LATEST
NEETBy Pareeksha Editorial Team· ⏱ 11 min read

Experimental Skills NEET Physics: All 18 Experiments

Share𝕏fin
Alongside this guide

Find study material for your next topic

Browse the Reading Room and preview a chapter before choosing what to study.

Browse study material →
Experimental Skills NEET Physics: All 18 Experiments
On this page
  1. How often it is asked
  2. The Unit 20 list
  3. Measuring instruments (experiments 1 and 2)
  4. Mechanics and properties of matter (experiments 3 to 7)
  5. Heat and sound (experiments 8 and 9)
  6. Electricity (experiments 10 to 12)
  7. Optics (experiments 13 to 15)
  8. Electronics (experiments 16 to 18)
  9. How to prepare this unit in a week
  10. Frequently asked questions
  11. How many questions come from experimental skills in NEET Physics?
  12. Do I need to have done the experiments in a lab?
  13. Is the potentiometer experiment still in the NEET syllabus?
  14. Is this unit worth studying if it has so few questions?

Experimental Skills is the last unit of the NEET Physics syllabus (Unit 20), and the one students most often leave out, since it carries few questions. But those questions are short, formula-based and predictable, and they have been appearing more often. This guide lists the 18 experiments, the formula or fact each depends on, and four solved past questions.

How often it is asked

In Pareeksha's tagged NEET papers, 8 Physics questions from 2016 to 2026 were from the measurement, mechanics and heat experiments, 6 of them in the 10 papers from 2021 to 2026. By year: 2 in 2020, 1 in 2021, 1 in 2024, 1 in 2025 and 3 in 2026 (across the cancelled May sitting and the June re-exam). No question in these papers was tagged to the electricity, optics and electronics experiments as such.

The numbers are small, so the trend could change. Also, experiment-flavoured questions are often tagged to their concept chapter: a NEET 2023 resistor colour-code question is counted under Current Electricity. The unit's real reach is wider than its own count.

The Unit 20 list

The NEET (UG) syllabus describes this unit as familiarity with the basic approach and observations of the following experiments and activities. The list below is from the syllabus document published by NMC and NTA (the NEET 2026 information bulletin states that the 2026 syllabus is unchanged from the previous year). Check the NEET 2027 information bulletin's syllabus when it is published.

No. Experiment (as listed in the syllabus, in brief) What it rests on
1 Vernier callipers: internal and external diameter and depth of a vessel least count, zero error
2 Screw gauge: thickness or diameter of a thin sheet or wire pitch, least count, zero error
3 Simple pendulum: energy loss, by plotting square of amplitude against time energy $\propto A^2$
4 Metre scale: mass of an object by the principle of moments $m_1d_1 = m_2d_2$
5 Young's modulus of the material of a metallic wire $Y = \frac{MgL}{\pi r^2\Delta l}$
6 Surface tension of water by capillary rise, and effect of detergents $S = \frac{rh\rho g}{2\cos\theta}$
7 Viscosity of a liquid from the terminal velocity of a sphere $\eta = \frac{2r^2(\rho - \sigma)g}{9v_t}$
8 Speed of sound in air using a resonance tube $v = 2f(l_2 - l_1)$
9 Specific heat capacity of a solid and a liquid by the method of mixtures heat lost = heat gained
10 Resistivity of a wire using a metre bridge $\frac{X}{R} = \frac{l}{100 - l}$, $\rho = \frac{X\pi D^2}{4L}$
11 Resistance of a wire using Ohm's law slope of $V$–$I$ graph
12 Resistance and figure of merit of a galvanometer by half deflection $G = \frac{RS}{R - S}$
13 Focal length of a convex mirror, a concave mirror and a convex lens by the parallax method mirror and lens formulas
14 Angle of deviation against angle of incidence for a triangular prism U-shaped curve, minimum deviation
15 Refractive index of a glass slab using a travelling microscope real depth over apparent depth
16 Characteristic curves of a p-n junction diode in forward and reverse bias knee voltage, reverse saturation
17 Characteristic curves of a Zener diode, and its reverse breakdown voltage breakdown in reverse bias
18 Identifying a diode, an LED, a resistor and a capacitor from a mixed collection how each conducts

Measuring instruments (experiments 1 and 2)

These two produced most of the recent questions.

Vernier callipers

  • Least count (vernier constant) $= 1\ \text{MSD} - 1\ \text{VSD}$
  • If $n$ vernier divisions equal $(n - 1)$ main-scale divisions, least count $= \frac{1\ \text{MSD}}{n}$
  • Reading $=$ main scale reading $+$ (coinciding vernier division $\times$ least count)
  • Zero error is positive when the vernier zero lies to the right of the main-scale zero with the jaws closed; corrected reading $=$ observed reading $-$ zero error (with its sign)

Screw gauge

  • Pitch $=$ distance the spindle moves in one full turn
  • Least count $= \frac{\text{pitch}}{\text{number of circular-scale divisions}}$
  • Reading $=$ main scale reading $+$ (circular scale reading $\times$ least count)
  • Zero error is handled the same way as in vernier callipers

Past question (NEET (UG) 2026, cancelled May sitting, Q160). In a vernier calliper, 20 VSD coincide with 16 MSD (each division of length 1 mm ). The least count of the vernier callipers is:

(A) 0.2 cm (B) 0.01 cm (C) 0.02 cm (D) 0.1 cm

Official answer: (C). 1 VSD $= \frac{16}{20}$ mm $= 0.8$ mm, so least count $= 1 - 0.8 = 0.2$ mm $= 0.02$ cm. Note this calliper does not follow the usual "$n$ VSD $= (n - 1)$ MSD" pattern, so go back to the definition.

Past question (NEET (UG) 2025, Q25). Consider the diameter of a spherical object being measured with the help of a Vernier callipers. Suppose its 10 Vernier Scale Divisions (V.S.D.) are equal to its 9 Main Scale Divisions (M.S.D.). The least division in the M.S. is 0.1 cm and the zero of V.S. is at $x = 0.1$ cm when the jaws of Vernier callipers are closed. If the main scale reading for the diameter is $M = 5$ cm and the number of coinciding vernier division is 8, the measured diameter after zero error correction, is

(A) 5.18 cm (B) 5.08 cm (C) 4.98 cm (D) 5.00 cm

Official answer: (C). Least count $= 0.1 - 0.09 = 0.01$ cm. Observed reading $= 5 + 8 \times 0.01 = 5.08$ cm. The zero error is $+0.1$ cm, so the corrected diameter is $5.08 - 0.1 = 4.98$ cm. Options (A) and (B) are the "added the error" and "forgot the error" answers.

Past question (NEET (UG) 2021, Q6). A screw gauge gives the following readings when used to measure the diameter of a wire Main scale reading : 0 mm Circular scale reading : 52 divisions Given that 1 mm on main scale corresponds to 100 divisions on the circular scale. The diameter of the wire from the above data is :

(A) 0.52 cm (B) 0.026 cm (C) 0.26 cm (D) 0.052 cm

Official answer: (D). Least count $= \frac{1\ \text{mm}}{100} = 0.01$ mm. Reading $= 0 + 52 \times 0.01 = 0.52$ mm $= 0.052$ cm. Option (A) is the same number with the wrong unit.

Mechanics and properties of matter (experiments 3 to 7)

  • Simple pendulum. The energy of an oscillation is proportional to the square of its amplitude, so a graph of $A^2$ against time shows how quickly energy is lost to air resistance and friction. It falls, steeply at first and then more slowly. The period itself is $T = 2\pi\sqrt{\frac{l}{g}}$.
  • Principle of moments. A metre scale balanced on a knife edge, with a known mass $M$ at distance $d_1$ on one side and the unknown $m$ at $d_2$ on the other, gives $m = \frac{Md_1}{d_2}$ (once the scale's own weight is balanced).
  • Young's modulus. A wire of length $L$ and radius $r$ stretches by $\Delta l$ under load $Mg$: $Y = \frac{MgL}{\pi r^2\Delta l}$. The load–extension graph is a straight line within the elastic limit; $Y$ comes from its slope. The radius is measured with a screw gauge, and since $r$ is squared, its error counts twice.
  • Surface tension. Water rises in a clean glass capillary of radius $r$ to height $h = \frac{2S\cos\theta}{r\rho g}$; with contact angle close to zero, $S = \frac{rh\rho g}{2}$. Adding detergent lowers $S$, so the rise falls. A narrower tube gives a higher rise.
  • Viscosity. A small sphere falling through a viscous liquid soon moves at constant terminal velocity $v_t$. Then $\eta = \frac{2r^2(\rho - \sigma)g}{9v_t}$, where $\rho$ is the sphere's density and $\sigma$ the liquid's. Timing starts only after the ball has reached terminal velocity.

Heat and sound (experiments 8 and 9)

  • Resonance tube. For the first two resonances, $l_1 + e = \frac{\lambda}{4}$ and $l_2 + e = \frac{3\lambda}{4}$, where $e$ is the end correction. Subtracting, $l_2 - l_1 = \frac{\lambda}{2}$, so $v = 2f(l_2 - l_1)$, and the end correction cancels. Also $e = \frac{l_2 - 3l_1}{2}$. With $f = 512$ Hz, $l_1 = 16.0$ cm and $l_2 = 50.0$ cm: $v = 2 \times 512 \times 0.340 \approx 348$ m/s, and $e = \frac{50.0 - 48.0}{2} = 1.0$ cm.
  • Method of mixtures. A hot solid of mass $m_s$ at $T_s$ dropped into water of mass $m_w$ at $T_w$ in a calorimeter reaches $T$. Then $m_sc_s(T_s - T) = (m_wc_w + m_cc_c)(T - T_w)$. Heat losses to the surroundings make the measured specific heat come out low, so the transfer is done quickly.

Electricity (experiments 10 to 12)

  • Metre bridge. With the unknown $X$ in the left gap, a known $R$ in the right gap and balance at $l$ cm from the left end, $\frac{X}{R} = \frac{l}{100 - l}$. Resistivity is then $\rho = \frac{X\pi D^2}{4L}$, with $D$ from a screw gauge. Readings are most accurate when the balance point is near the middle of the wire, because end resistances matter least there.
  • Ohm's law. Plot $V$ against $I$ for the wire; the slope is $R$.
  • Half deflection. With a high resistance $R$ in series, note the deflection $\theta$; add a shunt $S$ across the galvanometer until the deflection halves. Then $G = \frac{RS}{R - S}$, close to $S$ when $R$ is much larger. Figure of merit is the current per division, $k = \frac{I}{\theta}$.

Optics (experiments 13 to 15)

  • Parallax method. A needle is moved until it shows no parallax with the image (they move together as you shift your eye). For a concave mirror and a convex lens with real images, $f = \frac{uv}{u + v}$, taking $u$ and $v$ as positive distances. A convex mirror forms only a virtual image, so a convex lens is used with it to obtain a real image first.
  • Prism. A graph of deviation $\delta$ against incidence $i$ is U-shaped. At the bottom, $i = e$ and the deviation is minimum, giving $n = \frac{\sin\left(\frac{A + \delta_m}{2}\right)}{\sin\left(\frac{A}{2}\right)}$.
  • Travelling microscope. Focus on a mark without the slab (reading $R_1$), on the same mark through the slab ($R_2$) and on the top of the slab ($R_3$). Real thickness $= R_3 - R_1$, apparent thickness $= R_3 - R_2$, and $n = \frac{R_3 - R_1}{R_3 - R_2}$.

On an optical bench, the distance read between two uprights may not equal the actual distance between the lens and the needle; measuring a rod of known length fixes this, which is called the index correction.

Past question (NEET (UG) 2026 Re-exam, Q20). Which of the following measurements require 'index correction' ?

(A) Measurement of resistance of a wire using meter bridge (B) Measurement of gravitational acceleration using simple pendulum (C) Measurement of focal length of lenses using optical bench (D) Measurement of speed of sound using resonance tube

Official answer: (C).

Electronics (experiments 16 to 18)

  • p-n diode. In forward bias, current stays tiny until the knee voltage (about 0.7 V for silicon), then rises steeply. In reverse bias, a very small, nearly constant reverse saturation current flows.
  • Zener diode. In reverse bias the current stays tiny until the breakdown voltage, then rises sharply while the voltage stays almost fixed. That fixed voltage is why it is used as a regulator.
  • Identifying components with a multimeter. A resistor conducts equally in both directions. A diode conducts in one direction only. An LED conducts in one direction and glows. A capacitor shows a brief current that falls to zero (the meter needle kicks and returns) and then does not conduct.

How to prepare this unit in a week

Give the first two days to vernier callipers and screw gauge (20 reading and zero-error questions), since they are asked most. Then one day each for experiments 3 to 7, heat and sound, the electrical experiments, the optics experiments, and electronics, ending with a mixed test.

The Experimental Skills book has chapters on measurement, mechanics and heat and electricity, optics and electronics, in English, Hindi and Telugu; the longer Unit 20 book adds worked examples. Past questions are in the experiments PYQ post, least count and error rules in units and dimensions for NEET, and Chemistry's matching unit in practical chemistry for NEET. See also the syllabus page and the weightage page.

Frequently asked questions

How many questions come from experimental skills in NEET Physics?

In the 10 NEET papers from 2021 to 2026 on Pareeksha, 6 Physics questions were tagged to the measurement, mechanics and heat experiments, 3 of them in 2026. Related questions, such as resistor colour codes, are sometimes tagged to their concept chapters instead.

Do I need to have done the experiments in a lab?

It helps, but it is not required. NEET asks about the principle, the formula, the reading and the common errors, all of which can be learnt from a diagram and a description.

Is the potentiometer experiment still in the NEET syllabus?

It is not in the current Unit 20 list. The electrical experiments listed are the metre bridge, Ohm's law and the galvanometer by half deflection, plus the diode and Zener diode characteristics.

Is this unit worth studying if it has so few questions?

Yes, because the cost is low. About a week of light study covers it, and the questions take under a minute when you know the formula. Skipping it gives away easy marks: the two 2026 papers had three such questions between them.

Share:𝕏fin
Put what you read into practice

Find study material for your next topic

Browse the Reading Room and preview a chapter before choosing what to study.

Browse study material →

Make this reading part of your preparation

Create your free account to bookmark Reading Room chapters and track your practice scores. You’ll return to this article after signing in.

By continuing, you agree to our terms and privacy policy.

No payment needed. Already registered? Use the same options to sign in.

Comments (0)

Sign in to join the discussion.

No comments yet. Be the first to share your thoughts.