Chapter 8 of 12 · 22 min read

Chapter 6: Series LCR Circuit and Resonance

What you will learn

  • How to add the voltages across R, L and C using phasors.

  • Impedance Z = √(R² + (XL − XC)²) and the phase angle tan φ = (XL − XC)/R.

  • How to tell whether a circuit is inductive, capacitive or resistive.

  • Series resonance: f0 = 1/(2π√(LC)), maximum current, and voltage build-up across L and C.

  • Quality factor and bandwidth, and why a radio can pick out one station.

6.1 Phasor analysis of the series LCR circuit

A resistor R, an inductor L and a capacitor C are joined in series to a source v = V0 sin ωt. Being in series, the same current i = I0 sin(ωt − φ) flows through all three. So we draw the current phasor first, and place each voltage relative to it.

  • VR = I0R, in phase with the current.

  • VL = I0XL, leading the current by 90°.

  • VC = I0XC, lagging the current by 90°.

VL and VC point in exactly opposite directions. Their resultant is (VL − VC), at right angles to VR. The source voltage is the vector sum:

V02=VR2+(VL−VC)2=I02[R2+(XL−XC)2]V_0^2 = V_R^2 + (V_L - V_C)^2 = I_0^2\left[R^2 + (X_L - X_C)^2\right]

So the peak current is I0 = V0/Z, where Z is the impedance:

Z=R2+(XL−XC)2Z = \sqrt{R^2 + (X_L - X_C)^2}

The same relation holds for rms values: Irms = Vrms/Z. The angle by which the source voltage leads the current is:

tan⁡ϕ=XL−XCR,cos⁡ϕ=RZ\tan\phi = \frac{X_L - X_C}{R}, \qquad \cos\phi = \frac{R}{Z}

The right-angled triangle with sides R and (XL − XC) and hypotenuse Z is the impedance triangle. It is the voltage triangle divided by the current.

Figure 6.1 · Series LCR voltage phasors and the impedance triangle
Figure 6.1 · Series LCR voltage phasors and the impedance triangle

VL and VC point opposite ways, so only their difference adds at right angles to VR; dividing every side by I turns the voltage triangle into the impedance triangle.

A practical point: voltmeter readings across R, L and C do not add up to the source voltage. A student who measures VR = 40 V, VL = 90 V and VC = 60 V on a 50 V supply has not made a mistake. They add as phasors: √(40² + 30²) = 50 V.

6.2 Inductive, capacitive or resistive?

ConditionNature of circuitPhase of currentTypical frequency range
XL greater than XCInductiveLags voltage by φAbove f0
XC greater than XLCapacitiveLeads voltage by φBelow f0
XL = XCPurely resistiveIn phaseAt f0 (resonance)

The same formula covers circuits with only two elements. Put the missing reactance equal to zero.

CircuitZtan φCurrent
RL series√(R² + XL²)XL/RLags, 0 to 90°
RC series√(R² + XC²)XC/R (lead)Leads, 0 to 90°
LC seriesDifference of XL and XCInfiniteExactly 90° lag or lead

6.3 Resonance

As frequency rises, XL grows and XC falls. At one frequency they become equal. There the reactances cancel, Z = R (its smallest value), and the current is largest. This is series resonance.

ω0L=1ω0C⇒ω0=1LC,f0=12πLC\omega_0 L = \frac{1}{\omega_0 C} \quad\Rightarrow\quad \omega_0 = \frac{1}{\sqrt{LC}}, \qquad f_0 = \frac{1}{2\pi\sqrt{LC}}

At resonance:

  • Z = R and Irms = Vrms/R, the maximum possible.

  • Current and source voltage are in phase (φ = 0). Power factor is 1.

  • VL and VC are equal in size and opposite in phase. Together they give zero. A voltmeter across the L-C pair reads zero.

  • Each of VL and VC alone can be many times the source voltage.

  • f0 does not depend on R.

Resonance needs both L and C. An RL or RC circuit cannot resonate.

The resonance curve (current against frequency) has a peak at f0. A smaller R gives a taller, narrower peak. A larger R gives a lower, flatter one. The peak stays at the same f0.

Figure 6.2 · Resonance curves for two values of R (schematic)
Figure 6.2 · Resonance curves for two values of R (schematic)

Both curves peak at the same ω0; the smaller resistance gives the taller, narrower peak, and its half-power width is R/L.

6.4 Sharpness: quality factor and bandwidth

The half-power frequencies ω1 and ω2 are where the current falls to Imax/√2. (Power ∝ I², so power falls to half.) The bandwidth is the gap between them. For a sharp peak:

Δω=ω2−ω1=RL\Delta\omega = \omega_2 - \omega_1 = \frac{R}{L}

The quality factor Q measures sharpness:

Q=ω0Δω=ω0LR=1ω0CR=1RLCQ = \frac{\omega_0}{\Delta\omega} = \frac{\omega_0 L}{R} = \frac{1}{\omega_0 C R} = \frac{1}{R}\sqrt{\frac{L}{C}}

Q has no unit. A large Q means a narrow, tall peak. Q also tells the voltage build-up at resonance: VL = VC = Q × Vsource. With Q = 10 and a 20 V source, the inductor and capacitor each carry 200 V.

Tuning a radio. The antenna picks up signals from many stations at once. A variable capacitor changes f0 of an LC circuit inside the set. Only the station whose frequency matches f0 drives a large current. A high-Q circuit rejects the stations next to it on the dial.

Worked example 6.1: A series circuit has R = 30 Ω, XL = 80 Ω and XC = 40 Ω on a 200 V rms supply. Find Z, the current, the phase angle and each voltage.

Solution: Z = √(30² + 40²) = 50 Ω. Irms = 200/50 = 4 A. tan φ = 40/30, so φ ≈ 53°. XL is larger, so the current lags. VR = 120 V, VL = 320 V, VC = 160 V. Check: √(120² + 160²) = 200 V.

Worked example 6.2: In a series LCR circuit the voltmeter readings are VR = 40 V, VL = 90 V, VC = 60 V. Find the supply voltage.

Solution: V = √(40² + (90 − 60)²) = √(1600 + 900) = 50 V.

Worked example 6.3: Find the resonant frequency for L = 0.1 H and C = 10 μF.

Solution: LC = 10⁻⁶, so ω0 = 1/10⁻³ = 1000 rad/s. f0 = 1000/2π = 159 Hz.

Worked example 6.4: Find f0 for L = (1/π) H and C = (1/π) μF.

Solution: √(LC) = √(10⁻⁶/π²) = 10⁻³/π. f0 = 1/(2π × 10⁻³/π) = 1/(2 × 10⁻³) = 500 Hz.

Worked example 6.5: An RL circuit has R = 6 Ω and XL = 8 Ω on a 100 V rms supply. Find the current and phase angle.

Solution: Z = √(36 + 64) = 10 Ω. I = 10 A. tan φ = 8/6, so φ ≈ 53°, current lagging.

Worked example 6.6: An RC circuit has R = 40 Ω and XC = 30 Ω. Find Z and the phase.

Solution: Z = √(1600 + 900) = 50 Ω. tan φ = 30/40, so φ ≈ 37°, with the current leading.

Worked example 6.7: A series circuit has R = 10 Ω, L = 0.1 H and C = 10 μF, on a 20 V rms supply at resonance. Find Q, the bandwidth, the current and VL.

Solution: ω0 = 1000 rad/s. Q = ω0L/R = 100/10 = 10. Δω = R/L = 100 rad/s. I = 20/10 = 2 A. VL = IXL = 2 × 100 = 200 V, which is Q × 20 V.

Worked example 6.8 (NEET-hard): A 0.4 H coil (negligible resistance) and a resistor are in series with a capacitor on 50 Hz mains. What capacitance gives resonance? (Take π² = 10.)

Solution: C = 1/(ω0²L). ω0² = (100π)² = 10⁴π² = 10⁵. C = 1/(10⁵ × 0.4) = 2.5 × 10⁻⁵ F = 25 μF.

Quick revision

  • Z = √(R² + (XL − XC)²); I = V/Z for rms or peak values.

  • tan φ = (XL − XC)/R; cos φ = R/Z.

  • XL greater than XC: inductive, current lags. XC greater: capacitive, current leads.

  • Resonance: XL = XC, ω0 = 1/√(LC), Z = R, current maximum, φ = 0.

  • f0 is independent of R; R only sets the height and width of the peak.

  • Bandwidth Δω = R/L; Q = ω0L/R = (1/R)√(L/C) = ω0/Δω.

  • At resonance VL = VC = Q × V.

NEET traps

  • Adding VR, VL and VC as plain numbers. Add them as phasors.

  • Writing Z = √(R² + XL² + XC²). XL and XC subtract.

  • Using ω0 = 1/√(LC) as a frequency in Hz. Divide by 2π for f0.

  • Thinking R changes the resonant frequency. It does not.

  • Assuming VL at resonance cannot exceed the source voltage. It can, by a factor Q.

  • Getting the nature wrong below f0. Below resonance XC is larger, so the circuit is capacitive.

Practice MCQs: Chapter 6

Level 1: Concept check

1. The impedance of a series LCR circuit is (a) R + XL + XC (b) √(R² + XL² + XC²) (c) √(R² + (XL − XC)²) (d) R + XL − XC

2. The resonant frequency of a series LCR circuit is (a) 1/(2π√(LC)) (b) 2π√(LC) (c) √(LC)/2π (d) √(L/C)/2π

3. At resonance, the impedance of a series LCR circuit equals (a) zero (b) XL (c) XL + XC (d) R

4. At resonance, the phase difference between the source voltage and the current is (a) π/2 (b) zero (c) π (d) π/4

5. In a series LCR circuit with XL greater than XC, the circuit is (a) capacitive, current leading (b) purely resistive (c) inductive, current lagging (d) at resonance

6. The quality factor of a series LCR circuit is (a) (1/R)√(L/C) (b) R√(L/C) (c) (1/R)√(C/L) (d) R√(C/L)

7. The resistance in a series LCR circuit is increased. The resonance curve (a) becomes sharper (b) shifts to a higher frequency (c) shifts to a lower frequency (d) has a lower peak and becomes flatter

8. A series LCR circuit at resonance is called an acceptor circuit because it (a) draws minimum current at f0 (b) draws maximum current at f0 (c) has zero impedance (d) blocks the frequency f0

9. Resonance is possible in a (a) series RL circuit (b) series RC circuit (c) series LCR circuit (d) purely resistive circuit

10. The phase angle φ of a series LCR circuit is given by (a) tan φ = (XL − XC)/R (b) tan φ = R/(XL − XC) (c) sin φ = R/Z (d) cos φ = (XL − XC)/Z

Level 2: NEET standard

11. A series circuit has R = 30 Ω, XL = 60 Ω and XC = 20 Ω. Its impedance is (a) 110 Ω (b) 50 Ω (c) 70 Ω (d) 40 Ω

12. In a series LCR circuit, VR = 30 V, VL = 70 V and VC = 30 V. The supply voltage is (a) 130 V (b) 70 V (c) 40 V (d) 50 V

13. For L = 0.1 H and C = 10 μF, the resonant angular frequency is (a) 1000 rad/s (b) 100 rad/s (c) 10⁴ rad/s (d) 159 rad/s

14. For L = (1/π) H and C = (4/π) μF, the resonant frequency is (a) 500 Hz (b) 125 Hz (c) 250 Hz (d) 1000 Hz

15. An RL series circuit has R = 8 Ω and XL = 6 Ω on a 100 V rms supply. The current is (a) 7.1 A (b) 10 A (c) 12.5 A (d) 16.7 A

16. An RC series circuit has R = 100 Ω and XC = 100 Ω. The current (a) lags the voltage by 45° (b) leads the voltage by 90° (c) is in phase with the voltage (d) leads the voltage by 45°

17. A series LCR circuit has R = 5 Ω, L = 0.2 H and C = 20 μF. Its quality factor is (a) 20 (b) 10 (c) 40 (d) 5

18. At resonance, a series LCR circuit has R = 5 Ω and XL = XC = 100 Ω, on a 10 V rms source. The rms voltage across the inductor is (a) 10 V (b) 100 V (c) 200 V (d) 20 V

19. The capacitance needed with a 1 H coil for resonance at 50 Hz is (take π² = 10) (a) 1 μF (b) 100 μF (c) 5 μF (d) 10 μF

20. A series LCR circuit is driven at a frequency below its resonant frequency. The circuit behaves as (a) inductive (b) capacitive (c) purely resistive (d) an open circuit

21. The capacitance in a series LCR circuit is made four times, with L unchanged. The resonant frequency (a) halves (b) doubles (c) becomes one-fourth (d) stays the same

22. A series LCR circuit has R = 20 Ω and L = 0.5 H. Its bandwidth (in rad/s) is (a) 10 (b) 20 (c) 40 (d) 80

Level 3: Challenge

23. A series LCR circuit with R = 10 Ω draws 2 A at resonance. The frequency is changed so that XL − XC = 10 Ω, at the same source voltage. The current becomes about (a) 1 A (b) 1.41 A (c) 2 A (d) 0.71 A

24. A voltage v = 100 sin(1000t) V drives R = 100 Ω, L = 0.2 H and C = 10 μF in series. The current, in ampere, is (a) 1 sin(1000t) (b) 0.707 sin(1000t + π/4) (c) 0.5 sin(1000t − π/4) (d) 0.707 sin(1000t − π/4)

25. A series LCR circuit is at resonance. A voltmeter connected across the inductor and capacitor together reads (a) zero (b) VL + VC (c) the source voltage (d) 2VL

26. A series LCR circuit has ω0 = 1000 rad/s and bandwidth 100 rad/s. Its half-power angular frequencies are about (a) 900 and 1100 rad/s (b) 990 and 1010 rad/s (c) 950 and 1050 rad/s (d) 1000 and 1100 rad/s

27. In a series LCR circuit, R and L are both doubled while C is unchanged. The quality factor becomes (a) 2 times (b) 1/√2 times (c) √2 times (d) half

28. A series LCR circuit with R = 40 Ω and XL = 50 Ω draws 4 A from a 200 V rms source, and the current lags the voltage. The capacitive reactance is (a) 20 Ω (b) 80 Ω (c) 30 Ω (d) 10 Ω

29. Assertion (A): At resonance, the impedance of a series LCR circuit is minimum. Reason (R): At resonance, the current lags the source voltage by π/2. (a) Both true, R explains A (b) Both true, R does not explain A (c) A true, R false (d) A false, R true

30. Statement I: Increasing the capacitance in a series LCR circuit lowers its resonant frequency. Statement II: A higher quality factor gives a sharper resonance curve. (a) Both true (b) Both false (c) I true, II false (d) I false, II true

Answer key with reasons

QAnsReason
1cVL and VC are opposite phasors
2aXL = XC gives ω0 = 1/√(LC)
3dReactances cancel
4bPurely resistive at resonance
5cNet reactance is inductive
6aQ = ω0L/R with ω0 = 1/√(LC)
7df0 stays; peak = V/R falls
8bImpedance is minimum at f0
9cNeeds both L and C
10aFrom the impedance triangle
11b√(30² + 40²) = 50 Ω
12d√(30² + 40²) = 50 V
13a1/√(10⁻⁶) = 1000 rad/s
14c√(LC) = 2 × 10⁻³/π, f0 = 250 Hz
15bZ = 10 Ω
16dtan φ = 1, capacitive so current leads
17aω0 = 500 rad/s; 500 × 0.2/5
18cI = 2 A; VL = 2 × 100
19dC = 1/(10⁵ × 1) F
20bXC is larger below f0
21af0 ∝ 1/√C
22cR/L = 20/0.5
23bZ = 10√2 Ω; V = 20 V; I = √2 A
24dXL = 200, XC = 100, Z = 141 Ω, current lags 45°
25aVL and VC cancel at resonance
26cω0 ± Δω/2
27bQ ∝ √L/R gives √2/2
28aZ = 50 so net reactance 30 Ω, inductive
29cAt resonance current is in phase
30af0 ∝ 1/√C; high Q means narrow peak

Chapter 6 revision sheet

One-page summary

  • In a series LCR circuit the same current flows through all three; VR is in phase with i, VL leads i by 90°, VC lags i by 90°.

  • Voltages add as phasors, not as numbers: V = √(VR² + (VL − VC)²).

  • Impedance: Z = √(R² + (XL − XC)²). Irms = Vrms/Z.

  • Phase angle: tan φ = (XL − XC)/R; cos φ = R/Z.

  • XL > XC: inductive, current lags. XL < XC: capacitive, current leads. XL = XC: resistive.

  • RL circuit: Z = √(R² + XL²). RC circuit: Z = √(R² + XC²).

  • Resonance: XL = XC, so ω0 = 1/√(LC) and f0 = 1/(2π√(LC)). f0 does not depend on R.

  • At resonance: Z = R (minimum), current is maximum V/R, φ = 0, power factor 1.

  • At resonance VL and VC are equal and opposite; each can be much larger than the source voltage (Q times it).

  • Below f0 the circuit is capacitive; above f0 it is inductive.

  • Half-power frequencies ω1, ω2: current is Imax/√2. Bandwidth Δω = ω2 − ω1 = R/L.

  • Quality factor Q = ω0L/R = 1/(ω0CR) = (1/R)√(L/C) = ω0/Δω. Higher Q means a sharper peak.

  • Resonance needs both L and C; an RL or RC circuit cannot resonate. Radio tuning uses a variable C.

Must-remember table

QuantityFormulaNote
Impedance√(R² + (XL − XC)²)ohm
Phase angletan φ = (XL − XC)/R+ means current lags
Resonant angular frequency1/√(LC)independent of R
Resonant frequency1/(2π√(LC))Hz
Current at resonanceV/Rmaximum
BandwidthR/Lrad/s
Quality factorω0L/R = (1/R)√(L/C)no unit
Voltage across L at resonanceQ × Vcan exceed supply

Memory aids

  • "Z is the hypotenuse": R on the base, (XL − XC) on the height, Z the long side of the triangle.

  • "At resonance the reactances cancel like equal tug-of-war teams": L and C pull equally in opposite directions, leaving only R.

  • "Low R, high Q, sharp peak": less resistance gives a taller, narrower resonance curve.

  • "Below is C, above is L": below f0 the capacitor wins; above f0 the inductor wins.

Concept connections

  • Reactances XL and XC come from Chapter 5 of this book; power at resonance is in Chapter 7.

  • Resonance and sharpness are the electrical twin of forced oscillations in Physics Book 10: Oscillations and Waves.

  • Tuning circuits that select radio stations link to Physics Book 15: Electromagnetic Waves.

Practice MCQs: Chapter 6, Level 4 (new NEET pattern)

31. Match the series circuit (List I) with its impedance (List II).

List I:

  • A. R = 30 Ω, XL = 40 Ω

  • B. R = 6 Ω, XC = 8 Ω

  • C. R = 12 Ω, XL = 20 Ω, XC = 4 Ω

  • D. R = 25 Ω, XL = XC

List II:

  • (i) 10 Ω

  • (ii) 20 Ω

  • (iii) 25 Ω

  • (iv) 50 Ω

(a) A-iv, B-ii, C-i, D-iii (b) A-iv, B-i, C-ii, D-iii (c) A-i, B-iv, C-ii, D-iii (d) A-iii, B-i, C-ii, D-iv

32. Match the condition in a series LCR circuit (List I) with its nature (List II).

List I:

  • A. XL > XC

  • B. XL < XC

  • C. XL = XC

  • D. R = 0 and XL = XC (ideal)

List II:

  • (i) Capacitive, current leads

  • (ii) Impedance zero, current unlimited

  • (iii) Inductive, current lags

  • (iv) Resistive, power factor 1

(a) A-i, B-iii, C-iv, D-ii (b) A-iii, B-i, C-ii, D-iv (c) A-iii, B-iv, C-i, D-ii (d) A-iii, B-i, C-iv, D-ii

33. A series LCR circuit resonates at f0. Match the change (List I) with the new resonant frequency (List II).

List I:

  • A. L doubled

  • B. C made four times

  • C. Both L and C halved

  • D. R doubled

List II:

  • (i) f0 (unchanged)

  • (ii) f0/2

  • (iii) 2f0

  • (iv) f0/√2

(a) A-iv, B-ii, C-iii, D-i (b) A-ii, B-iv, C-iii, D-i (c) A-iv, B-iii, C-ii, D-i (d) A-iv, B-ii, C-i, D-iii

34. A series circuit has L = 1 H, C = 1 μF, R = 10 Ω and a 100 V rms variable-frequency source. Match List I with List II.

List I:

  • A. Resonant angular frequency

  • B. Quality factor

  • C. Current at resonance

  • D. Bandwidth Δω

List II:

  • (i) 10 A

  • (ii) 100

  • (iii) 10 rad/s

  • (iv) 1000 rad/s

(a) A-ii, B-iv, C-i, D-iii (b) A-iv, B-ii, C-iii, D-i (c) A-iv, B-ii, C-i, D-iii (d) A-iv, B-i, C-ii, D-iii

35. How many statements about a series LCR circuit at resonance are correct?

  • A. The impedance is minimum and equals R.

  • B. The current is in phase with the applied voltage.

  • C. The voltages across L and C are equal in size and opposite in phase.

  • D. The voltage across L can exceed the source voltage.

  • E. The power factor is zero.

(a) 4 (b) 3 (c) 5 (d) 2

36. Choose the correct set of statements about the quality factor Q.

  • A. Q = ω0L/R.

  • B. Q = (1/R)√(L/C).

  • C. A larger R gives a sharper resonance.

  • D. Q = ω0/Δω.

(a) A and C only (b) B and C only (c) A, B, C and D (d) A, B and D only

37. How many of the following statements are correct?

  • A. Resonance can occur in a series RL circuit.

  • B. The resonant frequency of a series LCR circuit does not depend on R.

  • C. Below resonance, a series LCR circuit is capacitive.

  • D. Above resonance, the current leads the voltage.

(a) 1 (b) 2 (c) 3 (d) 4

38. A series circuit has R = 40 Ω, XL = 60 Ω, XC = 30 Ω and carries 2 A rms. Choose the correct set.

  • A. The source voltage is 260 V (the sum of VR, VL and VC).

  • B. The source voltage is 100 V.

  • C. The current lags the source voltage.

  • D. tan φ = 3/4.

(a) A and C only (b) B and D only (c) B, C and D only (d) A, C and D only

39. Two resonance curves (Irms against ω) are drawn for the same L and C with resistances R1 and R2. Curve 1 is taller and narrower; both peak at the same ω. Then: (a) R1 > R2, Q1 > Q2 (b) R1 < R2, resonant frequencies differ (c) R1 < R2, Q1 > Q2, same resonant ω (d) R1 = R2, different L

40. A series LCR circuit with L = 0.1 H is driven by a 10 V rms source of variable frequency.

f (Hz)400500600
Irms (A)0.070.500.09

Taking 500 Hz as the resonant frequency, R and C are about: (a) 20 Ω, 1.0 μF (b) 5 Ω, 1.0 μF (c) 20 Ω, 10 μF (d) 50 Ω, 1.0 μF

41. The graph of impedance Z against frequency for a series LCR circuit: (a) has a maximum at f0 (b) is constant (c) rises steadily (d) falls to a minimum value R at f0 and then rises

Case for Q42–43: A radio's tuning circuit has a fixed 10 μH coil and a variable capacitor. A listener tunes first to a 1 MHz station and then to a 2 MHz station.

42. The capacitance for the 1 MHz station is about: (a) 25.3 nF (b) 0.253 nF (c) 2.53 nF (d) 253 nF

43. The capacitance for the 2 MHz station is about: (a) 1.27 nF (b) 0.633 nF (c) 5.07 nF (d) 10.1 nF

44. A series circuit has R = 50 Ω, L = 0.5 H, C = 20 μF and a 200 V rms source tuned to resonance. The rms voltage across the inductor is about: (a) 200 V (b) 316 V (c) 0 (d) 632 V

45. In a circuit of R = 40 Ω with L only, XL = 40 Ω. With C only (L removed), XC = 20 Ω. With R, L and C all in series at the same frequency, the power factor is about: (a) 0.707 (b) 0.894 (c) 1 (d) 0.447

Level 4 answer key

QAnsReason
31b3-4-5 gives 50; 6-8-10 gives 10; √(144 + 256) = 20; resonance gives Z = R
32dLarger reactance decides the nature; R = 0 at resonance gives Z = 0
33af0 ∝ 1/√(LC); R has no effect
34cω0 = 1/√(10⁻⁶) = 1000; Q = 1000/10 = 100; I = 100/10 = 10 A; R/L = 10 rad/s
35aA, B, C, D true; power factor is 1 at resonance
36dLarger R gives a flatter, broader curve
37bB and C true; RL has no resonance; above f0 current lags
38cV = 2 × √(40² + 30²) = 100 V; XL > XC so current lags; tan φ = 30/40
39cTaller peak V/R means smaller R; narrower means higher Q; ω0 = 1/√(LC) is the same
40aR = 10/0.5 = 20 Ω; C = 1/(4π² × 500² × 0.1) = 1.01 μF
41dZ = R at f0, larger on both sides
42cC = 1/(4π²f²L) = 1/(4π² × 10¹² × 10⁻⁵) = 2.53 nF
43bC ∝ 1/f², so 2.53/4 = 0.633 nF
44dω0 = 316 rad/s, XL = 158 Ω, I = 200/50 = 4 A, VL = 632 V
45bX = 40 − 20 = 20 Ω, Z = √(1600 + 400) = 44.7 Ω, cos φ = 40/44.7 = 0.894
22 min left
‹
›