LATEST
NEETBy Pareeksha Editorial Team· ⏱ 7 min read

Mechanical Properties of Solids NEET PYQs: Solved Qs

Share𝕏fin
Alongside this guide

Find study material for your next topic

Browse the Reading Room and preview a chapter before choosing what to study.

Browse study material →
Mechanical Properties of Solids NEET PYQs: Solved Qs
On this page
  1. How often NEET asks Mechanical Properties of Solids
  2. What the questions test
  3. Solved NEET past questions
  4. 1. Matching the elastic moduli
  5. 2. Largest stretch within the elastic limit
  6. 3. Stress in a hanging wire
  7. 4. Young's modulus from a stretched length
  8. 5. Reading a stress-strain curve
  9. Key formulas
  10. Common traps
  11. How to study Mechanical Properties of Solids
  12. Frequently asked questions
  13. How many NEET questions come from Mechanical Properties of Solids?
  14. Should I skip this chapter?
  15. What is the most asked topic in this chapter?
  16. Does Young's modulus change if I cut a wire in half?

Mechanical Properties of Solids is the chapter on elasticity: stress, strain, the elastic moduli and the stress-strain curve. It is one of the smallest Physics chapters in NEET by question count, but it is also one of the quickest to prepare. Nearly every past question rests on a single definition, $Y = \frac{\text{stress}}{\text{strain}}$, or on reading the stress-strain curve correctly.

This post uses Pareeksha's own counts from the digitised NEET and AIPMT past papers, then works through five past questions with their official answers.

How often NEET asks Mechanical Properties of Solids

Across Pareeksha's 51 digitised papers from 1988 to 2026, 15 questions are tagged to this chapter. In the 18 NEET sittings from 2016 to 2026, it had 7 of 531 tagged Physics questions, which places it last, 29th of 29 Physics chapters.

The rate has stayed flat and low. The 8 NEET papers from 2016 to 2020 had 3 questions, and the 10 papers from 2021 to 2026 had 4, or 1.2% of the 347 tagged Physics questions in that period. Expect about one question every two or three papers.

NEET year (all sittings combined) Questions
2013 1
2016–2017 0
2018 1
2019 1
2020 1
2021–2022 0
2023 1
2024 2
2025 0
2026 1

Some years had more than one sitting, and a few digitised papers are a few questions short, so treat these as close counts. Low weight does not mean skip: the chapter takes a few hours, and its ideas (stress, pressure, bulk modulus) are reused in the fluids chapter. The full Physics table is on the NEET chapter-wise weightage page.

What the questions test

  1. Definitions of the moduli. Young's modulus, bulk modulus, compressibility, shear modulus and Poisson's ratio, often as a match-the-lists question.
  2. Elongation of wires. Find the stretch or the largest stretch within the elastic limit.
  3. Stress in a loaded wire. What the stress is and where.
  4. The stress-strain curve. Proportional limit, yield point, ultimate strength and fracture, and what they say about ductile and brittle materials.

Solved NEET past questions

Each question below is copied from the paper with its official answer. The working is ours.

1. Matching the elastic moduli

From NEET 2026 (cancelled May sitting), Q137.

Match List I with List II:

List I List II
A. Young's Modulus I. $\frac{\Delta d}{\Delta L}\left(\frac{L}{d}\right)$
B. Compressibility II. $\frac{FL}{A(\Delta L)}$
C. Bulk Modulus III. $-\frac{1}{\Delta P}\left(\frac{\Delta V}{V}\right)$
D. Poisson's Ratio IV. $-P\left(\frac{V}{\Delta V}\right)$

Choose the correct answer from the options given below:

  • (A) A-IV, B-I, C-II, D-III
  • (B) A-III, B-II, C-I, D-IV
  • (C) A-I, B-IV, C-III, D-II
  • (D) A-II, B-III, C-IV, D-I

Official answer: (D)

Solution. Write each from its definition. Young's modulus is $\frac{F/A}{\Delta L/L} = \frac{FL}{A\,\Delta L}$ (II). Bulk modulus is $-\frac{P}{\Delta V/V}$ (IV), and compressibility is its reciprocal (III). Poisson's ratio is lateral strain over longitudinal strain, $\frac{\Delta d/d}{\Delta L/L}$ (I). Once you place Young's modulus as II, only option (D) remains.

2. Largest stretch within the elastic limit

From NEET 2024, Q11.

The maximum elongation of a steel wire of 1 m length if the elastic limit of steel and its Young's modulus, respectively, are $8\times10^{8}\ \mathrm{N\,m^{-2}}$ and $2\times10^{11}\ \mathrm{N\,m^{-2}}$, is :

  • (A) 40 mm
  • (B) 8 mm
  • (C) 4 mm
  • (D) 0.4 mm

Official answer: (C)

Solution. The elastic limit is the largest stress the wire can take and still return to its length. Up to that stress, strain $= \frac{\text{stress}}{Y}$, so $\Delta L = \frac{\sigma L}{Y} = \frac{8 \times 10^8 \times 1}{2 \times 10^{11}} = 4 \times 10^{-3}$ m $= 4$ mm. The area of the wire is not needed, because the limit is given as a stress.

3. Stress in a hanging wire

From NEET 2023, Q10.

Let a wire be suspended from the ceiling (rigid support) and stretched by a weight $W$ attached at its free end. The longitudinal stress at any point of cross-sectional area $A$ of the wire is :

  • (A) $2W/A$
  • (B) $W/A$
  • (C) $W/2A$
  • (D) Zero

Official answer: (B)

Solution. For a light wire in equilibrium, the tension at every point equals the hanging weight W. Stress is force per area, so it is $\frac{W}{A}$ everywhere along the wire. Option (C) mixes this up with the stretch of a heavy wire under its own weight, where an average of half the weight appears.

4. Young's modulus from a stretched length

From NEET 2020 (Phase 1), Q161.

A wire of length $L$, area of cross section $A$ is hanging from a fixed support. The length of the wire changes to $L_1$ when mass $M$ is suspended from its free end. The expression for Young's modulus is :

  • (A) $\frac{MgL_1}{AL}$
  • (B) $\frac{Mg(L_1-L)}{AL}$
  • (C) $\frac{MgL}{AL_1}$
  • (D) $\frac{MgL}{A(L_1-L)}$

Official answer: (D)

Solution. Stress $= \frac{Mg}{A}$. Strain $= \frac{\Delta L}{L} = \frac{L_1 - L}{L}$, using the original length L in the denominator. So $Y = \frac{Mg/A}{(L_1 - L)/L} = \frac{MgL}{A(L_1 - L)}$. Option (B) is stress times strain, not stress divided by strain.

5. Reading a stress-strain curve

From NEET 2019 Odisha, Q176.

The stress-strain curves are drawn for two different materials X and Y. It is observed that the ultimate strength point and the fracture point are close to each other for material X but are far apart for material Y.

We can say that materials X and Y are likely to be (respectively),

  • (A) Plastic and ductile
  • (B) Ductile and brittle
  • (C) Brittle and ductile
  • (D) Brittle and plastic

Official answer: (C)

Solution. The gap between the ultimate strength point and the fracture point shows how much a material can deform plastically before it breaks. If the two points are close (X), the material breaks soon after reaching its highest stress: it is brittle. If they are far apart (Y), it stretches a lot before breaking: it is ductile.

Key formulas

Quantity Formula
Stress $\frac{F}{A}$ (units $\mathrm{N\,m^{-2}}$)
Longitudinal strain $\frac{\Delta L}{L}$ (no units)
Young's modulus $Y = \frac{FL}{A\,\Delta L}$
Bulk modulus $B = -\frac{\Delta P}{\Delta V/V}$
Compressibility $\frac{1}{B}$
Shear modulus $G = \frac{F/A}{\theta}$
Poisson's ratio $\frac{\Delta d/d}{\Delta L/L}$
Elastic energy per unit volume $\frac{1}{2} \times \text{stress} \times \text{strain}$
Stretch of a wire under its own weight $\frac{MgL}{2AY}$

Two facts worth remembering: the moduli depend on the material, not on the length or thickness of the sample; and for wires of the same material under the same load, $\Delta L \propto \frac{L}{r^2}$.

Common traps

  • Using the new length in strain. Strain is change in length over the original length.
  • Stress times strain instead of stress over strain. Check the formula by units: Young's modulus has the units of stress.
  • Thinking a thicker wire has a larger Young's modulus. It stretches less, but Y is a property of the material.
  • Millimetres and metres. Elongation answers are usually in mm; work in metres and convert at the end.
  • Mixing brittle and ductile. Close ultimate and fracture points mean brittle; far apart mean ductile.

How to study Mechanical Properties of Solids

  1. Read chapter 2 of the Pareeksha book Gravitation and Properties of Matter, also available in Hindi and Telugu.
  2. Make a half-page summary with the formula table above and a labelled stress-strain curve.
  3. Solve the chapter's past questions on the NEET past papers page. With only 15 in all the papers, you can do every one in a single sitting.
  4. Take the 15-question chapter test in the NEET section of your dashboard (login needed).
  5. Move on to the next chapter in the same book, Mechanical Properties of Fluids PYQs, which carries more weight. Thermal stress links this chapter with Thermal Properties of Matter PYQs.

Frequently asked questions

How many NEET questions come from Mechanical Properties of Solids?

Very few. In the NEET papers from 2016 to 2026 on Pareeksha it had 7 of 531 Physics questions, the lowest of the 29 Physics chapters. The 2021–2026 papers had 4.

Should I skip this chapter?

No. It takes only a few hours to prepare, the questions are mostly direct, and one question is worth the same as any other. Skipping it saves little time.

What is the most asked topic in this chapter?

Young's modulus and the elongation of wires, followed by the stress-strain curve and the definitions of the other moduli.

Does Young's modulus change if I cut a wire in half?

No. Young's modulus depends only on the material. The shorter wire stretches less under the same load, but its modulus is the same.

Share:𝕏fin
Put what you read into practice

Find study material for your next topic

Browse the Reading Room and preview a chapter before choosing what to study.

Browse study material →

Make this reading part of your preparation

Create your free account to bookmark Reading Room chapters and track your practice scores. You’ll return to this article after signing in.

By continuing, you agree to our terms and privacy policy.

No payment needed. Already registered? Use the same options to sign in.

Comments (0)

Sign in to join the discussion.

No comments yet. Be the first to share your thoughts.