectroplating needs DC, so C is false
39bAverage = (4 − 2)/2 = 1 A; rms = √((16 + 4)/2) = √10 = 3.16 A
40dsin 30° = 0.5 gives V0 = 100 V; 100 sin 45° = 70.7 V; rms = 100/√2
41cAnticlockwise 60° means current leads by π/3
42dIrms = 1100/220 = 5 A; I0 = 5√2 = 7.07 A
43aZero to peak is T/4 = 20/4 = 5 ms
44cAmplitude √(16 + 9) = 5 A; rms = 5/√2 = 3.54 A
45bHalf peak at T/12, peak at T/4; difference T/6 = 3.33 ms
21 min left
‹
›